TW 512_Manual_EN_V1_130123
Contents
1. TECHNICAL SPECIFICATIONS Suitable For Indoor use IP20 Voltage Input AC100 240V 50Hz Power Consumption 2W Max Frequency Band 2400 to 2483MHz Channels 13 RF Channel Data Rate 250Kbps RF Transmitter Power _18dBm RF Receive Sensitivity _ 90dBm Per lower than 1 RF Antenna Connector amp impedance SMA 50_5 Working Storage Temperature 10 C to approx 50 C Working amp Storage Humidity 20 to approx 90 Dimensions LxWxH 250 x 250 x 350mm Unit Weight 0 36Kg CE Tw512 Manual_EN_V1 cdr P1 4 20130123 16 17 USER MANUAL TW 512 Thank you for purchasing this product For your own safety please read this user manual carefully before you initially start up USER MANUAL TW 512 SAFETY INSTRUCTIONS Every person involved with the installation operation and maintenance of this device has to be qualified follow the instructions of this manual CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual IMPORTANT Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or p2. other successfully You can control the luminaire via controller 4 when you need TW 512 A to connect much more WD 512R you only press the key on the A the direct light A will be quickly strobe status you charge WD 512R B1 B2 B3 instantly Repeat step 3 WD 512T wireless Transmitter and TW 512 Receiver are in communication WD 512TA TW 512B Keeeeeed Transmitter Receiver f f Figure 3 DMX Controller 1 Please see Figure 3 DMX controller luminaire connect wireless controller transmitter WD 512T and TW 512 2 Please charge DMX controller and luminaire firstly and then charge wireless controller A but discharge B 3 Press key of A WD 512T the LED direct light strobe quickly and charge TW 512 B instantly The direct light of B will be in quickly strobe status and match them After 18 seconds direct light Aand B strobe slowly then they connect with each other successfully You can control the luminaire via controller 4 when you need A WD 512T to connect much more TW 512 B you only press the key on the A the direct light A will be quickly strobe status you charge TW 512 B1 B2 B3 instantly Repeat step 3
3. he housing temperature TSURFACE Don t switch the device on and off in short intervals as this would damage the power supply HEALTH HAZARD Never look directly into the light source as sensitive persons may suffer an epileptic shock especially meant for epileptics Always disconnect from the mains when the device is not in user or before cleaning it Please note that damages caused by manual modifications on the device or unauthorized operation by unqualified persons are not subject to warranty Keep away children and amateurs from the device There are no serviceable parts inside the device Maintenance and service operations are only to be carried out by authorized dealers FUNCTION DESCRIPTION T amp R OPERATING INSTRUCTION TW 512A TW 512B Leese Transmitter Receiver f f DMX Controller Figure 1 TW 512 OPERATION INSTRUCTIONS TW 512 wireless control box has two functions for receiving and sending And the two functions can exchange 1 Please see Figure1 make the DMX controller and luminaire connect with A and B from wireless controller Any the wireless controller can regard as A or B 2 Please charge DMX controller and luminaire and discharge the wireless controller A and B at this time 3 Then please charge the wireless controller A at the same time the direct light A can strobe quickly after 8 seconds the direct light would strobe slowly 4 Please press key on the wireless controller box i
4. roblems Keep away from heaters and other heating sources If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard shields lenses or ultraviolet screens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired for example by cracks or deep scratches Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Make sure that the available voltage is not higher than stated in this manual Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord During the initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective DANGER OF BURNING Never touch the device during the operation The housing heats up to t
5. t will be in strobe quickly status Then charge wireless controller box B after 18 seconds the wireless controller box B and A will strobe slowly at the same time the wireless controller A connect wireless controller box B successfully You can control the luminaire via controller 5 When you need transmitter A to connect much more wireless receiver B controller please press key on A the direct LED is under the quickly strobe status at this time you must charge wireless receiver B1 B2 B3 Repeat the step 4 The operating instructions for TW 512 or WD 512T or WD 512R communication each other TW 512 has the functions for sending and receiving but WD 512T and WD 512R has only sending functions or receiving functions TW 512 Transmitter wireless controller box A and WD 512R Receiver wireless controller box B are in communicate TW 512A WD 512R B ivscesd Receiver Transmitter f f Figure 2 DMX Controller 1 Please see Figure 2 DMX controller luminaire connect with TW 512 and WD 512R 2 Please charge DMX controller and luminaire and then charge wireless controller box A and B 3 Wait for the direct light of TW 512 A entering slowly strobe status when pressing the keys the direct light strobe quickly at the same time please press keys of WD 512R direct light B will be in strobe quickly status and match them after 18 seconds direct light A and B will strobe slowly then they connect with each
Download Pdf Manuals
Related Search