HSM-04-04 - Hall Research
Contents
1. HSM Mai Remote Control Console Definition Definition a O m 2 Tx Rx gt 4 NC NC 6 NC NC x 8 NC 8 NC 9 NC 9 NC Table 1 RS 232 Control Port Pin out LJ The HSM matrices are available with IP network port HSM I On these units there is an RJ45 10 100 Base T for connection to your Local Area Network LAN These units feature a user friendly and powerful built in web server that allows control of the matrix via any browser for control using web enabled controllers 2 2 Connection Block Diagram LAPTOP HD RECIEVER DVD BLU RAY lt HSM 04 04 CONTROL VIA Front Panel lt IR Remote RS 232 pe i a TV LCD DISPLAYS Figure 6 Connection Block Diagram nn 3 Configuration amp Operation 3 1 Front Panel Buttons and Indicators An image of the front panel for the 4x4 matrix is shown below The 4x2 units have fewer OUTPUT buttons but otherwise are the same OUTPUT ee p Beis i gt Bona iv Bs Sessa f f IR Detector Eye Input and Output Channels Control Buttons Routing Status Power Figure 7 HSM 04 04 front panel controls amp indicators The front panel can be used for the following purposes e Monitor amp Control Power On Off status e View current Input output routings ties on Routing Status LED Grid on the front panel e Make new ties either starting from input or from output e Recall preset patterns e Save preset patterns All o2. Selection Colours Default Settings load Connection Da Save Proxy Telnet Delete Rlogin H SSH L Serial Close window on exit C Always Never Only onclean exit About Help Cancel Figure 16 Putty client configuration To use this interface the user must open a TCP socket connection on port 6324 using a compatible telnet client to communicate with matrix Figure 16 shows an example of using the PUTTY client on a Windows compatible PC Mac and Linux users can use the default telnet client Note Regarding Telnet Port The standard telnet port for the Matrix is 6324 however older units shipped prior to 2012 may use port 45454 instead 6 1 Telnet Interface Commands Telnet interface uses same commands as HSM serial RS232 interface as described section 4 above The expected responses on the telnet interface are the same as serial interface Avoid Using Invalid Commands If you are planning to control the Matrix via Telnet please make sure that the controller does not send debug or other irrelevant communication to the Telnet port as this may hang up the Matrix 7 Troubleshooting There are no field serviceable parts or circuits in the device Opening the device will void the warranty If you think the device is malfunctioning please contact Hall Research 7 1 Contacting Hall Research If you determine that your Genesis Matrix is malfunctio
3. HDMI Video and Audio always routed together Video routing commands specified are from the point of view of the output The wildcard character is acceptable for output but not input In addition these commands can be used to monitor or query the status of system ties Omitting the input channel will result in a response of the current routing for that output Important Note on Control Notice about Additional Commands Commands Almost all commands issued to the Matrix HSM matrices equipped with IP Port have will elicit a response from the Matrix once special Serial Commands to change IP the command is accepted and execution address parameters completed After issuing any command you must wait for the matrix s response prior to Please refer to section 5 3 for IP specific sending another command If you send serial commands another command prior to completion of the previous one the matrix might ignore the 2 command Command Response Variations Command Response Command Response COn m lt cr gt stands for Connect Output n to input m COn m lt cr gt COn lt cr gt stands for Connect Output n Query COn m lt cr gt CO m lt cr gt stands for Connect All Outputs to input m CO1 m lt cr gt CO2 m lt cr gt CO3 m lt cr gt for 4x4 matrices only CO4 m lt cr gt for 4x4 matrices only 4 2 Preset Save and Recall Functions Command Response Command Response PRx lt cr gt stands for
