USER MANUAL - Tanning Bed Parts
Contents
1. 6 7 8 9 10 14 and 15 See your T Max manual for descrip tions of these parameters and how they func tion T Max Manager Remote System This system is ideal for multiple sunbed instal lations Simply connect the RJ 22 modular cable s described in the T Max Manager manual into the remote port s located on the back of your sunbed and follow the instruc tions that came with your remote system noting figure 1 If you have an older T Max Manager that does n t support auto addressing set the address or id of each sunbed manually as described in Setting the address manually You can place your sunbed at any location in the series NOTE A T Max 1A can be substituted for the 3A in figure 1 Installation Remote Connections T Max 1A and 3A Remote Systems The T Max 1A and 3A offer the same control as the T Max Manager in single sunbed instal lations If you re using a 1A it must have a chip labelled master installed on its circuit board The remote control bypass plug must not be used in this configuration After you have set the T Max 1A5 or 3A5 address to 0 refer to your T Max user s guide and the sunbed s address to 1 see right simply connect the RJ 22 modular cables described in the T Max user s guide directly into either port located on the back of the sunbed and either port on the back of the T Max 1A or 3A See figure 2 figu2. the installed timer software version a factory set timer code and then the sunbed s id number 25 VCO ELLET 23713 024 Problem My bed is connected to a T Max remote system but am having trouble getting into id mode When auto addressing the first bed does not register an id My bed won t work with the T Max Manager remote system Timer display changes to indicate a tanning time after the timer but ton is pressed but lamps do not come on My bed is connected to the T Max Manager remote system and when the delay time has expired the timer display starts counting down but the bed lights do not come on My bed connected to a T Max Manager did not display dL but does indicate o a tanning time and the lamps have come on a tanning time but the lamps have not come on Solution You have probably attempted to connect your sunbed to the remote system already Disconnect the remote plug s from the ports at the back of the sunbed wait 90 seconds and try again When using the auto address feature of the T Max Manager you must wait 10 seconds from the time you start the auto address function before addressing the first bed The sunbed must first be set to a unique address see Remote Connections The bypass or terminator plug may be installed in the series in an inappropriate location Plug the bypass plug only into the bed at the end of the series Bypass plug is
3. 3 8 16 x 1 1 4 Hex Socket Bolt Ouantity 18 Access Panel Key 3 8 16 Self locking Quantity 1 Nan Hex Nut Quantity 18 Control Cord Quantity 1 Installation Assembly Procedures Assembly Procedures Before installing the bench endcaps you must install the body fan power cord into the foot end endcap as shown below and the shoulder tanning unit power cord into the head end endcap The connector will snap securely into the endcap Snap body fan power cord into hole in foot end endcap BODY FAN POWER CORD Foot end endcap shown 5 VCO ELLET 23713 024 Installation Assembly Procedures Parts needed Foot end endcap Head end endcap 14 10 x 1 Phillips pan head screws 4 10 x 1 2 Phillips pan head screws Attach endcap with 1 screws as shown Foot end endcap shown P Installation Assembly Procedures Parts needed Canopy 2 Canopy Adapter Arms 4 Adapter Gussets 12 3 8 x 1 1 4 hex socket bolts 12 3 8 self locking hex nuts CANOPY ARM Attach adapter arms to canopy arms using two adapter gussets and six bolts and nuts ADAPTER GUSSET ADAPTER ARM VCO ELLET 23713 024 Installation Assembly Procedures Parts needed 6 3 8 x 1 1 4 hex socket bolts 6 3 8 self locking hex nuts CANOPY 1 Install this bolt as a fa positioning aide 2 p Slip can
4. We recommend connection by a professional electri cian IMPORTANT Voltage must be below 230V AC or may require a Buck Booster Use of a voltage source above 230V AC may reduce the life of some components in your sunbed The Solar System 52 Platimum Speed System requires a dedicat ed circuit capable of providing 50 Amp service This unit must be hard wired directly to a junction box should observe the following consid Make sure the room in which you intend to use your sunbed is well ventilated Air from the room is used to cool the sunbed and a poorly ventilated room may cause the unit to become hot and cause discomfort to the user Your sunbed is designed to operate in an ambient room temperature of 80 F maximum and 70 relative humidity Place your sunbed no closer than 6 from any wall Make sure that cur tains drapes and other room furni ture do not obstruct the airflow into or out of the fan opening areas Proper assembly of your sunbed requires three people Plan to have a couple of helpers assist you VCO ELLET 23713 024 Installation Hardware Inventor Hardware Inventory Canopy Adapter Arm O Open the hardware bags and remove the o Quantity 2 hardware Make sure you have the follow o o ing hardware items o o 10 x 1 Phillips Pan Head Screw Adapter Gusset Ouantity 14 Ouantity 4 10 x 1 2 Phillips Pan Head Screw Safety Goggles Ouantity 12 Ouantity 1
