Australia - New Zealand
Contents
1. the chainsaw which could result in serious personal injury Do not rely exclusively upon the safety devices built into your chainsaw As a chainsaw user you should take several steps to keep your cutting jobs free from accident or injury Kickback is the result of tool misuse and or incorrect operat ing procedures or conditions and can be avoided by taking proper precautions as given below Maintain a firm grip with thumbs and fingers encir cling the chainsaw handles With both hands on the chainsaw position your body and arm to allow you to resist kickback forces Kickback forces can be control led by the operator if proper precautions are taken Do not let go of the chainsaw Do not overreach and do not cut above shoulder height This helps prevent unintended tip contact and enables better control of the chainsaw in unexpected situ ations Only use replacement guide bars and chains specified by the manufacturer Incorrect replacement guide bars and chains may cause chain breakage and or kickback Follow the manufacturer s sharpening and mainte nance instructions for the saw chain Decreasing the depth gauge height can lead to increased kickback Striking metal cement or any other hard material near the wood or buried in the wood can cause kickback A dull or loose chain can cause kickback Do not try to insert into a previous cut As this could cause kickback Make a fresh cut every time Safety recommendat2. battery from the tool Directive 2000 14 EC guaranteed sound powe r Chain oil Ne Eso E Moving direction of the chain Marked under teh sprocket cover Hold operate the saw properly with both hands Do not operate the saw using only one hand Contact of teh guide bar tip with any object should be avoided Tip contact may case the guide bar to move suddenly upward and backward which may cause serious injury h da s SE 1 o Warning Do not touch chain at the chip MO ejection point AA Caution Do not over tighten Tighten by hand Finger tight only Additional safety instructions for batteries and chargers Batteries Never attempt to open for any reason Do not expose the battery to water Do not store in locations where the temperature may exceed 40 C Charge only at ambient temperatures between 10 C and 40 C Charge only using the charger provided with the tool When disposing of batteries follow the instructions given in the section Protecting the environment Do not attempt to charge damaged batteries gt Original instructions Chargers Use your BLACK DECKER charger only to charge the battery in the tool with which it was supplied Other batter ies could burst causing personal injury and damage Never attempt to charge non rechargeable batteries Have defective cords replaced immedi
3. instructions Failure to follow the warnings and injury instructions listed below may result in electric b Use personal protective equipment Always wear eye shock fire and or serious injury protection Protective equipment such as dust mask non skid safety shoes hard hat or hearing protection Save all warnings and instructions for future reference used for appropriate conditions will reduce personal The term power tool in all of the warnings listed below refers injuries to your mains operated corded power tool or battery oper c Prevent unintentional starting Ensure the switch is in ated cordless power tool the off position before connecting to power source 1 Work area safety Keep work area clean and well lit Cluttered or dark areas invite accidents Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep children and bystanders away while operating a power tool Distractions can cause you to lose control Electrical safety Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk o
4. local by laws or regulations that would prohibit or control the pruning of the tree limbs Pruning should only be undertaken by experienced users there is an increased risk of the saw chain pinching and kick back Before pruning consideration should be given to conditions affecting the direction of fall including The length and weight of the branch to be cut Any unusual heavy limb structure or decay Surrounding trees and obstacles including overhead The wind speed and direction The branch being intertwined with other branches The operator should consider access to the tree limb and the direction of fall The tree branch is liable to swing towards the tree trunk In addition to the user bystanders objects and property below the branch will be at risk To avoid splintering make the first cut in an upward direc tion to a maximum depth of one third the diameter of the branch Make the second cut downwards to meet the first Logging fig S T 8 U How you should cut depends on how the log is supported Use a saw horse whenever possible Always start a cut with the saw chain running and the spiked bumper 20 in contact with the wood fig S To complete the cut use a pivoting ac tion of the spiked bumper against the wood When supported along its whole length Make a downward cut but avoid cutting the earth as this will blunt your saw chain quickly When supported at both ends First cut one third down to
