- Wiedamark
Contents
1. Foldable LED Display Specification CE FE RoHS iw Module size W 425mm W 320mm W width H height H 1700mm H 1280mm oe safety certificate CE FCC ROHS 01 Dimensions C FC RoHS All dimensions are in millimeters lt 320 4 y 1280 1680 Yo Figure 1 Information subject to change without notice Manufacturer disclaims liability for any injury damage direct or indirect loss consequential or economic loss or any other loss occasioned by the use of inability to use or reliance on the information contained in this manual 02 Safety Information CE FE RoHS Warnings Read the safety precautions in this section before installing powering operating and servicing this product The following symbols are used to identify important safety information on the product AAAAAA WARNING WARNING WARNING WARNING WARNING WARNING Safety hazard Refer to Hazardous Hotsurface Do Fire hazard Emission Risk of severe manual before voltage Risk of not touch hazardous to injury or death installing lethal or severe eyesight powering or electric shock servicing This product is for professional use only It is not for household use This product presents risks of severe injury or death due to fire hazards electric shock and falls Read this manual before installing powering or servicing this product follow the safety precautions listed below a2. Panels Hooks 32pcs Header hook plate 8pcs M8 30 Black dyeing bolt 8 pcs M8 Black nut 8 pcs 8 spring washers 8 pcs 4 flat washers 8pcs 10 DC power cable 4 pcs 11 Ethernet cable 10m 1PC according to the specific order 12 User manual and software install manual 13 1 5m Power cable to cascade with two power Power system in series 05 OO Y 0 01 Y Mi Using for the first time 1 Carefully review Safety Information on page 2 2 Check that the local AC power voltage is within the ranges of use 90 260V 50 60Hz 3 Check the rated current of the power outlet and the power is in line with the use of the product range M Folding Instructions One of features of Rubik LED Display panel is can be folded into a cuboid by the size of 330cm x 160cm x170cm Warnings Please fold the led panel according to the following image any damage shall be borne by the customer himself Manufacturer will not bear any loss Warning Don t fold the two LED display surface at the same angle you must fix one module first then turn round the other one X Two Folding Ways LED Display Surface Outward and LED Display Surface Inward As pictured above we recommend the display surface inward to protect the LED display wr A LED Display Surface Outward LED Display Surface Inward Folded Physical Installation CE FE RoHS WARNING The Safety and suitability of lifting equipment installation loc
3. a oe zr 0 _ gt CO a M Software Installation Please install according to software user manual 13 Troubleshooting CE FE RoHS Problem Probable cause s No power to panel Check power and connections Disconnect panel from power Panel is completely dead PUSE DIO Contact Professional for service Defective PSU power supply unit Contact manufacturer for service Incorrect panel settings on data Check settings display addresses processor System Controller panel Device Properties etc Inspect connections and cables One or more panels displays Fault on Data Processor link Correct poor connections Repair video incorrectly or does not or replace damaged cables Arpa Vigen aten Baralda aciwa Have faulty panel serviced by Manufacturer Replace with a device known to be operating correctly Have faulty device tested and serviced Other device e g Ethernet switch Check settings PAL SECAM NTSC selection overall panel intensity setting etc i Unusable video signal or i All panels and or monitor defective video source Check video source screen display video incorrectly naped connectons and cables t displ i t all A E LE Fault on Data Processor link Correct poor connections Repair or replace damaged cables Device on Data Processor Have faulty panel or device tested link defective and serviced by Manufacturer Ensure free ai
4. a Processor must install on the second single module from the top of each two panels See Figure 6 there must be a one to one correspondence between A B C D on screen and A1 B1 C1 D1 on Data Processor Each socket must joint into points correspond Note the slot on Data Processor must be inserted into the hinge on the screen body If it is not inserted the data processor will not be fixed on the screen It is not allowed One data processor can control 4 pcs modules on horizontal didn t include the vertical direction 09 Electrical Part CE FE RoHS System Layout Laptop VGA Input Video processor HD DVD YPbPr amp DVD Y C Input Camera CVBS Input PC DVI Input Cat5 LAN cable Cat5 LAN cable To next Dota processor A Signal Cable Signal Cable Signal Cable Signal Cable Power Cable Dota proces N 20 EH MAX 3840mm MAX 256128099 Figure 7 Rubik LED Display electrical connection is connector interconnection 10 M Panel Interconnection Panels are integral and engage automatically when panels are installed in columns Signal Cable Connection see figure 8 A input connector to D output connector cable tail with 14P cable Power Cable Connection see figure 8 B input connector to C output connector cable tail with 4P cable Notes Use corresponding connector correctly if the connectors can not be interconnected ple
