RM-770 ROBOT VACUUM CLEANER
Contents
1. Right A Holding the button down increases the angle of the turn Left gt This makes the RM 770 turn Left 10 degrees and then clean forward Holding the button down increases the angle of the turn Backward W ss This makes the RM 770 move backwards for approx 30cm needs clear slow commands The effective distance of the Remote Control is 5 7 meters Do not press more than one button on the remote control at any one time as the Robomaid Installing or Replacing Batteries for the Remote Control Please note batteries for the Remote Control are not included and need to be purchased separately It requires 2 x AAA size batteries Slide open the battery cover on the Remote Control and remove batteries if needed Insert two batteries Please ensure the batteries are in the correct direction as shown below otherwise damage may be caused If the Remote Control will not be used for a long amount of time it is best to remove the batteries How to use the Docking Station Connect the Power Adaptor to the Docking Station The display will show the time and day as being Monday 8 00 am There are 5 buttons as shown in the figure below including ON OFF Button O Full Go Button Medes Clock Button a Timer Button Adjust Button a ee Please note the buttons will only work if the Robomaid is NOT charging on the Docking Station Full Go Mode Press the Full Go2. press the Power Button for the cleaner enter Sleep Mode which will save power and all indicators will be off When the cleaner enters Sleep Mode it can not be started by pressing any button on either the cover or the remote control Press this button again to enter Standby Mode AUTO Button Press this button and the Robomaid RM 770 will work in an automatic cleaning mode until the battery power is used and then will automatically search for the Docking Station for recharging Press this button for the Robomaid RM 770 to start cleaning in the SPOT Button indicated mode and once finished will not go into Docking Mode See Page 7 Press this button for the Robomaid RM 770 to start searching for the Docking Station DOCKING Button Wall Following Button L1 Activates cleaning in the wall hugging mode and once finished will not go into Docking Mode See Page 7 UV Button Switches the UV lamp on and off Speed Adjuster V Changes between 3 different speeds of operation The default speed is the fastest Pause button Stops the Robomaid and enters Standby Mode Directional Buttons Forward Backward Left Right Press the arrow buttons to control the Robomaid RM 770 to move in the designated direction Forward A This makes the RM 770 clean forwards and it will automatically stop when it meets an obstacle This makes the RM 770 turn Right 10 degrees and then clean forward
3. button oe Ae to enable the Full Go Mode when the battery has been fully recharged cleaning will automatically begin If the timer has been set and Full Go Mode has been enabled the timer will take priority To disable Full Go Mode press the Full Go button again and make sure the Full Go icon is not showing on the bottom right of the LCD display Setting The Time Press the Clock Button to begin setting the time Press it again to switch between setting minutes hours and days The selected item will flash Press the Adjust Button to adjust minutes hours and day of the week Once desired time is reached press the Full Go button PA to save To Cancel setting the time press the ON OFF Button 1 or Timer Button N Setting The Cleaning Timer Press the Timer button O to begin setting the Cleaning Timer Press it again to switch between setting minutes hours and days The selected item will flash Press the Adjust Button to adjust minutes hours and days Setting the Cleaning Days The selected day will flash for 5 seconds then stop This indicates this day has been selected as a cleaning day Press the Adjust Button to move to the next day which will start flashing To NOT select a day press the the Adjust Button while that day is flashing and that day will be skipped and the next day will flash Once desired setting is reached press the Full Go button
4. can be switched ON or OFF however it can not be activated until the power adaptor has been disconnected During the charging process the TIME icon will show on the display and the battery level bars will flash to indicate charging See Figure 3 Upon completion of the charging the display will show 3 full red bars and the TIME icon will disappear See Figure 4 During the charging the display will show the amount of charging time where the number shown times 10 equals the actual number of charging in minutes When the Robomaid is not being used it is best to keep it in Charging Mode either on the Docking Station or connected to the Power Adaptor Please take care when plugging in Power Adaptor f AN Zy Please take care when plugging in Power Adaptor Figure 1 Figure 3 1 9 19 V FAND The Robomaid will enter Standby Mode if the power supply is cut off during the charging process and the Robomaid is switched ON A full charge takes about 3 5 hours for the first 3 times after purchasing the RM 770 please ensure it is charged for at least 12 hours each time to build battery capacity Please try to fully use the battery power before charging for the first 3 times 1 Take out the battery before disposing of the product 2 Always remember to cut off the power before removing the battery 3 Recycle or dispose of the battery properly 4 Do not throw battery into fire 5 If the batt