5. be on have service technician check the contactor and its wiring from the main timer box Units with separate bench contactor only Timer display is indicating Er 5 Not currently used Timer display is indicating Er 6 Not currently used Timer display is indicating Er 7 Face Tanner contactor is closed when it should be open have service technician check the contactor Timer display is indicating Er 8 Face Tanner contactor is open when it should be closed have service technician check the contactor and its wiring from the main timer box Timer display is indicating Er 9 Ballast Drawer is open or drawer switch is broken Timer display is indicating Er 10 Timer computer is in an illegal state reset power to correct replace main timer if error reoccurs Timer display is indicating Er 11 Timer computer is in an illegal state reset power to correct replace main timer if error reoccurs Timer display is indicating Er 12 Timer computer is in an illegal state reset power to correct replace main timer if error reoccurs 27 VCO ELLET 23713 024 Problem Timer display is indicating Er 13 Timer display is indicating Er 14 Timer display is indicating Er 15 Solution Timer computer is in an illegal state reset power to correct replace main timer if error reoccurs The timer display is not responding Check cable to display Replace display assembly Replace main timer box Timer computer is in an illegal stat
6. 278 2900 This sunbed utilizes a proprietary system of components known as the Speed System Only certified Speed System components may be used as replacements including lamps and ballasts Record this information for ease of service Date of purchase Bench serial number Canopy serial number Ballast tray ID number
7. Platinum Solar System 52 USER MANUAL Limited Lifetime Warranty Your tanning unit is warranted to be free of structural defects in its material and workman ship under normal use for its lifetime It will be repaired or replaced at the discretion of the manufacturer if any defect to the structure which affects the performance of the unit is found For 6 months from the date of purchase replacements for parts that prove to be defective in material or workmanship will be provided Acrylic shields fluorescent lamps and lamp starters are excluded from this warranty Labor will be covered for 30 days from purchase date Normal wear damage from misuse or abuse damage incurred in transit or damage done by unauthorized repairs or modifications are not covered by this warranty ETS Inc disclaims any implied warranty of merchantability or fitness for any period beyond the expressed warranty Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you No one has authority to change or modify this Limited Lifetime Warranty in any respect To obtain service under the Limited Lifetime Warranty contact ETS Inc at 1 800 449 3605 and ask for the Technical Service Department ETS Inc shall not be liable for loss of use loss of time inconvenience rental or substitute products loss of business loss of income or any other incidental or consequential damages Some st
8. are and Maintenance Cleaning After Use Step 2 With a soft cloth wipe the entire length of each lamp to remove Clean and disinfect your tanning bed s any film buildup bench canopy and rear lamp module after Step3 Clean both sides of the acrylic each use Use a non abrasive disinfectant shields with a non ammonia dis cleaner that does not contain ammonia or infectant cleaner ammonia derivatives Ammonia may dam Step 4 Wipe the reflectors with a clean age the acrylic shield Spray the acrylic damp cloth lightly with disinfectant and wipe dry with a Step 5 Reinstall the lamps and acrylic clean soft cloth We recommend SunQuest shields disinfectant and SunQuest acrylic cleaner Step 6 Clean or replace air filters on top of ballast tray and under bench see Final Adjustments Replace with 10 x 24 x 1 furnace filters Thorough Periodic Cleaning Introduction The cooling fans draw air through the bed and over time will cause a dust buildup on the lamps and reflectors This will reduce the tanning effectiveness of the bed When a dust buildup is observed it is necessary to thoroughly clean the inside of the bench canopy and rear lamp module Mechanical Inspection Your tanning bed has been built for years of service To ensure trouble free operation throughout its life inspect the units mechanical integrity every 400 500 hours of use e Inspect the units fasteners verifying WARNING that all are firmly in plac
9. ates do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which may vary from state to state All warranty service must be performed by an authorized service person If your tanning unit must be returned for service all freight charges must be at your expense Contact your place of purchase for the address of the service center nearest you Proof of purchase is required to obtain warranty service This warranty covers the original purchaser only This warranty is void if the unit is modi fied in any manner from its original design VCO ELLET 23713 024 eicome Congratulations on your purchase of this technologically advanced sun tanning unit It has been designed to provide years of dependable service for you Please read all the instructions in this booklet before installing and using the unit Always be sure to observe all safety precautions Contents Safety Information iii installation sss ass anses ice EEVEE 1 Unpacking and Inspection 1 Tools Required ceii perii ee Pid ed dd Cees Me PEG dad 2 Pre Installation Planning 3 Hardware INVentory 4 0 0 dan need ede dae nk ee wey 4 Assembly Procedures sa sagas pad div aa ak ae a ep boa 5 El ctri
