PDF - Daisy Data Displays
Contents
1. 4823AC User s Manual T DAISY DAIA displays inc Trouble Shooting The computer will not start Power Requirements Verify power source Model 4823AC See model Nominal Voltage 120VAC requirements Current Warm Climate 75 Amps Nominal Current Cold Climate 3 35 Amps Nominal Can the power source meet the requirements No LE power SH Note 1 Yes The computer is not permitted to start if the temperature drops below 0 Celsius inside the cabinet and will remain off until the temperature rises above 6 Celsius Is the temperature in the unit below O elsius See not No Yes Note 2 The heaters turn on when the internal temperature drops below 8 Celsius and will remain on until the internal temperature rises above 16 Celsius Are the heaters warm No Heater thermostats may be bad Yes Y Wait until the temperature inside the unit warms above 0 Celsius Yes s the power good from the Surge Suppressor Did the computer start Replace Surge HR No Suppressor Yes v Yes This is normal operation for a cold climate Figure 13a Power problem flowchart 3 26 2012 4823AC User s Manual 8 DAISY DAIA displays inc Trouble Shootin Manual start Open the cabinet door and press the Power Reset buttons2. DAISY DAIA gispolaus inc 4823AC User s Manual V 1 0 DAISY DAIA j cisotaus INC Disclaimer 4 FCC Warning DISCLAIMER Daisy Data Displays Inc makes no representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied war ranties of merchantability or fitness for any particular purpose Further Daisy Data Dis plays Inc reserves the right to revise this publication and to make changes to its con tent at any time without obligation to notify any person or entity of such revisions or changes Further Daisy Data Displays Inc makes no representations or warranties with respect to any Daisy Data Displays manufactured equipment and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose Further Daisy Data Displays Inc reserves the right to make changes to any and all Daisy Data Displays manufactured equipment at any time without obligation to notify any person or entity of such changes FCC WARNING Computing devices and peripherals manufactured by Daisy Data Displays generate use and can radiate radio frequency energy and if not installed and used in accor dance with the instructions in this manual may cause interference to radio communica tions Such equipment has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 o
3. THE UNIT WLL TURN ON AT 6 C gine Daisy Data Displays Inc ld ege ege i is MA amp BLOCK N A ermm OT MOD 482 3A Da aaa TD Rescue 030100050 Le KS LA 3 26 2012 4823AC User s Manual 13 W e 15 LCD WITH VIEWING WINDOW CHOICE OF LEXAN SAFETY GLASS OR TOUCHSCREEN 14 BUTTON MEMBRANE KEYPAD USER DEFINED LEGEND 3 26 2012 DAISY DATA displays inc an 2 x LOCKING LATCH W ISOMETRIC VIEW FRONT ILOCK OFF GLAND PLATE CUSTOMER DEFINED VO ca LIN 2 REAR I ISOMETRIC VIEW Drawing 1 REVISIONS D COOLING FINS XTERNAL MOUNTING HOLES 14 x 1 4 20 UNC 2B C a wd B PRELIMINARY DRAWING DIMENSIONS MAY BE 4823AC User s Manual CHANGED TO MEET CUSTOMER SPECIFICATIONS TOLERANCES APPROVAL DIMENSIONS ARE Fa IN INCHES FRACTIONS 132 DOCUMENT it CONS DECIMALS PROPRIETARY TO DAEN bat XX t 03 i TRS DOLUWENT t PR XXX st 015 EXCEPT AG AUTHONZED BY THE CORPORATION IN WEE TING ANGLES DPECIFCATIDUS ANE SUBJECT 1 TO CHANGE WITHOUT NOTICE 2850 Lewibery feed York Kawan PA 17370 3 disalays imC Phone 717 922 2000 Yul os a wwe har net MODEL 4823AC COMPACT NON INC 15 LCD CAST AL PART NO DAG NOJREY 4823AC 8801 14
