DeltaPoint Instruction Manual
Contents
1. 3V Lithium battery CR 2032 e 1 Protective cover e 2 M4 x 0 7mm Torx head screws for installing the sight on the mounting plate e 2 6 48x 210 Torx screws for installing the S amp W Classic base e 3 Torx Set Screws e 1 Torx T 5 wrench e 1 Torx T 15 wrench e Cross Slot Mount e 10 Mount Bases with dovetails Mount Base 1B Dovetail 1A Beretta 92 96 90 TWO Taurus PT99 Mount Base 2B Dovetail 2A 1911 Standard Mount Base 3B Dovetail 3A Glock Standard Frame will not fit Large Frame 45acp 45 GAP 10mm models Mount Base 4B Dovetail 4A Sig Sauer P226 Mount Base 5B Dovetail 5A Springfield XD Mount Base 6B Dovetail 6A CZ 75 Mount Base 7B Dovetail 7A HK HK P2000 Mount Base 8B Dovetail 8A Kimber Fixed Adjustable Mount Base 9B Dovetail 9A Smith amp Wesson M amp P Mount Base 10B Insert 10A Smith amp Wesson Classic e Operating Instructions Cautions amp Warnings Check to ensure that the magazine of the firearm has been removed or emptied that the action is open and that there is not a round in the chamber Only after double checking the firearm verifying it is empty and safe should you proceed with the installation of the Delta Point Do not look directly into the sun light arcs or other high intensity light sources Keep away from children Adjustment lock screws are loosened at the factory and your firearm should not be fired with the2. DeltaPoint attached until these screws are tighened to 4 inch pounds Start Up The unit operates with one commercially available 3V Lithium battery CR 2032 only Insert the battery into the receptacle located on the underside of the housing oriented so that the positive pole on the battery label is visible Keep the contact surface clean of dirt and corrosion cleaning with alcohol if necessary If you intend to use the DeltaPoint in a wet environment we recommend coating the battery on all sides with petroleum jelly or other electronics grade lubricant protectant to prevent battery corrosion Battery Installation Remove the two screws holding the DeltaPoint to the base and turn the sight upside down Place the Torx wrench or a screwdriver in the notch and gently pry the battery loose Insert a new battery as described earlier The precision pins eliminate the need for any re adjustment Installation Installation on most handguns requires the use of one of the included mount bases Leupold recommends utilizing a qualified gunsmith to press remove the rear sight from your handgun Once the rear sight has been removed the appropriate dovetail replaces the rear sight with the part number facing up Some installations Kimber Smith amp Wesson M amp P require the use of the included set screws to be placed in the dovetail to hold it in place and the M4 x 0 7mm Torx screws will fasten into the dovetail plate extension T
3. IL IE U P OLD AMERICA S OPTICS AUTHORITY Leupold DeltaPoint Reflex Sight Mounting amp Operation Instructions Operating Instructions For optimum performance and to prevent damage to this precision instrument carefully follow all instructions Features e DiamondCoat scratch resistant aspheric lens for maximum field of view brightness and resolution e Proprietary Intelligent Brightness Control IBC Motion activated on off illumination feature Patent Pending e Extremely durable ultra light magnesium housing e Small size and weight e Unlimited eye relief e For handguns rifles and shotguns e Wide field of view e Blackened lens edges Specifications e Magnification 1 0x e Sight window 26mm x 19mm 1 02 x 0 75 e Elevation adjustment range 60 MOA e Windage adjustment range 60 MOA e 60 MOA per revolution of adjustment e Subtension of the aiming point 3 5 MOA Dot 7 5 MOA inscribed Delta e Operating Temperature Range 20 F to 120 F 29 C to 49 C e Storage Temperature Range 40 F to 160 F 40 C to 71 C e Power Supply 3V with one CR 2032 Lithium battery e Dimensions LxWxH 1 61 x 1 18 x 1 06 41mm x 30mm x 27mm e Weight with battery installed 0 602 17g LED Aspheric Lens Intelligent Brightness Control Elevation Adjustment Windage Adjustment Adjustment Lock Screws Package Contents e DeltaPoint Reflex sight e 1
4. Insert Figure 2 10B Mount Base B aa Place the DeltaPoint on the mount base so that the four holes in the bottom of the DeltaPoint will align with the four short posts on the mount base and the screw holes in the sight and mount base align Figure 3 then secure the sight with the two M4x 0 7mm screws using 20 inch pounds of torque lt M4x 0 7mm Screws f Figure 3 f Reversible Cross Slot Mount Place the sight on the mount base so that the screw holes in the sight and base align also the two short corner posts on the mount align to the holes under the DeltaPoint The unit may be installed with the mount base keeper on either side Install the two M4 x 0 7mm screws and tighten to 20 inch pounds Loosen the keeper on the mount Place the mount on the rail with the cross bolt located in the desired slot Check to be sure all the clamping edges are engaged Keep a light pressure on the sight toward the muzzle as you tighten the keeper to approximately 20 inch pounds Operating Procedure Elevation and Windage Adjustment Warning Failure to loosen adjustment lock screws before making adjustments to elevation or windage screws will cause sight damage Adjustment lock screws are loosened at the factory and must be tightened to 4 inch pounds before firing separate controls for the elevation and windage adjustments are found on the top and left side of the sight Loosen the two lock screws on the back side of t
