- Geetek!
Contents
1. 38 POI 802 11b g n High Power Wireless AP router w Built in Amplifier Booster 2K C Boost N Part GT APN User Manual ear rR endent Basic Service Set IBSS Example 2 wireless Ad Hoc Mode 5 What is BSSID A six byte address that distinguishes a particular access point from others Also know as just SSID Serves as a network ID or name 6 What is ESSID The Extended Service Set ID ESSID is the name of the network you want to access It is used to identify different wireless networks 7 What are potential factors that may causes interference Factors of interference Obstacles walls ceilings furniture etc Building Materials metal door aluminum studs Electrical devices microwaves monitors and electrical motors Solutions to overcome the interferences Minimizing the number of walls and ceilings Position the WLAN antenna for best reception Keep WLAN devices away from other electrical devices eg microwaves monitors electric motors etc Co Add additional WLAN Access Points if necessary 39 8 What are the Open System and Shared Key authentications IEEE 802 11 supports two subtypes of network authentication services open system and shared key Under open system authentication any wireless station can request authentication The station that needs to authenticate with another wireless station sends an authentication management frame that contains the identity of the s2. Uplink Bandwidth Definition of the setting Delete All Reset Click the Reset button to abort change and recover the previous configuration setting Management Statistics This page shows the packet counters for transmission and reception regarding to wireless Ethernet LAN and Ethernet WAN networks Statistics This page shows the packet counters for transmission and reception regarding to wireless and Ethernet networks Sent Packets 9290 Wireless LAN Received Packets 243574 Sent Packets 2089 Ethernet LAN Received Packets 1 552 Sent Packets 1 044 Ethernet WAN Recelved Packets 0 Refresh Item Description interface Received Packets It shows the statistic count of received packets on the wireless Seeed Paets Canmertace nn eee packets on the wireless LAN interface Ethernet LAN interface 32 WAN interface Ethernet WAN interface Click the refresh the statistic counters on the screen Management DDNS This page is used to configure Dynamic DNS service to have DNS with dynamic IP address Dynamic DNS Setting Dynamic DNS is a service that provides you with a valid unchanging internet domain name an URL to go with that possibly everchanging IP address Enable DDNS Service Provider DynDNS Domain Name User Name Email Password Key Note For TZO you can have a 30 days free trial here or manage your TZO account in control pane For DynDNS you
3. tutte 400 and range 8 140 1460 bytes WAN WAN side VPN connection through VPN connection through VPN connection through configuration setting Firewall Port Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network Port Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network Enable Port Filtering Port Range Protocol Both Comment Apply Changes Reset Current Filter Table PortRange Protocol Comment Select Delete All Enable Port Filtering Click to enable the port filtering security function Port Range Protocol Comments To restrict data transmission from the local network on certain ports fill in the range of Start port and end port and the protocol also put your comments on it The Protocol can be TCP UDP or Both Comments let you know about whys to restrict data from the ports Apply Changes Click the Apply Changes button to register the ports 26 Pp to port filtering list Reset Click the Reset button to abort change and recover the previous configuration setting removed from the port filtering list Delete All Click to delete all the r
4. ISM bands ISM stands for Industrial Scientific and Medical radio frequency bands that the Federal Communications Commission FCC authorized for wireless LANs The ISM bands are located at 915 13 MHz 2450 50 MHz and 5800 75 MHz 4 How does wireless networking work The 802 11 standard define two modes infrastructure mode and ad hoc mode In infrastructure mode the wireless network consists of at least one access point connected to the wired network infrastructure and a set of wireless end stations This configuration is called a Basic Service Set BSS An Extended Service Set ESS is a set of two or more BSSs forming a single subnetwork Since most corporate WLANs require access to the wired LAN for services file servers printers Internet links they will operate in infrastructure mode Distribution System i DSi a SS gt Basic mervice eet Bae Extended Service Set Ess Ad hoc mode also called peer to peer mode or an Independent Basic Service Set or IBSS is simply a set of 802 11 wireless stations that communicate directly with one another without using an access point or any connection to a wired network This mode is useful for quickly and easily setting up a wireless network anywhere that a wireless infrastructure does not exist or is not required for services such as a hotel room convention center or airport or where access to the wired network is barred such as for consultants at a client site
5. Vendor interoperability enabling roaming of 802 11 Stations within IP subnet IAPP defines messages and data to be exchanged between Access Points and between the IAPP and high layer management entities to support roaming The IAPP protocol uses TCP for inter Access Point communication and UDP for RADIUS request response exchanges It also uses Layer 2 frames to update the forwarding tables of Layer 2 devices 21 What is Wireless Distribution System WDS The Wireless Distribution System feature allows WLAN AP to talk directly to other APs via wireless channel like the wireless bridge or repeater service 22 What is Universal Plug and Play uPNP UPnP is an open networking architecture that consists of services devices and control points The ultimate goal is to allow data communication among all UPnP devices regardless of media operating system programming language and wired wireless connection 23 What is Maximum Transmission Unit MTU Size Maximum Transmission Unit MTU indicates the network stack of any packet is larger than this value will be fragmented before the transmission During the PPP negotiation the peer of the PPP connection will indicate its MRU and will be accepted The actual MTU of the PPP connection will be set to the smaller one of MTU and the peer s MRU The default is value 1400 24 What is Clone MAC Address Clone MAC address is designed for your special application that request the clients to
6. able to connect to your Access Point When this option is enabled no wireless clients will be able to connect if the list contains no entries Wireless Access Control lf you choose Allowed Listed only those clients whose wireless MAC addresses are in the access control list will be able to connect to your Access Point When Deny Listed is selected these wireless clients on the list will not be able to connect the Access Point Wireless Access Control Mode ble is MAC Address Comment i Current Access Control List Delete Selected Delete All Item Description Wireless Access Control Mode Click the Disabled Allow Listed or Deny Listed of drop down menu choose wireless access control mode 12 This is a security control function only those clients registered in the access control list can link to this WLAN Broadband Router MAC Address Fill in the MAC address of client to register this WLAN Broadband Router access capability Enter notes for the registered client Apply Changes Click the Apply Changes button to register the client to new configuration setting the previous configuration setting to this WLAN Broadband Router Delete Selected Click to delete the selected clients that will be access Paces fant removed fom this WAN Brosdbond Route access allowed list the previous configuration setting WDS Settings Wireless Distribution System uses wireless media to communicate with other APs li