4. 3 3 Making AV Routings or Ties from Front Panel ccccccssscsssssscssssesssecssesessessssseeesseeees 9 3 4 Making AV Routings or Ties Using IR Remote cccccccccssecssesssscsssscssssseessecssessseeserees 10 3 5 Saving Presets routing PatterNs cccssessecsesssseescsssssecessssteescsssseeessssseeersessseeesetes 10 3 6 Recalling Presets routing patterns cccssssssssesssesssessssssssssessesssseseessssesersessssererees 10 4 Control Commands RS 232 and IP sssssscessssssesceeseseeeeseseeesanseseeeseeaseeseeneannsesneneans 11 APA ROUUNG FUNCIONS nenosia E denna anise lanctver tee 11 4 2 Preset Save and Recall Functions sesame seein onan cise sueane stad ce 12 AOI OWEN FUNCIONS viiei Pec sedss a cede dndnd cade O E 12 44 Special ComManNdS eee eee eRe een ee cere Rear ee teeter er ttre ner omer ent ree rae eer 12 Ao VANE Commands nersessnerinen teen coll recs a 13 SIP Control Basies sitrscsinciscisvsaredcstestsccuntareneassednanedeneinnieherain menace 14 51 Getting Device IP Adres S ace ateecs ante hac R stacae saat 15 5 2 Controlling the Matrix via Web Interface ccccecccsccsesscssssssssscsssesesssecsssesecsssesesseeesseeees 15 5 3 IP Specific Serial CommandS s snsnsnnsnenennnsnsinannnnnnnnnsinnnnnnnninannnnnninnrnnnninnrnnnnnnnnnnnnnnne 20 i EIGEN STAG Gerini i e a 21 6 1 Telnet Interface COMmMAndS vss ceitnenincns eae ecsaasivetacuanauenanenaes 21 Ts MPOUDIGS MOO UNG Siira 22 1 Contaci
5. D TrueHD DTS HD 100 VAC to 240 VAC 50 60 Hz external 5 VDC 6 A regulated Fully loaded 17 watts max 3 4 amps 5v Storage 40 to 158 F 40 to 70 C 10 to 90 non condensing Operating 32 to 104 F 0 to 40 C 10 to 90 non condensing Convection Front panel 1RU 19 Rack mountable Metal 1 69 H x 17 3 W x 7 68 D F P Width is 19 43 mm H x 440 mm W x 195 mm D 9 Ib 4 kg 10 Ib 4 5 kg Locking High Performance HDMI cables ISTA 1A in carton International Safe Transit Association CE CE FCC Class A 90 000 hours 2 years parts and labor Specifications are subject to change without notice Appendix 1 Front Panel Quick Reference Guide g eis Bs Ean i BOo80 of Figure 17 Control buttons on the front panel OUTPUT Function Procedure View ties or Make ties Hit any of the INPUT or OUTPUT Buttons To change ties hit any INPUT or OUTPUT then hit SET Hit PRE button lights up Hit any INPUT or OUTPUT button Hold PRE until it starts blinking Hit any INPUT or OUTPUT button To turn on hit power button Recall Presets Save Presets Power ON OFF Appendix 2 Command Summary 0D OD OD OU DO To turn off Press and hold power button Command Function Power on off x 0 power off 1 power on Omitting x will show current power status Connect Output n output m input Q Omitting m will show current connections Preset Recall x preset can be 1
6. on input with HDCP This command is useful for several purposes For example if you do not have HDCP compliant displays on all outputs and you try to send an input with HDCP to an output display that is not HDCP compliant you will not get an image This command enables you to check the status of each input and only route content that can be displayed to those outputs In addition since this command detects presence of video on inputs you can use it to check status of inputs and reroute outputs if there is no video on the input currently routed stands for EDID Emulation x 1 default HDTV x 0 Fully Emulated Hall Research DVI EDx lt cr gt This command is used to change the way EDID is reported to the sources The default setting is 1 In this mode the EDID is algorithmically constructed based on the capabilities of all the LCD s connected at all outputs The special setting is 0 In this mode the first 128 bytes of EDID table correspond to Hall Research canned emulation in which most standard PC both 4x3 and 16x9 resolutions are reported to all the inputs This mode should be used if your inputs are from PC s DVI and you are having trouble getting the full complement of resolution choices Please note that after changing the EDID emulation mode you must either unplug and reconnect the unit or issue a FB firmware boot command ED lt cr gt This command is used to query the current setting of the EDID Emulation setting st
7. will report as supporting HDMI 1 3 to each input source in order to receive the deepest color depth possible EDID management fast switching low profile only 1 RU PRESET Save and Recall functions IR remote and comprehensive front panel controls make the Genesis Digital matrices ideal for home theater conference room multimedia presentation systems and other similar settings The Matrix Switchers are optionally available with IP LAN port that allows control from any browser via HTTP web server including web enabled smart phones for control through other web appliances The web interface allows the user to assign custom names for each input output and preset pattern making control over IP a snap 1 2 Features Compatible with HDMI version 1 3 1 4 for color depth and 3D and DVI Supports a wide range of HDTV HDMI and PC DVI resolutions from 480i to 1080p and VGA to WUXGA Supports digital video formats in Deep Color 12bit Supports lossless digital audio both 5 1 and 7 1 Dolby TrueHD Dolby Digital Plus and DTS HD Master Audio Powerful and intuitive front panel controls Preset Save and Recall of commonly used routing patterns EDID management prioritizes the highest capable displays HDMI 1 3 takes precedence over 1 2 and HDMI support supersedes DVI Internal EDID emulation user selection option Output video signals are de skewed and recreated with perfect timing and are jitter free Includes IR re
