User Manual - biznetmall
Contents
1. the following settings can be selected Low tone 1 2 1 is low tone turned off and 2 is low tone turned on oOlD1 setting of the position of zero for the indication of ID1 it can be moved to the left or to the right along the scale I e if an object has an indication for ID1 2 if 0ID1 is decreased with 4 units the indication for the same object will become 2 In this way some undesired alloys stained iron items or caps and other objects of foil can be avoided and the device to register them with negative values by preserving the positive indications for the more ferrous objects coins rings etc olD2 analogue to oID1 but for the indication of ID2 Discr 1 2 3 4 choice of a sub mode of AUTO DISCR auto discr rng 1 2 3 choice of allowable range for the value of ID1 upon memorization of a definite object rng2 1 10 choice of allowable range for the value of ID2 upon memorization of a definite object The AUTO DISCR mode is suitable when the background of the soil is negligibly small and doesn t change in considerable degree the signal received upon localization of a metal object I e in it one can work on low mineralized or sandy soils At a higher mineralization of soil it gives a signal which can increase considerably especially at approaching of the coil to cling to ground surface Highly mineralized soils especially when con2. 1 If for Thresh a value of 6 has been chosen then the device is going to react with sound at a considerably stronger signal value greater than 6 Greater values of Thresh can be selected if the general signal from the background of soil changes within wider limits in order the device to be calm aiming a sound signal not to be produced which is not due to detected metal but the greater the value of Thresh the more sensitivity of the device decreases At a presence of de balance one has to press shortly ON OFF CLEAR as at this the searching coil has to be close to the ground at the distance of search to be Continuous pressing of ON OFF CLEAR for more than 4 sec will turn off the device as this is accompanied by 3 short sound signals Should within the range of the coil there falls an object it produces a signal which is displayed on both indicators ID1 and ID2 and on the indication Level of the intensity of the signal Should this signal is louder than the threshold chosen of the sound Thresh a sound is heard with a frequency which depends on the sound level The greater the signal from an object the louder the frequency of sound This is a very convenient mode for precise localization of the location of an object Pinpointing a Target A good method for pinpointing is X ing the target with the search coil Remember that the target s response sound is always greatest when the target is d
3. 12 and for ID2 they will be 3 units under and 3 units above the memorized value of 10 Upon following pressing of VCO DISCR the device is switched into auto discr AUTO DISCR with sub modes reject REJECT at which definite undesired objects can be memorized and eliminated TT In the auto discr reject mode the device memorizes only the purity coefficient ID1 of a metal and in the AUTO DISCR REJECT mode it memorizes both coefficients for purity ID1 and for magnetism ID2 The display shows an indication for example R 9 28 corresponding to ID1 9 and ID2 28 In this case the device will eliminate signals from a located metal only if both memorized coefficients coincide I e ti will operate more precisely but beside rng1 the value of rng2 will also be the one that will matter as ID2 is also taken into consideration The setting of rng2 refers to the indication of ID2 and is analogue to rng1 but rng2 can change within the limits 1 10 For example if a metal with coefficients R 9 28 has been memorized and for rng1 a value of 1 has been chosen and 3 for rng2 the device will react only to metals with signals from R 8 25 to R 10 31 or the ranges of location will be for ID1 with 1 unit under and 1 unit above the memorized value 9 and for ID2 th
4. Level what is the indication of the signal of the soil Upon a signal from the soil of up to Level 20 one can operate in NORMAL DISCR mode but at higher levels of mineralization one has to switch to auto diser or AUTO DISCR which features are explained below Searching metal objects is made by moving search coil toward ground surface fig 1 fig 2 Fig 1 Wrong Correct Fig 2 The search coil should not touch the ground during your sweep The pole length should be adjusted to allow this without having to lift the detector with your elbow or shoulder The search coil should rest about one inch above the ground while you are standing erect The angle of the search coil should allow the bottom to be parallel to the ground 2 1 Setting of working parameters in VCO mode setting of the threshold of co working of the sound Thresh this is the level of signal after passing of which a sound is heard The device may be set at such strength of signal to react with z sound This is done with change in the parameter Thresh For this purpose through the buttons lt and gt desired value can be selected from 0 to 20 The lower the value of Thresh the greater the sensitivity of the device For instance if at a balanced device the constant signal from soil is 1 and we have chosen for Thresh a value of 1 then a sound signal is going to appear when the general signal becomes greater than