7. can create your DynDNS account here Item Description To configure Domain Name Password Key sd Key Configure Password Key S O re Password ay service previous configuration setting 33 Management Time Zone Setting This page is used to configure NTP client to get current time Time Zone Setting You can maintain the system time by synchronizing with a public time server over the Internet Current Time Yr 2009 Mon Day 27 Hrli6 Mn 20 Sec 32 Copy Computer Time Time Zone Select GMT 08 00 Pacific Time US amp Canada Tijuana Enable NTP client update Automatically Adjust Daylight Saving NTP server 192 5 41 41 North America v Manual IP Setting Description Click the Apply Changes button to save and enable NTP client service previous configuration setting Click the refresh the current time shown on the screen Management Denial of Service This page is used to enable and setup protection to prevent attack by hacker s program It provides more security for users 34 Denial of Service A denial of serrice DoS attack is characterized by an explicit attempt by hackers to prevent legitimate users of a service from using that service CI Enable DoS Prevention Whole System Hood SYN Whole System Hood FIN Whole System Hood UDP Whole System Hood ICME Per Source IF Hood SYN Per Source IF Hood FIN Per Source IF Hood UDF Per Source IP H
8. in the Network Component Type dialog box and click Add button 5 Select TCP IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP IP protocol it may need the Microsoft Windows CD to complete the installation Close and go back to Network dialog box after the TCP IP installation 6 Select TCP IP and click the properties button on the Network dialog box 7 Select Specify an IP address and type in values as following example IP Address 192 168 1 1 any IP address within 192 168 1 1 to 192 168 1 253 is good to connect the Wireless LAN Access Point IP Subnet Mask 255 255 255 0 8 Click OK and reboot your PC after completes the IP parameters setting For OS of Microsoft Windows 2000 XP 1 Click the Start button and select Settings then click Control Panel The Control Panel window will appear 2 Move mouse and double click the right button on Network and Dial up Connections icon Move mouse and double click the Local Area Connection icon The Local Area Connection window will appear Click Properties button in the Local Area Connection window 3 Check the installed list of Network Components If TCP IP is not installed click the Add button to install it otherwise go to step 6 4 Select Protocol in the Network Component Type dialog box and click Add button 5 Select TCP IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP IP protocol it may need
9. is set to 802 11n only Aggregation Click to enable or disable aggregation function Short GI Click to enable or disable short Guard Intervals function WLAN Partition Enabling WLAN Partition prevents associated wireless clients from communicating with each other RF Output power To adjust transmission power level 11 Wireless Security Setup This page allows you setup the wireless security Turn on WEP WPA WPA2 by using encryption keys could prevent any unauthorized access to your wireless network Wireless Security Setup This page allows you setup the wireless security Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network Select SSID Root AP Wi 1Tbg SSD Encryption 80 1x Authentication Select SSID Select SSID to be encrypted from multiple APs Encryption Select the encryption supported over wireless access The encryption method can be None WEP WPA TKIP WPA2 or WPA2 Mixed Use 802 1x Authentication While Encryption is selected to be WEP Click the check box to enable IEEE 802 1x authentication function Apply Changes Click the Apply Changes button to complete the new configuration setting Reset Click the Reset button to abort change and recover the previous configuration setting Wireless Access Control If you enable wireless access control only those clients whose wireless MAC addresses are in the access control list will be
10. ratio of parallel transmissions is high In contrast with a large fragment threshold the overlap is small and the spatial reuse ratio is low However high fragment threshold leads to low fragment overhead Hence there is a trade off between spatial re use and fragment overhead Fragment threshold is the maximum packet size used for fragmentation Packets larger than the size programmed in this field will be fragmented If you find that your corrupted packets or asymmetric packet reception all send packets for example You may want to try lowering your fragmentation threshold This will cause packets to be broken into smaller fragments These small fragments if corrupted can be resent faster than a larger fragment Fragmentation increases overhead so you ll want to keep this value as close to the maximum value as possible 40 11 What is RTS Request To Send Threshold The RTS threshold is the packet size at which packet transmission is governed by the RTS CTS transaction The IEEE 802 11 1997 standard allows for short packets to be transmitted without RTS CTS transactions Each station can have a different RTS threshold RTS CTS is used when the data packet size exceeds the defined RTS threshold With the CSMA CA transmission mechanism the transmitting station sends out an RTS packet to the receiving station and waits for the receiving station to send ack a CTS Clear to Send packet before sending the actual packet data This settin
11. 192 168 1 253 is good to connect the Wireless LAN Access Point IP Subnet Mask 255 255 255 0 Click OK to complete the IP parameters setting For OS of Microsoft Windows Vista and Windows 7 1 2 3 4 Click Start Button and select Control Panel the Control Panel windows pop up From Network and Internet category choose View network status and tasks Select Change adapter settings right click Local Area Connection select Properties From popup menu in Networking tab select Internet Protocol Version 4 TCP IPv4 then click Properties Check Use the following IP address then Specify IP address as following example Enter your IP Address the IP Address can be any number within the range from 192 168 1 1 to 192 168 1 253 IP Subnet Mask 255 255 255 0 Click OK to complete the IP parameters setting This page shows the current status and some basic settings of the device includes system wireless Ethernet LAN and WAN configuration information It shows the duration since WLAN Broad It shows the firmware version of WLAN Broadband Router Wireless Configuration Mode It shows wireless operation mode Band It shows wireless operation mode SSID It shows the SSID of this WLAN Broadband Router The SSID is the unique name of WLAN Broadband Router and shared among its service area so all devices attempts to join the same wireless network can identify it Channel Number It shows the wireless channel connected
12. AN access type WAN Interface Setup This page is used to configure the parameters for Internet network which connects to the YVAN port of your Access Point Here you may change the access method to static IP DHCP PPPoE PPTP or L2TP by click the item value of WAN Access type WAN Access Type DHCP Client Host Name MTU Size 1492 1400 1492 bytes Attain DNS Automatically Set DNS Manually DNS 1 DNS 2 DNS 3 Clone MAC Address QOO0000000000 Enable uPNP Enable IGMP Proxy Enable Ping Access on WAN Enable Web Server Access on WAN Enable IPsec pass through on VPN connection Enable PPTP pass through on VPN connection Enable L2TP pass through on VPN connection i Me EMSN Apply Changes Reset Wireless Basic Settings This page is used to configure basic wireless parameters like Band Mode Network Type SSID Channel Number Enable Mac Clone Single Ethernet Client Wireless Basic Settings This page is used to configure the parameters for wireless LAN clients which may connect to your Access Point Here you may change wireless encryption settings as well as wireless network parameters C Disable Wireless LAN Interface Band 2 4 GHz B G N v Mode AP Network Type I nfrastructure SSID 802 1 1bgn SSID Channel Width 20MHz v Control Sideband Upper Channel Number 6 Broadcast SSID Enabled v WMM Enabled Data Rate Auto Associa
