important product information
Contents
1. in firmware releases 9 0 and later Important Product Information GFK 1512E 1C693CPU360 BC Data CPU Type Single slot CPU module Total Baseplates per System 8 CPU baseplate 7 expansion and or remote Load Required from Power Supply 670 milliamps from 5 VDC supply Processor Speed 25 MegaHertz Processor Type 80386EX Typical Scan Rate 22 milliseconds per 1K of logic Boolean contacts User Program Memory maximum 240K 245 760 Bytes Note Actual size of available user program memory depends on the amounts configured for the R AI and WAQ configurable word memory types described below Discrete Input Points I 2 048 Discrete Output Points Q 2 048 Discrete Global Memory G 1 280 bits Internal Coils M 4 096 bits Output Temporary Coils T 256 bits System Status References S 128 bits S SA SB SC 32 bits each Register Memory R Configurable in 128 word increments from 128 to 16 384 words with DOS programmer and from 128 to 32 640 words with Windows programmer Ver 2 2 or VersaPro version 1 0 Analog Inputs AI Configurable in 128 word increments from 128 to 8 192 words with DOS programmer and from 128 to 32 640 words with Windows programmer Ver 2 2 or VersaPro version 1 0 Analog Outputs AQ Configurable in 128 word increments from 128 to 8 192 words with DOS programmer and from 128 to 32 640 words with Windows programmer Ver 2 2 or VersaPro version 1 0 Sy2. your PLC programming software The SNP ID must be set separately using the programming software or the Hand Held Programmer HHP Firmware Upgrade Hardware Requirements Note The Model 35x and 36x CPU operating firmware is stored in FLASH memory The firmware upgrade is provided on a floppy disk and must be serially downloaded from a Personal Computer An IBM AT personal computer or better PC with a minimum 640K of RAM one 3 5 floppy drive MS DOS version 3 3 or later or Windows 95 or later a hard drive and one RS 232 serial port is required In addition a serial cable is required The following serial cable kit is available from GE Fanuc IC690ACC901 Mini Converter Kit with cable RS 232 RS 485 Optionally the cable can be assembled from the following parts IC690ACC900 RS 232 to RS 485 422 Converter Unit IC693CBL303 15 Pin RS 485 Serial Cable IC690CBL705 25 Pin RS 232 Serial Cable IC690CBL702 9 Pin RS 232 Serial Cable Only one of these cables is required Selection depends on PC Serial Port Connector Option Module Revision Requirements e Ethernet Interface Module Compatibility All IC693 Ethernet Interface IC693CMM321 modules used with these CPUs should be updated to IC693CMM321 firmware release 1 10 or later This is also a requirement of the TCP IP Ethernet version of the MS DOS programming software During a Run Mode Store Alt S hot key combination of a large program block greater than 14 kilobytes the Ether
3. 0 33A1 IC693CPU360 BD Main R9 10 22A1 emer wman S Functional Compatibility e The Windows PLC Programming Software version 2 00 or later or VersaPro software version 1 0 or later must be used to take advantage of C programming or Sequential Function Chart SFC subroutines e Version 4 00 or later of the C toolkit must be used for C programming e The MS DOS PLC Programming Software Version 9 02 or later must be used to take advantage of the new features introduced in firmware release 9 00 These new features are listed in the section New Features and Functionality of Firmware Release 9 00 Operating Notes Important Product Information 3 GFK 1512E Operating Notes User Flash Contents User information consisting of program configuration CPU ID used for SNP communications and status tables in RAM memory will automatically be cleared if the CPU firmware in flash memory is changed You will need to restore these if upgrading firmware A recommended procedure is to first back up your user information from RAM memory to Flash memory Then write your new firmware to Flash memory firmware is stored in a different location in Flash memory than that used for storing user information such as program configuration etc Finally write your user information back out of Flash into RAM memory As an alternative your user information program configuration etc can be restored from a computer based backup program folder using
4. July 8 1999 GFK 1512E IMPORTANT PRODUCT INFORMATION READ THIS INFORMATION FIRST Product 1C693 CPU Modules with Firmware Release 9 10 IC693CPU350 BD IC693CPU360 BD Introduction This document contains information that is not available in any other publication therefore we recommend you save it for future reference This document discusses the features of the newly released firmware version 9 10 for CPU modules IC693CPU350 and IC693CPU360 This version resolves the problems listed on page 4 Feature Highlights The following features were introduced in release 9 00 Software Floating Point The CPU350 and CPU360 support all of the floating point function blocks that are currently supported by the CPU352 They are implemented in firmware using floating point emulation These Floating Point math function blocks are described in the IC693 PLC Reference Manual CPU360 user memory increased to 240K bytes R AI and AQ references are configurable up to 16K of R 8K of AI and 8K of WAQ memory using the MS DOS PLC programming software version 9 02 These three references are configurable up to 32K version 2 2 of the Windows PLC programming software and version 1 0 of the VersaPro programming software Configuration instructions for this feature are described in the MS DOS IC693 Programming Software User s Manual and are included in on line help in both Windows PLC programming software packages Note that the CPU350 does not suppor