10. cal Connections usa guns ss K ee ae ee 12 Final Adjustments 4 444 35454440 ces es sas numa des 13 Remote ConnectOns 22534244 ek f area ee Sa RESO 14 Operation casam av esse mg iss eos eee ae Gus Ko dos ed 17 Before You TA a sua dade cas nu osov a dit dade none 17 EXPOSURE TIMES serce pei naman bee ay e ARE DO aa si 17 Using Your Sunbed uses nas ua Pa OES ee ee kn 18 Care and Maintenance s s 66 sb nan est arts end as sees nade 20 Cleaning After Use saa ed bead qu nd ad A n anda 20 Thorough Periodic Cleaning 20 Mechanical Inspection 20 Lamp and Acrylic Replacement 21 Troubleshooting 25 Safety Information LABELING NOTICE Labels are affixed on all systems to inform the user of possible dangers Regulations are stated in 21 CFR Section 1040 20 and require that all products manufactured after September 8 1986 which use sunlamps must display the following DANGE Ultraviolet radiation Follow instructions Avoid overexposure As with natural sunlight overexposure can cause eye and skin injury and allergic reactions Repeated exposure may cause premature aging of the skin and skin cancer WEAR PROTECTIVE EYEWEAR FAILURE TO MAY RESULT IN SEVERE BURNS OR LONGTERM INJURY TO THE EYES Medications or cosmetics may increase your sensitivity to the ultraviolet radiation Consult physician before using sunlamp i
11. cuit breaker or replace fuse The last minute of tanning time If the timer button has been pressed to decrease tanning time does not count down from 59 sec during the session the time expired in the current minute is onds but some time less than 59 subtracted from the last minute seconds One or more lamps fail to light Check that lamp is installed correctly Switch unlit lamp with a lamp that lights if new lamp lights and old lamp still does not replace old lamp The face tanners will not Face tanner operation is initially delayed by 5 seconds come on Face tanners will not relight until cooled Replace face tanner lamp see Removing Replacing Face Tanner Lamps on Face Tanner Models The canopy will not stay up Your sunbed uses a smooth gliding spring lift system to raise The canopy will not stay down the canopy This lift system may need to be adjusted slightly from time to time See Final Adjustments for proper adjust ment procedures The canopy should raise easily as well as rest fully closed My canopy opens and closes too Your sunbed utilizes a damper which limits the canopy s fast slamming not enough resis movement speed This also serves as a safety device in case of tance spring lift failure as the canopy will not crash down Replace the damper on back of unit forgot what address or id set By holding the body fan button for 3 seconds the timer display my sunbed to will briefly display three numbers
12. e e Inspect lift adjustment Adjust for prop oke hazard er lift if needed See Final Adjustments Disconnect power before performing this procedure e Inspect the AC power cord and its connections Cleaning the Canopy and Bench e Inspect the acrylic Broken cracked or badly scratched acrylics should be Step 1 Remove the acrylic shields and P immediately replaced lamps as described in Lamp and Acrylic Replacement 20 Lamp and Acrylic Replacement Introduction To be assured of maximum tanning effec tiveness change lamps after approximate ly 800 1000 hours of use Tanning will continue after this time but at a slower rate To ensure trouble free operation of your sunbed replace the lamp starters whenever the lamps are replaced WARNING Shock hazard Disconnect power before servicing Maintenance Height Feature The Solar System 52 offers a convenience feature when maintenance must be per formed Behind the front access panel is a release handle see Final Adjustments With the canopy open pull this handle and raise the canopy to its maintenance position allowing easier access to lamps etc When finished simply close the canopy to return to normal operation Opening Replacing Acrylic Shields The acrylic shield in the bench is secured in place by a plastic profile across the front ledge of the bench Simply pry up on 21 Care and Maintenance Lamp and Acrylic Replacement the in
13. e reset power to correct replace main timer if error reoccurs 28 Notes 23713 024 29 Notes 30 VIO EILEZ 23713 024 O zo WZ en LI DE gt aa Yi E Sa OU jt us Z gt QI mt Ze Si Z gt FA aa SA Tr lt W TS Su a Oq ss Zo EA Ww SY FAN SQUARE ACCESS BENCH PANEL FRONT PROFILE LAMP HOLDER STARTER HOLDER W STARTER Z Le qu x LH gt ZU a I LI O o ada zo zo W Z uz QE m LL 5 5 at DL z z LL LU 23713 02A Shoulder Tanner ENDCAP REAR LAMP MODULE HEAD END FAN SQUARE GI IA LAMP HOLDER gt Z K fi eu AA 9 y LA p A Zm 9 BALLAST 80W SHOULDER TANNER Ballast Tray CAPACITOR RELAY BED FANS CONTACTOR RELAY CANOPY BALLAST 400W FACE TANNER CONTACTOR RELAY BENCH RELAY SHOULDER TANNER iS ra zi LU lt L O za Zur Ea or ogon nF lt z LytZ A T E rlz 45 on ZT Sw O F A O a xE o TIMER FAN SQUARE VCO ELLET 23713 024 Parts List This is a list of parts which may be replaced by the consumer Care should be taken when replacing anything related to electrical wiring We recom mend contacting a professional electrician When calling for parts first state your bed model then refer to this list and preceding illustrations for proper part identification Access Panel Access Panel Key Acrylic Bench w