13. Active DHCP Client Table window that shows current active clients with their assigned IP address MAC address and expire time information Server mode only Select to enable or disable Static DHCP from pull down menu Server mode only is optional field Tree function from pull down menu cloned configuration setting the previous configuration setting 17 Static DHCP Setup This page allows you reserve IP addresses and assign the same IP address to the network device with the specified MAC address any time it requests an IP address This is almost the same as when a device has a static IP address except that the device must still request an IP address from the DHCP server Static DHCP Setup This page allows you reserve IP addresses and assiqn the same IP address to the network device with the specified MAC address any time it requests an IP address This is almost the same as when a device has a static IP address except that the device must still request an IP address from the DHCP server C Enable Static DHCP IP Address MAC Address Comment Static DHCP List Delete Selected Delete All Reset Item Description Enable Static DHCP Click to enable Static DHCP IP Address Enter the Static IP Address in the IP Address field MAC Address Enter the MAC address of the corresponding Client in the MAC Address field 18 WAN Interface Setup This page is used to configure the parameters for wide area net
14. D Broadcast Broadcast of SSID is done in access points by the beacon This announces your access point including various bits of information about it to the wireless world around it By disabling that feature the SSID configured in the client must match the SSID of the access point Some wireless devices don t work properly if SSID isn t broadcast for example the D link DWL 120 USB 802 11b adapter Generally if your client hardware supports operation with SSID disabled it s 41 not a bad idea to run that way to enhance network security However it s no replacement for WEP MAC filtering or other protections 15 What is Wi Fi Protected Access WPA Wi Fi s original security mechanism Wired Equivalent Privacy WEP has been viewed as insufficient for securing confidential business communications A longer term solution the IEEE 802 11i standard is under development However since the IEEE 802 11i standard is not expected to be published until the end of 2003 several members of the WI Fi Alliance teamed up with members of the IEEE 802 11i task group to develop a significant near term enhancement to Wi Fi security Together this team developed Wi Fi Protected Access To upgrade a WLAN network to support WPA Access Points will require a WPA software upgrade Clients will require a software upgrade for the network interface card and possibly a software update for the operating system For enterprise networks an authentication s
15. PPTP client supported by this router to make a VPN connection the IP address for it the subnet mask for it Server IP Address Enter the IP address of the PPTP Server User Name If you select the PPTP support on WAN interface fill in Aaaa er a tog the FTP cere Password If you select the PPTP support on WAN interface fill in the user name and password to login the PPTP server Connection Type Select the connection type from pull down menu 23 There are Continuous Connect on Demand and Manual three types to select Continuous connection type means to setup the connection through PPPoE protocol whenever this WLAN Broadband Router is powered on Connect on Demand connection type means to setup the connection through PPPoE protocol whenever you send the data packets out through the WAN interface there are a watchdog implemented to close the PPPoE connection while there are no data sent out longer than the idle time set Manual connection type means to setup the connection through the PPPoE protocol by clicking the Connect button manually and clicking the Disconnect button manually disconnect your PPTP session 1400 encryption compression Attain DNS Automatically Click to select getting DNS address for DHCP support Please select Set DNS Manually if the DHCP support is selected Set DNS Manually Click to select getting DNS address for DHCP support DNS 1 Fill in the IP address of Domain Name Server 1 DNS 2 Fil
16. Setup Wizard page to define the operation mode Operation Mode You can setup different modes to LAN and WLAN interface for NAT and bridging function Gateway In this mode the device is supposed to connect to internet via ADSL Cable Modem The NAT is enabled and PCs in LAN ports share the same IP to ISP through WAN port The connection type can be setup in WAN page by using PPPOE DHCP client PPTP client L2TP client or static IP Bridge In this mode all ethernet ports and wireless interface are bridged together and NAT function is disabled All the WWAN related function and firewall are not supported Wireless ISP n this mode all ethernet ports are bridged together and the wireless client will connect to ISP access point The NAT is enabled and PCs in ethernet ports share the same IP to ISP through wireless LAN You must set the wireless to client mode first and connect to the ISP AP in Site Surey page The connection type can be setup in YVAN page by using PPPOE DHCP client PPTP client L2TP client or static IP Time Zone Setting This page is used to enable and configure NTP client Time Zone Setting You can maintain the system time by synchronizing with a public time server over the Internet Current Time Yr 2009 Mon 1 Day 27 Hril Mn 47 Secs Time Zone Select GMT 08 00 Pacific Time US amp Canada Tijuana Enable NTP client update Automatically Adjust Daylight Saving N
17. TP server 192 5 41 41 North America A f i i J Manual IP Setting LAN Interface Setup This page is used to configure local area network IP address and subnet mask LAN Interface Setup This page is used to configure the parameters for local area network which connects to the LAN port of your Access Point Here you may change the setting for IP addresss subnet mask DHCP etc IP Address 192 168 0 254 Subnet Mask 255 255 0 0 Default Gateway 0 0 0 0 DHCP Server DHCP Client Range 192 168 0 100 192 168 0 200 Static DHCP Domain Name 602 1d Spanning Tree Disabled Clone MAC Address g00000000000 Item Description IP Address Fill in the address of LAN interfaces of this WLAN Access Point Point packets mode of wireless Access Point range of IP addresses client with DHCP function set will be re assigned an IP address from the range Show Client Click to open the active DHCP Client Table window that shows the active clients with their assigned IP address MAC address and time expired information Server mode only Static DHCP Select enable or disable the Static DHCP function from pull down menu Server mode only address Server mode only optional field from pull down menu Clone MAC Address Fill in the MAC address that is the MAC address to be cloned configuration setting configuration setting WAN Interface Setup This page is used to configure W
