USB 2.0 DVI KVM Extender CE610 User Manual
Contents
1. Features Uses a single Cat Se cable to connect the local and remote units Allows access to a computer or KVM installation from a remote console Superior Video Quality up to 1920 x 1200 60 Hz at 100 m Supports HDBaseT connectivity technology Transparent USB Support supports all USB 2 0 High Speed device Extends local PC Video Keyboard Mouse to Remote side Built in 8KV 15KV ESD protection Contact voltage 8KV Air voltage 15KV ExtremeUSB supports transparent USB 2 0 signals and true plug and play no software or drivers required USB 2 0 Support connects devices such as keyboard mouse flash drive printer touch panel USB 1 1 web cameras and other USB devices which require moderate amounts of bandwidth Works with all major operating systems Windows OS X and Linux Note The CE610 supports a maximum combined USB transfer rate of 30 Mbps for attached USB devices Chapter 1 Introduction Requirements Consoles A DVI D monitor capable of the highest resolution you will be using on any computer in the installation A USB keyboard A USB mouse Computers The following equipment must be installed on each computer that is to be connected to the system A DVI D DVI I port 2 USB ports for the mouse and keyboard Microphone and speaker ports optional Cables For optimal signal integrity and to simplify the layout we strongly reco2. Monospaced A Indicates text that you should key in Indicates keys you should press For example Enter means to press the Enter key If keys need to be chorded they appear together in the same bracket with a plus sign between them Ctrl Alt Numbered lists represent procedures with sequential steps Bullet lists provide information but do not involve sequential steps Indicates selecting the option on a menu or dialog box for example that comes next For example Start gt Run means to open the Start menu and then select Run Indicates critical information Product Information For information about all ATEN products and how they can help you connect without limits visit ATEN on the Web or contact an ATEN Authorized Reseller Visit ATEN on the Web for a list of locations and telephone numbers International http www aten com North America http www aten usa com Chapter 1 Introduction Overview The CE610 USB 2 0 DVI KVM Extender is a DVI and USB Extender that supports Extreme USBO and HDBaseT technology The CE610 USB 2 0 DVI KVM Extender can extend DVI and USB 2 0 signals up to 300 ft 100 m from the source using a single Cat 5e 6 cable The CE610 is equipped with USB connectors which allow you to extend any USB device between the units The USB functionality provides not only peripheral sharing but also provides support for touch panel control and file transfer The CE610 is ideal for tr
3. Flashes green to indicate that the host is in suspend mode OFF indicates that the link is inactive Video Green Flashes to indicate normal video activity Lights steadily to indicate HDCP video activity OFF indicates that there is no video activity 13 Appendix Safety Instructions General Read all of these instructions Save them for future reference Follow all warnings and instructions marked on the device This product is for indoor use only Do not place the device on any unstable surface cart stand table etc If the device falls serious damage will result Do not use the device near water Do not place the device near or over radiators or heat registers The device cabinet is provided with slots and openings to allow for adequate ventilation To ensure reliable operation and to protect against overheating these openings must never be blocked or covered The device should never be placed on a soft surface bed sofa rug etc as this will block its ventilation openings Likewise the device should not be placed in a built in enclosure unless adequate ventilation has been provided Never spill liquid of any kind on the device Unplug the device from the wall outlet before cleaning Do not use liquid or aerosol cleaners Use a damp cloth for cleaning The device should be operated from the type of power source indicated on the marking label If you are not sure of the t