14. e bronzage commence normalement appara tre apr s les premi res s ances il atteint son apog e au bout d environ quatre semaines Les personnes qui ont d j un teint h l peuvent commencer des niveaux plus lev s selon l importance de leur h le initial TEMPS D EXPOSITION RECOMMAND EN MINUTES LE TEMPS D EXPOSITION MAXIMAL EST DE 12 MINUTES lev 1 Semaine 1 give m k Type de peau 18 38 Eleve 2 Elev 3 Elev 4 Sem suivantes Temps maximal Peau sensible br le facilement et ne bronze pas NON RECOMMAND II Peau claire br le facilement et bronze tr s peu Il Peau normale br le et bronze de fa on mod r e IV Peaufonc e br le tr s peu bronze plus facilement que la moyenne Les lampes neuves mettent approximativement 10 de plus de rayons ultraviolets au cours des 50 premi res heures de fonction nement Le temps de bronzage doit donc atre r duit d rquote environ 10 pendant cette p riode AVERTISSEMENT Lisez le livret d instructions avant d utiliser cette lampe solaire Les autres personnes pr sentes dans la pi ce doivent aussi porter des lunettes protectrices lorsque les lampes sont allum es Coquilles de protection pour les yeux recommand es Les coquilles de protection fournies Lucas Products Super Sunnies ou Intrexco n 5635 1 ou l quivalent tel que le stipule le doc ument 21 CFR 1040 20 Les autres types de lunettes protectrices peuvent ne pas assurer une protection ad quate Util
15. e interface kit is required Contact ETS to obtain the kit Figure 3 details a typical connection Follow the instructions provided with the kit and from the remote s manual to make the necessary connections Non T Max Remote System Remote Interface Kit figure 3 Installation Remote Connections Operation Before You Tan Before using your sunbed please note the following important precautions e Your skin should be free of cosmetics oils or other body lotions prior to tan ning except those specifically made for use with tanning devices However do not remove natural body oils by bathing or showering immedi ately before tanning e Your hair should be free of gels mousses sprays or other hair products prior to tanning These products can cause damage to the sunbed acrylic As an alternative a shower cap or towel may be worn to keep treated hair away from the sunbed surfaces e As with all electrical appliances do not operate this device near water or while you are wet RECOMMENDED EXPOSURE TIMES IN MINUTES Level 1 Week 1 1st 3rd Sessions Skin Type I Sensitive Skin Burns easily and severely and does not tan e Some medication may increase your sensitivity to ultraviolet light It is rec ommended that you consult a physi cian before using this sunbed if taking any medication or if you suspect that your skin might be especially sensitive to sunlight Included with this manual is an FDA boo
16. f you are using medications or have a history of skin problems or believe yourself especially sensitive to sunlight If you do not tan in the sun you are unlikely to tan from the use of this product Children the elderly or fair skinned people who always burn easily and either never tan or tan minimally should not use this equipment To use lie down under canopy and pull down as far as adjustment will allow maintaining minimum distances between your body and canopy clear plastic panels as illustrated below otherwise overexposure may occur Do not use without clear plastic panels in place Untanned persons should not tan on consecutive days during their first week of tanning Never tan more than once a day Tanning normally appears after the first few sessions and maximizes after approximately four weeks Tan once or twice per week thereafter to maintain appearance Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan RECOMMENDED EXPOSURE TIMES IN MINUTES MAXIMUM EXPOSURE TIME IS 12 MINUTES Level 1 Week 1 Subsequent Level 2 Level 3 Level 4 Skin Type 1st 3rd Sessions Maximum I Sensitive Skin Burns easily and severely and does not tan NOT RECOMMENDED FOR TANNING II Light Burns easily and severely and tans minimally HI Normal Burns moderately and tans average IV Dark Burns minimally tans easily and above average New lamps emit approximately 10 more ultraviolet radiation d
17. ff during use Units eguipped with face tanner only Shoulder tanner control Turns shoul der lamps on and off during use Units equipped with shoulder tanner only Body fan control Controls the speed of the body fan during use Body fan speed indicator Indicates speed of fan OFF LOW MED HIGH Timer display Disp ays remaining time Stop button Stops tanning session Timer button Turns bed on Timer dis play shows remaining time If a lesser time is desired press timer button until desired time is displayed Lift the canopy lie down on the bench face up lower the canopy toward your body using the canopy handle For best results position the canopy as close to your body as possible Put on your safety goggles Press the timer button G to begin the tan ning session The lamps will turn on and the timer will begin to count down If a tanning time less than the displayed time is desired repeatedly press the timer button G to decrease the remaining time When the timer reaches O the lamps turn off If you want to stop your session before time expires press the stop button F You will have ten seconds to restart with the remaining time otherwise the timer will reset to 0 Raise the canopy by using the canopy handle do not push up on the acrylic shield The cooling fans run for three min utes after the lamps shut off to aid in cool ing the sunbed VCO ELLET 23713 024 C