5. has a built in storage package 14 4V 2 2Ah which is able to provide 10 15 hours of working process without any interruption depending on the chosen power and the type of the used search coil Bigger coils consume more power and thus the working time is shorter 14 The accumulators status is shown on the first row on the right as per cents of the capacity 0 100 When the capacity decreases below 0 it will show Low bat and if fully charged batteries or if using external supplying block with higher voltage it will show The charging is automatic and begins when the device is SWITCHED OFF and you plug the charger into the charging jack of the back panel of the device The jack cage is and the middle terminal is During charging on the display you will see transitory and maximum voltage of storage batteries their temperature as well as the charged so far capacity and on the lower row of the display Charging The charging continues till the moment when the batteries reach their maximum capacity which also reflects in increase in the temperature When reaching their full capacity and increase in the temperature up to 40 C the charging stops and down on the display you will see FULL At the same time the device will start to make short sound signals Charging depending on the level of discharge of the batteries It s not necessary to keep eyes on charge device because it is supplied with auto
6. ID2 are depicted which at registering of ferrous magnetic metal have negative values and at nonferrous non magnetic metal positive values ID1 is a coefficient of purity of metal and ID2 coefficient of magnetism Most often upon localization of nonferrous metal ID1 and ID2 have great positive value for example 13 and 9 Upon localization of magnetic ferrous metal they have great negative value for example 4 and 20 Upon localization of foil aluminium and unstained iron ID1 and ID2 have their negative values and both of them have great positive values express when the nonferrous metal is pure without admixtures and alloys gold bronze copper silver Upon localization of highly stained iron ID2 has great negative value for example 15 20 and the indication of ID1 is around zero or 1 2 They show that there is no sense this signal to be checked where it comes from Foil aluminium and aluminium alloys usually provoke signals around zero for example ID1 2 and ID2 5 One has to also take into consideration that these indications can change through setting of oID1 and oID2 of the menu ID1 and ID2 can have different values if within the range of the coil there is both nonferrous and ferrous metal or some alloy The ID1 and ID2 coefficients appear only upon localization of metal also in the VCO mode but in that case sound is multi frequent one for more
7. and always fill back in the holes you have dugged out 7 GUARANTEE The detector STINGER 2 is offered with 2 years of guarantee of electronics labor and materials used for harms which are not caused on purpose or irresponsibly We can upkeep your device after period of guarantee if it is necessary 8 Protecting your investment Often detectorists are disappointed when their new detector slowly becomes less and less responsive and seems to have lost some of its original peak performance You can help avoid this from happening to your detector by following these basic care and protection guidelines Operate your detector exactly as recommended in this Operator Instruction Manual The search coil cable is hard wired to the search coil and protected by a strain relief It is very important that the strain relief remains intact and should never be adjusted or tampered with Keep cables properly wound around the pole stems and protect them during use Floppy pinched or cables that become snagged during use may short causing erratic noises or unnecessary replacement of the search coil Sweep the search coil carefully especially when using around rocks and building foundations Avoid hitting the search coil against hard solid objects and surfaces Keep your search coil slightly off of the ground during the sweep especially when using in gravel or hard rocky dirt Remove and clean out scuff covers periodically to avoid buildup