5. must be inserted in the cleaner first See Figure 1 Insert the pin shown in Figure 1 into the matching hole in cleaner and push it inward the other end of the brush can then be inserted into the gear end See Figure 2 Figure 1 Figure 2 How to Clean the Main Brush For a better cleaning effect you must regularly clean out the hair yarn and large debris wound on or adhered to the main brush and the dust on the suction inlet Use the cleaning brush to clean paper scraps or minute particles Wound hair yarn or similar objects should be cut by scissors or pulled out by hand while carefully rotating the main brush Both ends of the main brush be regularly cleaned as lack of maintenance may cause damage To ensure a more effective cleaning of the RM 770 please regularly remove and clean the ends of the main brush thoroughly Please clean the main brush after the first 3 times to judge how often the brush should be cleaned Any damage caused by lack of cleaning and maintenance may not be covered under warranty Storing the Robomaid RM 770 The Robomaid RM 770 should be stored in ventilated and dry places Avoid damp areas and direct sunlight Trouble shooting If you experience some issues while using your Robomaid RM 770 please use the following guide and please feel free to contact our Customer Care team The Robomaid Stops while Working Check if the selected cleaning time is over Check if there s an
6. Damage due to lack of cleaning or maintenance will not be covered under warranty Please remember to regularly clean the main brush after each use for the first three uses and ensure the brush is cleaned regularly Components RM 770 Robot Vacuum Cleaner Virtual Wall Docking Station Remote Control Power Adaptor Si NY Mopping Attachment Spare Filters 2 x Side Brushes Cleaning Brush User Manual Furniture Protection 2 x cloth and holder Adhesives Names of Parts lop View Front Bumper Infrared Receiver LED Display Control Panel Mode Button Select Button UV Button Run Pause Button Dustbin Bottom View Sensor Sensors UV Lamp Charging Contact Points 7 Front wheel Side Brush M PEPEN SS Left Right wheels Main Brush NN Auxiliary wheels Sensor Rubber Seal Power Switch Battery Cover Mopping Attachment Direct Charging Socket Names of Parts Docking Station Skidproof Floor Pads Clock Button Adjust Button Timer Button On Off Button Full Go Button Power Adaptor Socket Charging Terminals Remote Control LED Display Control Panel Indicator On Off Button Auto Button Docking Button Digital display Wall Following Button Spot Clean Button Auto Indicator Time Indicator Forward Spot Indicator UV Indicator 5 Left Right Battery Power Docking Error indicator ause Backward Indicato
7. ROBOMAID RM 770 ROBOT VACUUM CLEANER Thank you for purchasing the Robomaid RM 770 Robot Vacuum Cleaner Please read this manual carefully before using this product AN Warning No one other than official Robomaid Australia service personnel may Do not use any charger other than that enclosed with the Robomaid otherwise damage may be caused to the product and may result in fire or electric shock disassemble repair or alter this product otherwise fire electric shock or personal injury may be caused N h the Rob id with Do not bend the power cord exces OVET FOUC THe BODOM AAIEN WEL sively or place any weight on it hands or it may cause an electric shock otherwise the cable may be damaged and may cause fire or electric shock Avoid putting your clothes or any part Keep the Robomaid away from naked of your body Into the brush or wheels flame or any other heat source and of the Robomaid otherwise personal away from flammable material injury may be caused The power should be turned off when The plug of the electric wire of the transporting or storing the Robomaid for charger must be inserted tightly along time otherwise the battery may otherwise electric shock short circuit be damaged smoke or fire may be caused Remove all objects that are easily damaged before using otherwise the Robomaid may be damaged or damage the objects Always check the charger and the socket for proper connection Do n