5. ase changes another one Don t power high voltage the connectors work in low voltage Figure 8 M Panel and Data Processor Connection Interconnect the top of Data Processor power connectors with the Panel power connectors Interconnect the top of Data Processor signal cable connectors with the Panel signal connectors See Figure 586 Note Data Processor power output and signal output has four groups 1 2 3 4 each group must be interconnected with the corresponding group 1 2 3 4 on the single panel No need to connect Data Processor power output and signal output just need to connect group 1 group 2 or group 3 11 E Data Processor Video Processor and Power System Connection Data Processor connects with video processor with Cat 5 LAN cable Two Cat 5 LAN cables on the Data Processor signal input and signal output Input Cat 5 cable connects with video processor LAN cable Output Cat 5 cable connects with the next Data Processor signal output cable and so on The Data Processor power input cable connects with the Power Systems by one DC output power extension cable that with 1 5m 3m 5m and 10m for choice You can put the Power System under the screen when choose more than 3m but only can hang it on the Truss or similar supporting if choose 1 5m The power extension cable DC output connects with Power Systems DC output and DC input connects with Data Processor power input WARNING e Electrical
6. ations anchoring method mounting hardware suspending structure and electrical installation is responsibility of the installer WARNING Installing must be carried out by qualified profession only contact you Huasun supplier for assistance if you have any questions about how to install the product safely WARNING A Maximum of three panels in total for Vertical installation 3 84m and 1024 pcs panel for horizontal installation 327 68m Structure Mi Header Installation Figure 2 A Rigging Clamps Can be used to attach a Header C to a Truss One Header can fasten 2 rigging clamps A A1 Fasten Rigging Clamps to Header put through the screw bolt A1 into Header C slot and then tight the Clamps with screw A2 When hang the Rigging Clamps A on the Truss put up the lock stud A2 into the slot and lock tightly B Truss or similar supporting structure can be used to hang the whole led display C Header used to fasten the Rigging Clamps to LED display Hook 07 D LED Display Hook to attach LED Display with the Header C one Header can put through 8pcs hooks The gap among each hook please check the image below esta 72 e572 koosne P 8 6 LF lie ie Figure 3 E Header Connection Bracket to connect the two adjacent Headers C to ensure they are on the same straight line If they are not on the same straight line you can adjust screw A1 to make them on the same line M Pa
7. ay not described in this manual e Install only genuine Huasun parts in or on the product unless an alternative is described in this manual e Do not operate the product if the ambient temperature T exceeds 40 C 104 F PROTECTION FROM INJURY Ensure that any structure used for support as well as all fastening and connecting hardware can hold at least 10 times the weight of all supported devices and eguipment Check that all connection and rigging hardware are securely fastened Do not look at lit LEDs from a distance of less than 40cm without suitable protective eyewear Do not view lit LEDs with optical instruments that may concentrate the light output Ensure at least 30cm distance from LED panel to other things 0 3 gt gt Dimensions TEA AAA 02 Safety Information CeCe A ED T 03 Introduction iaa 05 Packing m ie E E lc o eo A 05 Physical installation a id A E O 07 Electrical Part installation a a di a 10 Service and maintenance cad aii ran 13 Installing Software aria n jj ak aa a a ja dea 1 3 Troubleshooting Tee te ee ee eee er ee ree 14 04 Introduction CE FE RoHS This Installation and Safety Manual explains how to install configure and maintain Rubik series foldable led display The Safety section contains important information about safety precautions The installation sect ion contains details of how to physically install panels and cables and how to connect to control systems and video source
8. connection is completed you must check that all connections are correct and reliable before power All electrical connections must be in operation in case there is no power operation Power is turned on you need to check the grounding eligibility In the power supply must be preceded by a safety device Power can not be rain shower or have water poured on top Don t connect Rubik panel with Local AC power only can connect with Power cable tail of Power signal distributor Power systems can be in series no more than 4 O Rubik panel working voltage is DC 24V ensure connect with PDC 101 Power output cable tail O Power system can connect to AC 90 132V or AC 180 264V 50 60Hz O Local service voltage must conform to Power systems rated voltage and all power systems must be ground electrically 12 Maintenance CE FC RoHS WARNING Before carrying out all maintenance operations must disconnect the power Maintenance must be performed by qualified persons Clean with alcohol cannot use the water Clearing If too much dust wipe the outside of LED modules by a soft cloth with alcohol Replace new LED block if there is damaged LED blocks Buy new led blocks from manufacturer Replacing an LED Block Steps 1 Open the screws at the back of LED block 2 Loose the 6 screens on the sides of block 3 Take out the power panel and led block 4 Place a new LED block into positions on the Panels zz