8. can not solve the problem contact the service station office of the company manufacturer or the local distributor 6 3 During detection the device does not work stable makes strange sounds which are not due to a metal detection It might indicate for irregular electromagnetic external interruptions False signal or instability can often be caused by situations outside of the detector For example electrical interference from power lines or other high power transmitting devices Often these devices can be identified sometimes they can not problems with the aerial cable disconnected conductor a shot circuit or bad connection in the coupling If disconnected conductor or shot circuit in the cable on the lower row of the display you will see COIL ERROR It is possible after continuance work and many times of switching on and off the cable s coupling to the jack box the contact between them to be destroyed There are 4 terminals with sightholes in the jack of the back panel of the device Put something sharp like a knife or a screwdriver in the sightholes and make them wider Thus the coupling will fit better into the jack which will improve the contact between them It is possible in the presence of some kind of dirty like dust or moisture to clean the terminals with cotton wool and alcohol If you can not solve the problem contact the service station office of the company manufacturer or the local distributor 6 4 The device work
9. comfortable determination of the location of the object Upon localization of an object if the common signal becomes louder than Level 350 the sound changes into a very low deep tone and on the first 2 rows to the right there appears the following discr overflow The digital indication continues to track the increase and if the level Level 1000 of overflow is achieved then the sound changes into a very high signal tone and the display shows OVERFLOW on the 4 row of the display In the modes of discrimination Thresh determines the minimum level of the signal after which there starts calculation of the coefficients ID1 and ID2 It cannot have values smaller than 5 in order to cooperate the sound signal of the discrimination at a comparatively low signal from the object This is developed to avoid eventual error upon discrimination of very weak signals In NORMAL DISCR mode on the 2 row to the left of the display the balance indicator appears l l for the background of the soil and shows whether the device is balanced at lack of signal At a balanced device and lack of metal objects within the range of the coil the indicator has to have 2 equal levels both from the left and the right side of 9 the symbol If there is a difference in both levels balance of the device should be performed through POWER CLEAR In the discrimination modes with the pressing of SELECT
10. mode and the slowest one Static 4 Dynamic are dynamic modes of operation with different speed of searching The difference in these modes is in the time for automatic nullification of appeared signals i e the device is constantly additionally setting itself but with various speed in various modes The fastest one is the Dynamic 1 mode and the slowest of all the dynamic modes is Dynamic 4 In these modes the device reacts to metal objects within the range of the coil only upon movement of the coil above them 4 row to the right Level the level of signal from the registered metal in figures from 0 1000 If there is signal of metal within the range of the coil disturbances or influence by soil upon short pressing of ON OFF CLEAR this indication will become 0 After removal of the source of the signal from the coil range indication will become of negative value In order to be nullified you have to push again ON OFF CLEAR During searching above ground surface the indication for the level of signal hesitates 1 0 1 or more depending on the 4 degree of mineralization of soil For example in order to understand how strong is the signal from the soil on a definite location one can lift the searching coil in the air and the device to be nullified with short pressing of ON OFF CLEAR Then the coil is brought close to the ground surface and one can se opposite
11. multi frequency sound which also appears as common mode of searching for all metals 1 Assembling of the device Assembling the STINGER 2 is simple and you don t need any special tools When use the round coil 45cm or 22x32cm The bearing rod is assembled by inserting of the lower part into the upper one Choose the desired length of the whole construction and the fixing clamp is tightened between both parts of the bearing rod The lower part of the bearing rod is put with the opening between the ears of the coil and the plastic bolt is tightened by choosing the 2 position of the coil to be parallel to the ground surface Don t over tighten the plastic bolt and nut to not damage the threading of the bolt The coil cable is wind up tightly around the bearing rod and is switched to the terminal of the monitor unit Upon switching of the cable of the coil to the monitor unit tighten the well the metal nut of the coupling to the terminal of the box Upon switching off unscrew the nut completely and pull out the coupling without pulling or twisting the cable of the coil This way you will prevent the cable and the conductors in it from breakdown or short circuit Finally adjust search coil angle to your preference and you are ready NOTE Do not allow the cable to flop loosely over the search coil Since the detector is sensitive enough to see the tiny wires in the cable a floppy cable can cause false signals as the search c