5. he corresponding mount base for your pistol is placed on top of the slide and over the dovetail with the flat part number side facing up through the slot in the base Once the dovetail and mount base have been placed on the slide the DeltaPoint is placed on top of the base The four holes in the bottom of the DeltaPoint will align with the four short posts on the mount base and secure into the dovetail using the two included M4 x 0 7mm Torx screws Figure 1 Secure the screws by applying 20 inch pounds of torque Securing these screws creates a press fit and will hold the Figure 1 M4 x 0 7mm Torx Screws Mount Base Dovetail Pistol Frame DeltaPoint firmly in place Call Leupold customer service for details specific to your handgun For rifle shotgun applications the Cross Slot Mount allows fast and easy mounting on Weaver style or Picatinny bases rails Smith amp Wesson Revolver Mount For use with Smith amp Wesson Classic pre drilled and tapped K L N amp X frame revolvers including 500 Remove the rear sight and retain the sight and all mounting hardware for future use if necessary Place the insert 10A into the mount base 10B and set both pieces on the revolver as shown below Install the two 6 48x 210 screws through the dovetail insert and into the last two tapped holes nearest the hammer in the frame of the revolver Figure 2 Tighten to 20 inch pounds 6 48x 210 Screws i 10A
6. he sight counterclockwise 1 2 turn each using the provided Torx driver Turn the D DOWN or R RIGHT screws with the provided Torx driver The windage adjustment mechanism has limit stops at both ends Before shooting make sure to tighten the lock screws to 4 inch pounds Note that the elevation adjustment downward stop is available only when the unit is installed on a mounting plate Screwing either adjustment into a stop will lock motion of the other adjustment Elevation gee Adjustment Downward Stop this screw Zeroing the Point of Impact The DeltaPoint windage and elevation screws move the point of impact 60 MOA 15 25 yds per revolution Each Mark on the adjustment screws represents about 7 5 MOA of adjustment There is 60 MOA per revolution and a total of 8 marks equals 7 5 per mark Before shooting make sure to tighten the lock screws on the rear of the DeltaPoint 4 inch pounds maximum with the provided Torx driver Caution Boresighting the DeltaPoint Verify that the magazine of the firearm has been removed or emptied and that there is not a round in the chamber Only after double checking the firearm verifying it is empty and safe should you proceed with the boresighting process Be sure to remove the Zero Point Boresighter from the the barrel prior to loading the magazine or chamber Boresighting the DeltaPoint The use of a Leupold Zero Point Boresighter is recommended w
7. hen zeroing the DeltaPoint Due to the low magnification of the DeltaPoint the grid pattern will appear relatively small To make the boresighting process easier Leupold recommends placing the eye near the DeltaPoint while making windage elevation adjustments As with any boresighting procedure be sure to follow all safety precautions prior to boresighting and make sure the boresighter has been removed from the the barrel prior to loading the magazine or chamber Power On Off The DeltaPoint will automatically power on when movement is sensed The sight will switch to sleep mode when it remains still for 5 minutes Power Saving Mode Under dark conditions the LED brightness is reduced dramatically to reduce power consumption In addition after the optic has been completely at rest for 5 minutes the sight transfers to sleep mode thus nearly eliminating all battery drain Upon any movement of the optic the system powers up the LED to the appropriate brightness in less than 1 10 of a second Placing the included rubber cover over the DeltaPoint forces the unit to operate at its Lowest ambient light setting and will remain at this level of operation until either the deltapoint is idle for 5 minutes or longer or the cover is removed and the Deltapoint adjusts to the current ambient conditions Low Battery Indicator The DeltaPoint has a unique feature that flashes the aiming point from maximum to minimum brightness when low battery power i