5. oiled before each use and after cleaning using only the correct grade of oil cat no A6023 QZ Lubricate the saw chain 6 by slowly pressing the bulb 17 fig O on the oil cap 3 four time before making each cut Hold the bulb down for 1 second each time Switching on fig O Grip your chainsaw firmly with both hands Pull the lock off button 2 with your thumb and then push the on off switch 1 to start When the motor starts remove your thumb from the lock off button 2 and grip the handle firmly Do not force the tool allow the tool to do the work It will do a better and safer job at the speed for which it is designed Excessive force will stretch the saw chain 6 If the saw chain 6 or guide bar 7 becomes jammed Switch the tool off Remove the battery 12 Open the cut with wedges to relieve the strain on the guide bar 7 Do not try to wrench the chainsaw free Start a fresh cut gt Original instructions Felling fig P Q amp R Inexperienced users should not attempt to fell trees The user may suffer injury or cause damage to property as a result of failure to control the direction of fall the tree may splinter or damaged dead branches may fall during cutting The safe distance between a tree to be felled and bystanders buildings and other objects is at least 2 1 2 times the height of the tree Any bystander building or object within this distance is at risk from bei
6. andard test method provided by EN 60745 and may be used for comparing one tool with another The declared vibration emission value may also be used in a preliminary assessment of exposure Warning The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used The vibration level may increase above the level stated When assessing vibration exposure to determine safety measures required by 2002 44 EC to protect persons regularly using power tools in employment an estimation of vibration exposure should consider the actual conditions of use and the way the tool is used including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time Labels on tool The following pictograms are shown on the tool Warning Read the manual prior to operation Warning To reduce the risk of injury the user must read the instruction manual EB E Wear eye ear and head protectionwhen using this product m Wear non silp safety footwear when using the product Wear non silp heavy dutygloves when using this product Do not expose the tool to rain or high humidit y gt Keep bystanders away I A Original instructions gt ap Switch the tool off Before performing any re maintenance on the tool remove the
7. ately Do not expose the charger to water Do not open the charger Do not probe the charger e A The charger is intended for indoor use only ill Read the instruction manual before use Electrical safety Your charger is double insulated therefore no earth wire is required Always check that the mains voltage corresponds to the voltage on the rating plate Never attempt to replace the charger unit with a regular mains plug If the supply cord is damaged it must be replaced by the manufacturer or an authorised Black amp Decker Service Centre in order to avoid a hazard Features 1 On off switch 2 Lock off button 3 Oil cap 4 Front guard 5 Chain tension adjustment ring 6 Chain 7 Guide bar 8 Chain sheath 9 Chain adjust locking knob 10 Chain cover assembly 11 Oil level indicator 12 Battery Assembly Warning Always wear protective gloves when working on your chainsaw Warning Before performing any assembly or maintenance on power tools switch off and remove the battery Warning Remove the cable tie that attaches the chain to the chainbar before assembly P P P Fitting the guide bar and chain fig L Place the chainsaw onto a stable surface fig A Fully loosen the chain adjust locking knob 9 fig B Remove the chain cover assembly 10 fig C Turn the tension adjust ring 5 anti clockwise as far as it will go so the arrow on th
8. avoid splintering and second cut up to meet the first cut When supported at one end First cut one third up to avoid splintering and second cut down to prevent splintering When on a slope Always stand on the uphill side When attempting to cut a log on the ground fig T Secure the workpiece using chocks or wedges The user or a bystander should not steady the log by sitting or standing on it Make sure that the saw chain does not contact the ground When using a saw horse fig U This is strongly recommended whenever possible Position the log in a stable position Always cut on the outside of the saw horse arms Use clamps or straps to secure the workpiece Limbing fig V Removing the branches from a fallen tree When limbing leave larger lower limbs to support the log off the ground Remove the small limbs in one cut Branches under tension should be cut from the bottom of the branch towards the top to avoid binding the chain saw Trim limbs from opposite side keeping tree stem between you and saw Never make cuts with saw between your legs or straddle the limb to be cut 2 Troubleshooting Problem Possible solution Tool will not start Lock button not Press the lock button pressed Battery not fitted Fit the battery Battery not charged Charge the battery Battery not fitted Remove then re fit the corectly battery Chain does not stop Chain tension is too Check chain tension within 2 secon