12. of mineralized dirt particles which will affect performance gt The search coil is waterproof and can be submerged in either fresh or salt water After the search coil is used in salt water rinse it and the lower stem assembly well with fresh water to prevent corrosion of the metal parts 17 The searching coils and frames are waterproof but the electronics are not so always prevent any moisture or water from entering the control housing and never allow the cable connector to become submerged in water If working in or near water or if there is a possibility of rain use a protective weather resistant pouch or plastic bag to cover the control housing Make sure it can breathe in order to ensure against condensation buildup inside After each use clean the detector with a soft cloth to remove dust moisture or other contaminants When transporting the detector in a car during hot weather store it on the floor of the passenger compartment if possible Using a carry bag gives additional protection In any case never allow the detector to roll around unprotected in the trunk or back of a pickup truck Protect your detector from dust moisture and extreme temperatures during storage Treat your detector as you would any sensitive electronic instrument Though ruggedly constructed and designed to withstand the demands of normal treasure hunting proper care is essential www biznetmall com stinger2 18
13. accompanied by sound signal One has to also take into consideration that when using the fast modes 1 and 2 whether Dynamic or Static the consumption of the device is greater than in slow modes i e in slow modes the device is more economic and can work longer with one charging of the accumulators Fast modes of searching are suitable for searching in polluted sites and when using the smaller searching coils It s preferred you to operate in modes 3 and 4 but if you wish to operate with the high speeds it is recommended that you decrease the power emitted to P1 and the sensitivity to be increased to S3 In this way the consumption of the device will be decreased without sensibly decreasing the depth of searching By pressing of SELECT you enter a menu where the following settings can be made Coil 1 2 3 4 choice of a program for searching coil 4 different programs can be memorized for 4 different types of coils Power 1 2 choice of power of emission 1 is decreased power and 2 is normal Sens 1 2 3 choice of sensitivity of the device Choice among 10bit 11 bit or 12bit ADC After each change of some of these 3 parameters the device automatically restarts in order the respective settings to be loaded according to the selected values rejF 0 15 through this parameter the device can be adjusted to decrease its sensibility to smaller objects without losing its sensit
14. amics or some iron has been memorized with own signal of 28 the device will not react to any signals smaller than 28 and each signal greater than 28 will be registered with sound as the objects with more positive signal from 27 to 0 will be signalized with a low tone and all positive ones with high tone If from the menu for Low tone a value of 1 has been selected for the negative signals there will not be low tone and the device will react with high tone only for the positive signals i e for the nonferrous metals Analogue is the operation of the device also when working in an auto discr mode all metals with a signal more positive than the memorized one will be signalized and all having values lower than the memorized will be eliminated The difference between the auto discr and AUTO DISCR modes is that at a selected mode with capital letters the device operates more effectively for bigger objects and can successfully memorize and eliminate undesired bigger objects or more active soils in REJECT mode When operating in auto discr reject mode the device can successfully memorize and eliminate undesired smaller objects for example wire and small nails and to effectively search for coins rings or other small objects but in this mode very big objects or very high mineralization of soil can provoke undesired misleading signal In such cases i
15. ey will be 3 units under and 3 units above the memorized value of 28 In the sub modes reject REJECT one can also additionally select auto discr and AUTO DISCR to operate with extended range This is indicated on the display with a at the end of the inscription auto discr and AUTO DISCR In the modes with at the end auto discr and AUTO DISCR the common signal is analyzed and at a change one calculates what part of it is due to the background of the soil and what part is provoked by another object That is the way of calculation what is the signal only from the object it is close to that one if soil doesn t have its own background or the object is situated in the air These modes are most suitable for searching of ferrous objects among iron waste or in highly mineralized and ore soils as well as under active stones ceramics or slag The difference between both modes AUTO DISCR and AUTO DISCR is that that in the AUTO DISCR mode the device memorizes both coefficients for purity of metal ID1 and for magnetism ID2 while in the AUTO DISCR mode it memorizes only ID2 and eliminates undesired objects only by the magnetic properties This is the mode in which one can successfully register non magnetic metal objects between iron 12 items or under active stones and highly mineralized soils In this case if for example an object stone cer