5. Problems Resolved in Firmware Version 9 01 SNP Master mode on CPU Ports With some very large configurations and version 9 00 firmware after a power cycle CPU ports set up for SNP Master would need to have their configuration re stored for the protocol to accept COMM_REQs This is corrected in version 9 01 Online Changes to Reference Tables Making online changes with the programmer to reference tables could result in a watchdog timeout This has been corrected in version 9 01 350 and 360 9 00 Upgrade After upgrading to version 9 00 on a 350 or 360 PLC the user flash area would need to be written to or cleared afterwards with an HHP DOS or Windows programmer Otherwise the RAM contents would be cleared on a power cycle This is no longer necessary when upgrading to 9 01 Read from Flash In version 9 00 reading a folder from flash memory could result in the PLC going into a faulted state This is corrected in version 9 01 Important Product Information 5 GFK 1512E Restrictions and Open Problems Timing Issue With ALG220 221 Modules May Result in Incorrect Al Values Read by CPU A problem was found with the IC693ALG220 221 where the actual AI values reported by the card may exhibit erratic behavior catalog module revisions F and earlier may show this problem revision G has fixed this problem Certain current or voltage levels within the input range applied to the card could cause the AI values to report incorrectly The prob
6. lem stems from the use of particular optocouplers which may exhibit timing issues with these CPU35x 36x modules CPUs 341 331 321 313 and 311 have not exhibited this timing problem reading AI values Documentation Instructions for using these two modules can be found in the latest version of the following manuals General Configuration Instructions C693 PLC Programming Software User s Manual Ladder Logic Programming C693 PLC Reference Manual Installation Instructions C693 PLC Installation Manual firmware 9 0 features will be added to revision P of this manual 6 Important Product Information GFK 1512E 1C693CPU350 BC Data CPU Type Single slot CPU module Oor CPU 350 ON Processor Speed 25 MegaHertz Processor Type 80386EX Typical Scan Rate 22 milliseconds per 1K of logic Boolean contacts User Program Memory maximum 32K Bytes not configurable Discrete Input Points I 2 048 Discrete Output Points Q 2 048 Output Temporary Coils T 256 bits Analog Outputs AQ 512 words System Registers for reference table 28 words SR viewing only cannot be referenced in user logic program gt 2 000 Shift Registers Built in Serial Port s 1 uses connector on PLC power supply Supports SNP SNP X protocols Requires CMM module for CCM or RTU protocol support Profibus GBC GCM and GCM option modules Override ate Bake Gas fg Floating Point Math Support Yes firmware based
7. net module may time out causing communications to fail Changing the Communications Window to Run to Completion mode or storing the program in Stop mode will allow the store to take place successfully e FBC Compatibility FBC version 3 or later is required for these CPUs Writing to Flash Using the Windows PLC Programming Software When writing very large programs to flash memory it may be necessary to increase the Windows PLC programming software request timeout value to avoid receiving a request timeout message An upper bound of 25 seconds is typically satisfactory 4 Important Product Information GFK 1512E Problems Resolved in Firmware Version 9 10 Al amp AQ Above Default Values Release 9 00 provided support for configuring AI and AQ above their default values These new references would previously only work as extra program memory and could not be used as actual inputs or outputs on physical modules in the configuration This has been corrected in release 9 10 so that these higher references will now work the same as the lower references Load File of Size 1528 Bytes Loads of a user program where the file was of this specific size would fail This has been corrected in release 9 10 C Program with Code Area Greater Than 64K Bytes Before release 9 10 C Program blocks with code areas greater than 64k bytes would not store In release 9 10 and later C program blocks code sizes are limited only by available memory
8. stem Registers for reference table 28 words SR viewing only cannot be referenced in user logic program gt 2 000 Shift Registers Yes Built in Serial Port s 1 uses connector on PLC power supply Supports SNP SNP X protocols Requires CMM module for CCM or RTU protocol support Communications LAN Supports multidrop Also supports Ethernet FIP Profibus GBC GCM and GCM option modules Override Yes Battery Backed Clock Yes Interrupts Supports the periodic subroutine feature Type of Memory Storage RAM and Flash PCM CCM Compatibility Yes Floating Point Math Support Yes firmware based in firmware release 9 0 and later CPU 360 ON
9. t configurable user memory Its user memory is set at a fixed value of 32K bytes Sequential Event Recorder The Sequential Event Recorder function block can be used to record up to 1024 samples of 32 individual discrete bit references Both of these CPUs support this function block Instructions on programming the Sequential Event Recorder are found in the C693 PLC Reference Manual Break free SNP The SNP protocol no longer requires a break to operate This allows SNP to work over a wider variety of modems Hardware Identification The following table shows the revision level of the circuit boards used in the current version of these CPUs CPU Catalog Circuit Board ID Circuit Board Version Number 1C693CPU350 BD 44A739579 G01R04 or later 1C693CPU360 BD 44 4739579 GO1R04 or later MS DOS and Windows are registered trademarks of Microsoft Corporation 2 Important Product Information GFK 1512E Firmware Upgrade Kits If you wish to upgrade an existing CPU350 or CPU360 to firmware version 9 10 you may purchase the applicable kit identified in the following table All previous versions are capable of being upgraded Firmware 9 10 Upgrade Kit Catalog Number CPU Catalog Number Firmware Upgrade Kit Catalog Number IC693CPU350 all versions 44A747145 G03 IC693CPU360 all versions 44A747148 G03 Firmware Identification Moth Daught CPU Catalog Number a srboard pes create Firmware Version Firmware Version Boot R9 0
Download Pdf Manuals
Related Search