9. bar 7 and the saw chain 6 and clean them thoroughly Make sure that the guard is clean and free from debris Oil sprocket nose and chain bar via the sprocket lubrica tion holes 21 fig E This ensures an even distribution of wear around the guide bar rails Saw chain sharpening If you are to get the best possible performance from the tool it is important to keep the teeth of the saw chain sharp Guidance for this procedure is found on the sharpener pack age Replacing worn out saw chains Replacement saw chains are available through retailers or Black amp Decker service agents Always use genuine spare parts Replacements chain part number A6125CSL XJ Saw chain sharpness The saw chain cutters will blunt immediately if they touch the ground or a nail while cutting Saw chain tension Regularly check the saw chain tension What to do if your chainsaw needs repair Your chainsaw is manufactured in accordance with the rel evant safety requirements Repairs should only be carried out by a qualified person using original spare parts otherwise this may result in considerable danger to the user We recommend you keep this user manual in a safe place gt Original instructions Protecting the environment Should you find one day that your Black amp Decker product needs replacement or if it is of no further use to you do not dispose of it with household waste Make this product avail able for separate collec
10. de bar 7 and the chain 6 on the underside Note Do not over tension the chain as this will lead to excessive wear and will reduce the life of the guide bar and the chain Note When the chain is new check the tension frequently after disconnecting from the mains during the first 2 hours of use because a new chain stretches slightly To increase the tension fig J K amp L Turn the chain adjust locking knob 9 180 degrees anti clockwise to release the tension fig J Tension the chain using the chain tension adjusting ring 5 turn clockwise to tighten fig K Tighten the chain adjust locking knob 9 fig L Fitting and removing the battery fig M To fit the battery 12 line it up with the receptacle on the tool Slide the battery into the receptacle and push until the battery snaps into place To remove the battery push the release buttons 16 while at the same time pulling the battery out of the receptacle Use Warning Let the tool work at its own pace Do not overload Charging the battery fig N The battery needs to be charged before first use and whenev er it fails to produce sufficient power on jobs that were easily done before The battery may become warm while charging this is normal and does not indicate a problem Warning Do not charge the battery at ambient temperatures below 10 C or above 40 C Recommended charging tem perature approx 24 C Note The charg
11. ds slack when the tool is switched off Check oil tank level Clean oil holes 21 fig Bar chain appear hot Oil tank empty smoking Oil hole blocked on chain bar E and clear the groove around the edge of the chainbar Chain tension is too Check chain tension tight Guide bar sprocket Oil the guide bar nose needs greasing sprocket nose Chainsaw does not cut well Chain on backwards Check modify chain direction Sharpen Chainsaw not using Debris in tank Empty oil from tank and oil replace Oil hole in cap blocked Remove debris from hole Debris in chain bar Remove debris and clean the chain bar Debris in oil outlet Remove debris Chainsaw stops Battery depleted Re charge battery if suddnely during use required Battery too hot Leave the battery to cool for atleast 30 minutes before proceeding or charging Voltage limit protection Restart the chainsaw Let the tool work at its own pace Do not overload Original instructions gt Maintenance Regular maintenance ensures a long effective life for the tool We recommend you make the following checks on a regular basis Warning Before performing any maintenance on power tools Switch off and disconnect the tool from the mains supply Oil level The level in the reservoir should not be allowed to fall below a quarter full Saw chain and guide bar After every few hours of use and before storage remove the guide
12. e Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source and or the battery pack from the power tool before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally 6 7 Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tools operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions taking into account the working conditions and the work to be performed Use of the power tool for operations different fro