8. Err IP Address is not valid or IP address not changed Command SB lt space gt lt subnet_address_value gt lt cr gt Where subnet_address_ value stands for the desired subnet mask Success Response SUBNET lt subnet_address_value gt Error Response Err SUBNET Address is not valid Command GW lt space gt lt gateway_address_value gt lt cr gt Where gateway_address_ value stands for desired gateway address Success Response GATEWAY lt gateway _address_value gt Error Response Err GATEWAY Address is not valid Notice User MUST enter ALL THREE Commands mentioned above with the correct values and must get success response for each in order to change the network settings The following message confirms that user has received a success response for all of the above commands and device is applying user settings Applying settings to Matrix please wait If you did not receive the above message renter ALL THREE values again WAIT until you see following Welcome message on Screen It confirms that device has done with applying settings and serial interface is ready for other commands Welcome to Hall Research HSM matrix 5 3 2 Restoring factory defaults Command FD lt cr gt Response Applying Factory Defaults To Matrix Please Wait For Welcome Message This command loads factory defaults for both IP interface and all routing memory including presets This command is available only f
9. HALL RESEARCH USER S MANUAL HSM 04 04 HSM 04 02 Genesis Digital HDMI DVI Matrix Switch Series HSM 04 04 4x4 HDMI Matrix Switch with RS 232 HSM 04 04 4x4 HDMI Matrix Switch with RS 232 amp IP HSM 04 02 4x2 HDMI Matrix Switch with RS 232 HSM 04 02 4x2 HDMI Matrix Switch with RS 232 amp IP CUSTOMER Order toll free in the U S 800 959 6439 SUPPORT FREE technical support Call 714 641 6607 or fax 714 641 6698 INFORMATION Address Hall Research 1163 Warner Ave Tustin CA 92780 Web site www hallresearch com E mail info hallresearch com UMA1181 Rev D Genesis Digital HDMI Matrix Switches TRADEMARKS USED IN THIS MANUAL Hall Research and its logo RFS are trademarks of Hall Research Any other trademarks mentioned in this manual are acknowledged as the property of the trademark owners FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment generates uses and can radiate radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been designed to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules which are intended to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a resident
10. Preset Recall x preset 1 8 CO1 mi lt cr gt CO2 m2 lt cr gt CO3 ms lt cr gt for 4x4 matrices only CO4 ma lt cr gt for 4x4 matrices only PSx lt cr gt stands for Preset Save x preset 1 8 None the current tie pattern is saved in EEPROM 4 3 Power Functions Command Response PWi lt cr gt stands for Power On PW1 lt space gt lt cr gt CO1 mi lt cr gt CO2 m2 lt cr gt CO3 ms lt cr gt Only for 4x4 matrices CO4 ma lt cr gt Only for 4x4 matrices Important Note on Power ON Command This command can take up to 10 seconds to complete Upon powering up the unit will recall the previous state of each output prior to powering off and restore each connection Command Response Variation Command Response PWO lt cr gt stands for Power Off PW0O lt cr gt PW lt cr gt stands for Power Query PWx lt cr gt lt lf gt x 0 off or 1 on 4 4 Special Commands Command Response FB lt cr gt stands for Firmware Boot Depends on power state when the command was issued This command is equivalent to unplugging the power supply and reconnecting it 2 Command Response Command EDx lt cr gt Response Variation Command ST lt cr gt Response Command Response Genesis Digital HDMI Matrix Switches HDm lt cr gt stands for HDCP Status Query on input m HDm x lt cr gt x 0 no video detected on input x 1 video detected on input without HDCP x 2 video detected