8. code and refer to the table on the previous page The Robomaid is about 11cm high but can get stuck on furniture that has a gap of between 10 11cm If this is the case try sectioning the area off with a Virtual Wall or if possible increase the height of the furniture by 1cm If the Robomaid is getting stuck on carpet check that the mopping attachment is removed The Robomaid can get stuck on any long strands of carpet fringes of rugs cables shoelaces etc so ensure the area is tidy and free from any obstacles that it may get stuck on If there is a situation that the Robomaid gets wedged the sensors may not detect this Use a Virtual Wall to avoid these areas Docking Station display goes out The docking station display can cut out if moved frequently Reset the display by unplugging the Docking Station and leaving it offline for about 48 hours In the meantime charge the Robomaid directly with the Power Adaptor The display of the Docking Station should come back and remain fixed The Robomaid Doesn t Detect Stairs or Ledges The Robomaid will detect stairs that are 10cm or higher If the top step or ledge is rounded the Robomaid may have trouble reversing away from it Use a Virtual Wall If the floors are especially shiny the floors may reflect the sensors and the Robomaid may not detect the step Always supervise the Robomaid when using it near a stair case Never put the docking station or any object that will cause t
9. em he to save To Cancel setting the timer press the ON OFF Button or Clock Button Switching The Cleaning Timer Off Press the Timer button ra to begin setting the Cleaning Timer Press it again twice to adjust the days The selected day will flash Press the Adjust Button to clear off that day while the day is flashing Press the Adjust Button repeatedly until all the days are cleared then quickly press the Full Go button aa to save A N While programming the Timer the ON OFF Button is Cancel and the Full Go Button is Save How to Use The Virtual Wall The Virtual Wall sends a special infrared signal to prevent the Robomaid RM 770 from entering unnecessary or unwanted areas or to reduce the cleaning area am Before using the Virtual Wall install the batteries as shown in Figure 3 open the bottom cover of the Virtual Wall install 2 x D batteries After the installation close the bottom cover and tighten the screws Make sure you put the batteries in the correct way WAT Select the distance selector of the Virtual Wall according to the actual requirements Slide the switch to the top position to select the lowest level 0 4m to the middle to select the middle level 4 7m and to the bottom to select the highest level above 7m See figure 2 The lowest level uses the least amount of power WEA Press and hold the power button on the Virtual Wall and the indicator
10. ery is leaking do not touch any leakage Use a dry cloth and dispose of the battery 6 Do not impact battery or drop from a high place Removing Replacing the Battery Open the battery cover with a phillips head screwdriver and disconnect the battery as shown below When connecting a new battery ensure the red and black connectors match up otherwise damage may be caused The battery model number is YX Li 022148 Operating the Robomaid The Robomaid must be switched ON to be activated The Robomaid may be activated from Standby Mode or Charging Mode from the Docking Station There are several ways to activate the Robomaid to start cleaning Remote Control See page 8 Timer See page 9 Control Panel on the Robomaid See below Once activated the Robomaid will start cleaning int he selected cleaning mode AUTO 1 is the default mode loose cables carpet fringes that are longer than 3 4cm and other long flexible objects may get tangled in the main brush Please ensure all wires and other loose objects are removed from the Robomaid s path as If the Robomaid detects a place with a lot of dirt or debris the DIRTY icon on the display will light up and the Robomaid RM 770 will increase the cleaning intensity in that area The number of minutes the Robomaid is cleaning for will be shown during the cleaning process on the display The running time of the Robomaid will vary based on several
11. he Robomaid to reverse near the top of the stairs or near a ledge Use the Virtual Wall across the top of the stairs if needed The Dustbin won t come out The dustbin does fit tight in the cleaner to create a better seal for the vacuuming If the dustbin is difficult to open use one hand and push the top of the silver button with your thumb and at the same time use your fingers underneath the dustbin to slide it out if needed Pushing down on the front of the Robomaid while pressing the button also helps The Dustbin keeps coming out Check that the filters in the dustbin are installed correctly Check the latch on the top of the dustbin is operating correctly Virtual Wall won t switch on Ensure the batteries are installed correctly See page 10 for a diagram When switching the Virtual Wall on hold the ON OFF button down for a few seconds until the green light starts flashing Robomaid suddenly became extremely noisy URGENT The main brush must be revomed and cleaned thoroughly especially the ends of the brush to prevent damage General Hints Remember to keep the Robomaid clean and be sure to regularly clean the main brush to keep it free of excessive hair Keep the Docking Station in a clear area away from wireless devices with plenty of room on either side and in front of it to allow the Robomaid to dock correctly Be sure to charge the Robomaid for at least 12 hours for the first few times of use Be