18. he ballast tray is secured to the carton bottom with brackets Remove these brackets from the ballast tray with a Phillips screwdriver Note The cartons are reusable if you want to move the unit or in the unlikely event that you may find it necessary to return your sunbed After unpacking the unit check to make sure you have received the following e Canopy unit e Bench unit e Rear lamp module e Ballast tray e Contoured access panel with decal e Two large bench endcaps e Body fan kit e Shoulder tanner kit e Two bags containing necessary assembly hardware safety goggles and pillow Inspect these items including the canopy and bench to make sure they are free from any visible damage Report the extent of any damage to the transportation company Record the serial numbers of the canopy and bench and the ballast tray ID number in the area provided at the back of this manual This information will be required whenever you call customer service VCO ELLET 23713 024 Installation Tools Required Tools Required You will need the following tools to assemble your sunbed L 2 Phillips Screwdriver Adjustable Wrench a 5 16 and 1 4 Allen Wrenches Installation Pre Installation Plannin Pre Installation Planning Before you begin to assemble your sunbed you erations Your sunbed operates from a 220V AC power source The unit should be wired to a dedicated circuit as described below
19. ing time Stop button Interrupts tanning session Timer button Turns bed on Timer dis play shows remaining time If a lesser time is desired press timer button until desired time is displayed Lift canopy lie down on bench face up lower canopy toward your body using canopy handle For best results position canopy as close to your body as possible Put on your safety goggles 3 Assuming the remote system has been set to allow a pre tanning delay time the timer display E will repeatedly flash the delay symbol dL and then the remaining delay time Press the timer button G or wait until the delay time has expired to begin the tanning session The lamps will turn on and the timer will begin to count down When the timer reaches O the lamps turn off If you want to interrupt your session before time expires press the stop button F Raise the canopy by using the canopy handle do not push up on the acrylic shield The cooling fans run for three min utes after the lamps shut off to aid in cool ing the sunbed The timer will indicate as a reminder to clean the sunbed After the sunbed is cleaned press the timer but ton and the display will return to 0 16 Operation Using Your Sunbed Using Your Sunbed When used as a stand alone unit or when connected to a remote system using a control relay S eh A B C D E F G Face tanner control Turns face tanners on and o
20. is sans lunettes protectrices ce produit peut causer des br lures ou l sions oculaires graves Si vous souffrez d un malaise arr tez l utilisation et con sultez un m decin SEULES LES LAMPES SUIVANTES ONT T HOMOLOGU ES POUR CET QUIPEMENT SPEED 225R Wolff Mod le SPD71 T12 225R Bi Pin O SPEED 255R Wolff Mod le SPD71 T12 255R Bi Pin Philips Mod le HPA 400 30s ou CosmoTech Mod le 23045 ou 20046 unit faciale COSMOLUX RA plus 15504 40W unit en bandouli re 6 3 3 D branchez le cordon d alimentation avant de nettoyer l appareil d en faire db x l entretien ou de changer les lampes Cet quipement doit tre mis la terre Ce produit est conforme aux normes de rendement pour les lampes solaires dans le document 21 CFR partie 1040 20 di Installation Unpacking and Inspection Your sunbed comes in two cardboard car tons one for the canopy and one for the bench and ballast tray Open the cartons and remove the sunbed parts as follows The boxes that your sunbed come in dis mantle to allow easy removal of the units Remove the box tops and pull the sides out The bench and canopy are each wrapped in plastic Remove the plastic and with a helper grasp the canopy and pull it from the carton bottom Do the same for the bench Do not attempt to lift either unit with the plastic still on as it may slip The black endcaps on the canopy should not be used to lift the unit T