11. ands for Status Query PW1 lt cr gt CO1 mi lt cr gt CO2 me lt cr gt CO3 m3 lt cr gt CO4 ma lt cr gt HD1 x1 lt cr gt HD2 xo lt cr gt HD3 x3 lt cr gt HD4 xa lt cr gt FR lt cr gt stands for Factory Reset FR lt cr gt PWO lt cr gt This command is used to clear all the preset ties in memory It also connects all the outputs to the same input and powers the unit off If your unit also has an IP interface this command does not erase user defined names nor IP address assignments Please see FD command in IP section which does the same but also restores the IP interface to factory default status 4 5 Invalid Commands Avoid using invalid commands Lengthy garbage strings or irrelevant RS 232 data sent to the matrix can cause system crash Wrong commands or those with syntax error will prompt the following response INVALID COMMAND lt cr gt nn 5 IP Control Basics Serial Control Matrix Command Port 80 i HTTP ee Processing IP Control Control Port 6324 Telnet Telnet Server Control Figure 10 IP Control Block Diagram As shown in the figure above the matrix can be controlled via RS232 Serial port or through an IP Ethernet port if equipped The IP interface features a built in web server allowing web browsers running on different devices computer smart phone tablet on the network to control and monitor matrix through HTTP protocol on port 80 Section 5 will walk yo
12. ar of the box Press the input channel you want the output connected too cO O 9O 0O OUTPUT Note that the IR remote makes connections as soon as you hit o0 O O 4 the button It takes about 1 to 2 seconds for the matrix to do the routing Figure 8 IR HDCP handshake requires a little time so if you are going to change more than one output pause for moment between pressing the buttons 3 5 Saving Presets routing patterns The number of presets accessible from the front panel is the same as the total of input and output buttons Therefore each front panel button can memorize a pattern For a 4x4 matrix you can recall 8 presets and for a 4x2 you can recall 6 presets However through the IP or Serial port the unit can store and recall 8 presets regardless of matrix configuration Current tie configurations can be saved as presets 1 through 8 for later recall To save the current AV routing pattern press and hold the PRE button for 3 sec the backlit LED will start flashing this means that save function is activated Press the desired input button to save the preset then press the SET button to complete the operation 3 6 Recalling Presets routing patterns Press and release the PRE preset button The button will light up solid Then press and release one of the channel buttons and hit SET Genesis Digital HDMI Matrix Switches 4 Control Commands RS 232 and IP The Genesis Matrices can be controlled v
13. e matrix output The also shows the current tie status and is updated in real time Recall Preset Previously saved ties may be saved in the matrix and can be recalled for quick changes to the matrix First select the desired preset you want to load from the dropdown menu and then click the Recall Preset button to load an existing configuration from memory Save Preset Select the preset name from the dropdown menu and Click Save Preset to save current tie pattern as a preset with that name ON OFF These buttons show the status of matrices power and can be used to turn it on and off The button with red border is the current state and cannot be clicked For example in figure 13 above the matrix is ON and you can turn it off by clicking the OFF button 5 2 2 Labels Tab The user can assign descriptive names inputs MALL outputs and presets on this tab GS RESEARCH HSM IP Manager Video Labels Settings Label names are limited to 16 characters long INPUT 1 VINPUT 1 including white space and can have special INPUT 2 VINPUT_2 symbols INPUT 3 VINPUT_3 Apply Button INPUT 4 VINPUT_4 Click this button to save your changes after OUTPUT 1 VOUTPUT_1 changing the names OUTPUT 2 VOUTPUT_2 f OUTPUT 3 VOUTPUT_3 5 2 3 Settings Tab OUTPUT 4 VOUTPUT_4 Settings tab helps user to change IP address PRESET 1 PRESET 1 enable disable DHCP enable disable password change current password and load factory default setting
14. f the front panel switches have built in LEDs that help in the operation Front panel functions are designed for maximum intuitiveness With just a little practice one can easily learn to monitor and control the matrix 3 2 Turning the unit on and off To turn the unit on press the power button The unit performs a simple LED test where all buttons and LED s are gradually turned on over a few seconds Then the matrix will recall the last routing pattern prior to being shut down and update the Routing Status LED Grid To turn the matrix off press and hold the power button for 5 seconds This is done to prevent accidentally turning off the unit if the power button is accidentally pressed Genesis Digital HDMI Matrix Switches 3 3 Making AV Routings or Ties from Front Panel To make the unit as convenient and intuitive as possible the HSM matrix allows you to make ties starting from the input channel s point of view or from the output 3 3 1 Making a tie starting from the output This is the most natural way of making connections since each output gets its signal from only one input Q Note that once you start making selections from the front panel if you do not hit any buttons for approximately 10 seconds the system will exit this mode without any user interaction First press one of the output channel buttons That output button will light up and the current input routed to that output will light up At this poin