16. ge increases with 3 more units under the memorized value and 3 units over it The device will not have sound indication of any signals smaller than 9 and greater than 15 The difference in the sub modes accept and ACCEPT corresponding to auto discr and AUTO DISCR expresses in that at auto discr the device memorizes only the coefficient for purity ID1 of metal and the display shows for example accept 12 At an AUTO DISCR mode the device memorizes both coefficients for purity ID1 and for magnetism ID2 An indication appears on the display for example A 12 10 corresponding to ID1 12 and ID2 10 In this case the device will produce a sound from located metal only if both memorized coefficients coincide I e it will work in a more precise way but beside rng1 the value of rng2 will also be the one that will matter as ID2 is also taken into consideration The setting of rng2 refers to the indication of ID2 and is analogue to rng1 but rng2 can change within the limits 1 10 For example if a metal with coefficients A 12 10 has been memorized and for rng1 a value of 1 has been chosen and 3 for rng2 the device will react only to metals with signals from A 11 7 to A 13 13 or the ranges of location will be for ID1 with 1 unit under and 1 unit above the memorized value
17. ingle sound This lasts for 3 4 sec then it is followed by a double short sound and the device is turned on in general mode of VCO or last used mode If you wish to work in a mode of discrimination 3 DISCR you have to push the button VCO DISCR at which the device is switched into discrimination mode and the display shows NORMAL DISCR 2 Working with the device in VCO mode In this mode the display shows VCO Constantly shown are the level of signal in digital or graphical appearance the capacity of the accumulator chosen power the sensitivity the level of co working of the sound and the working mode as follows 1 row to the left the working mode VCO the chosen power P1 or P2 and the sensitivity of the device S1 S2 or S3 2 row to the left capacity of the battery in percent 0 100 or time to work 3 row to the left the mode and the speed of searching Dynamic or Static The device can work in 8 modes of speed of searching 4 static for precise localization of an object Static 1 Static 4 and 4 dynamic for searching while moving Dynamic 1 Dynamic 4 static are static modes of searching i e the device constantly reacts to metal located within the range of the coil They are suitable for localization of the precise position of an already located metal and one can also work in those modes permanently The fastest one is Static 1
18. irectly under the center of the search coil To X a target sweep the search coil over the target from side to side and then from front to back until you can identify the center of the X the spot on the ground where the target response sound is the greatest Pinpointing a target in Discriminate Mode is probably best done by X ing as well Remember that the detector will beep just as the target passes under the center of the search coil Slowing the sweep speed down will help you pick out the center of the X but remember that the search coil must always be moving slightly for target detection Another easy method is to sweep the coil from side to side across the target in very short sweeps as you slowly move forward and backward across the target Slow down the sweep rate and 6 shorten the sweeps until you just barely get a response at one spot The target will be directly below the coil center at this response time fig 3 Target i3 Upon short pressing of the MODE button the indications of the discrimination ID1 and ID2 turn on as well as the intensity of the signal located in digital or in graphic appearance In graphic form the indicators may show positive or negative levels respectively increasing to the right or to the left from the dividing zero point of each of them Continuous pressing of MODE for more than 3 sec switches between Dynamic or Static mode of searching as this is also
19. ivity to bigger ones This has its effect only in the mode with capital letters AUTO DISCR The greater the value of rejF the smaller the sensitivity to smaller objects This function can be successfully used for elimination of the surface layer of soil 1 e there to not be signals from smaller objects on surface but to only react to deeper and bigger objects dspB 1 2 Clear cap I capacity of the battery in percent 0 100 2 working time Clear cap clear the capacity of the battery LCD 0 7 light of the display 0 turned off and 1 7 various brightness of light If one accidentally pushes SELECT and it is not necessary any changes to be made on the settings the device can be turned again into operation position through pushing and holding of SELECT for 3 sec 2 2 Setting of the operating parameters in DISCR mode STINGER 2 has 2 basic modes of discrimination NORMAL DISCR and AUTO DISCR which are selected through pressing of button VCO DISCR as AUTO DISCR has 8 sub modes of operation AUTO DISCR has the following sub modes auto diser and AUTO DISCR as each of them has the function accept ACCEPT and reject REJECT Upon activated discrimination beside the intensity of signal upon location of metal on 1 and 2 row of the display to the right both coefficients ID1 and