21. ith aluminum frame Acrylic Canopy with aluminum frame Acrylic Rear Lamp Module Acrylic Shoulder Tanner Ballast SPEED TM system Ballast 80W shoulder tanner lamps Ballast 400W face tanner lamps Capacitor 75uF Contactor Relay Control Cord Cover Canopy Damper Endcap Bench Foot End Endcap Bench Head End Endcap Canopy Foot End Endcap Canopy Head End Endcap Rear Lamp Module Foot End Endcap Rear Lamp Module Head End Fan Round Fan Square Filter Handle Kit Hardware Kit Main Hardware Kit Canopy Hour Counter Ignitor Lamp Holder w Starter bench and shoulder tanner lamps Lamp Holder w o Starter bench and shoulder tanner lamps Lamp Holder Tall canopy and rear lamps Lamp Holder Short canopy and rear lamps Lamp Holder Face Tanner Lamps Manual Panel Left Pedestal Front Panel Right Pedestal Front Pillow Profile Bench Front with warnings Profile Canopy Front Profile Canopy Rear Relay Remote Connection PCB Remote Control Bypass Plug Schematic Packet Starter K 12 main lamps Starter Holder main lamps Support Bench Acrylic kickstand Thermostat for face tanner Timer Timer Keypad Kit circuit board Timer Keypad Pushbuttons Wiring Harness Keypad Remote Interface Wiring Harness Resistor Code Wiring Harness Timer in Tray Not shown CALL FOR SERVICE OR QUESTIONS 1 800 449 3605 SFS 6270 Corporate Drive Indianapolis IN 46
22. klet on medications that increase sensitivity to light Exposure Times Follow the guidelines for skin type and exposure times as shown in the table below Untanned persons should not tan on consecutive days during their first week of tanning Never tan more than once a day Tanning normally appears after the first few sessions and maximizes after approxi mately four weeks Tan once or twice per week thereafter to maintain appearance Persons already having a base tan may begin at advanced levels corresponding to the extent of their base tan MAXIMUM EXPOSURE TIME IS 12 MINUTES Subsequent Level 4 Maximum Level 2 Level 3 NOT RECOMMENDED FOR TANNING II Light Burns easily and severely and tans minimally 10 12 III Normal IV Dark Burns moderately and tans average Burns minimally tans easily and above average 2 4 7 3 6 9 2 12 10 12 12 VCO ELLET 23713 024 Using Your Sunbed When connected to the T Max Manager or T Max 1A or 3A Operation Using Your Sunbed S A B C D E F G Face tanner control Turns face tanners on and off during use Units eguipped with face tanner only Shoulder tanner control Turns shoul der lamps on and off during use Units eguipped with shoulder tanner only Body fan control Controls the speed of the body fan during use Body fan speed indicator ndicates speed of fan OFF LOW MED HIGH Timer display Displays remain
23. ng the pins located on the ends of the lamp into the slots on top of the lamp holders and turn the lamp a quarter turn It should click in place Care and Maintenance Lamp and Acrylic Replacement Recommended Replacement Lamps We recommend using the lamps specified below Use of uncertified lamps is a viola tion of Federal regulations and will void your warranty These lamps have an aver age life of 800 1000 hours of effective tanning use Lamps used longer than that begin to lose their effectiveness even though they continue to light Recommended Replacement Acrylics Acrylics vary greatly over time in their ability to effectively transmit UV light Acrylics sold by ETS have been life tested to ensure proper transmission throughout their useful life ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EQUIPMENT SPEED 225R Wolff Model SPD71 T12 225R Bi Pin bench rear module front 8 canopy lamps SPEED M 255R Wolff Model SPD71 T12 255R Bi Pin other canopy lamps Philips Model HPA 400 30s or CosmoTech Model 23045 or 20046 facial unit COSMOLUX RA plus 15504 40W shoulder unit 23 VCO ELLET 23713 024 Removing Replacing Face Tanner Lamps on Face Tanner Models After removing the canopy and or rear lamp module acrylic shields replace the face tanner lamps as follows Step 1 Support the face tanner assembly with your hand while unscrew ing the two retaining screws The face tanner glass casing will
24. not installed see Electrical Connections A T Max terminator has been used See ATTENTION in Electrical Connections If remote is being used other than T Max Manager the exter nal timer may not be activated Remote wiring is incorrect see the instructions provided with the remote interface kit The auto start feature of the remote system is disabled see the instructions provided with your remote system Remote device has not been set The sunbed has not been connected to the remote system see Remote Connections Delay time of T Max Manager has not been set Delay time has expired and session has begun Auto start function of T Max Manager has been turned off Press the timer button to turn on lamps 26 Problem Solution Timer display continues to show a 1 T Max Manager remote system has not yet been set O after the timer button is pressed 2 Sunbed address is not set correctly see Remote Connections Timer display is indicating Er 1 Body lamps are on when they should be off have service technician check the contactor Timer display is indicating Er 2 Body lamps are off when they should be on have service technician check contactor and its wiring from the main timer box Timer display is indicating Er 3 Bench lamps are on when they should be off have service technician check the contactor Units with separate bench contactor only Timer display is indicating Er 4 Bench lamps are off when they should