15. ia an external control system by using either the standard RS 232 or the optional IP port Any program capable of standard serial communication in ASCII format is capable of working with the matrix Most PCs with Windows OS have HyperTerminal or equivalent There are also many free Terminal Emulator software programs available for download on the internet Note on RS 232 port availability on PC Most PCs and notebooks do not come equipped with a serial RS 232 port Therefore for serial control from a PC you may need a USB to RS 232 converter These are available from Hall Research Model USB RS232 1 Figure 9 USB to RS 232 Adapter Use a DB9 Male to Female cable per Table 1 to connect the unit to the PC s serial port Use 9600 Baud 8 bits No Parity 1 Stop bit No flow control Upon power up the Matrix will output a screen similar to below through its serial port Special characters shown in lt gt brackets lt cr gt is the carriage return character 0x0D lt lf gt is the line feed character Ox0A COMMAND MEANING PWO lt cr gt POWER IS OFF CO1 1 lt cr gt INPUT 1 ROUTED TO OUTPUT 1 CO2 2 lt cr gt INPUT 2 ROUTED TO OUTPUT 2 CO3 3 lt cr gt INPUT 3 ROUTED TO OUTPUT 3 CO4 4 lt cr gt INPUT 4 ROUTED TO OUTPUT 4 HD1 0 lt cr gt NO VIDEO INPUT ON OUTPUT 1 HD2 0 lt cr gt NO VIDEO INPUT ON OUTPUT 2 HD3 0 lt cr gt NO VIDEO INPUT ON OUTPUT 3 HD4 0 lt cr gt NO VIDEO INPUT ON OUTPUT 4 4 1 Routing Functions NOTE
16. ial area is likely to cause interference in which case the user at their own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment CAT yWiCATIC Ks S Q QO C zZ s FC c 7 u D OQ V Cc w a H r s m Compliant HOM HIGH DEFINITION MULTIMEDIA INTERFACE Contents DAM PVEPO CG HON irisada a a aai 3 EEEE K E A sng LE A E dt E T 3 Ni NEI OS ane etd ncn accel santa caas acpi bd acy Seas naeueaia ots assaeph ahd auadoasacmaadacaaauanadls 4 Zi MVS CANAL ONT 5c etree A E atin ace E E E E E E E R auseneueesetuaacemennnbenels 5 21 Rackage COmMent sa tise teens cite ae dae A eae hand a a eg ae 5 2 2 Input and Output Connection 55 xsiescirc sie ticatuassacacnesctataneiacutdscanendh agate sauneianaancumeieie 5 Table t RS 232 Control Port PIN OUt isecnsssseanianen nae T 2 2 Connection Block Diagram e s ssssesnsiseesnsnsinnnsrnnsninannnnnnnnannnnnninannrnninnnnrnnnnnnnnnnrnrnnnnnnnnnt T 3 Configuration amp OPSratiOn sissssscaiersisececcesesssevereesivicseasussavecdvarssnesevanvavecdeavasheuoubevdreeessteruaiavies 8 3 1 Front Panel Buttons and IGICAONSsisaavutineasaanece As vai Ais adeuetueeisaaraanatea es 8 32 lumino THE unit OM ANG ON eee sascces ck caccrscas cu ccmedce sara eanneg ncanusakenenaucelauecheuntamaunenieeen 8
17. l Connections for HSM I 04 04 Q Using quality HDMI cables connect the inputs to video sources Q Ifthe sources are DVI PC then you will need either a DVI to HDMI adapter or preferably a DVI to HDMI Cable Figure 3 Model C HDMI DVI xM x 2 3 or 5 meters 1 Q For a professional installation we recommend using locking HDMI cables The Matrix Switch has a tapped hole above each HDMI connector and the locking cables available from Hall Research come with screws and stand offs for securing the cables in place so they don t accidentally get unplugged Figure 4 Model C HDMI L x x 1 5 3 6 10 15 25 35 or 50 ft Next connect the HDMI outputs to the displays Plug the power supply to the unit Use only the supply that came with the unit LJ There is an IR remote detector eye on the front panel of the unit however if the unit is to be situated in a closet or enclosure it may be necessary to use an IR detector cable and locate the eye somewhere more convenient Hall Research can provide such a cable that will plug into a jack on the rear of the HSM matrix Gwe Figure 5 Model CIR DET D1 Genesis Digital HDMI Matrix Switches If the matrix needs to be controlled via RS 232 plug the controller or PC to the DB9 Female port on the rear of the matrix Make the connection to the PC s DB9 Male connector using a straight through DB9 MF cable