12. hesives are very difficult to remove Standby Mode Switching the power switch to ON see the figure below switches the Robomaid ON and into Standby Mode In Standby Mode the current mode will be displayed the default is AUTO 1 If the Robomaid is left in Standby Mode for more than 3 5 minutes it will start chirping every 30 seconds until the Robomaid is activated switched OFF or recharging To turn the RM 770 off just switch the power switch to the OFF position While the RM 770 is switched OFF the remote control timer or control panel will not work Docking Mode In Docking Mode the Robomaid RM 770 will automatically begin to search for the Docking Station to recharge when the battery level is lower than 15 When the Robomaid is in Docking Mode the display will show the three red battery bars see Figure 1 and the sound of the Robomaid will be almost silent as the brushes and vacuum do not work in Docking Mode Pressing the DOCKING button on the Control Panel of the Robomaid RM 770 or on the Remote Control will manually activate the search for the Docking Station to recharge While the Robomaid RM 770 searches for the Docking Station pressing any other button on Control Panel or Remote Control will stop the RM 770 searching and enter Standby Mode The directional buttons on the Remote Control can also be used to manually assist the searching function The Robomaid will search for the Docking S
13. ot sit or stand on the Robomaid as it may cause damage of the Robomaid or cause personal injury Please use the Robomaid cautiously in the presence of children to prevent injury or harm O O Prevent the Robomaid from absorbing Never use the Robomaid in an extremely water or any other liquid otherwise small space otherwise the product the product may be damaged may be damaged Do not use the Robomaid outdoors Do not use the Robomaid for commercial otherwise the product may be cleaning otherwise it may be damaged damaged due to excessive usage Please ensure to remove any threads i cords cables fringes or long items such atits front Never place the Docking Station as shoelaces that the Robomaid may get Orany object near the top of stairs or ledges tangled with that the Robomaid will reverse away from The Robomaid does not detect a lack of Ensure the Robomaid is operating on a clea traction from its drive wheels Avoid using surface free from moisture spills moist food it in areas that result in the drive wheels or waste or any object or substance that slipping may cause marking if moved or dragged Failure to observe any of the above safety precautions will void warranty AN Do not look directly into the built in UV lamp PLEASE NOTE that although the Robomaid RM 770 Robot Vacuum Cleaner is designed for automated use and convenience it does require regular cleaning and maintenance
14. r Dirt indicator UV button AUTO VACUUM Speed Adjuster Setting Up The Docking Station Place the Docking Station on level ground with the back against a wall Make sure that there are no obstacles or uneven ground in the area within 3 meters in front of the Docking Station and 0 5m toward the left and right of it See figure 1 Ensure that Infrared Transmitter on the Docking Station is clean free from dust and uncovered otherwise the Robomaid RM 770 may not automatically recharge correctly Connect the Power Adaptor to the Power Socket of the Docking Station See figure 2 Tidy up any electric wires along the wall to avoid obstructing the operation of the Robomaid Avoid placing the docking station near year TV or other wireless based device Never place the docking station near the top of a stair case or ledge as the Robomaid RM 770 will reverse away from the docking station Please take care when plugging in Power Adaptor Figure 1 Figure 2 Furniture Protection Adhesives If the Robomaid does not detect an object in front of it it will use the bumper to recognise the object and change direction To further protect your furniture and other obstacles you can stick the furniture protection adhesives on the bumper of the Robomaid where appropriate Please ensure the adhesives do not cover the red sensor strip on the front bumper as shown to the right Please note that once stuck on the ad