25. opy arm onto hinge da arm Positioning bolt will Al en the slot t f D gage the slot on top o gt Y hinge arm and hold canopy 0 SS AHTKIGE ARM up while the other bolts are i installed A G Install other bolts as shown Secure all six bolts in place with self 4 Remove this pin and discard Installation Assembly Procedures Parts needed Rear lamp module Secure rear lamp module in place with 8 screws where shown VCO ELLET 23713 024 Installation Assembly Procedures Parts needed Body fan kit Shoulder tanner kit Install the body fan and shoulder tanner as described in the instruction sheets included in their respective boxes J nsiatlation Assembly Procedures Slide the ballast tray under the unit and pull the cords through to the rear Install the access panel by putting it in place and locking with the access panel key VCO ELLET 23713 024 Electrical Connections At the rear of the sunbed connect the power cords from the ballast tray to their respective power receptacles Simply match the plug to the receptacle push on firmly and secure by twisting the threaded locking ring Connect the Control Cord to the tray and the canopy A Remote Control Bypass plug is already installed in a remote control port on the canopy Your sunbed will not operate without the Remote Control Bypass plug or a remote sys
26. r des blessures aux yeux et la peau et provoquer des r actions allergiques Une exposition r p t e peut causer le vieillissement pr matur de la peau et provoquer le cancer de la peau PORTEZ DES LUNETTES PROTECTRICES LE NON RESPECT DE CETTE CONSIGNE DE S CURIT PEUT ENTRA NER DE GRAVES BR LURES OU DES L SIONS OCULAIRES LONG TERME Les m dicaments ou les produits cosm tiques peuvent augmenter votre sensibilit au rayonnement ultraviolet Consultez un m decin avant d utiliser la lampe solaire si vous prenez des m dicaments si vous souffrez d une maladie cutan e ou si vous croyez tre particuli rement sensible aux rayons du soleil Si vous ne bronzez pas au soleil il est peu probable que vous bronzerez sous une lampe solaire Les enfants les personnes g es et les personnes qui ont une peau claire qui br le facilement ne bronze jamais ou alors tr s peu ne devraient pas utiliser cette lampe Pour utiliser ce dispositif tendez vous sous le panneau sup rieur puis abaissez le autant que possible en veillant conserver une distance minimale entre le corps et le panneau de plastique transparent de la partie sup rieure comme illustr afin d viter une exposition excessive N utilisez pas la lampe sans les panneaux de plastique transparents La premi re semaine de bronzage les personnes qui n ont pas un h le initial ne doivent pas se faire bronzer tous les jours Ne vous faites jamais bronzer plus d une fois par jour L
27. re 2 NOTE A T Max 1A with a master chip can be substituted for a 3A in figure 2 Setting the address manually Before connecting your sunbed to the T Max Manager or T Max 1A or 3A the address of your sunbed must first be set Set the id man ually as described below Setting the id 1 Make sure no cables are plugged into your sunbed s remote ports 2 Remove and reapply power to the unit 3 Press and hold the stop button located on the sunbed display for three seconds and release The display should indicate an id number from oF to 252 199 EGO 100 199 599 200 252 152 4 If you are using a T Max 1A or 3A as your remote the id of the sunbed must be set to 1 If you are using a T Max Manager each sunbed must be assigned a different id To set the id press the timer button to count up or the body fan control button to count down until the desired number is achieved 5 Press the stop button to return to the normal display mode VCO ELLET 23713 024 Remote systems using a Control Relay Most non T Max remote systems control the sunbed by the use of a relay The relay oper ates the sunbed by connecting and discon necting a pair of wires leading from the sunbed Refer to the user s manual provided with your remote system to determine if it operates in this way To connect your sunbed to this type of system a remot
28. side edge of the profile until it releases its latching action see illustration next page The profile will then separate from the bed The aluminum frame around the acrylic offers support as well as allowing the acrylic to hinge open without removing it from the bed Standing in front of the bed lift the long edge of the acrylic On the inside of the bench along the front are two supports for the bench acrylic Release them from their clips and swing up to hold the acrylic open You may remove the acrylic by lifting it out of its hinge channel along the back edge The other acrylics are held in place by four turn latches each Use a flat bladed screwdriver to turn the latches a quarter turn to open the acrylic The canopy and rear lamp module acrylics also swing open on a hinge and may be removed by lifting out of the channel along the back edge When you are finished simply reverse the above directions to secure the acrylic shields Make sure the profile on the bench snaps back in place VCO ELLET Care and Maintenance Lamp and Acrylic Replacement REAR LAMP MODULE ACRYLIC BENCH ACRYLIC ACRYLIC SUPPORT se CANOPY ACRYLIC SA CZ Removing Replacing Lamps After opening or removing the acrylic shields replace lamps as follows Step 1 Grasp a lamp at one end and at the middle and turn the lamp one quarter turn Gently remove the lamp from its holders Step 2 Reinstall the lamp by inserti