18. These settings should not be changed unless you know what effect the changes will have on your WLAN Broadband Router Wireless Advanced Settings These settings are only for more technically advanced users who have a sufficient knowledge about wireless LAN These settings should not be changed unless you know what effect the changes will have on your Access Point Fragment Threshold 2546 256 2346 RTS Threshold 2347 0 2347 Beacon Interval 100 20 1024 ms Preamble Type Long Preamble Short Preamble IAPP Enabled Disabled Protection Enabled Disabled Aggregation Enabled Disabled Short GI Enabled Disabled WLAN Partition O Enabled Disabled RF Output Power 100 O70 Oso O3 O15 Item Description Fragment Threshold Set the data packet fragmentation threshold value Toemen Tweed GE be wntten between 258 and 2346 yes o RTS Threshold Set the RTS Threshold value can be written between 0 Ee aaao ne n pe wrmen beeen 0 Beacon Interval Set the Beacon Interval value can be written between tenme Er o n oe wren pemean Preamble Type Click to select the Long Preamble or Short Preamble support on the wireless data packet transmission IAPP Click to enable or disable the IAPP function Protection Protection is for neighboring 802 11b wireless network Select disable to reduce the adverse affect of legacy wireless network 802 11n performance This option is available only when 802 11 mode
19. able IPsec pass through on Click the checkbox to enable IPSec packet pass VPN connection through through Enable L2TP pass through on VPN connection Click to select Static IP support on WAN interface There are IP address subnet mask and default gateway settings need to be done in the IP address for it interface fill in the subnet mask for it If you select the Static IP support on WAN interface fill in the default gateway for WAN interface out going data packets 19 configuration setting the previous configuration setting DHCP Client WAN Interface Setup This page is used to configure the parameters for Internet network which connects to the WAN port of your Access Point Here you may change the access method to static IP DHCP PPPoE PPTP or L2TP by click the item value of WAN Access type WAN Access Type DHCP Client Host Name MTU Size 1492 1400 1492 bytes Attain DNS Automatically Set DNS Manually DNS 1 DNS 2 DNS 3 Clone MAC Address 000000000000 C Enable uPNP Enable IGMP Proxy C Enable Ping Access on WAN C Enable Web Server Access on WAN C Enable IPsec pass through on YPN connection C Enable PPTP pass through on VPN connection C Enable L2TP pass through on VPN connection Item Description address assigned automatically from a DHCP server is empty 1400 Attain DNS Automatically Click to select getting DNS address for DHCP support Please select Set DNS Man
20. abled MyWLAN linux Wlan RIL8186 VPN GW Sales Tekom_Office alex MyWLAN 00 02 72 00 81 86 00 02 72 f1 02 ad O0 e0 4 81 86 23 00 02 72 04 68 92 00 02 72 00 93 fb d6 4c fc 0d 2a d4 00 02 72 85 15 99 11 B G 6 B 11 B G 11 B 9 B 1 B 11 B AP AP AP AP AP Ad hoc AP 76 66 53 35 32 32 15 SSID It shows the SSID of AP BSSID It shows BSSID of AP It show the current channel of AP occupied Type It shows which type of connection to be connect infrastructure AP or ad hoc Encrypt It shows the encryption status Signal It shows signal strength expressed in percentage of current AP Click the Refresh button to re scan site survey on the screen Click the Connect button to establish connection This page allows you to change the setting for WPS Wi Fi Protected Setup Using this feature could let your wireless client automatically synchronize its setting and connect to the Access Point in a minute without any hassle Wi Fi Protected Setup This page allows you to change the setting for WPS Wi Fi Protected Setup Using this feature could let your wireless client automically syncronize its setting and connect to the Access Point in a minute without any hassle Disable WPS WPS Status Configured UnConfigured Reset to UnConfiqured Self PIN Number 08904089 Push Button Configuration start PBC Client PIN Number Start PIN Item Description Self PIN Number F
21. allowed to link to this WLAN Broadband Router WDS Security Setup Requirement Set Wireless gt Basic Settings gt Mode gt AP WDS This page is used to configure the wireless security between APs WDS Security Setup This page allows you setup the wireless security for WDS When enabled you must make sure each WDS device has adopted the same encryption algorithm and Key Encryption None WEP Key Format WEP Key Pre Shared Key Format Pre Shared Key Apply Changes Close Reset 14 WDS AP Table This page is used to show WDS statistics WDS AP Table This table shows the MAC address transmission recerption packet counters and state information for each configured WDS AP 00 02 72 81 86 0a 00 02 72 81 86 0b Item Tx Packets It shows the statistic count of sent packets on the pre e ee Tx Errors It shows the statistic count of error sent packets on TES O ewr aaae Or Rx Packets It shows the statistic count of received packets on the e a een Tx Rate Mbps It shows the wireless link rate within WDS Click to refresh the statistic counters on the screen Click to close the current window Site Survey pai l4 Description This page is used to scan and connect nearby APs when operate at client mode Wireless Site Survey This page provides tool to scan the wireless network If any Access Point or IBSS is found you could choose to connect it raanually when client mode is en
22. currently Encryption It shows the status of encryption function BSSID It shows the BSSID address of the WLAN Broadband Router BSSID is a six byte address Associated Clients It shows the number of connected clients or stations PCs TCP IP configuration Attain IP Protocol It shows type of connection Broadband Router WLAN Broadband Router interfaces outgoing data packets DHCP Server MAC Address It shows the MAC address of LAN interfaces of WAN configuration Attain IP Protocol It shows how the WLAN Broadband Router gets the IP address The IP address can be set manually to a fixed one or set dynamically by DHCP server or attain IP by PPPoE PPTP connection Broadband Router Subnet Mask It shows the IP subnet mask of WAN interface of Default Gateway It shows the default gateway setting for WAN DNS1 DNS2 DNS3 MAC Address It shows the MAC address of WAN interface of WLAN Broadband Router Setup Wizard This page guides you to configure wireless broadband router for first time setup Wizard The setup wizard will guide you to configure access point for first time Please follow the setup wizard step by step Welcome to Setup Wizard The Wizard will guide you the through following steps Begin by clicking on Next Setup Operation Mode Choose your Time Zone setup LAN Interface Setup WAN Interface Wireless LAN Setting Wireless Security Setting Operation Mode This page followed by
23. e GEC CK The Power Networking Company em F T 7 E E E O r r A A if F NN N A DAAC N Pe J Ge NS ka A b 802 11b g n High Power Wireless AP router w Built in Amplifier Booster User Manual Part GT APN Before Start to Configure The WLAN Broadband Router is delivered with the following factory default parameters on the Ethernet LAN interfaces Default IP Address 192 168 1 254 Default IP subnet mask 255 255 255 0 WEB login User Name lt empty gt WEB login Password lt empty gt The device has three operation modes Gateway Bridge WISP The default IP addresses for the device are 192 168 1 254 so you need to make sure the IP address of your PC is in the same subnet as the device such as 192 168 1 X It will take about 55 seconds to complete the boot up sequence after power on Prepare your PC to configure the WLAN Broadband Router For OS of Microsoft Windows 95 98 Me 1 Click the Start button and select Settings then click Control Panel The Control Panel window will appear Note Windows Me users may not see the Network control panel If so select View all Control Panel options on the left side of the window 2 Move mouse and double click the right button on Network icon The Network window will appear 3 Check the installed list of Network Components If TCP IP is not installed click the Add button to install it otherwise go to step 6 4 Select Protocol