15. s not work Check the battery status of the Remote Control Check the battery status of the Robomaid RM 770 Clean the infrared sensor or the beam sensor of the Remote Control with a clean and dry cloth Keep a distance of 2 3 meters between the cleaner and the Remote Control and then operate the remote directly pointing toward the cover of RM 770 Ensure you are pressing the buttons slowly and giving clear commands to the Robomaid The RM 770 Fails to Return to the Docking Station Check whether the power supply is properly connected between the adaptor and Docking Station Check the battery power if it s too low it must be charged directly with the power adaptor Try a different location of the Docking Station as the signals can have interference by wireless devices such as TV Stereo Hi Fi or PC accessories Ensure there is adequate space around and in front of the Docking Station Ensure the Docking Station is on a flat floor and not slightly raised by plush carpet The noise level is increased dramatically Clean the main brush from any obstacles and hair Clean the dustbin and the filters Check whether the brushes are excessively dirty and ensure both ends of main brush are free from hair Robomaid won t charge on the Docking Station If the Robomaid goes completely flat it will need to be charged directly with the Power Adaptor Trouble shooting cont Robomaid keeps getting stuck Check the error
16. sure to keep the area tidy from objects and obstacles that the Robomaid can get stuck on Technical Specifications Model Dimensions Weight Speed Charging Time Operation Time Noise Grade Input Rated Power Capacity of dustbin Length of Main Brush Battery Country of Origin Robomaid RM 770 Diameter 35cm Height 11cm 3 5kg 24cm Sec fastest 15 cm sec slowest speed 3 5hrs 45 60 mins vacuuming plus up to 60 mins docking 65dB 24V 1A 45W 1000CC 25cm 14 4v Lithium ion Made in China Robomaid Australia Pty Ltd PO Box 7293 Alexandria New South Wales Australia 2015 Customer Service Line free call 1800 794 191 Customer Service Email customercare robomaid com au Website www robomaid com au Due to continual product improvement in design or otherwise the product you purchase may differ slightly from the illustrations in this book ROBOMAID AUS TR Copyright 2012 Robomaid Australia Pty Ltd
17. tation and once within range of the Docking Station signal will attempt to line up and dock The Robomaid may turn away from the Docking Station and move about 2 3 meters away from the Docking Station before turning back in line and docking ta ROBOMAID Figure 1 Docking Mode If the docking is not successful and the recharging does not begin the Robomaid will reverse off the Docking Station and attempt to dock again The Robomaid can also be picked up and placed on the Docking Station physically if needed If the Robomaid cannot find the Docking Station and the battery power becomes lower than 8 of the capacity it will stop searching and stop in a clear and bright place and will chirp every 30 seconds until the battery is completely flat It will then need to be charged by plugging in the Power Adaptor directly in the Robomaid Once the Robomaid docks successfully it will go into Charging Mode AN If the Robomaid runs completely empty it may not charge from the Docking Station and must be charged by the Power Adaptor connected directly to the Robomaid Charging Mode You can directly charge the cleaner with the Power Adapter or with the Docking Station See Figure 2 To charge directly via the power adaptor connect the power adaptor to the charging socket on the RM 770 See Figure 1 When charging with the Docking Station the Robomaid must be switched ON When charging with the Power Adaptor the Robomaid
18. ter inside See figure 5 The filters can be cleaned in water and then reused after drying It s recommended to clean and replace them regularly Installation of Filters Install the 2 large filters onto the filter tray then slide it into the dustbin Install the softer filter first Figure 1 First install the filter in the filter grill Figure 5 and then insert the top end into the dustbin and then clip the lower end in place Figure 4 Figure 5 Side Brush To Install align the side brush with the 2 fasteners and press it down to clip in the side brush See Figure 2 To remove nip the two fasteners of the side brush with one hand see Figure 1 and pull the side brush upward with the other hand to take it out Figure 1 Figure 2 Cleaning Sensors The sensors should be cleaned by cotton swab or soft cloth There are wall following sensors installed in the front of bumper of the Robomaid RM 770 and ground detection sensors installed under the RM 770 see the figure below To ensure a more effective cleaning of the Robomaid RM 770 please clean the sensors regularly Main Brush How to Remove the Main Brush Hold the brush and push it to the left See Figure 1 The brush will lift out easily See Figure 2 Remove and Clean the ends of the Main Brush after each run for the first 3 times Figure 1 Figure 2 How to Install the Main Brush Hold the brush the end with the pin