4. into a power source plug the adapter s power cable into the CE610L s Power Jack Use a DVI cable to connect the DVI D output port on the Remote Unit CE610R to your monitor Plug the cables from the remote USB devices mouse keyboard etc into their respective USB ports on the Remote Unit CE610R Plug the second power adapter supplied with this package into a power source plug the adapter s power cable into the CE610R s Power Jack CE610 User Manual Installation Diagram CE610L Rear View L Wr Cat 5e cable T A cable AM cable Local PC an a em EAN Wey ee CE610R Rear View Dee fas Chapter 3 Operation LED Display The CE610 Local and Remote Units have front panel LEDs to indicate their operating status as shown in the tables following CE610L Local Unit and CE610R Remote Unit LED Indication Power Green Lights steadily to indicate that the system is receiving power Link Green Lights steadily to indicate that the connection to the Local and Remote units is ok OFF when there is a problem with the connection USB Green Lights to indicate that the USB connection to the host com puter is working
5. or fitness for any particular purpose The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions or update For further inquiries please contact your direct vendor 19
6. After a device is inserted into the rack carefully extend the rail into a locking position and then slide the device into the rack Do not overload the AC supply branch circuit that provides power to the rack The total rack load should not exceed 80 percent of the branch circuit rating Make sure that all equipment used on the rack including power strips and other electrical connectors is properly grounded Ensure that proper airflow is provided to devices in the rack Ensure that the operating ambient temperature of the rack environment does not exceed the maximum ambient temperature specified for the equipment by the manufacturer Do not step on or stand on any device when servicing other devices in a rack 16 Appendix Technical Support International For online technical support including troubleshooting documentation and software updates http eservice aten com For telephone support Telephone Support page iv North America Email Support support aten usa com Online Technical Support Troubleshooting Documentation Software Updates http www aten usa com support Telephone Support 1 888 999 ATEN ext 4988 When you contact us please have the following information ready beforehand Product model number serial number and date of purchase Your computer configuration including operating system revision level expansion cards and software Any
7. Unit to Unit Port The Cat 5e cable that connects the Local and Remote Units plugs in here 4 DVI D In Port Connect a DVI cable from a computer to this port 5 USB Type B Input The USB cable from your computer or USB hub plugs in here 6 Power Jack The cable from the Power adapter connects here CE610 User Manual CE610R Remote Unit Front and Rear View Front View 0000 Rear View No Component Description 1 LEDs The CE610R has four LEDs to indicate operating status Power Link USB and Video 2 Firmware Upgrade Port The Firmware Upgrade Port is reserved for technical support If you would like to upgrade the unit s firmware yourself please contact your ATEN dealer 3 Unit to Unit Port The Cat 5e cable that connects the Local and Remote Units plugs in here 4 DVI D Out Port Connect a DVI monitor to this port 5 USB Type A Ports Your USB 2 0 devices plug in here 6 Power Jack The cable from the Power adapter connects here Chapter 2 Hardware Setup device is provided on page 14 Please review it before l 1 Important safety information regarding the placement of this proceeding 2 Make sure that the power to all devices connected to the installation are turned off You must unplug the power cords of any computers that have the Keyboard Power On function Rack Mounting For convenience and flexibility
8. service the device yourself Refer all servicing to qualified service personnel If the following conditions occur unplug the device from the wall outlet and bring it to qualified service personnel for repair The power cord or plug has become damaged or frayed Liquid has been spilled into the device The device has been exposed to rain or water The device has been dropped or the cabinet has been damaged The device exhibits a distinct change in performance indicating a need for service The device does not operate normally when the operating instructions are followed Only adjust those controls that are covered in the operating instructions Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair 15 CE610 User Manual Mounting Before working on the rack make sure that the stabilizers are secured to the rack extended to the floor and that the full weight of the rack rests on the floor Install front and side stabilizers on a single rack or front stabilizers for joined multiple racks before working on the rack Always load the rack from the bottom up and load the heaviest item in the rack first Make sure that the rack is level and stable before extending a device from the rack Use caution when pressing the device rail release latches and sliding a device into or out of a rack the slide rails can pinch your fingers