24. e private local network behind your Gateway s NAT firewall Cl Enable Port Forwarding IP Address Protocol Both Port Range Comment Current Port Forwarding Table Delete Selected Delete All Item Description Local IP Address To forward data packets coming from WAN to a Protocol specific IP address that hosted in local network behind Port Range the NAT firewall fill in the IP address protocol port Comment range and your comments The Protocol can be TCP UDP or Both The Port Range for data transmission Comments let you know about whys to allow data packets forward to the IP address and port number Apply Changes Click the Apply Changes button to register the IP e i ONA Reset Click the Reset button to abort change and recover aa e Delete Selected Click to delete the selected IP address and port number that will be removed from the port forwarding list Delete All Click to delete all the registered entries from the A e a the previous configuration setting 29 Firewall URL Filtering URL Filtering is used to restrict users to access specific websites in internet URL Filtering URL filter is used to deny LAN users from accessing the internet Block those URLs which contain keywords listed below Enable URL Filtering URL Address Current Filter Table Description Enable URL Filtering Click to enable the URL Filtering function URLAddress Add one URL address Apply Change
25. ect PPPoE support on WAN interface There are user name password connection type and idle time settings need to be done If you select the PPPoE support on WAN interface fill in the user name and password to login the PPPoE server If you select the PPPoE support on WAN interface fill in the user name and password to login the PPPoE server Select the connection type from pull down menu There are Continuous Connect on Demand and Manual three types to select Continuous connection type means to setup the connection through PPPoE protocol whenever this WLAN Broadband Router is powered on Connect on Demand connection type means to setup the connection through PPPoE protocol whenever you send the data packets out through the WAN interface there are a watchdog implemented to close the PPPoE connection while there are no data sent out longer than the idle time set Manual connection type means to setup the connection through the PPPoE protocol by clicking the Connect button manually and clicking the Disconnect button manually Idle Time If you select the PPPoE and Connect on Demand connection type fill in the idle time for 21 auto disconnect function Value can be between 1 and 1000 minutes MTU Size Fill in the mtu size of MTU Size The default value is 1400 Attain DNS Automatically Click to select getting DNS address for DHCP support Please select Set DNS Manually if the DHCP support is selected Clone MAC Address Fi
26. egistered entries from the pene pete me the previous configuration setting Firewall IP Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network IP Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network Enable IP Filtering Loal IP Address Protocol Both Comment Current Filter Table LocalIPAddress Protocol Comment Select Palee Saeed Delete All Item Description Enable IP Filtering Click to enable the IP filtering security function Local IP Address Protocol To restrict data transmission from local network on Comments certain IP addresses fill in the IP address and the protocol also put your comments on it The Protocol can be TCP UDP or Both Comments let you know about whys to restrict data from the IP address address to IP filtering list the previous configuration setting removed from the IP filtering list IP filtering list the previous configuration setting 27 Firewall MAC Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful i
27. ending station The receiving station then returns a frame that indicates whether it recognizes the sending station Under shared key authentication each wireless station is assumed to have received a secret shared key over a secure channel that is independent from the 802 11 wireless network communications channel 9 What is WEP An optional IEEE 802 11 function that offers frame transmission privacy similar to a wired network The Wired Equivalent Privacy generates secret shared encryption keys that both source and destination stations can use to alert frame bits to avoid disclosure to eavesdroppers WEP relies on a secret key that is shared between a mobile station e g a laptop with a wireless Ethernet card and an access point i e a base station The secret key is used to encrypt packets before they are transmitted and an integrity check is used to ensure that packets are not modified in transit 10 What is Fragment Threshold The proposed protocol uses the frame fragmentation mechanism defined in IEEE 802 11 to achieve parallel transmissions A large data frame is fragmented into several fragments each of size equal to fragment threshold By tuning the fragment threshold value we can get varying fragment sizes The determination of an efficient fragment threshold is an important issue in this scheme If the fragment threshold is small the overlap part of the master and parallel transmissions is large This means the Spatial reuse
28. erver typically one that supports RADIUS and the selected EAP authentication protocol will be added to the network 16 What is WPA2 It is the second generation of WPA WPA2 is based on the final IEEE 802 111 amendment to the 802 11 standard 17 What is 802 1x Authentication 802 1x is a framework for authenticated MAC level access control defines Extensible Authentication Protocol EAP over LANs WAPOL The standard encapsulates and leverages much of EAP which was defined for dial up authentication with Point to Point Protocol in RFC 2284 Beyond encapsulating EAP packets the 802 1x standard also defines EAPOL messages that convey the shared key information critical for wireless security 18 What is Temporal Key Integrity Protocol TKIP The Temporal Key Integrity Protocol pronounced tee kip is part of the IEEE 802 11i encryption standard for wireless LANs TKIP is the next generation of WEP the Wired Equivalency Protocol which is used to secure 802 11 wireless LANs TKIP provides per packet key mixing a message integrity check and a re keying mechanism thus fixing the flaws of WEP 19 What is Advanced Encryption Standard AES Security issues are a major concern for wireless LANs AES is the U S government s next generation cryptography algorithm which will replace DES and 3DES 42 20 What is Inter Access Point Protocol IAPP The IEEE 802 11f Inter Access Point Protocol IAPP supports Access Point
29. g is useful for networks with many clients With many clients and a high network load there will be many more collisions By lowering the RTS threshold there may be fewer collisions and performance should improve Basically with a faster RTS threshold the system can recover from problems faster RTS packets consume valuable bandwidth however so setting this value too low will limit performance 12 What is Beacon Interval In addition to data frames that carry information from higher layers 802 11 include management and control frames that support data transfer The beacon frame which is a type of management frame provides the heartbeat of a wireless LAN enabling stations to establish and maintain communications in an orderly fashion Beacon Interval represents the amount of time between beacon transmissions Before a station enters power save mode the station needs the beacon interval to know when to wake up to receive the beacon and learn whether there are buffered frames at the access point 13 What is Preamble Type There are two preamble types defined in IEEE 802 11 specification A long preamble basically gives the decoder more time to process the preamble All 802 11 devices support a long preamble The short preamble is designed to improve efficiency for example for VoIP systems The difference between the two is in the Synchronization field The long preamble is 128 bits and the short is 56 bits 14 What is SSI