13. e 70 5 dB A Uncertainty K 1 5 dB A 5 Lwa sound power 90 5 dB A Uncertainty K 1 5 dB A Vibration total values triax vector sum according to EN 60745 Vibration emission value 4 49 mis uncertainty K 1 5 mis Australia amp New Zealand Stanley Black amp Decker www blackanddecker com au www blackanddecker co nz Tel 1800 338 002 Aust or Tel 0800 339 258 NZ 90624127 04 2015
14. e appropriate measures for the protection of hearing When handling the product the chain bar may become hot handle with care Safety of others This appliance is not intended for use by persons includ ing children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concern ing use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Residual risks Additional residual risks may arise when using the tool which may not be included in the enclosed safety warnings These risks can arise from misuse prolonged use etc Even with the application of the relevant safety regulations and the implementation of safety devices certain residual risks can not be avoided These include Injuries caused by touching any rotating moving parts Injuries caused when changing any parts blades or ac cessories ee e Injuries caused by prolonged use of a tool When using any tool for prolonged periods ensure you take regular breaks Impairment of hearing Health hazards caused by breathing dust developed when using your tool example working with wood especially oak beech and MDF Vibration The declared vibration emission values stated in the technical data and the declaration of conformity have been measured in accordance with a st
15. e tension adjust ring 5 lines up with the marker on the chain cover assembly 13 fig D Place the chain 6 over the guide bar 7 making sure that the saw chain cutters on the upper part of the guide bar 7 face towards the front fig E Guide the chain 6 around the guide bar 7 and pull it to create a loop to one side at the rear end of the guide bar 7 Guide the chain 6 around the drive sprocket 14 Place the guide bar 7 onto the bar location studs 15 fig F amp G Place the chain cover assembly 10 onto the chainsaw fig H making sure the arrows are aligned fig Turn the chain adjust locking knob 9 clockwise to attach the chain cover assembly 10 and lightly tighten fig 1 Turn the chain adjust locking knob 9 180 degrees anti clockwise to release the tension fig J Turn the chain tension adjust ring 5 clockwise until the chain 6 is tight Make sure that the chain 6 is snug around the guide bar 7 fig K Check the tension as described below Do not overtighten Tighten the chain adjust locking knob 9 L Checking and adjusting the chain tension fig K Before use and after every 10 minutes of use you must check the chain tension Remove the battery 12 Lightly pull on the chain 6 as shown inset fig K The tension is correct when the chain 6 snaps back after being pulled 3 mm away from the guide bar 7 There should be no sag between the gui
16. er will not charge a battery if the cell temperature is below approximately 10 C or above 40 C The battery should be left in the charger and the charger will begin to charge automatically when the cell tempera ture warms up or cools down To charge the battery 12 insert it into the charger 19 The battery will only fit into the charger in one way Do not force Be sure that the battery is fully seated in the charger Plug in the charger and switch on at the mains The charging indicator 18 will blink The charge is complete when the charging indicator 18 switches to continuously on The charger and the battery can be left connected indefinitely The charging indicator will switch on as the charger occasionally tops up the battery charge Charge discharged batteries within 1 week Battery life will be greatly diminished if stored in a discharged state Leaving the battery in the charger The charger and battery pack can be left connected with the charging indicator glowing indefinitely The charger will keep the battery pack fresh and fully charged Charger diagnostics If the charger detects a weak or damaged battery the charg ing indicator 18 will flash red at a fast rate Proceed as follows Re insert the battery 12 If the charging indicators continues flashing red at a fast rate use a different battery to determine if the charging process works properly If the replaced battery charges correctl
17. f electric shock if your body is earthed or grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock and or battery pack picking up or carrying the tool Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents Remove any adjusting key or wrench before turning the power tool on A wrench or a key left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of dust collection can reduce dust related hazards Power tool use and car
