User`s Manual
Contents
1. oco LED Definition Power Geen Lights to indicate that the HPOE 460 has power PoE Ready Grech Lights to indicate the port is In Use providing 52V DC in line power 2 Hardware Installation This product provides three different running speeds 10Mbps 100Mbps and 1000Mbps in the same device and automatically distinguishes the speed of incoming connection This section describes the hardware features of HPOE 460 Before connecting any network device to the HPOE 460 read this chapter carefully 2 1 Before Installation Before your installation it is recommended to check your network environment If there has any IEEE 802 3af 802 3at device which needs power on the HPOE 460 provides you a way to supply power for this Ethernet device conveniently and easily The HPOE 460 equips with an AC DC adapter with DC 52V input and injects this DC power into the pin of the twisted pair cable pair 4 5 and pair 7 8 If there is very difficult to find a power socket for AC DC Adapter of your Non IEEE 802 3af 802 3at networked device the HPOE 460 and POE 162S IPOE 162S can provide you a way to supply DC power for this Ethernet device conveniently and easily The 10Mbps or 100Mbps and 1000Mbps speed duplex mode from Data port of HPOE 460 depends on which Ethernet device attached s0 2 2 HPOE 460 and POE 162S the IEEE 802 3at Injector Splitter and Equipment Installation For the places hard to find2. the power inlet the HPOE 460 and IEEE 802 3at High Power over Ethernet Splitter POE 162S IPOE 162S provides the easiest way to power your Ethernet devices such as IP Camera on the ceiling and the Wireless Access Point installed on the top of the building With 4 10 100 1000Base T Gigabit Ethernet ports the HPOE 460 supports full 52V DC power for any remote IEEE 802 3af 802 3at powered device PD To control the power system of your networking devices the HPOE 460 can directly co work with PoE IP phone to build VoIP telephony network in the office Furthermore the HPOE 460 can be directly connected to any third party IEEE 802 3af 802 3at compliant devices installed 100 meters away 802 3at PoE 802 3af PoE PTZ Speed Dome IP Camera IP Camera 802 3at PoE Splitter 802 3at PoE Splitter Non PoE Device i 1000Base T UTP with PoE 1000Base T UTP i _ _ Power Line DC i Power Line Figure 2 1 HPOE 460 Application Topology 1 According to IEEE 802 3af and IEEE 802 3at standard the HPOE 460 will not inject power to the cable if not connect to IEEE 802 3af and IEEE 802 3at standard devices Due to the capability of IEEE 802 3af and IEEE 802 3at standard the HPOE 460 can directly connect with any IEEE 802 3af or IEEE 802 3at standard compliant end nodes 3 Troubleshooting This chapter contains information to help you solve issue If the High Power over Ethernet Injec
3. 1 Introduction 1 3 Features 8 Port RJ 45 1 1 Checklist m 4 Port 10 100 1000Mbps Data input Thank you for purchasing our HPOE 460 4 Port Gigabit m 4 Port 10 100 1000Mbps Data Power output IEEE 802 3at High Power over Ethernet Injector Hub the High Power over Ethernet Injector Hub package shall Mid Span PSE Power over Ethernet Check the contents of your package for following parts Up to 4 IEEE 802 3at 802 3af devices powered e High Power over Ethernet Injector Hub x 1 DC 52V power over RJ 45 Ethernet cable to devices with Ethernet port User s Manual x 1 PoE power up to 30 8 Watts 802 3at PoE 15 4 Power Adapter x 1 Watts 802 3af PoE for each PoE ports Power Cord x 1 Remote power feeding up to 100m If any of these pieces are missing or damaged please Full power support for per PoE port contact your dealer immediately if possible retain the carton including the original packing material and use Automatically detect powered device PD them against to repack the product in case there is a Circuit protection prevents power interference need to return it to us for repair between ports 1 2 About the Power over Ethernet Injector Hardware Hub m Desktop palm size wall mountable The PLANET HPOE 460 is the next generation 4 Port LED indicator power input indication Gigabit IEEE 802 3at High Power PoE injector Hub features both IEEE 802 3af and High Power IEEE m FCC Part 15 Class B CE 802 3at P
4. Ethernet Enhancement oe 1 4 Specification Product HPOE 460 Hardware Data Input Ports 4 x RJ 45 Interface Data Power Output Ports ae Data Rate 10 100 1000Mbps System Power x 1 Green LED Per PoE Port PoE ready in use x 4 Green 10Base T 2 Pair UTP Cat 5 up to 100m 328ft 100Base TX 2 Pair UTP Cat 5 up to 100m 328ft Neto cele 1000Base T 4 Pair UTP Cat 5e 6 up to 100m 328ft EIA TIA 568 100 ohm STP 100m 328ft IEEE 802 3af Per Port DC 52V 15 4 Watts PoE Power Output IEEE 802 3at Per Port DC 52V 30 8 Watts Power Pin Assignment 4 5 7 8 PoE Power Budget 120 Watts Number of 802 3af PD Class 0 1 2 3 can be powered Number of 802 3at PD Class 4 1 2 3 can be powered Number of 802 3at PD Class 4 0 4 can be powered Standards Conformance IEEE 802 3 10Base T Ethernet IEEE 802 3u 100Base TX Fast Ethernet IEEE 802 3ab 1000Base T Gigabit Ethernet IEEE 802 3af Power over Ethernet IEEE 802 3at Power over Ethernet Enhancement Regulation Compliance Environment Operating Temperature Storage Temperature Humidity Standards Compliance 1 5 Product Outlook T PU UMd 8 VIVA 52V 56VDC 00000000 ACAUTION ooo0oo0oo0o0o0o0 Remove DATA amp PWR O O O O O O O O