30. ge The connection type can be setup in WAN page by using PPPOE DHCP chent PPTP client or static IP Item Description Gateway Traditional gateway configuration It always connects internet via ADSL Cable Modem LAN interface WAN interface Wireless interface NAT and Firewall modules are applied to this mode Firewall and all router s functions are not supported bridge mode Wireless interface can do all router s functions configuration setting previous configuration setting Wireless Basic Settings This page is used to configure the parameters for wireless LAN clients that may connect to your Broadband Router Here you may change wireless encryption settings as well as wireless network parameters Wireless Basic Settings This page is used to configure the parameters for wireless LAN clients which may connectto your Access Point Here you may change wireless encryption settings as well as wireless network parameters _ Disable Wireless LAN Interface Band 2 4 GHz B G N v Mode AP v Network Type Infrastructure v SSID 802 11b m SSID Channel Width 20MHz v Control Sideband Upper Channel Number 6 v Broadcast SSID Enabled WMM Enabled Data Rate Auto w Associated Clients Show Active Clients Enable Mac Clone Single Ethernet Client C Enable Universal Repeater Mode Acting as AP and client simultaneoulh SSID of Extended Interface _ Item Description Disable Wire
31. ill in the PIN Number of AP to register the wireless C O a Push Button Configuration The Start PBC button provides tool to scan the wireless network If any Access Point or IBSS is found you could connect it automatically when client join PBC mode configuration setting previous configuration setting Client PIN Number Fill in the Client PIN Number from your Client sites 16 LAN Interface Setup This page is used to configure the parameters for local area network that connects to the LAN ports of your WLAN Broadband Router Here you may change the setting for IP address subnet mask DHCP etc LAN Interface Setup This page is used to configure the parameters for local area network which connects to the LAN port of your Access Point Here you may change the setting for IP addresss subnet mask DHCP etc IP Address 192 168 0 254 Subnet Mask 255 255 0 0 Default Gateway 0 0 0 0 DHCP Server yi DHCP Client Range 192 168 0 100 192 168 0 200 Show Client Static DHCP Set Static DHCP Domain Name 802 1d Spanning Tree Disabled Mi Clone MAC Address OOo000000000 Apply Changes Reset Item Description Access Point Access Point going data packets operation mode of wireless Access Point DHCP Client Range Fill in the start IP address and end IP address to allocate a range of IP addresses client with DHCP function set will be assigned an IP address from the range Show Client Click to open
32. ke the Ethernet does To do this you must set these APs in the same channel and set MAC address of other AP that you want to communicate with in the table and then enable the WDS WDS Settings Wireless Distribution System uses wireless media to communicate with other APs like the Ethernet does To do this you must set these APs in the same channel and set MAC address of other APs which you want to communicate with in the table and then enable the WDS Enable WDS MAC Address Data Rate Auto Comment Apply Ct oet Security show Statistics Current WDS AP List Delete Selected Delete All Reset Item Description Enable WDS Click the Disabled Allow Listed or Deny Listed of drop down menu choose wireless access control mode This is a security control function only those clients registered in the access control list can link to this WLAN Broadband Router WLAN Broadband Router access capability Data Rate Select transmission data rate from pull down menu Data rate can be auto selected 1Mbps to 54Mbps or MCS Fill in the comments for the registered client 13 to new configuration setting the previous configuration setting Set Security Click button to configure wireless security like B WEP 64bits WEP 128bits WPA TKIP WPA2 AES or None removed from the wireless distribution system distribution system allowed list the previous configuration setting It shows the registered clients that are
33. l in the IP address of Domain Name Server 2 DNS 3 Fill in the IP address of Domain Name Server 3 Clone MAC Address Fill in the MAC address that is the MAC address to be cloned Enable uPNP Click the checkbox to enable uPNP function Enable IGMP Proxy Click the checkbox to enable IGMP proxy Enable Ping Access on WAN Click the checkbox to enable WAN IGMP response Enable Web server Access on Click the checkbox to enable web configuration from Enable IPsec pass through on Click the checkbox to enable IPSec packet pass Enable PPTP pass through on Click the checkbox to enable PPTP packet pass Enable L2TP pass through on Click the checkbox to enable L2TP packet pass configuration setting the previous configuration setting L2tP Use Layer 2 Tunneling Protocol L2TP if your ISP uses an L2TP connection Your ISP will provide you with a username and password 24 WAN Interface Setup This page is used to configure the parameters for Internet network which connects to the WAN port of your Access Point Here you may change the access method to static IP DHCP PPPoE PPTP or L2TP by click the item value of WAN Access type WAN Access Type L2TP IP Address 0 0 0 0 Subnet Mask 0 0 0 0 Server IP Address 0 0 0 0 User Name Password Connection Type Continuous Connect Disconnect Idle Time 5 1 1000 minutes MTU Size 1412 1400 1460 bytes Attain DNS Automatically Set DNS Manually DNS 1 DNS 2 DNS 3 Clone MAC Add
34. less LAN Interface Click on to disable the wireless LAN data transmission Click to select 2 4GHz B 2 4GHz G 2 4GHz B G Mode Click to select the WLAN AP Client WDS AP WDS wireless mode Network Type While network is selected to be client Click to select e a S SSID It is the wireless network name The SSID can be ee aime eeso 802 11n band only Control Sideband Select the sideband with upper or lower for channel a at aonane Peer erower anne Channel Number Select the wireless communication channel from pull down menu Click to enable or disable the SSID broadcast function Data Rate Select transmission data rate from pull down menu Omens Data rate ean be auto select IM 19 SAMs or eS Associated Clients Click the Show Active Clients button to open Active Wireless Client Table that shows the MAC address transmit packet receive packet and transmission rate for each associated wireless client Enable Mac Clone Single Take Laptop NIC MAC address as wireless client Ethernet Client MAC address Client Mode only 10 Enable Universal Repeater Click to enable Universal Repeater Mode Acting as AP Mode and client simultaneously in this mode SSID of Extended Interface Assign SSID when enables Universal Repeater Mode configuration setting previous configuration setting Wireless Advanced Settings These settings are only for more technically advanced users who have a sufficient knowledge about wireless LAN
35. ll in the MAC address that is the MAC address to be cloned Enable uPNP Click the checkbox to enable uPNP function Enable IGMP Proxy Click the checkbox to enable IGMP proxy Enable Ping Access on WAN Click the checkbox to enable WAN IGMP response WAN WAN side VPN connection through VPN connection through VPN connection through configuration setting the previous configuration setting 22 PPTP WAN Interface Setup This page is used to configure the parameters for Internet network which connects to the WAN port of your Access Point Here you may change the access method to static IP DHCP PPPoE PPTP or L2TP by click the item value of WAN Access type WAN Access Type EPI IP Address 0 0 0 0 Subnet Mask 0 0 0 0 Server IP Address 0 0 0 0 User Name Password Connection Type Continuous Connect Disconnect Idle Time 5 1 1000 minutes MTU Size 1412 1400 1460 bytes Request MPPE Encryption H Request MPPC Compression Attain DNS Automatically Set DNS Manually DNS 1 DNS 2 DNS 3 Clone MAC Address 000000000000 Enable uPNP Enable IGMP Proxy Enable Ping Access on WAN Enable Web Server Access on WAN Enable IPsec pass through on VPN connection Enable PPTP pass through on VPN connection Enable L2TP pass through on VPN connection Apply Changes Reset Allow user to make a tunnel with remote site directly to secure the data transmission among the connection User can use embedded