18. ions for the chainsaw We strongly recommend that first time users obtain practi cal instruction in the use of the chainsaw and protective equipment from an experienced user Initial practice should be completed sawing logs on a saw horse or cradle We recommend that when carrying the chainsaw that you remove the battery and make sure that the saw chain is facing backwards Maintain your chainsaw when not in use Do not store your chainsaw for any length of time without first remov ing the saw chain and guide bar which should be kept immersed in oil Store all parts of your chainsaw in a dry secure place out of reach of children We recommend you drain the oil reservoir prior to storage Be sure of your footing and pre plan a safe exit from a falling tree or branches Use wedges to help control felling and prevent binding the guide bar and saw chain in the cut Saw chain care Keep the saw chain sharp and snug on the guide bar Ensure the saw chain and guide bar are clean and well oiled Keep handles dry clean and free from oil and grease Avoid cutting Prepared timber Into the ground Into wire fences nails etc Additional safety instructions Ensure someone is nearby but at a safe distance in case of an accident If for any reason you have to touch the saw chain make sure your chainsaw is disconnected from the mains The noise from this product can exceed 85 dB A We therefore recommend you tak
19. m those intended could result in a hazardous situation 5 Battery tool use and care a Recharge only with the charger specified by the manufacturer A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack Use power tools only with specifically designated battery packs Use of any other battery packs may create a risk of injury and fire When battery pack is not in use keep it away from other metal objects like paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery terminals together may cause burns or a fire Under abusive conditions liquid may be ejected from the battery avoid contact If contact accidentally occurs flush with water If liquid contacts eyes additionally seek medical help Liquid ejected from the battery may cause irritation or burns Service Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained Power to the tool should always be supplied via residual current device with a rated residual current of 30mA or less Original instructions gt Additional power tool safety warnings Warning Additional safety warnings for chainsaws Keep all parts of the body away from the saw chain when the chainsaw is operating Before you star
20. ng struck by the tree when felled Before attempting to fell a tree Make sure that there are no local by laws or regulations that would prohibit or control the felling of the tree Consider all conditions that may affect the direction of fall including The intended direction of fall The natural lean of the tree Any unusual heavy limb structure or decay Surrounding trees and obstacles including overhead lines and underground drains The wind speed and direction Pre plan a safe exit from falling trees or branches Make sure that the exit route is clear of obstacles that would prevent or hinder movement Remember that wet grass and freshly cut bark is slippery Do not attempt to fell trees where the tree diameter is greater than the cutting length of the chainsaw Cut direction notch to determine the direction of fall Make a horizontal cut to a depth of between 1 5th and 1 3rd of the diameter of the tree perpendicular to the line of fall at the base of the tree fig P Make a second cut from above to intersect with the first and make a notch of about 45 Make a single horizontal felling cut from the other side 25 mm to 50 mm above the centre of the direction notch fig Q Do not cut through to the direction notch you could lose control of the direction of fall Drive a wedge or wedges into the felling cut to open it and drop the tree fig R Pruning trees Make sure that there are no
21. plings The slender material may catch the saw chain and be whipped toward you or pull you off balance Carry the chain saw by the front handle with the chain saw switched off and away from your body When transporting or storing the chainsaw always fit the guide bar cover Proper handling of the chain saw will reduce the likelihood of accidental contact with the moving saw chain Follow instructions for lubricating chain tensioning and changing accessories Improperly tensioned or lubricated chain may either break or increase the chance for kickback Keep handles dry clean and free from oil and grease Greasy oily handles are slippery causing loss of control gt Original instructions Cut wood only Do not use chainsaw for purposes not intended For example do not use the chainsaw for cutting plastic masonry or non wood building materi als Use of the chainsaw for operations different than intended could result in a hazardous situation Causes and operator prevention of kickback Kickback may occur when the nose or tip of the guide bar touches an object or when the wood closes in and pinches the saw chain in the cut Tip contact in some cases may cause a sudden reverse reac tion kicking the guide bar up and back towards the operator Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator Either of these reactions may cause you to lose control of