5. nnector There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable connection RJ 45 Pin Assignments 1000Mbps 1000Base T Oo 2 BIDA BDB O 3 BIDB BEDAH O 4 O BIDO BEDD OX Implicit implementation of the crossover function within a twisted pair cable or at a wiring panel while not expressly forbidden is beyond the scope of this standard Please make sure your connected cables are with 10 100Mbps 10 100Base TX same pin assignment and color as above picture before RJ 45 Connector pin assignment deploying the cables into your network COT MDI MDI X Media MDI X Media Dependant Dependant Interface Interface Cross Tx transmit Rx receive Tx transmit Rx receive Tx transmit White Orange Orange White Green Blue White Blue Green White Brown Brown White Orange Orange White Green Blue White Blue Green White Brown Brown ANOaABRWND ANOaARWBDNDY White Orange Orange White Green Blue White Blue Green White Brown Brown White Green Green White Orange Blue White Blue Orange White Brown Brown OAONOaRWN ANOaARWBDN Figure A 1 Straight Through and Crossover Cable Energy Saving Note of the Device This power required device does not support Standby mode operation For energ
6. ower over Ethernet PoE that combines up m 100 240V AC 50 60Hz 2A universal power supply to 30 Watts power output and data per port over one adapter with DC 52V 2 31A power output CAT 5E 6 Ethernet cable It is designed specifically to satisfy the growing demand of higher power consuming m Plug amp play network PD powered devices such as PTZ Pan Tilt amp Standard Compliance Zoom Speed Dome network cameras multi channel 802 11a b g n wireless LAN access points and other m IEEE 802 3 10Base T network devices by providing double amount of PoE E IEEE 802 3u 100Base TX power than conventional 802 3af PoE PSE m IEEE 802 3ab 1000Base T The HPOE 460 is installed between a regular Ethernet Switch and the powered devices it injects power to the m IEEE 802 3af Power over Ethernet PDs without affecting data transmission performance It offers a cost effective and quick solution to upgrade network system to IEEE 802 3af IEEE 802 3at Power over Ethernet system without replacing the existing Ethernet Switch There are 8 RJ 45 STP ports on the front panel of the HPOE 460 half of the ports on right panel function as Data input and the other half on left panel function as PoE Data and Power output The 4 PoE Data and Power output ports are also the power injectors that transmit DC voltage to the CAT 5 5e 6 cable and transfer data and power simultaneously between the Injectors and Splitters E IEEE 802 3at Power over
7. tor Hub is not functioning properly make sure the High Power over Ethernet Injector Hub was set up according to instructions in this manual How to let my Non IEEE 802 3af 802 3at network devices work with HPOE 460 Solution You can use PLANET Power over Ethernet Splitter such as PLANET POE 162S IPOE 162S to work as a power transformer between HPOE 460 and Non IEEE 802 3af 802 3at devices The POE 162S and IPOE 162S provide 12V DC and 24V DC voltage output through DIP switch The HPOE 460 PoE LED is not light Solution Check the cable connection between HPOE 460 and IEEE 802 3af 802 3at devices Why can not power my PoE device on when connect with HPOE 460 Solution 1 Please check the cable type of the connection from HPOE 460 to the other end The cable should be an 8 wire UTP Category 5 5e 6 EIA568 cable within 100 meters A cable with only 4 wire short loop or over 100 meters all will affect the power supply Please check and assure the device that fully complied with IEEE 802 3af and IEEE 802 3at standard PLANET Networking amp Communication 802 3at High Power over Ethernet Injector Hub HPOE 460 Full Power Provision Without Area Restrictions www planet com tw User s Manual a02 3at Plug amp Play Metal Shape Er 4 PLANET Technology Corp Ge w J PLANET 2350 AF0320 001 C aed rs te Appendix A Networking Connection The standard RJ 45 receptacle co
8. y saving please remove the power cable to disconnect the device from the power circuit Without removing power cable the device wills still consuming power from the power source In the view of Saving the Energy and reduce the unnecessary power consuming it is strongly suggested to remove the power connection for the device if this device is not intended to be active IEEE 802 3af 802 3at DC 48V 52V 6 Rx receive __Tx transmit IEEE 802 3af 802 3at DC OV 14
Download Pdf Manuals
Related Search