36. n securing or restricting your local network MAC Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network Enable MAC Filtering MAC Address Comment Current Filter Table Delete Selected Item Description Enable MAC Filtering Click to enable the MAC filtering security function MAC Address Comments To restrict data transmission from local network on certain MAC addresses fill in the MAC address and your comments on it Comments let you know about whys to restrict data from the MAC address MAC address to MAC filtering list the previous configuration setting removed from the MAC filtering list MAC filtering list the previous configuration setting 28 Firewall Port Forwarding Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall These settings are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind your Gateway s NAT firewall Port Forwarding Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall These settings are only necessary if you wish to host some sort of server like a web server or mail server on th
37. ne gaming experience by ensuring that your game traffic is prioritized over other network traffic such as FTP or Web QoS Entries in this table improve your online gaming experience by ensuring that your is prioritized over other network traffic such as FTP or Web O0 Enable QoS Automatic Uplink Speed Manual Uplink Speed Kbps 100 Automatic Downlink Speed Manual Downlink Speed Kbps 100 QoS Rule Setting Address Type Local IP Address MAC Address Mode Guaranteed minimum bandwidth Uplink Bandwidth Kbps oT Downlink Bandwidth Kbps Comment Apply Changes si Reset Current QoS Rules Table Local IP MAC Mode Uplink Downlink Address Address Bandwidth Bandwidth Comment Sel Delete Selected Delete All Reset Item Description Enable QoS Click to enable the QoS function control uplink bandwidth capacity Kbps bandwidth control Address Type Select IP address or MAC address 31 bandwidth or Restricted maximum bandwidth Downlink Bandwidth Enter downlink bandwidth in Kbps Give a definition to the setting Apply Changes Click the Apply Changes button to save the settings Reset Click the Reset button to abort change and recover the previous configuration setting Local IP Address List LAN IP address that is controlled MAC Address List MAC address that is controlled Mode List control type that is controlled Guaranteed minimum bandwidth or Restricted maximum bandwidth
38. o apply no web management login control Click the Apply Changes button to complete the new configuration setting Reset Click the Reset button to abort change and recover the previous configuration setting 37 Frequently Asked Questions FAQ 1 What and how to find my PC s IP and MAC address IP address is the identifier for a computer or device on a TCP IP network Networks using the TCP IP protocol route messages based on the IP address of the destination The format of an IP address is a 32 bit numeric address written as four numbers separated by periods Each number can be zero to 255 For example 191 168 1 254 could be an IP address The MAC Media Access Control address is your computer s unique hardware number On an Ethernet LAN it s the same as your Ethernet address When you re connected to the Internet from your computer or host as the Internet protocol thinks of it a correspondence table relates your IP address to your computer s physical MAC address on the LAN To find your PC s IP and MAC address Open the Command program in the Microsoft Windows Type in ipconfig all then press the Enter button Your PC s IP address is the one entitled IP Address and your PC s MAC address is the one entitled Physical Address 2 What is Wireless LAN A wireless LAN WLAN is a network that allows access to Internet without the need for any wired connections to the user s machine 3 What are
39. ood ICE TCE UDF PortScan ICME Srvact If Land If Spoof IE Tear iirop King Of Death TCE Scan TCE Syn Wath Data UDF Bomb UDF Echo Chargen Enable Source IP Blocking i Block time set Apply Changes Item Description 0 Enable DoS Prevention Click the checkbox to enable DoS prevention Whole System Flood Enable and setup prevention in details Per Source IP Flood Select ALL Click the checkbox to enable all prevention items Clear ALL Click the checkbox to disable all prevention items Apply Changes Click the Apply Changes button to save above settings 35 Management Log This page is used to configure the remote log server and shown the current log System Log This page can be used to set remote log server and show the system log C Enable Log system all wireless DoS Enable Remote Log Log Server IP Address Apply Changes Item Description Dos Management Upgrade Firmware This page allows you upgrade the Access Point firmware to new version Please note do not power off the device during the upload because it may crash the system Upgrade Firmware This page allows you upgrade the Access Point firmware to new version Please note do not power off the device during the upload because it may crash the system Select File Item Description firmware image file Click the Upload button to update the selected web firmware image to the WLAN Broadband Router previo
40. register to a server machine with one identified MAC address Since that all the clients will communicate outside world through the WLAN Broadband Router so have the cloned MAC address set on the WLAN Broadband Router will solve the issue 25 What is DDNS DDNS is the abbreviation of Dynamic Domain Name Server It is designed for user own the DNS server with dynamic WAN IP address 26 What is NTP Client NTP client is designed for fetching the current timestamp from internet via Network Time protocol User can specify time zone NTP server IP address 43 27 What is VPN VPN is the abbreviation of Virtual Private Network It is designed for creating point to point private link via shared or public network 28 What is IPSEC IPSEC is the abbreviation of IP Security It is used to transferring data securely under VPN 44
41. ress 000000000000 Enable uPNP Enable IGMP Proxy Enable Ping Access on WAN Enable Web Server Access on WAN Enable IPsec pass through on VPN connection Enable PPTP pass through on VPN connection Enable L2TP pass through on VPN connection Apply Changes Reset Item Description L2TP Allow user to make a tunnel with remote site directly em to secure the data transmission among the connection User can use embedded PPTP client supported by this router to make a VPN connection Enter L2TP service username provided by your ISP Enter L2TP service password provided by your ISP Connection Type Select the connection type from pull down menu There are Continuous Connect on Demand and Manual three types to select Continuous connection type means to setup the connection through L2TP protocol whenever this WLAN Broadband Router is powered on Connect on Demand connection type means to setup the connection through L2TP protocol whenever you send the data packets out through the WAN interface there are a watchdog implemented to close the L2TP connection while there are no data sent out longer than the idle time set Manual connection type means to setup the connection through the L2TP protocol by clicking the Connect button manually and clicking the Disconnect button manually Idle Time The amount of time of inactivity before the device will disconnect your L2TP session MTU Size Change the MTU size that your ISP provided The es