9. the CE610 can be mounted on system racks To rack mount a unit do the following 1 Using the screws provided in the Mounting Kit screw the mounting bracket into the top or bottom of the unit as show in the diagram below Phillips hex head 3x6 CE610 User Manual 2 Screw the bracket into any convenient location on the rack MED ATAR MD ATA MT TUT 0 TUT 0 O 0 TUT O OO O OO MT E a IDO Note These screws are not provided We recommend that you use M5 x 12 Phillips Type I cross recessed type screws Chapter 2 Hardware Setup Installation Grounding To prevent damage to your installation it is important that all devices are properly grounded 1 Use a grounding wire to ground both units by connecting one end of the wire to the grounding terminal and the other end of the wire to a suitable grounded object IPN 2 Make sure that the computer that the Local Unit connects to and the monitor that the Remote Unit connects to are properly grounded 15 lam S Cat ae te l up to m e N ol em a e S Pa CE610 User Manual 3 For increased grounding protection use STP shielded twisted pair cable to connect the Local and Remote Units There are two methods that ca
10. twisted pair STP cables must be used with the unit to ensure compliance with FCC amp CE standards KCC Statement A ASS AR 7171 EFE y 90171713 BES A AAAS 7 SA HA ES ARSE 0 3279347 0 74 99 Il ALB SHE AS EH 03 suc RoHS This product is RoHS compliant Ze CE610 User Manual SJ T 11364 2006 The following contains information that relates to China ABSEWRRTK SHER TT Ate SRE zusam eaat e Oo O O O maal Oo o O O O O RR ASA SORERZACM AY ROA AE EAST 11363 20064 EHR SE RZ Fo O ATFERANHERK RASA EMIR E DATA O R YRAMAPHS BMY SIT 11363 20060 R EEK x RIMAS EUR EVA RR ARA HSJ T 11363 2006 HR BER CE610 User Manual User Information Online Registration Be sure to register your product at our online support center International http eservice aten com Telephone Support For telephone support call this number International 886 2 8692 6959 China 86 10 5255 0110 Japan 81 3 5615 5811 Korea 82 2 467 6789 North America 1 888 999 ATEN ext 4988 United Kingdom 44 8 4481 58923 User Notice All information documentation and specifications contained in this manual are subject to change without prior notification by the manufacturer The manufacturer makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties as to me
11. ATEN USB 2 0 DVI KVM Extender CE610 User Manual www aten com CE610 User Manual EMC Information FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense The device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment CE Warning This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Suggestion Shielded
12. Mounting iii renta dor an 7 Installation 42 4 4 ee er ar 9 GTO ivi or are re c 9 Setting UP evo a ae eee a See 11 Installation Diagram 2222er een eee 12 Chapter 3 Operation LED Display 2 22 442 a a A RR RG 13 CE610L Local Unit and CE610R Remote Unit 13 Appendix Safety Instructions ic ea 14 Generale 2 fetes Ot Lit ne cod e Lana Ledo e a e tas dd edo 14 Mounting ena iio a ep bee po 16 Technical Support seese neose na cee ee pede ek oe ale nn 17 International 2 24 ee eed hea 17 North America e pene ee deed 17 vi CE610 User Manual Specifications Limited Warranty vii CE610 User Manual About this Manual This User Manual is provided to help you get the most from your system It covers all aspects of installation configuration and operation An overview of the information found in the manual is provided below Chapter 1 Introduction introduces you to the CE610 system Its purpose features and benefits are presented and its front and back panel components are described Chapter 2 Hardware Setup describes the steps that are necessary to quickly and safely set up your installation Chapter 3 Operation explains the fundamental concepts involved in operating the CE610 An Appendix provides specifications and other technical information regarding the CE610 viii CE610 User Manual Conventions This manual uses the following conventions