9. nd observe all warnings in this manual and printed on the product If you have questions about how to operate the panel safely please contact your local dealer PROTECTION FROM ELECTRIC SHOCK e Connect the product to AC mains power within the range 90 260 V nominal at 50 or 60 Hz AN Rubik panels only can connect to Output cable tail of PDC 101 can t connect to Local AC Power and Power signal cable distributor only can connect to Power systems DC24V outlet e Disconnect the entire installation from power before carrying out any installation or maintenance e Always ground earth the product electrically e Disconnect the product from power when not in use e Use only a source of power that complies with local building and electrical codes and has both overloads and ground fault earth fault protection e Connect the Header to power using only the cables supplied by manufacturer for this product Protect power cables from water and rain e Connect no more than 2 powers 2400W in total to one power socket outlets e Before using the product check that all power distribution eguipment and cables are in e perfect condition and rated for the current reguirements of all connected devices e Both end cables of Rubik LED panels are unable to bear large pulling force ensure handle Rubik Panel with Care TECTION FROM FIRE e Do not stick filters masks or other materials directly onto LED modules e Do not modify the product in any w
10. nel Installation Combination Installation Rubik series LED Panel installation must follow the principle of from up and down then from left to right Vertical Combination Installation A When install the panel push downA1 until A2 is fully engaged in the socket A1 downward Push installation devices A2 Locking Handle to stuck the latch on B B Put the B latch into A2 socket then loose A1 till A2 rebounds to press B Install the other module in the same way Notes Latch must be pressed by the Locking Handle to make A rebound Make sure the power cables and the LED Panel must on the same side during the installation rather than in the front of the LED screen Display Image Screen Vertical attachment maximum of three panels in total 08 Horizontal Combination Installation A Left Side LED Display Panel B When install the left panel put your middle finger into the loop and then pull it up until there is a distance between C and D C Locking Handle to engage into the right side locking hook D Right side with locking hooks to engage with C E Right Side LED Panel Notes All the Locking Handles should be in the right side connection holes when the side to side attachment In theory maximum of 1021 modules in total for Horizontal attachment that is the length is 327 68m MM Data Processor Installation A s l gt BL D ai ue Figure 6 Dat
11. rflow around spine Clean spine Panel is too hot Check that ambient temperature does not exceed max Permitted level Contact Manufacturer Display cuts out intermittently Fault on the Data Processor link Inspect connections and cables Correct poor connections Repair or replace damaged cables Have faulty panel or device tested Device on Data Processor and serviced by Huasun service link defective technician or supplier One LED module cuts out LED module incorrectly installed Contact Manofaciuter and connected LED module faulty 14 Incorrect video input or panel settings on System Controller
12. s For information about installing and using the software please refer to attached electrical part user manual Warnings Read the safety precautions one the first two pages before installing this product Unpacking CE FE RoHS Thank you for selecting Rubik Series Foldable LED display Its features 1 New serial of modular Flexible LED based graphic and video display 2 Good flexibility can be curled expand both positive and negative folding combinations assembled into a variety of sizes and shapes suitable for making shaped LED display easy to use 3 Each side of module can be easily combined together into large area LED display easy to install and uninstall Flexible and foldable any irregular shaped LED display is available Easy to set up and take apart large quantity LED display Small volume light weight less than 25mm thick convenient to transport and install Using SMD 3in1 as a light pixel long life low power consumption With light transparent flat features beautiful appearance Simple in use Rich RGB color 9 Color resolution of 16 bits per color 10 A refresh rate of more than 7000Hz vivid and lifelike image M Packing List 32pcs Panels module size is 0 32m x 1 28m According to customers order needs Power 1200 power supply 2sets Data Processor 4pcs HC 103D sending card 1pc without sending controller if work with LED version software Header 4pcs Header hooks 8pcs LED
Download Pdf Manuals
Related Search