20. matic turn off and batteries couldn t be damaged no matter how long they will stay in the charge device When they are ready pull the device out of the electric net and take the jack out of the CHARGE NOTE Don t unplug the charger if charge process is not finished Always charge device s storage batteries ONLY with the paired chargers to it Thus you will prevent damages or confusion between and because the use of other chargers or adaptors may lead to irretrievable damages in the batteries 6 Possible problems during exploitation of STINGER 2 6 1 When switching it on you can not hear a sound there is no information on the display no indication that the device is switched on It might indicate for storage batteries are dead usually after a long period of time Charge the batteries with the charger If the problem is not solved contact the service station office of the company manufacturer or the local distributor the accumulator block consists of 12 elements 1 2V 2 2V connected in series If just one of them 15 is damaged the connection between them will be destroyed and practically the device will be left without power supply 6 2 The working depth is significantly shallower than the normal It might indicate for storage batteries could be dead pay attention to the shown for the capacity of the storage batteries If it is charge the batteries with the automatic charger If you
21. oil senses the moving wires The searching frame coil is approached to the surface of earth by paying attention to avoid presence of metals within its range The cable is sub connected to the device Upon switching of the cable of the searching frame to the monitor unit tighten the well the metal nut of the coupling to the terminal of the box Upon switching off unscrew the nut completely and pull out the coupling without pulling or twisting the cable of the coil This way you will prevent the cable and the conductors in it from breakdown or short circuit When use the search frames Ixlm or 2x2m The search frame should be held approximately 4 to 6 inch 10 to 15cm to ground surface while searching Do not allow one end of the frame to be higher than the other Make sure that no large metal objects are close to the search frame for initial adjustment Also check your shoes or boots since most of them contain metal parts and you would receive a signal response any time you step near to the coil In order to avoid interference of the metal parts of the electronic unit be sure to carry the STINGER 2 on the side of your body that is away from the search frame The device is switched on through pressing of ON OFF CLEAR and you see on the display Start Detector the serial number of the device and the software version Starts balancing to the ground conditions during which time the display shows CLEAR and you can hear a s
22. s only with headset and when working with amplifier you can not hear a sound Usually that happens when the headset jack is damaged In that case contact the service station office of the company manufacturer or the local distributor to change the jack 6 5 When switching on the charger to charge the storage batteries you will see on the display FULL Usually that happens when the device was kept in the cold and the battery temperature is around or below 0 C If the microprocessor can not define the batteries temperature you can not strat the charging and on the display you will see FULL Leave the device in a warm premise and wait till the temperature of the batteries increases up to 5 6 C If you can not solve the problem contact the service station office of the company manufacturer or the local distributor and do not charge with any other devices or ordinary adaptors 6 6 Batteries charge quickly and after that during the working process they go dead 16 quickly Usually that happens when the batteries are really old and need replacement Contact the service station office of the company manufacturer or the local distributor for change of the storage batteries The Manufacturer trader does not bear any responsibility if you use the device in violation of the law on archeological or forbidden for search places as well as on private property without the knowledge or the permission of the owner Protect the environment
