FAZ 3000-DCF DCF module - produktinfo.conrad.com
Contents
1. workshop Clean the product with a soft clean dry and lint free cloth To remove heavier dirt use a cloth which is slightly moistened with lukewarm water Do not use any solvent based cleaning agents as these may damage the plastic casing 10 Disposal When the product is no longer usable dispose of it in accordance with the applicable statutory regulations 11 Technical specifications Connection to the FAZ 3000 2 alarm base station Power is supplied by the FAZ 3000 2 alarm base station Operating voltage 5V power consumption approximately 10mA DCF radio signal reception frequency 77 5kHz can be received within a radius of approximately 1500 2000km around Mainflingen near Frankfurt am Main Can be wall mounted Dimensions 51mm x 76mm x 20mm W x H x D 12 12 Declaration of conformity DOC We Conrad Electronic Klaus Conrad Stra e 1 92240 Hirschau Germany hereby declare that this product complies with the fundamental requirements and other relevant regulations of directive 1999 5 EC IS You can find the declaration of conformity for this product at www conrad com 13 14 152. 0 Z alarm base station accurately and automatically The product should only be used in dry indoor areas Any use other than the one described above may damage the product and can also increase the risk of short circuit fire electric shock etc No part of the product may be modified or adapted All the safety instructions and installation notes in this manual must be observed without fail 3 Scope of delivery FAZ 3000 DCF DCF module with a connecting cable User manual 4 Explanation of icons The icon with a lightning flash in a triangle is used to alert you to potential personal injury hazards such as electric shock The icon with an exclamation mark in a triangle points to important information in this user manual that must be observed The hand symbol indicates special tips and information on operation E 5 Safety instructions The product s guarantee becomes invalid if the product is damaged as a result of the failure to observe these operating instructions We do not assume any liability for any result ing damages We do not assume liability for damage to property or personal injury caused by improper use or failure to observe the safety instructions In such cases the product s guaran tee becomes invalid Dear customer the following safety instructions are intended to protect you as well as the device Please take time to read through the following points If you are not sure h
3. b Opening the casing of the alarm base station connection 7 Installation Reception check configuration Maintenance and cleaning cceececeeeeeeeeeeeeeceeeeseeeeeeeeeeeeseaeeeneeeens 12 DISPO inicio Sia 12 Technical Specifications oonooocnnnnidinnccnnccnocncnornnnncnnnrnnnnccnnrnncancnnnnos 12 Declaration of conformity DOC ooooonocccicccconccconcnoncconancnnncnoncnnnncannno 13 1 Introduction Dear customer Thank you for purchasing this product This product meets the requirements of both current national and European guidelines In order to ensure continued fulfilment of legal requirements and safe operation of this product we kindly ask you to carefully follow the instructions in this user manual Please read the user manual completely and observe the safety and operation instructions before using the product All company and product names contained herein are trademarks of their respective owners All rights reserved Should you have any further questions please contact our technical service Germany Tel no 49 9604 40 88 80 Fax no 49 9604 40 88 48 Email tkb conrad de Mon to Thur 8 00am to 4 30pm Fri 8 00am to 2 00pm 2 Prescribed use The FAZ 3000 DCF DCF module functions exclusively with the FAZ 3000 wireless alarm system This radio controlled module is used to receive the DCF signal in order to set the time and the date of the FAZ 300
4. enu see the figure to the right This appears only when the alarm base station receives a data packet from the DCF module Confirm your selection by briefly pressing the OK button Either the lower or the upper display appears depending on whether the DCF time has been already synchronised or not see the figure to the right If synchronous appears on the lower line then the DCF time has been received correctly and the time and the date are automatically set per DCF A blinking square on the upper line indicates a received DCF signal You can use the 4 and Y buttons to activate active or deactivate off the DCF receiver DCF active DCF receiver is switched on The DCF signal is searched for after switching on it must be first re synchronised this may take a few minutes DCF off DCF receiver is switched off Pressing the OK button applies the setting Exit this menu by pressing the C button twice you are guided back to the normal display mode main menu of the alarm base station setup DCF setup DCF active not synchr DCF active synchronous DCF off not synchr DCF active not synchr disarm 17 27 22 02 11 9 Maintenance and cleaning This product does not require maintenance never try to open it Any repairs should be carried out by a skilled technician or a professional
5. http www conrad com OPERATING INSTRUCTIONS 100 recycled paper Bleached without chlorine Imprint These operating instructions are published by Conrad Electronic SE Klaus Conrad Str 1 D 92240 Hirschau Germany All rights reserved No reproduction including translation is permitted in whole or part e g photocopying microfilming or storage in electronic data processing equipment without the express written consent of the publisher The operating instructions reflect the current technical specifications at the time of print We reserve the right to change the technical or physical specifications Copyright 2007 by Conrad Electronic SE Printed in Germany Version 01 07 ce FAZ 3000 DCF DCF module Item no 75 04 06 This user manual belongs to this product It contains important information specific to its operation and handling Please bear this in mind when passing on the product to a third party Therefore keep this user manual for future reference A contents list can be found in the table of contents on page 2 QINRAD ELECTRONIC Table of contents NIIT PMN 7 8 9 10 11 12 Page Intraduction Susanne 4 Praseribedasen usunsn ass 4 Scope of delve ARPPPERSTHTTSTEPERFEFEREFSEFESFPERTELENTERETETFITFFERTERDEITPEETEEREEFTE EEE 4 Explanation Of CONS lt iociinnsi nidad 4 Safety instructions Connecting to the alarm base station 6 a Preparation He
