User Manual - Box Design by Pro
Contents
1. y Inputs Make all connections whilst the amplifier is disconnected from the power supply Take care to connect the left and right channels correctly The right channel is usually marked red the left channel black or white The red speaker terminals carry the positive signal the black speaker terminals the negative signal Make sure the polarity of the connection is correct at each end of the cables Only connect one loudspeaker with an impedance not less than 4 ohms per channel Never use any other power supply than the one supplied with the unit Line level sources such as CD player radio or TV can be connected to the input sockets marked IN1 or IN2 Connection to the speakers The output terminals accept loudspeaker cables terminated with 4mm Banana plugs spades connectors or naked wire Record output connecting a headphone amplifier Record Out connects an analogue record device ore a Pro Ject Head Box headphone amplifier nes Record Out provides a fixed output level 2 Pro Ject Audio Systems gt Stereo Box S 25 37W from S N C35573 Revision 2015 11 05 Mains power connection The unit is supplied with a power supply suitable for your country s mains supply Check the label before connecting to ensure compliance with the mains rating in your house Connect the low voltage plug from the power supply to the Power 20V DC socket before connecting the power supply to the mainsl Remote control ON OF2. lo BC BY PRO JECT AUDIO SYSTEMS INSTRUCTIONS FOR USE Pro Ject Stereo Box S Dear music lover thank you for purchasing a Pro Ject Audio Systems amplifier In order to achieve maximum performance and reliability you should study these instructions for use carefully V 3 Warning of a hazard for the user the unit or possible misuse Important notice Safety instructions y Please note that the back side of front panel edges can be sharp Please handle carefully AC outlet voltages vary from country to country Before connecting to the mains make sure that the voltage in your area meets the voltage requirements printed on the power supply The power cord is used to disconnect the unit from the mains Make sure that the power cord is easily accessible at all times Never handle the device the power cord power supply while your hands are wet or damp Avoid letting liquids enter the device or the power supply Never place any item containing liquid such as a flower vase on or near the device Never spill any liquid on the device or the power supply Never place any naked flame sources such as lighted candles on or near the device The product shall not be used in damp or wet locations next to a bathtub sink swimming pool or any other similar conditions Connectors 3 Record Dut a N i CE cA Power SPN S 4 i y N 4 Aine d IN1 SK C O ed Ject Audio Systems Vienna Austria
3. F turns the unit on or back into standby co and adjust the sound volume and on select the inputs Front panel controls 1 2 080 t eee To switch on from standby or to standby The push button press and hold to switch into standby mode on the left hand side of the front panel turns the unit on or back into standby The blue LED above the stand by push button shows that the unit is switched on Input selector After the unit is powered on pressing the push button on the right selects the In 1 and In 2 inputs in turn The optional input expander Pro Ject Switch Box S provides three more inputs For further details please see the user guide of the Pro Ject Switch Box S Volume Adjust the volume to the desired level using the large knob on the front panel Pro Ject Audio Systems Stereo Box S 25 37W from S N C35573 Revision 2015 11 05 3 Replacing batteries Proceed as follows e Unlock and slide open the battery case cover e Replace the battery Make sure the battery is the right way round e Close the battery case cover Battery type 1 x CR2032 3V or 1 x CR2025 3V Do not dispose the batteries as ordinary domestic refuse Please dispose your exhausted batteries at the appropriate collection sites usually located at supermarkets and drugstores Technical specifications Pro Ject Stereo Box S Power output Frequency response Channel separation Noise floor THD Gain
4. Line level inputs Input sensitivity Input impedance Record Out Speaker connectors Outboard power supply Power consumption 2 x 25W 37W at 8 ohms 4 ohms both channels driven 5Hz 20kHz 0dB 0 5dB gt 65dB at 20kHz gt 90dB A weighted lt 0 07 at 15W 31dB 2 pair RCA phono sockets 350mV 50kohms 3 pole 3 5mm co axial jack 4mm banana plugs spades connectors or naked wire 20V 3A DC suitable for your country s mains supply 3A DC lt 1W in standby Replacement battery remote control 1 x CR2032 3V or 1 x CR2025 3V Dimensions W x H x D D with sockets 103 x 36 x 104 122 mm Weight 720g without power supply Service Should you encounter a problem which you are not able to alleviate or identify please contact your dealer for further advice Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions Neg for use Modification or change to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawful rights of the customer Pro Ject Audio Systems is a Registered Trademark of The information was correct at the time of going to H Lichtenegger press The manufacturer reserves the right to make This guide was produced by Pro Ject Audio Systems changes to the technical specific
5. ation without prior Copyright 2015 All rights reserved notice as deemed necessary to uphold the ongoing process of technical development 4 Pro Ject Audio Systems gt Stereo Box S 25 37W from S N C35573 Revision 2015 11 05
Download Pdf Manuals
Related Search