29. swing downward Step2 The lamp can now be exchanged The lamp holders are equipped with spring con tacts which enable the lamp to be removed easily Remove the old lamp and discard Install the new lamp using a clean cloth or paper towel Ensure that the lamp is firmly seated in the lamp holders Care and Maintenance Lamp and Acrylic Replacement Note Never take hold of the lamp such that your fingers are in contact with the lamp glass Finger oils will greatly reduce the lamp s operational life Step 3 Gently close the face tanner glass casing and lock it closed with the screws Ensure that the screws firmly secure the glass casing DANGER Never turn the equipment on while the face tanner is disassembled or when the glass filters have been removed The direct light can cause severe injury to the eyes and other areas of the body Immediately discontinue use of this equipment if the face tanner glass is bro ken or if any unfiltered light can be seen escaping the face tanner assembly RETAINING SCREWS Lle ce 24 Troubleshootin Problem Solution Sunbed not tanning 1 Clean sunbed see Thorough Periodic Cleaning 2 Ensure supply voltage is between 208 and 230V AC 3 Replace lamps if lamp hours are greater than 800hrs 4 Replace acrylic Lamps fail to light and timer dis 1 Make sure the unit is connected to a power source play is blank 2 Check source of AC power Reset cir
30. t in place when the unit is on The airflow arrow on the side of this filter should point down The filter hanging under the bench should be installed with the arrow point ing UP MAINTENANCE HEIGHT RELEASE HANDLE AD LIFT ADJUSTMENT VCO ELLET 23713 024 Remote Connections Your sunbed incorporates advanced circuitry allowing it to connect and communicate with most remote control systems If a remote sys tem is to be used first determine whether the remote system is a T Max System or a stan dard remote system operating with a control relay Follow the appropriate instructions for your system type Warning The remote connection is not designed to supply or accept high voltage nor can it provide power to an external timer The sunbed s remote interface circuitry operates on 5 volts attempting to connect it to any higher voltages will damage the sunbed as well as void your warranty T Max Manager figure 1 Installation Remote Connections T Max Products The T Max remote systems offer the ultimate in sunbed control while allowing the tanner easy straightforward operation Your sunbed is configured to directly connect to this system The circuitry inside your sunbed eliminates the need for the T Max 1A or 3A when con necting to the T Max Manager series Your sunbed supports the auto addressing feature of the latest T Max Manager models and the following parameters 2 5
31. tem connected as described in Pre Installation Planning REAR LAMP MODULE POWER PLUG BENCH POWER PLUGS a Installation Electrical Connections NOTE Your sunbed is designed to accept an input from a remote control device The remote control is optional If you plan on using a remote system refer to Remote Connections ATTENTION Although the Remote Control Bypass plug provided with your sunbed will work wherever a T Max ter minator is called for in the series the T Max terminator will not work as a bypass plug Normally a4 bypass plug is l needed only when your CANOPY POWER PLUGS Pa s sunbed is oper ated without a remote system connected CONTROL RECEPTACLE ok O MAIN POWER CORD 4 REAR OF BALLAST TRAY 12 Installation Final Adjustments Final Adjustments Your sunbed uses a smooth gliding spring lift system to raise the canopy This lift sys tem may need to be adjusted slightly due to shipment Remove the front access panel Use a wrench to turn the hex shaped Lift Adjustment lugs shown below clockwise for more lift and coun terclockwise for less When adjusted properly the canopy should raise easily as well as rest fully closed Always adjust both lugs equally AIR FILTERS Make sure the air filters are in place The filter on top of the ballast tray simply sits over the vent holes Airflow holds i
32. uring the first 50 hours of operation Recommended tanning times should therefore be reduced by approximately 10 during that period WARNING Read the instructions booklet before using this sunlamp product All persons in the room should wear protective eyewear when lamps are on Recommended eyewear provided eyeshields Lucas Products Super Sunnies or Intrexco No 5635 1 or equivalent eyewear as defined under 21 CFR 1040 20 Other types of eyewear may not provide adequate protection Failure to use protective eyewear may result in severe burns or other eye injury If discomfort develops discontinue use and consult a physician ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THIS EQUIPMENT SPEED 225R Wolff Model SPD71 T12 225R Bi Pin see illustration O SPEED 255R Wolff Model SPD71 T12 255R Bi Pin see illustration Philips Model HPA 400 30s or CosmoTech Model 23045 or 20046 facial unit COSMOLUX RA plus 15504 40W shoulder unit A THIS EQUIPMENT MUST BE EARTH GROUNDED ER Sa THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS FOR SUN D LAMP PRODUCTS UNDER 21 CFR PART 1040 20 iii DISCONNECT POWER BEFORE ATTEMPTING TO CLEAN RELAMP OR ENGAGE IN THE MAINTENANCE OF THIS PRODUCT VCO ELLET 23713 024 Safety Information DANG R Rayonnement ultraviolet Veuillez suivre les instructions Evitez une exposition excessive Tout comme pour les rayons du soleil une exposition excessive peut cause
Download Pdf Manuals
Related Search