00020310 / Easytip S2 Universal Remote Control
Contents
1. 8 Point the remote control towards your TV and press the key If your TV does not respond by going into Stand By mode then repeat steps 3 to 8 and enter the next code in the list 9 If your TV goes into Stand By mode when the key pressed then your remote control has found a compatible code Next test all of the other function buttons If certain functions are not working correctly then restart the process moving onto the next code number as this may well improve the situation 10 If the codes in the list fail to operate your TV then next move onto the automatic code scan function see below Easy programming for the control of your VIDEO RECORDER To programme the remote control to operate your VIDEO RECORDER proceed as described above for the television set Complete steps 1 to 10 using the key on your remote control Please ensure that you refer to the codes listed under the VIDEO RECORDER section and not the TV section Easy programming for the control of your SATELLITE RECEIVER To programme the remote control to operate your SATELLITE RECEIVER or CABLE BOX proceed as described for the television set Complete steps 1 to 10 using the key on your remote control Please ensure that you refer to the codes listed under the SATELLITE section and not the TV section Easy programming for the control of your DVD PLAYER To programme the remote control to operate your DVD PLAYER proceed as described for the television set Comple2. USER MAN UNIVERSAL REMOTE CONTROL Thank you for purchasing this universal remote control Before using the remote you will need to insert 2 type AAA batteries not included in the battery compartment ensuring that you follow the polarity shown on the inside You can now use your remote control to operate up to 9 different devices depending on the model including a TV video recorder DVD player satellite or cable receiver CD player tuner radio tape recorder and amplifier If your remote control is equipped with an AUX key not standard on all models then you can also use it to control a second TV set video recorded satellite receiver and or cable box CD player tuner tape recorder or amplifier Aged programming for the control of your TV SET Insert 2 new 1 5V alkaline batteries of type AAA LRO3 Observe battery polarity as indicated in the battery compartment 2 Switch on your TV SET 3 In the enclosed code list find your TV brand or manufacturer e g Sony 4 Beside the manufacturer s name you will find one or more 3 digit codes These codes must be entered into the remote to enable it to work with your particular TV set 5 Press the key on the remote control for approximately 4 seconds until the LED flashes twice 6 After seeing the 2 flashes and within 5 seconds enter the 3 digit numerical code from the list 7 After entering the code the LED will flash twice indicating that the code has been accepted
3. has been accepted Special functions of your remote control Brightness Colour Contrast etc Adjusting brightness colour contrast bass tremble balance at your TV set using the universal remote control 1 Ensure that your remote control is set to TV press GD key 2 Press the GilD key 3 Within 5 seconds press for brightness for colour for contrast for tremble for bass for balance 4 To adjust the settings use the and keys 5 After 5 seconds your remote control returns to standard mode for the selection of channels OK key e At TV level The basic settings of your TV SET are activated e At TV level menu Confirmation key for settings e At VCR level Record button press key twice e At SAT level Confirmation key for settings e At DVD level Confirmation key for settings e At TAPE level Record button press key twice Please write down the 3 digit codes of your devices for future reference Depending on the remote control model you might have to reprogram me the universal control device after a battery change
4. ail to work properly then it s possible the remote has found a partially compatible code In such cases you will need to restart the automatic scanning process steps B to F until a better code is found Please note that once the automatic process is restarted the remote continues from the last stored code and not at the beginning of code database e To complete a code scan for the VCR DVD CD or TAPE follow the procedure above but use the key and not the key e To complete a code scan for the TUNER follow the procedure above but use the key R MANUAL Code scan for VCR SAT DVD CD TAPE TUNER and AMP To complete a code scan for VCR SAT DVD CD TAPE TUNER or AMP proceed as described for a TV code scan Complete above steps A to G using keys D or M or Gif and GD and Gir GHD and GR or Gil and Gil respectively At step E for SAT and AMP press the key for VCR DVD CD and TAPE press the key and for TUNER press key Finding out what code number you are using If you have programmed your remote control by means of the automatic code scan or if you have forgoten the code you have stored then the following procedure will replay the codes being used A Press the key of your remote control for approx 4 seconds until the LED flashes twice B Enter code using the numerical keys The LED flashes twice C Press key and count the number of LED flashes This number corres
5. ponds to the first digit of the code D Press key and count the number of LED flashes This number corresponds to the second digit of the code if the digit is 0 the LED does not flash E Press key and count the number of LED flashes This number corresponds to the third digit of the code if the digit is 0 the LED does not flash F Steps C D and E can be repeated as often as necessary To read the currently used code for the control of a VCR SAT DVD AUX CD TAPE TUNER or AMP device proceed as described above for your TV SET Complete steps A to F pressing the G gt GD GD GD GD Gi or GD key respectively Write down the code number as indicated by the LED Programming for AUX devices If the remote you have purchased has a separate AUX key then this can be used to operate a second TV set video recorder satellite receiver cable box CD player tape recorder tuner or amplifier To program your remote control for a second device proceed as follows 1 Press the key of your remote control until the LED flashes twice 2 Press G key for a second TV set key for a second video recorder GD key for a second satellite receiver or cable box keys Gif and for a second CD player keys and Gif for a second tape recorder keys Gil and Gi for a second tuner keys Gil and Gi for a second amplifier 3 On the numerical keypad enter a 3 digit code from the enclosed list 4 The LED flashes twice indicating that the code
6. scan If programming using the codes in the enclosed list failed to work then you must next try the automatic code scan A Ensure that the remote control is equipped with 2 new batteries see step one of easy programming procedure B Switch on your TV SET When using the automatic scan function for the VCR DVD CD or TAPE switch on your device insert a video tape DVD CD or tape cassette and put the unit into Play mode i e the VCR tape etc is running C Press the Gp key of your remote control for approx 4 seconds until the LED flashes twice D After seeing the 2 flashes and within 5 seconds enter the code After entering the code the LED will flash twice indicating that the code has been accepted E Press and hold the key until your TV switches off Please note that this process might take up to 15 minutes During the automatic scanning you can remove your finger or change hands provided it is replaced within 8 seconds If left off of the key for more than 8 seconds then the remote will revert back to its normal mode If your TV switches into Stand By mode during the automatic process then immediately remove your finger from the key and then press and release the GD key until the LED flashes twice this will then store the code that the remote has found F In some cases during the automatic scanning search the remote control might find several codes that appear to operate your TV etc however if some of the buttons f
7. te steps 1 to 10 using the key on your remote control Please ensure that you refer to the codes listed under the DVD section and not the TV section Easy programming for the control of your CD PLAYER To programme the remote control to operate your CD PLAYER proceed as described for the television set Complete steps 1 to 10 except you must first press and release the Gif key followed by holding down the key Please ensure that you refer to the codes listed under the CD section and not the TV section Easy programming for the control of your TUNER RADIO To programme the remote control to operate your TUNER proceed as described for the CD PLAYER but using the Gi key instead of the CD key Please ensure that you refer to the codes listed under the TUNER section and not the CD PLAYER section R MANU Easy programming for the control of your TAPE RECORDER TAPE DECK To programme the remote control to operate your TAPE RECORDER proceed as described for the CD PLAYER but using the key instead of the CD key Please ensure that you refer to the codes listed under the TAPE section and not the CD PLAYER section Easy programming for the control of your AMPLIFIER To programme the remote control to operate your AMPLIFIER proceed as described for the CD PLAYER Complete steps 1 to 10 using the Gi key on your remote control Please ensure that you refer to the codes listed under the AMPLIFIER section and not CD PLAYER section Code
Download Pdf Manuals
Related Search