6. on check configuration An LED is located on the front side of the DCF module which is used for checking the radio signal Position the module such that the LED flashes briefly every second A pulse is not received in the 59th second indicating the beginning of a new data packet and not an erroneous defective reception After receiving the first reception pulse the alarm base station sets the configuration menu for DCF reception automatically You can use the DCF setup menu of the alarm base station available only if a DCF module has been connected to switch on or switch off the DCF receiver manually You can also check whether synchronisation takes place IS It may take a few minutes until the DCF time date are set You can switch the DCF receiver on or off via the DCF setup menu You can also check whether a synchronisation has taken place reception check Proceed as follows The alarm base station must be in the top level The disarm LCD should appear as on the right for example with the time and the date 17 25 22 02 Briefly press the Men a A button on the control troubles unit of the FAZ Z alarm base station Use the 4 and y buttons to select the setup setu menu see the figure to the right P Confirm your selection by briefly pressing the OK setup purton set time 10 Use the 4 and buttons to select the DCF setup m
7. ow to assemble connect and install the device or if you have doubts about its mode of operation contact a skilled technician For safety and licensing CE reasons any unauthorised alterations to and or modification of the product are not permitted The product is only suitable for use in dry indoor areas Make sure it does not get damp or wet This product is not a toy and should be kept out of the reach of children Do not leave packaging material lying around This may become a dangerous plaything in the hands of children Handle the product with care knocks blows or even a fall from a low height can damage it 6 Connecting to the alarm base station a Preparation IS If you wish to connect the DCF module to an alarm base station thatis already in operation you must first set the alarm bas station to the maintenance mode The alarm base station will otherwise trigger a sabotage alarm The alarm base station must be in the top level The LCD should appear as on the right for example with the time and the date Briefly press the Men a A button on the control unit of the FAZ Z alarm base station Use the 4 and buttons to select the service menu See the figure on the right Confirm your selection by briefly pressing the OK button The first sensor that was registered with the alarm base station is displayed Keep pressing the gt button until center is displa
8. pper half of the casing must snap in Exit the maintenance mode of the alarm base station by pressing the OK button briefly and then pressing the C button twice You are guided back to the main menu of the alarm base station time date display 7 Installation IS The DCF module should be installed at the as far away as possible from the alarm base station and all other electrical or metallic devices in order to ensure the flawless reception of the DCF signal An LED is located on the front side of the DCF module which is used for checking the radio signal If the reception is flawless the LED should blink every second a pulse is not received in the 59th second indicating the beginning of a new data packet and not an erroneous defective reception The DCF module can be installed either using the adhesive mounting or both screw openings IS Before drilling the mounting holes check whether the DCF radio reception is flawless Mount the DCF module temporarily and check in the menu of the alarm base station that the reception at the installation location is flawless The DCF module can be then mounted on the wall using screws Depending on the wall drill two holes and insert suitable dowels to fix the screws The DCF module can be then mounted on the wall When drilling or fastening screws be careful not to damage any power supply lines gas or water pipes as this could pose a life threatening danger 8 Recepti
9. yed in the top row Confirm your selection by briefly pressing the OK button The casing of the alarm base station can now be opened without triggering a sabotage alarm Proceed as follows to set the alarm base station to the maintenance mode disarm 17 25 22 02 troubles service contact 1 livingr w1 center center service b Opening the casing of the base station connection Press both catches see the arrows in figure 1 inwards carefully approxi mately one millimetre using a flat screwdriver until both half shells can be removed from each other First press one catch inwards and pull the casing approx 2 3 millimetres apart at this location Then press the other catch inwards the casing now opens First lift the alarm base station slightly from the wall to be able to guide the connector of the DCF module through the casing opening at the rear side of FAZ 3000 2 Unscrew the casing screw inside FAZ 3000 2 for this purpose if re quired see figure 2 000 aloo bebe A khet EBEN Figure 1 Then push the plug of the DCF module connecting cable into the BU2 socket until it snaps in see the arrow in figure 2 KL1 KL2 KL3 KL4 KL5 KL6 un m SISMANFEITNT ig cS si2 Socket BU2 Casing screw Figure 2 Then re tighten the casing screw Close the casing the u
Download Pdf Manuals
Related Search