13. ansportation centers medical facilities and shopping malls industrial kiosks and for syncing files and folders between portable and desktop computers The CE610 allows access to a computer system from a remote console USB keyboard monitor and mouse Because it allows access to a computer system from a remote console the CE610 is perfect for use in any type of installation where you need to place the console where it is conveniently accessible but you want the system equipment to reside in a safe location away from the dust and dirt of the factory floor or the harsh environmental influence of a construction site for example This allows users to deploy system equipment over large distances The CE610 is useful for control and security purposes where you can have the system unit in a secure area at the same time that you put the console in the most convenient location for user access This is ideal for managing highly confidential data systems The CE610 improves on previous designs by 1 using inexpensive Cat 5e cable instead of bulkier more expensive standard DVI cables for a much neater more convenient more reliable data transfer connection and 2 featuring a custom ASIC to ensure the utmost in reliability and compatibility Setup is as easy as can be simply connect the computer system box run the Cat 5e cable up to 100 meters to the Remote Unit and plug the remote console into the Remote Unit CE610 User Manual
14. error messages displayed at the time the error occurred The sequence of operations that led up to the error Any other information you feel may be of help 17 CE610 User Manual Specifications Function CE610L CE610R Connectors DVI In 1 x DVI D Female N A White DVI Out N A 1 x DVI D Female White USB 1x USB Type B Female 3 x USB Type A Female White White Power 1x DC Jack F W Upgrade 1 x Mini USB Unit to Unit 1 x RJ 45 Female Black LEDs Power 1 Green 1 Green Link 1 Green 1 Green USB 1 Green 1 Green Video 1 Green 1 Green USB Transfer Rate USB 2 0 Up to 30 Mbps Video 1920 x 1200 60Hz 100 m Power Consumpti Environment ion DC 5V 15 W DC 5V 15W Operating Temp 0 50 C Storage Temp 20 60 C Humidity 0 80 RH Non condensing Physical Housing Metal Properties Weight 605 g 615g Dimensions L x W x H 18 20 x 11 79 x 2 28 cm Appendix Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT DISK OR ITS DOCUMENTATION The direct vendor makes no warranty or representation expressed implied or statutory with respect to the contents or use of this documentation and especially disclaims its quality performance merchantability
15. mmend that you use the high quality custom DVI Cable that is provided with this package Cat 5e cable is required to connect the Local and Remote CE610 Units Cable of a lower standard will result in degrading of the video signal We strongly recommend using Cat 5e cables For better quality over longer distances we suggest using 2L 2801 350 MHz Low Skew Cable Maximum Cable Distances Connection Distance Computer to Local Unit CE610L 1 8 m Local Unit CE610L 100 m to Remote Unit CE610R Remote Unit CE610R to monitor 5m CE610 User Manual Operating Systems Supported operating systems are shown in the table below OS Version Windows 2000 and higher Linux RedHat 9 0 and higher SuSE 10 11 1 and higher Debian 3 1 4 0 Ubuntu 7 04 7 10 UNIX FreeBSD 5 5 6 1 6 2 Novell Netware 6 0 and higher Mac OS 10 1 and higher Note The CE610 does not support OS that do not support USB Chapter 1 Introduction Components CE610L Local Unit Front and Rear View Front View q 0000 Ea ei L 1 Rear View No Component Description 1 LEDs The CE610L has four LEDs to indicate operating status Power Link USB and Video 2 Firmware Upgrade The Firmware Upgrade Port is reserved for technical Port support If you would like to upgrade the unit s firmware yourself please contact your ATEN dealer 3
16. n be used a In addition to the eight paired wires STP cable also contains a grounding wire Solder this wire to the RJ 45 connector as shown in the diagram below 7 b The second method is to use the STP cable shielding for grounding In this case make sure that the shielding makes tight contact with the top inside of the RJ 45 connector as shown in the diagram below In either case make sure that the sides of the RJ 45 connector make tight contact with the grounding contacts on the sides of the RJ 45 socket as shown in the diagram below Pa Chapter 2 Hardware Setup Setting Up Setting up the CE610 DVI KVM Extender system is simply a matter of plugging in the cables Make sure that all the equipment to be connected are powered off Refer to the installation diagram on the following page and do the following 1 Connect the USB cable supplied with the package to the USB Type B port on the Local Unit CE610L Plug the other end of the cable into a USB Type A port on the local computer Connect the DVI D cable supplied with the package to the DVI D input port located on the Local Unit CE610L Plug the other end of the cable into the DVI port on the local computer Plug either end of the Cat 5e cable into the CE610 s Unit to Unit R J45 port Plug the other end of the Cat 5e cable into the Unit to Unit RJ 45 port of the Remote Unit CE610R Plug one of the power adapters supplied with this package