22. t the chainsaw make sure the saw chain is not contacting anything A moment of inattention while operating chain saws may cause entanglement of your clothing or body with the chain saw Always hold the chainsaw with your right hand on the rear handle and your left hand on the front handle Holding the chainsaw with a reversed hand configuration increases the risk of personal injury and should never be done Hold the power tool by insulated gripping surfaces only because the saw chain may contact hidden wiring Saw chains contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock Wear safety glasses and hearing protection Further protective equipment for head hands legs and feet is recommended Adequate protective clothing will reduce personal injury by flying debris or accidental contact with the saw chain Do not operate a chainsaw in a tree Operation of a chainsaw while up in a tree may result in personal injury Always keep proper footing and operate the chain saw only when standing on fixed secure and level surface Slippery or unstable surfaces such as ladders may cause a loss of balance or control of the chainsaw When cutting a limb that is under tension be alert for spring back When the tension in the wood fibres is released the spring loaded limb may strike the operator and or throw the chain saw out of control Use extreme caution when cutting brush and sa
23. tion Separate collection This product must not be disposed of with normal household waste Separate collection of used products and packaging allows materials to be recycled and used again Re use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials Ma 7 In gt A are Local regulations may provide for separate collection of elec trical products from the household at municipal waste sites or by the retailer when you purchase a new product Black amp Decker provides a facility for the collection and recycling of Black amp Decker products once they have reached the end of their working life To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf You can check the location of your nearest authorised repair agent by contacting your local Black amp Decker office at the address indicated in this manual Alternatively a list of authorised Black amp Decker repair agents and full details of our after sales service and contacts are available on the Internet at www 2helpU com Technical data Voltage Bar length Max bar length Chain speed No load mlsm Max cutting length Oil capacity Weight Voltage Capacity Type Input Voltage 400 240 Output Voltage 8 20 Current 400 Approx charge time h Level of sound pressure according to EN 60745 LA sound pressur
24. www blackanddecker com au www blackanddecker co nz Y Y UY LU ma GKC1825L N A sA Wi f W v vi Yu Y AA WQ YW Ay Sh a ya WAY Ye en a ho y AN US W W N Y A t 1 ieh Ww SA Y MA Mr LN yin y aw V Wi i Nu a MT y yf SS VY W W 16 YA Ku A N Wi aye W UN wey y V i 2 f va V y gt Original instructions Intended use f If operating a power tool in a damp location is Your BLACK DECKER chainsaw has been designed for unavoidable use a residual current device RCD pruning and felling trees and cutting logs This tool is intended protected supply Use of an RCD reduces the risk of for consumer use only electric shock 3 Personal safety Safety instructions a Stay alert watch what you are doing and use common sense when operating a power tool Do not use a General power tool safety warnings power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention A Warning Read all safety warnings and all while operating power tools may result in serious personal
25. y the original Original instructions ENGLISH 4 battery is defective and should be returned to a service centre for recycling If the new battery gives the same indication as the original battery take the charger to be tested at an authorised services centre Note It may take as long as 30 minutes to determine that the battery is defective If the battery is too hot or too cold the charging indicator will alternately blink red fast and slow one flash at each speed and repeat Filling the oil reservoir fig O Remove the oil cap 3 and fill the reservoir with the recommended chain oil You can see the oil level in the oil level indicator 11 Refit the oil cap 3 Periodically switch off and check the oil level indicator 11 if it is less than a quarter full remove the battery from the chainsaw and refill with the correct oil Oiling the chain We recommend that you use only Black 8 Decker oil A6027 50 during the lifetime of your chainsaw because mixtures of different oils could lead to the oil becoming degraded which can drastically shorten the lifetime of the saw chain and create additional risks It is normal for a small amount of excess oil drip from the chain saw bar and chain during storage Do not store chain saw on top of any thing that may be damaged by the dripping oil Never use waste oil thick oil or very thin sewing machine oil These may damage your chainsaw The saw chain 6 must be
Download Pdf Manuals
Related Search