18. mote control Front panel IR sensor and rear panel connector for optional IR detector cable for instances where the unit is not in line of sight Supports HDMI cables up to 15 meters 50 feet long on its input and drive cables to 15 meters on the outputs Includes RS 232 port with Hall Research s Genesis Control Command Set GCCS Optional IP LAN port for browser control Optional IP LAN versions includes web server with easy to use controls customizable with user definable names for each input and output 1RU high compact amp rugged rack mountable metal enclosure Uses Silicon Image founding member of HDMI Chipsets Assembled in USA Genesis Digital HDMI Matrix Switches 2 Installation 2 1 Package Contents Your package should contain the 1RU Matrix Switcher a Universal power supply 5v DC 6A an IEC320 Power Cord an IR remote control and a User s Manual Figure 1 Power Supply and IR Remote Notice Use only regulated 5v DC supply center positive as supplied with the unit Use of any other voltage will cause damage to the unit and void the warranty 2 2 Input and Output Connections The matrix is housed in a 1RU 19 wide rack mountable enclosure All of I O control and the power connections are on the rear of the unit Serial Control Ethernet IP port A V Outputs with locking connector taps A V Inputs with locking connector taps Power IR detector in Figure 2 Rear Pane
19. ng Hall RESCAUCIN iscsi esd accede nese easiest ance a rae RAA 22 1 2 OMIDDING and PaACKAG IAG sersan ase tail Sarat eal acl Sar at al aides apse erie 22 8 Specifications anionit insi anainn eanan amaaa anaana needa ead Ea A 23 Appendix 1 Front Panel Quick Reference Guide sssssssssssnsssnssnsnsnnnnnnnnnnsnnnnnnnnnnnnnnnnnns 24 Appendix 2 Command SUMMArYy s sssssssssssssrsnssnsnsnnnnnnnnnnnnnnnnnnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnna 24 2 ne Genesis Digital HDMI Matrix Switches 1 Introduction 1 1 General Thank you for purchasing this professional quality and compact Genesis Matrix Switch from Hall Research This User s Manual applies to both 4x2 and 4x4 HDMI Matrix Switchers As members of Hall s Genesis series these matrices are synonymous with high performance intuitive and powerful user interface easy to use control command set and unsurpassed reliability The Matrix switches are HDMI 1 3 compliant and 1 4 for color depth and 3D support HDCP deep color multi channel digital audio up to 7 1 channels and may be used with any combination of DVI PC or HDMI HDTV sources and displays The Matrix uses Silicon Image chipsets capable of color depth conversion independently for each output This assures that the highest numbers of colors possible are displayed on each output In other words if some outputs are connected to displays that only support HDMI 1 2 and others to 1 3 the unit
20. ning do not attempt to repair the unit instead contact Hall Research Technical Support at 714 641 6607 Before you do make a record of the history of the problem We will be able to provide more efficient and accurate assistance if you have a complete description 7 2 Shipping and Packaging If you need to transport or ship your unit Package it carefully We recommend that you use the original container Before you ship the units back to Hall Research for repair or return contact us to get a Return Authorization RMA number Genesis Digital HDMI Matrix Switches 8 Specifications Video Standards Signal type Connectors Video Data Rate Supported Colors HDMI Cable Length HD Resolutions PC Resolutions Audio Supported Formats General Power Supply Nominal Power Temperature humidity Cooling Mounting Enclosure type Dimensions Product weight Shipping weight Recommended cable Vibration Safety EMI EMC MTBF Warranty HDMI 1 3 1 4 compliant for video color depth and 3D DVI single link TMDS video DDC EDID 0 to 5 v TTL HDMI Type A Female with Locking 2 25 Gbps RGB YCbCr 4 4 4 YCbCr 4 2 2 xvYCC From source 15 m 50 ft at any resolution or color depth to display 15 m 50 ft 1080p or 7 5 m 25 ft at deep color 480i 480p 576i 576p 720p 1080i 1080p 8 or 12 bits per channel 24 or 36 bits aggregate VGA through UXGA PCM2 PCM5 1 PCM7 1 Dolby5 1 DTS5 1 DD
21. or units that have IP interface With this command you don t need to use FR command since as part of the action it performs the FR function as well Wait until you see following welcome message on terminal screen Welcome to Hall Research HSM matrix serial interface Please refer to user manual for matrix serial commands 20 Genesis Digital HDMI Matrix Switches 6 Telnet Interface The HSM telnet interface is an IP based command line interface to control and monitor the matrix Only one 1 client is allowed to connect at a time through this interface and with every new connection the old connection will be automatically closed The Telnet connection timeout is set to infinity or until the user closes the current connection The Telnet authentication required depends on authentication status of web interface If telnet authentication is enabled the password required will be same as what used for web interface The user can also disable the telnet interface from the web interface a i LX PuTTY Configuration Put current HSM IP Address here 2 x Category E Session L Bal Pptions for your PuTTY session Lo ggng M Specify the dj ftination you want to connect o E Terminal Keyboard Hist Name ip address Port Features Connection type F Window Haw C Telnet C Rlogn SSH Serial Appearance sate fini Behaviour 2 Translation Saved Sessions Load save or delete a stored session