23. se the signal from the soil is undesired If at a definite point the signal from the soils changes within wide limits for example REJECT 20 40 60 it is recommended that the minimum deviation is memorized 20 or one to work in the dynamic modes Dynamic in which the device constantly balances itself 4 The detection depth depends on the following size shape and location of the object in the soil The bigger the reflecting surface of the object the deeper it is to be found soil composition and mineralization level the drier and more homogeneous the soil the easier it will be to adapt the device and for the device to detect deeper Under stones dry sand or in clay utensil metals are easier to be found than in freshly dug out or damp soil the longer the object has been in the soil the easier it will be to be found as a result of the good contact with the soil type of detecting coil The bigger the diameter of the coill the deeper it will be able to detect metals operator s experience and skills You can do field tests by yourself using the device if you bury different metal objects in different depth but you should leave them in the ground for at least 3 months Thus the test results will be more reliable You should mind the soil type and the moisture composition in it Best results are received when the soil is dry 5 Charging storage batteries and indications for their status STINGER 2
24. t is recommended the device to operate in AUTO DISCR mode The modes with can be selected by pressing the button SELECT until the discr parameter appears and one has to choose either discr 3 for auto discr or diser 4 AUTO DISCR Switching between the modes with and without can be done also during work with pressing and holding of the buttonh VCO DISCR for more than 3 sec but this can be done only in the sub modes reject REJECT 3 Balancing to the background of the soil in the discrimination modes Usually light weak mineralized soils have their own signal of up to Level 15 20 On them one can work in a NORMAL DISCR mode and the only balancing which can 13 be performed in this mode is to press ON OFF CLEAR for short as the searching coil has to be close to the ground surface at the distance at which one will search In this way the signal from the soil is perceived as zero and each change provoked by a metal object will provoke a sound signal with high or low tone according to the type of metal At higher levels of mineralization presence of moisture active stones or ceramics most suitable for balancing is the AUTO DISCR REJECT mode as most often signals from the surface of the ground are positive and the balancing of the device to the soils is analogue to the memorization and elimination of undesired objects in that ca
25. taining a considerable amount of moisture additionally increase the common signal and it can have great values If in such type of soil there is nonferrous metal it will change the common signal to more positive values but to overcome the background of the soil the signal to the object will have to be considerably stronger 1 e the sensitivity because of the background will decrease For such cases suitable are the auto discr AUTO DISCR modes The next mode of discrimination is auto diser AUTO DISCR with a sub mode accept ACCEPT In this sub mode the device will not produce any sound signal until it memorizes a definite nonferrous metal and the indication on the 3 row to the right of the display is accept or ACCEPT The memorization of a definite metal 10 is done as follows the Auto GEB button is pressed and held and to the searching coil a definite type of nonferrous metal is approached the indicators for the type of metal ID1 and ID2 show the type of metal and against accept ACCEPT a definite figure is depicted as per the type of metal for example accept 12 In this case the device will react only to metals with own signal 11 12 or 13 if for the parameter rng1 a value of 1 has been chosen If the value of rng1 increases to 3 the device will react with a sound and at signals of 9 to 15 i e the ran
26. www biznetmall com stinger2 STINGER 2 User s Operating Manual MIXON STINGER 2 ON OFF yzl CLEAR Pulse induction metal detector In order to use the device for a maximum long time and without problems as well as to be able to use all of its options please read carefully the whole instruction manual and observe the directions in it The standard set of STINGER 2 comprises searching frame 1x1m monitor unit with built in accumulators recharge device for 220 V recharge device for 12 V detailed instruction manual for operation If any of these items are missing immediately inform us or our autorized dealer where you purchased your detector STINGER 2 has the following buttons for control Button ON OFF CLEAR for switch on and switch off of the device and for automatic nullification to the soil conditions Buttons SELECT and gt serve for work with the menu and the settings choice of modes of discrimination and movement Button Auto GEB serves for automatic setting of the device to earth conditions of a working terrain and for memorization of definite objects or soil Button MODE used for switching between digital and graphic display of the indications for discrimination ID1 and ID2 and switching between the Dynamic and the Static mode Button VCO DISCR serves for switching between the mode of discrimination and the VCO mode
Download Pdf Manuals
Related Search