17. rchantability or fitness for any particular purpose Any of the manufacturer s software described in this manual is sold or licensed as is Should the programs prove defective following their purchase the buyer and not the manufacturer its distributor or its dealer assumes the entire cost of all necessary servicing repair and any incidental or consequential damages resulting from any defect in the software The manufacturer of this system is not responsible for any radio and or TV interference caused by unauthorized modifications to this device It is the responsibility of the user to correct such interference The manufacturer is not responsible for any damage incurred in the operation of this system if the correct operational voltage setting was not selected prior to operation PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE USE CE610 User Manual Package Contents The CE610 package consists of CE610L USB 2 0 DVI KVM Extender Local Unit CE610R USB 2 0 DVI KVM Extender Remote Unit Custom DVI 1 8 m Cable 1 8 m USB Cable Power Adapters Mounting Kit m m NO re m m User Instructions Check to make sure that all the components are present and that nothing got damaged in shipping If you encounter a problem contact your dealer Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the unit and or any of the devices connected
18. to it Features may have been added to the CE610 since this manual was published Please visit our website to download the most up to date version of the manual Copyright 2015 ATEN International Co Ltd Manual Date 2015 11 02 ATEN and the ATEN logo are registered trademarks of ATEN International Co Ltd All rights reserved All other brand names and trademarks are the registered property of their respective owners CE610 User Manual Contents EMG Information comica a aa a ii ROHS i244 dan en els Shia ted aes ii SULT 11304 2000 ex Gnade iii User Information 0 0000 eee iv Online Registration 0 0c eect teas iv Telephone Support 0 0 0 cece tees iv USeriNOUCG ae picid ia ee hoards iv Package Contents 2 cece nennen een nenn v About this Manual o A tos vii CONVENtIONS oa a o o ar en dete gen dirt viii Product Information ooooccococco eee viii Chapter 1 Introduction OVERVIEW Ae Li it Loe SiS dea E AO 1 Feature Sise Jenna as da e aa nba 2 Requirements 0 ii re Rene aer ls 3 Consoles eye Actes to do e na bo e ES rs ele e 3 Computers ie ed a Bh oad age edna ee genes dd me Ber 3 Cables nn e He eee eg we SEs 3 Op tating Systems 4 i iene 20 Seas Se See ren 4 Components iia cae ets ee ee eee Ba 5 CE610L Local Unit Front and Rear View 05 5 CE610R Remote Unit Front and Rear View 6 Chapter 2 Hardware Setup Rack
19. ype of power available consult your dealer or local power company The device is designed for IT power distribution systems with 230V phase to phase voltage To prevent damage to your installation it is important that all devices are properly grounded The device is equipped with a 3 wire grounding type plug This is a safety feature If you are unable to insert the plug into the outlet contact your electrician to replace your obsolete outlet Do not attempt to defeat the purpose of the grounding type plug Always follow your local national wiring codes Do not allow anything to rest on the power cord or cables Route the power cord and cables so that they cannot be stepped on or tripped over Appendix If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the extension cord ampere rating Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes To help protect your system from sudden transient increases and decreases in electrical power use a surge suppressor line conditioner or un interruptible power supply UPS Position system cables and power cables carefully Be sure that nothing rests on any cables Never push objects of any kind into or through cabinet slots They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock Do not attempt to
Download Pdf Manuals
Related Search