8. s detected The operator will have several hours of operating time in this mode before the sight is rendered inoperable without a battery change Intelligent Brightness Control The integrated control circuit adjusts the brightness of the aiming dot delta according to ambient light levels The brightness sensor on the front of the sight senses the light level in the direction of the target and modifies the intensity of the dot e delta A accordingly so that it is not overpowering in low light while remaining highly visible in bright daylight When moving from bright to dark conditions the DeltaPoint will gradually decrease the intensity of the aiming dot delta to match the dilation rate of your eye Be careful not to obstruct the sensor Clean if necessary To ensure immediate functionality the light emitting diode will remain on even in complete darkness but uses only a small amount of energy When the optic is completely Stationary for 5 minutes the circuitry switches into sleep mode It immediately powers up when any movement or vibration is detected Water Integrity Though the DeltaPoint is completely waterproof extended periods of complete immersion may result in accelerated battery depletion possibly requiring battery replacement After exposure to salty or dirty water rinse with distilled water and dry the sight Leupold Full Lifetime Guarantee Leupold warrants its products to be free from defects in materials and workman
9. ship Leupold will repair or replace at its option without charge any product or part found to be defective under normal use and service Such repair or replacement shall be the purchaser s sole and exclusive remedy under this warranty This warranty does not include normal maintenance and services and does not apply to any products or parts that have been subjected to modification misuse negligence accident improper maintenance or repair by anyone other than Leupold The electronics in your Leupold DeltaPoint Reflex sight are covered by the Leupold Electronics Warranty and are protected from defects in materials and workmanship for two years from the date of purchase In event of a need for service or repair please contact Leupold Product Service Warranty Limitation There is no other express warranty Leupold hereby disclaims any and all implied warranties including but not limited to fitness for a particular purpose Leupold shall not be liable for incidental consequential or special damages arising out of or in connection with product use or performance Leupold Product amp Technical Service If your Leupold product fails to perform in any way please contact a Leupold Product Specialist within our Product Service department to determine if the problem can be solved without sending the product to Leupold Many times the problem can be solved without sending the product to us We encourage you to contact us firs
10. t Leupold Product Service will assist you with the issue in the best and most efficient manner If we do need you to send the product in for service please include a note indicating your observations of the problem Please be detailed in your description as it will help us to expedite the service and return your product as soon as possible With our On line Product Service Status feature on our Web site you can check that your product arrived when the service began when the service was completed when it was shipped back and obtain the UPS tracking number for follow up To Reach Leupold Product Service Parcel Service Leupold Product Service 14400 NW Greenbrier Parkway Beaverton OR 97006 5791 USA Phone 7 00 a m 4 30 p m PST M F 1 800 LEUPOLD or 503 526 1400 Fax Postal Service 24 hours a day 7 days a week Leupold Product Service 503 352 7621 P O Box 688 Beaverton OR 97075 0688 USA E mail productspecialist leupold com LEUPOLD GOLDEN RING MARK 4 the Golden Ring design the circle L reticle logo design and various other marks are registered trademarks of Leupold amp Stevens Inc All marks including corporate logos and emblems are subject to Leupold s rights and may not be used in connection with any product or service that is not Leupold s or in any manner that disparages or discredits Leupold or in a manner likely to cause confusion Certain other trademarks used in connection with Leupold produc
11. ts and services are the property of their respective owners and are used with permission BOONE AND CROCKETT CLUB and BOONE AND CROCKETT are registered trademarks of the Boone and Crockett Club NWTF is a registered trademark of the National Wild Turkey Federation QDMA and QUALITY DEER MANAGEMENT are trademarks or registered trademarks of the Quality Deer Management Association RMEF and ROCKY MOUNTAIN ELK FOUNDATION are registered trademarks of the Rocky Mountain Elk Foundation ADVANTAGE TIMBER and ADVANTAGE TIMBER HD are trademarks or registered trademarks of Jordan Outdoor Enterprises Ltd MOSSY OAK BREAK UP MOSSY OAK BRUSH MOSSY OAK OBSESSION and MOSSY OAK TREESTAND are trademarks or registered trademarks of HAAS Outdoors Inc A R M S is a registered trademark of Atlantic Research Marketing Systems Inc The ARD anti reflection device is manufactured by Tenebraex Corp under the name KillFlash which is a trademark of Tenebraex Corp We reserve the right to make design and or material modifications without prior notice Copyright 2011 Leupold amp Stevens Inc All rights reserved LIEU IP OLID AMERICA S OPTICS AUTHORITY Leupold amp Stevens Inc PO Box 688 Beaverton Oregon 97075 0688 www leupold com 1 800 LEUPOLD 538 7653 Part 59828 Artwork 59827C
Download Pdf Manuals
Related Search