22. rix web interface allows the user to change monitor the matrix I O ties assign unique names to the inputs outputs and presets as well as enable disable password protected login or change the IP configuration etc The Preset Input and Output names are saved permanently in matrix until the user changes them The matrix will also remember the I O Presets when not powered The web interface is user friendly and easy to access It consists of three tabs named Routing Labels and Settings Each tab and its features are explained in next sections Genesis Digital HDMI Matrix Switches 5 2 1 Video Routing Tab The routing tab allows the user to control the matrix I O ties save the current configuration as a preset load existing presets and turn the matrix on or off Please refer to Figure 13 for a typical example screen of the routing tab as it would appear on a Smart Phone MALL FRR BESEaRcH HSM IP Manager Video Labels Settings Outputs Inputs Lobby Select One v Conf Room Select One v Storefront Select One v Training Room Select One v Select Preset v Recall Save Power ON OFF Figure 13 Video Routing Tab Outputs Column Displays the name for the selected matrix output You cannot change the output names labels here Labels can be changed using the Labels tab Inputs Column Two for a 4x2 matrix or four for a 4x4 matrix dropdown buttons allow the user to select the desired matrix input to tie to the respectiv
23. s whenever necessary ESET PRESET_S PRESET 4 PRESET_4 PRESET 2 PRESET_2 PRESET 5 PRESET_5 Name PRESET 6 PRESET_6 User defined name for this matrix The name PRESET 7 PRESET 7 can be sixteen 16 characters including any PRESET 8 PRESET_8 white space and special characters Apply Location Figure 14 Labels Tab User defined location of this matrix Location can be twenty 20 characters long including white space and special characters ire RESEARCH HSM IP Manager Video Labels Settings IP Displays the current IP address of this matrix and if DHCP is disabled allows the user to enter a new IP address NAME HSM Matrix LOCATION Hall Research A 192 168 1 200 SUBNET 255 255 255 0 Subnet GATEWAY 192 168 1 1 Displays the current SUBNET MASK address DHCP Enable Disable of this matrix and if DHCP is disabled allows LOGIN Enable Disable the user to enter a new subnet mask oe Apply Gateway Factory Reset Change Password Displays the current GATEWAY address of this matrix and if DHCP is disabled allows the Figure 15 Settings Tab user to enter a new gateway address Genesis Digital HDMI Matrix Switches DHCP Enables Disables DHCP If enabled the matrix is assigned an IP address from the user s compatible networks DHCP router This is the factory default If disabled the matrix is assigned the IP address subnet mask and gateway address supplied by the
24. t if you change your mind and do not want to make any changes just hit SET If you want to change to another output channel use either the up and down V buttons to walk through other outputs or just select another output channel To route the output to a different input than the one currently connected to hit the candidate input channel number This does not actually make the connection the new input channel will be blinking Again if you change your mind either hit the same blinking button it will stop blinking or hit another input channel When you are sure you have selected the input channel you desire hit SET 3 3 2 Making a tie starting from the input The procedure is similar to the above but a particular input can be routed to more than one output LJ Press one of the input channel buttons That button will light up and ALL the outputs routed from that input will light up Q If you want to change to another input channel use either the up and down A VY buttons to walk through other inputs or just select another input channel LJ To route the selected input to single or multiple outputs press the output buttons Again these new outputs are only candidates will be blinking and will not be routed until you hit the SET button 3 4 Making AV Routings or Ties Using IR Remote OD 900 The remote control is very simple outputs are labeled as A D and RO O O O they correspond to 1 4 on the re