19. things including flooring surface initial charging time frequency of use furniture and room layout How to use the Robomaid RM 770 Control Panel The Control Panel can be used to select the Mode or Secondary Mode of the Robomaid and activate the Robomaid The Activate button P will start the selected mode the default mode is AUTO 1 The UV button Q allows you to turn the UV lamp on or off during the cleaning The UV lamp is on by default The UV icon will light up if the UV light is on Press once to turn on and press again to turn off In standby mode with the Robomaid switched ON press the mode button Qj to select betwen AUTO SPOT and DOCKING as shown by the corresponding indicator Press the select button W to select between 1 2 and 3 secondary modes AUTO Modes 1 The Robomaid will run until the battery is fully used and then enter Docking Mode 2 The Robomaid will run for 30 minutes and then stop 3 The Robomaid will run for 15 minutes and then stop SPOT Modes 1 Robomaid RM 770 will clean in a spiral working for 1 4 minutes 2 Robomaid RM 770 will clean in a zig zag pattern working for 1 4 minutes 3 Robomaid RM 770 will follow the walls working for approx 10 minutes DOCKING This will start the Robomaid in Docking Mode See page 5 How to use the Remote Control The Power Button y When the Robomaid RM 770 is switched on
20. will start flashing If the batteries are low in power the indicator will flash faster and the batteries should be replaced a The Virtual Wall sends an infrared signal with a 15 degree range WE The Virtual Wall uses 2x D 1 5V batteries When the batteries are running low it is recommended to replace them as continued use with low power may damage the Virtual Wall AA Infrared signal emitter wall signal emitter aa Rubber pad ___ Se ean f ie 0 4m 4 7m Over 7m Figure 2 Figure 3 Indicator Installing and Replacing the Batteries You need to use a screwdriver to open the bottom cover of the Virtual Wall see Figure 3 See Figure 4 for the installation of batteries Make sure to insert the batteries in the correct way Ensure no obstacle is placed in front of the Figure 4 Virtual Wall when in use Using the Mopping Attachment When using the mopping attachment See figure 4 The Robomaid will mop the floors while vacuuming resulting in a more thorough clean The mopping cloths can be used dry or damp Attach the specially designed Robomaid mopping cloth to the mopping holder See Figure 1 Align the clips at end of the mopping holder See figure 2 to the sunken positions on the inner sides of the 2 wheels See Figure 3 and clipped them in place To stop using the mopping attachment just unclip the mopping holder It s recommended to wash and
21. wring dry the mopping cloth before using the mopping function AN Please note that mopping attachment is not designed for use on carpets or rugs The specially designed Robomaid mopping cloths are machine washable Figure 1 Attach the mopping cloth to the holder Figure 2 Figure 3 Figure 4 Removing the Dustbin Press the button on the dustbin and it will be ejected See Figure 1 The dustbin will slide out easily See Figure 2 Slide the dustbin in and push firmly to lock in place Figure 1 Figure 2 Figure 3 The dustbin does fit tight in the cleaner to create a better seal for the vacuuming If the dustbin is difficult to open use one hand and push the top of the silver button with your thumb and at the same time use your fingers underneath the dustbin to slide it out if needed Pushing down on the front of the Robomaid while pressing the button also helps How to Clean the Dustbin First open the dustproof guard and dump the dust and debris collected See Figure 1 Then clean it with cleaning brush See Figure 2 Be sure to empty the dustbin after the first use Figure 2 Figure 1 How to Replace and Clean the Filters Removal and Cleaning of Filters Hold the middle part of the filter tray located on the inside of the dustbin See figure 1 and then slide out See figure 2 The filters will easily lift out See figure 3 Unclip the rear fliter grill See figure 4 Take out the fil
22. y error information on the LED display and refer to the following table of error codes Error Code Indicated Problem Solution Left Wheel is jammed or has no traction Check the wheels for any obstacles jamming them Right Wheel is jammed or has no traction Check the wheels for any obstacles jamming them Main brush is jammed and cannot spin Clean out the main brush of any hair or obstacles Front Wheel is jammed or has no traction Clean out the front wheel of any hair or obstacles Floor Sensors not detecting Clean the floor sensors Ensure the Robomaid is not operating in direct sunlight or on black or very dark surfaces Clean the wall sensors on the bumper Ensure the Robomaid is not operating in direct sunlight This error can occur in Docking Mode if there is no clear path to the Docking Station Main Brush is not spinning any hair or obstacles Dustbin is not installed properly Internal Software Problem The Robomaid is not working as well as it did Check the battery status and ensure the Robomaid is not in Docking Mode Check whether the dustbin the filter and the inlet of suction are cleaned whether the side brush is working Check whether the cleaner is turned on Remove and Check the main brush including both ends and see if a build up of excess hair has caused damage or a malfunction N Ww Bas Wall Sensors not detecting N 1 Rokewhetsammedorhasnowcton ee The Remote Control doe
Download Pdf Manuals
Related Search