ThermoStat Incubater EGM-207
Contents
1. ThermoStat Incubater EGM 207 ExtraGene Inc I Overview 1 1 Model and Name of Product EGM 207 ThermoStat Incubater 1 2 Features of Product a Controlled with computer displayed in LED with program storing function and previously set parameters can automatically be restored after switching on the machine b Precise temperature control and fast temperature rise about 0 5 C second c Power Failure Resume Function enables automatic operation after power resumes d The module is with plastic case to avoid scald e Replaceable modules allow easy disman tling A user can easily replace clean and sterilize modules II Product Specification Fast change of temperature even temperature control precise temperature less than 180 seconds for temperature rising from 25 C to 99 C Average temperature rise rate 1 C 5s Temperature setting range 1 C 99 C Precision of temperature control 0 1 C Temperature evenness 0 5 C Display precision 0 1 C Time setting range 1s 99h 59min or continuous operation Heating module sample capacity 48X0 5ML 38X1 5ML 38X2ML 96X0 2ML 24X5ML or other special module made as required by client Overall dimension 277x250x132 mm Weight about 3 5Kg III Installation Installation Procedure 1 Firm and smooth table should be prepared to avoid vibration or movement of the device during 2 3 4 work Power source has separate earth line Sharing ze2. le slot module of another specification a user shall unscrew these two locking screws counterclockwise and take down the module in use and replace it with a new one by screwing locking screws clockwise Except for 96x0 2ml module the locking screws of other sample slot module may not fall off from module after tightening Operation of the device is prohibited if no sample slot module is assembled VI Operational Method 1 Installation 1 1 The table on which the device is placed should be even and rigid Four rubber feet of the device should fully contact table surface 1 2 Large space surrounding the device should be kept to allow for air ventilation and direct sunshine should be avoided 1 3 Power supply please properly use the voltage to meet local charge 1 4 Check whether 5A fuse tube is installed in the fuse tube box on the back of the device New fuse tube of the same specification should be installed if the old one is broken VI Standard Ex factory Configuration Standard Ex factory Configuration of the device one main unit one 48x0 5ml sample slot module one set of transparent sample support Sample slot module of other specification will only be available by separate ordering or replacement Vil 1 Precautions The table on which the device is placed should be much rigid to avoid sympathetic vibration Large space should be kept surrounding the device to allow for air ventilation and direct sunshine sh
3. ould be avoided Four feet of the device should keep stable contact with table surface Power supply please properly use the voltage to meet local charge It is strictly prohibited to wrongly use AC 380V power supply to avoid apparatus damage Please replace broken fuse tube with 5A one 4 When installing sample slot module two mating faces should be clean and locking screws should be tightened Operation of the device is prohibited if no sample slot module is assembled Transparent sample support can be placed on machine in operation As it is a design of fast movement and noise will appear when excess rotation speed is set low rotation speed is preferred when using transparent sample support 5 Check and make sure mating of the centrifugal tube in use with pipe hole of sample slot module is good if not replace it with a quality centrifugal tube meeting specification 6 Sample slot module should be placed at a dry place with good ventilation If in 10 use the pipe hole of module accidently contacts sample liquid it should be rinsed with water and dried by airing to avoid corrosion of the module Sample slot module should be cleaned and sterilized with neutral cleaner to avoid cross infection The mixing frequency of sample slot module should not be higher than allowable maximum mixing frequency In case of trace mixing high frequency is not the sole determinant of perfect mixture Operational parameters
4. ro line and earth line is prohibited to avoid injury caused by electric shock There shall be no interference from corrosive gas and electromagnetic field around the device to avoid premature failure of its protective outer layer and interference to its electrical components The device is placed levelly to ensure even loads of four rubber feet a Start Stop IV Operational instruction Display Window 99 0 is being shown in Temperature Display Window The window will display set temperature in standby mode and display actual temperature in operation with display precision of 0 1 and setting range of 1 99 2 30 is being shown in Time Display Window meaning operational time of two and a half hours Hour is shown before decimal and Minute is shown behind decimal It will constantly be on in standby mode and its decimal will keep blinking during operation Timing will start once the temperature reaches preset value Countdown is shown in Time Display Window and operation will automatically stop once time is out Key TEMP A Add set value of temperature y Drop set value of temperature TIME Add set value of time y Drop set value of time START STOP Start stop operation V Installation and replacement of sample slot module Sample slot module is assembled on temperature control module Two locking screws on the modules are used to tighten it When it is required to replace it with a samp
5. should be set in standby mode Program parameters should not be modified during operation The countdown will start once preset temperature is reached 9 Our company should be contacted for check or repair if there is any failure in control system 12
Download Pdf Manuals
Related Search