25. t will scan your LAN and locate any compatible Hall Research devices that are connected 5 2 Controlling the Matrix via Web Interface The Genesis Matrices with IP option have a powerful yet easy to use IP based web interface to control and monitor matrix Web browser application running on any device Computer Smart phone iPad on the same network can use this interface When the matrix is shipped it is configured with a dynamic IP address and when powered up on a compatible network the end users DHCP router will assign an IP address You can find the matrices IP address on your network by using the Device Finder utility available free from the Hall Research website Once you have the correct IP address of your device from the Device Finder utility open a compatible web browser and type hitp your devices ip address in the address bar and hit Enter The web page shown will automatically format the display for the browser it is running on This means that on a Smart Phone the width and character sizes will be optimized so you do not have to deal with zooming and scrolling the screen to use the matrix Furthermore all elements on the web page screen are automatically updated from server side This means that if the video routing is altered by the front panel of the matrix or from another simultaneous LAN connection your browsers screen will automatically reflect the change Figure 12 Control via web Interface The mat
26. to 8 Preset Save x preset can be 1 to 8 Read Input Status n Input Returns O No Video EDID Management O DVI Emulated EDID Firmware Boot Resets the entire system Status Report Factory Reset for IP enabled matrices Factory Reset for Non IP enabled matrices MALL RESEARCH Copyright 2013 Hall Research Inc All rights reserved CUSTOMER Order toll free in the U S 800 959 6439 SUPPORT FREE technical support Call 714 641 6607 or fax 714 641 6698 INFORMATION _ Mail order Hall Research 1163 Warner Ave Tustin CA 92780 Web site www hallresearch com E mail info hallresearch com
27. u through this HTTP based Web Interface The IP interface also supports telnet connection over port number 6324 to control and monitor matrix Section 6 describes the telnet based interface The IP interface on every matrix shipped has a unique MAC address and must have a valid IP address to function properly on your network Notice As shipped from factory DHCP is enabled This means that the users DHCP router automatically assigns an IP address to the Matrix To find the IP address assigned to the matrix use the DeviceFinder Software available free from Hall Research s website Genesis Digital HDMI Matrix Switches 5 1 Getting Device IP Address Ai a The HSM matrix comes Q preconfigured for DHCP which means it will automatically obtain an IP address when it is connected to the users LAN network It is recommended that you set a static P Type Mac Adare Mod Name DYNAMIC 00 704 a0dk5 92 Hall Research V Digital AV Room 24 All of the Hall Research IP enabled devices will appear with IP on each system in order to the appropriate IP addresses listed guarantee it maintains the same address In order to set a static IP first discover what DHCP address was issued to the matrix and then login to the matrix web interface to reconfigure the settings see section 5 2 below Download and install the Hall Figure 11 DeviceFinder Research Device Finder utility Once installed run the program and i
28. user Login Enables Disables the system login password If enabled the matrix will require a password in order to operate the controls If disabled the matrix requires no password to operate the controls This is the factory default Telnet Enables Disables the telnet interface See Section 6 for more details Change Password Allow the user to change the existing system password When clicked a window will open for entering the new password The password length is limited to eight 8 characters long Apply Factory Default Settings for IP interface The User must click this button Field Value GUI Tab after changing any field on settings tab to save the changes Factory Reset This button restores the factory defaults to this matrix Factory default will also wipe out saved presets Hall Research Settings 5 3 IP Specific Serial Commands The HSM matrix is equipped with a standard RS 232 interface which allows the user to assign a static IP address Please refer section 4 to connect a PC to Matrix over an RS 232 serial interface Once you are connected use following commands to change the network settings or restore the factory defaults 5 3 1 Changing the network settings of unit Note All commands are case sensitive Command IP lt space gt lt ip address value gt lt cr gt Where ip_address_ value stands for the desired IP address Success Response P lt ip address_value gt Error Response
Download Pdf Manuals
Related Search