Copy of B1365T
Contents
1. Note This setting is dependent on the AGC setting e B W To keep a B W image at all times COLOR To keep a color image at all times e CDS External input signal control J EXIT MENU EXIT NO CHANGES No change e SAVE NEW AND EXIT Save change e RESTORE FACTORY SETTINGS Factory default SW REV K PREVIOUS PAGE e PREVIOUS PAGE Return page CONNECTION CAUTION Check for polarity when using a DC 12V AC 24V CAMERA SETING ANGLE r 300 0 ATTENTION 1 Do not rotate D more than 360 2 Do not twist many times unnecessarily CONTROL BOARD amp LENS ADJUSTMENT OSD controller Video Test Output Connector FUNCTIONAL OF CONTROL BOARD 1 Functional control of O S D On Screen Display 2 Functional of VIDEO OUT 2ND 1 ZOOM OCUS 2 1 Rotate Zoom lever with the supplied Allen key 2 Rotate Focus lever with the supplied Allen key DR WDR Level 20 to 20 OSD Controls Slow Shutter 2X 32X Resolution Horizontal 540 TV Lines at TDN B W 570 TV Lines Video Output VBS 1 0Vp p VBS 1 0Vp p 75 Load S N Ratio S N Ratio 48dB Humidity Less than 90 Power Power Requirement 12VDC 24VAC 12VDC 310mA 1A Heater ON 24VDC 225mA 500mA Heater ON Physical Specification Dimensions H x L 85 4 x 231 5mm Nema Type IP66 Weight 2 2 lbs Cer2. camera ID B LENS e MANUAL Use When using Manual lens e DC You can control the brightness of the screen and adjust the desired DC level from 10 to 42 C WDR EXPO EXPOSURE It has the effect of lightening or darkening the picture WDR Wide Dynamic Range You can adjust DIP switch setting D WB CONTROL e ATW Auto Tracking White Balance The camera automatically control the white balance in any environment e AWB Auto White Balance The white balance is automatically adjusted in a specific environment e MANUAL Users can adjust the colors by adding or reducing the WB level You can adjust the desired WB level from 2 500K to 9 500K E AGC e ON Activate automatic gain control feature You can adjust the desired AGC level from O to 36dB e OFF Deactivate automatic gain control feature F LOW LIGHT SLOW SHUTTER Control Image brightness by adjusting shutter speed AGC shutter speed setting Range 28 to 42 MAX FIELD Shutter open from Min x2 to Max x32 filed accumulation period e B amp W SS Black and White Slow Shutter GAIN To get brighter picture G SYNC e INTERNAL Internal synchronization e LINE LOCK Phase adjustment may be necessary in multiple camera installations to prevent picture roll when switching between cameras H RS485 e CAMERA Selectable from 1 to 255 Note Pelco D is the default DAY NIGHT e AUTO For automatic switchover from day mode to night
3. D ePIGITAL VVATCHDOG Everything s Digital 5436 W Crenshaw Street Tampa FL 33634 www digital watchdog com INSTRUCTION MANUAL B1365T About manual Before installing and using the camera please read this manual carefully Be sure to keep it handy for future reference PRECAUTIONS Do not open or modify Do not open the case except during maintenance and installation as it may be dangerous and cause damages Do not put objects inside the unit Make sure that no metal objects or flammable substances get inside the camera It could cause fire short circuits or damages E Be careful when handling the unit To prevent damage do not drop the camera or subject it to strong shock or vibration E Install away from electric or magnetic fields E Protect from humidity and dust E Protect from high temperature Be careful when installing close to the ceiling in a kitchen or boiler room as the temperature may rise to high levels E Cleaning Dirt can be removed from the case only by wiping it with a soft cloth moistened with a soft detergent solution E Mounting Surface The mounting surface material must be strong enough to support the camera WARRANTY INFORMATION Digital Watchdog referred to as the Warrantor warrants the Camera Series against defects in materials or workmanship as follows LABOR For the initial five 5 years from the date of original purchase if the camera is determined to be defectiv
4. any breach of the warranty All express and implied warranties including the warranties of merchantability and fitness for particular purpose are limited to the applicable warranty period set forth above Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above exclusions or limitations may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state If the problem is not handled to your satisfaction then write to the Address above Service calls which do not involve defective materials or workmanship as determined by the Warrantor in its sole discretion are not covered Costs of such service calls are the responsibility of the purchaser TROUBLESHOOTING Before sending the camera out for repair check the items below If the problem persists after checking these items contact your service center H if no image appears Is the coaxial cable attached securely Are the power and voltage normal Has the iris of the lens inside the camera been adjusted correctly with the level volume Is there adequate illumination H If the image is unclear Is the lens in focus Is the lens dirty Dirt of fingerprints on the lens can adversely affect the images Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid c
5. e the Warrantor will repair or replace the unit with new or refurbished product at its option at no charge PARTS In addition the Warrantor will supply replacement parts for the initial five 5 years To obtain warranty or out of warranty service please contact a Technical Support Representative at 1 866 446 3595 Monday through Friday from 9 00 AM to 5 00 PM Eastern A purchase receipt or other proof of the date of the original purchase is required before warranty service is rendered This warranty only covers failures due to defects in materials and workmanship which arise during normal use This warranty does not cover damage which occurs in shipment or failures which are caused by products not supplied by the Warrantor or failures which result from accident misuse abuse neglect mishandling misapplication alteration modification faulty installation set up adjustments improper antenna inadequate signal pickup maladjustment of consumer controls improper operation power line surge improper voltage supply lightning damage rental use of the product or service by anyone other than an authorized repair facility or damage that is attributable to acts of God LIMITS AND EXCLUSIONS There are no express warranties except as listed above The Warrantor will not be liable for incidental or consequential damages including without limitation damage to recording media resulting from the use of these products or arising out of
6. ommercially available Is the monitor adjusted correctly DIMENSION mm CoLa 85 4 OPTION CABLE LENGTH STANDARD 13 78 350 0mm WARNING TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE BNC JACK VIDEO yellow AC 24V or DC 12V Smm TWIST SOLDERING CAMERA SETTINGS R20 NT PAL E OSD MENU CONTROL CENTER KEY Used to access menu mode Also used to confirm the setting e UP DOWN KEY Used to choose the desired menu selection e LEFT RIGHT KEY Used to choose the desired menu feature adjustment E OSD MUNU ENTER EXIT A OSD MENU ENTER e Pushing Center Key for 3 seconds B OSD MENU EXIT e Press EXIT Menu from Main Menu lf Pressing Set Key for 3 seconds from Main Menu appears In this case just press Set Key C SAVE and QUIT e Left or Right Key Selecting Menu Up or Down Key Returning to Menu 1 Press the SET key to access the main setup mode 2 Select the desired feature using the UP or Down key 3 Change the status of the selected feature using the LEFT or RIGHT key E MAIN MENU A SETUP ID DISPLAY ID ON The ID name will displayed in the monitor OFF The name will not displayed in the monitor CAMERA ID You can be written to 12 characteristic ID POSITION Select on screen position of the
7. tifications CE FCC RoHS Certified Power Consumption
Download Pdf Manuals
Related Search