42. s Click the Apply Changes button to save settings Reset Click the Reset button to abort change and recover a TA Delete Selected Click to delete the selected URL address that will be C emeved fem he UR Flteingist Delete All Click to delete all the registered entries from the URL eee sterngnst ne ENE enes tom the UR Reset Click the Reset button to abort change and recover et apres entguaton setting Firewall DMZ A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network Typically the DMZ host contains devices accessible to Internet traffic such as Web HTTP servers FTP servers SMTP e mail servers and DNS servers DMZ A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network Typically the DMZ host contains devices accessible to Internet traffic such as Web HTTP servers FTP servers SMTP e mail servers and DNS servers Cl Enable DMZ DMZ Host IP Address 30 Enable DMZ Click to enable the DMZ function DMZ Host IP Address To support DMZ in your firewall design fill in the IP address of DMZ host that can be access from the WAN interface Apply Changes Click the Apply Changes button to register the IP address of DMZ host Reset Click the Reset button to abort change and recover the previous configuration setting QoS Entries in this table improve your onli
43. ted Clients Show Active Clients Enable Mac Clone Single Ethernet Client Enable Universal Repeater Mode Acting as AP and client simultaneouly SSID of Extended Interface Wireless Security Setup This page is used to configure wireless security Wireless Security Setup This page allows you setup the wireless security Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network Select SSID Root AP 802 11bgn SSID Apply Changes Encryption Disable 802 1x E Authentication Operation Mode This page is used to configure which mode wireless broadband router acts Operation Mode You can setup different modes to LAN and WLAN interface for NAT and bndging function KNEES In this mode the device is supposed to connect to internet via ADSL Cable Modem Gateway PP The NAT is enabled and PCs in LAN ports share the same IP to ISP through WAN port The connection type can be setup in WAN page by using PPPOE DHCP client PPTP chent or static IP Bridge In this mode all ethernet ports and wireless interface are bridged together and NAT function is disabled All the WAN related function and firewall are not supported Wireless ISP In this mode all ethernet ports are bridged together and the wireless chent will connect to ISP access pomt The NAT is enabled and PCs in ethemet ports share the and connect to the ISP AP in Site Survey pa
44. the Microsoft Windows CD to complete the installation Close and go back to Network dialog box after the TCP IP installation 6 Select TCP IP and click the properties button on the Network dialog box 7 Select Specify an IP address and type in values as following example IP Address 192 168 1 1 any IP address within 192 168 1 1 to 192 168 1 253 is good to connect the Wireless LAN Access Point IP Subnet Mask 255 255 255 0 8 Click OK to completes the IP parameters setting For OS of Microsoft Windows NT 1 Click the Start button and select Settings then click Control Panel The Control Panel window will appear Move mouse and double click the right button on Network icon The Network window will appear Click Protocol tab from the Network window Check the installed list of Network Protocol window If TCP IP is not installed click the Add button to install it otherwise go to step 6 Select Protocol in the Network Component Type dialog box and click Add button Select TCP IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP IP protocol it may need the Microsoft Windows CD to complete the installation Close and go back to Network dialog box after the TCP IP installation Select TCP IP and click the properties button on the Network dialog box Select Specify an IP address and type in values as following example IP Address 192 168 1 1 any IP address within 192 168 1 1 to
45. ually if the DHCP support is selected Clone MAC Address Fill in the MAC address that is the MAC address to be cloned Enable uPNP Click the checkbox to enable uPNP function Enable IGMP Proxy Click the checkbox to enable IGMP proxy Enable Ping Access on WAN Click the checkbox to enable WAN IGMP response WAN WAN side VPN connection through VPN connection through VPN connection through configuration setting 20 Reset Click the Reset button to abort change and recover the previous configuration setting PPPoE Item PPPoE Service Name Fill in the service name of Service Name The default value is empty Connection Type WAN Interface Setup This page is used to configure the parameters for Intemet network which connects to the WAN port of your Access Point Here you may change the access method to static IP DHCP PPPoE PPTP or L2TP by click the item value of WAN Access type WON Access Type User Name Password Service Name Connection Type Contre Comert Idle Time so ooo 1 1000 minutes MTU Size itt 1360 1492 bytes attain ONS Automatically Set DNS Manually DNS 4 i DNS 2 DNS 3 Clone MAC Address 000000000000 C Enable uPNP Enable IGMP Proxy O Enable Ping Access on WAN a Enable Web Server Access on WAN d Enable IPsec pass through on VPN connection O Enable PPTP pass through on VPN connection d Enable L2TP pass through on VPN connection Description Click to sel
46. us configuration setting Management Save Reload Settings This page allows you save current settings to a file or reload the settings from the file that was saved previously Besides you could reset the current configuration to factory default Save Reload Settings This page allows you save current settings to a file or reload the settings from the file which was saved previously Besides you could reset the current configuration to factory default Save Settings to File Load Settings from File Upload Reset Settings to Default Item Description Save Settings to File Click the Save button to download the configuration Ginga e a Load Settings from File Click the Browse button to select the configuration files then click the Upload button to update the selected configuration to the WLAN Broadband Router Reset Settings to Default Click the Reset button to reset the configuration parameter to factory defaults Management Password Setup This page is used to set the account to access the web server of Access Point Empty user name and password will disable the protection Password Setup This page is used to set the account to access the web server of Access Point Empty user name and password will disable the protection User Name New Password Confirmed Password Item Description the password again for confirmation purpose Apply Changes Clear the User Name and Password fields to empty means t
47. work that connects to the WAN port of your WLAN Broadband Router Here you may change the access method to Static IP DHCP PPPoE or PPTP by click the item value of WAN Access Type Static IP WAN Interface Setup This page is used to configure the parameters for Internet network which connects to the WAN port of your Access Point Here you may change the access method to static IP DHCP PPPoE PPTP or L2TP by click the iter value of WAN Access type WAN Access Type Static IP IP Address 192 168 1 1 Subnet Mask 255 255 0 0 Default Gateway 192 168 1 254 MTU Size 1500 1400 1500 bytes DNS 1 DNS 2 DNS 3 Clone MAC Address O00000000000 C Enable uPNP Enable IGMP Proxy Enable Ping Access on WAN C Enable Web Server Access on WAN _ Enable IPsec pass through on VPN connection Enable PPTP pass through on VPN connection C Enable L2TP pass through on VPN connection Static IP Default Gateway MTU Size Fill in the mtu size of MTU Size The default value is 1400 DNS 1 Enter the IP address of Domain Name Server 1 DNS 2 Enter the IP address of Domain Name Server 2 DNS 3 Enter the IP address of Domain Name Server 3 Clone MAC Address Enter the MAC address that is the MAC address to be cloned Enable uPNP Click the checkbox to enable uPNP function Enable IGMP Proxy Click the checkbox to enable IGMP proxy Enable Ping Access on WAN Click the checkbox to enable WAN IGMP response WAN WAN side En
Download Pdf Manuals
Related Search