4. 17 50 Width W 14 50 Height H2 8 56 Depth D1 1 56 Depth D2 9 16 View Height VH 12 16 View Width VW 60 65 Lbs Polycarbonate Standard 120 VAC 3 35 Amps 90 W 402 W w heaters FLAT PANEL SPECIFICATIONS Maximum Resolution Dot Pitch Color Depth Viewing Angle Typical HxV Brightness Standard ENVIRONMENTAL Shock IEC68 2 27 Vibration lIEC68 2 6 Operating Temperature Storage Temperature Relative Humidity Listed Approvals 1024x768 0 297mm 24 bit 80 Left amp Right x 80 Up amp 60 Down 600 nits 15G bi directional impulse 11 msc non operational 3 axes 3 GRMS operational 5 2000 Hz 5 GRMS non operational 5 2000 Hz 3 axes 40 150 F 40 65 C 40 150 F 40 65 C 10 95 Non Condensing EExnA IIC T4 ExII36 COMPUTER SPECIFICATIONS Motherboard Storage Standard CPU Standard Mini ITX SBC Integrated Graphics 2 PCI Slots Dual 10 100 Base T Network Interface 4GB Flash Drive 1GB Ram Pentium M 1 8 GHz Contact your Daisy Data Displays representative for info on the latest CPU memory and hard drive options Specifications are subject to change without notice 3 26 2012 CONNECTIONS From Motherboard 1 Serial 1 Parallel 4 USB Audio In Out Network Game Port PS 2 Keyboard Port PS 2 Pointing Device AVAILABLE OPTIONS 451 Capacitive Touch Screen 820 Bezel 821 Sun Visor 823 Windows XP 9137 Yoke Mount
5. Figure 1 Front View 1 Door 4 Display 2 Touch Screen 5 Keypad 3 Latches Figure 2 Unlocked Latch Figure 4 Keypad 3 26 2012 4823AC User s Manual DAISY DATA displays inc err Enclosure Callout Figure 5 Top View 1 Accessory Mounting Holes 74 20 threads 2 Serial Identification Label DO NOT REMOVE Figure 6 Latch side KG E E KA KA Ki E EAE LE BA ZA Figure 7 Rear View 3 Accessory Mounting Holes 74 20 threads 3 26 2012 4823AC User s Manual 2 DAISY DATA ISS inc Gland Plate Callout Figure 8 Gland Plate Figure 9 Recessed Connector Panel 1 120 Volts AC Input 2 Network Input 3 Adjustable Cableway NA CUA ADJUSTABLE NETWORK NETWORK CABLEWAY 3 26 2012 4823AC User s Manual 3 DAISY DATA ISS INC Inside Door Callout 1 5 9 7 8 WO W 8 CR ae 10 2 3 11 4 6 12 Figure 11 Door Interior 1 Door Assembly 8 USB Keypad Cable 2 Backlight Inverter 9 0 6 Thermostat for ATX 3 Lamp Voltage Cables power supply 4 Keypad Assembly 10 8 16 Thermostat for all 5 Backlight Power Control heaters Signal Cable 11 Touch Screen Ribbon Cable 6 Touch Screen Controller 12 Keypad Controller Board 7 Touch Screen Power Data Cable 3 26 2012 4823AC User s Manual 4 DAISY DATA ISS inc Inside Enclosure Callout 3 26 2012 DAE ON Figure 12 Enclosure Motherboard Cage 7 PCI Card Retainers se
6. P N P000 000123 1100 001842 CAPACITIVE TOUCH SCREEN CONTROLLER LAMP VOLTAGE LVDS VIDEO D D P N P040 100026 D D P N 1100 001807 P C BOARD 12 MN D D P N P070 000520 HEATERS 120 vac i P N GE PT 000041 iw SERIES VOTERS J D D P N 1100 001825 D D P N 1301 000029 LVO LVDS POWER BESEL I JUSB 5 amp 6 ATX DC POWER Dc Powe use p SB 42 gt lt USB 43 ei USB p SIGNLE d BOARD ATX D D P N IDE1 201 501408 01 m NY m COMPUTER nG IDE2 NETWORK 10 100 BASET CUSTOMER SUPPLIED DD PA Pm NETWORK CAB 1640 001502 01 D D P N 1100 001805 D D P N 1640 001497 I 4 GB DRIVE DD P 1100 001802 D D P N E204 101503 amp E204 100503 ATX POWER A C SURGE CUSTOMER SUPPLIED SUPPLY FILTER 120 VAC INPUT CABLE dinn aae a GS NP napagana iro D D P N P030 000004 Q D D P N P030 000005 SOLID STATE 1640 001518 01 AC RELAY D D P N E110 000025 1100 601600 I D D 1100 001803 15C OPEN ENCLOSURE CABLE ENTRY THROUGH CUSTOMER SPECIFIED GLAND PLATE THERMOSTATS E111 000022 WILL TURN ON THE HEATERS AT 8 C THEN TURN THE HEATERS OFF AT 16 C SET OF HEATERS IN SERIES DRAW 0 524 62 1 WATTS EACH HEATER DRAWS 1 03A 124 1 WATTS TOTAL FOR SET 2 06A 248 2 WATTS THERMOSTAT E111 000024 WILL TURN OFF THE ATX P S AT OC
7. able 15 Transflective LCD Display P070 000520 LCD Backlight Inverter Module 1640 001466 02 15 LCD Door Assembly must specify touch screen option P030 000004 AC Filter 110VAC 20A TVSS Plug P030 000005 AC Filter Base DIN Rail Mount 1024 000013 Keypad Controller must specify optional firmware 1301 000035 CPU Power Reset Membrane Computer Components Part Number Description 1640 001502 01 SBC Card Cage Assembly SBC Card Cage Assemby Part Numbers subject to revision or change without notice 3 26 2012 4823AC User s Manual 12 DAISY DATA displays inc Schematic amp Block Diagram MEMBRANE KEYPAD 14 KEY D D P N 1301 000025 KEYPAD CONTROLLER P C BOARD D D P N 1024 000013 D D P N 1100 001796 D D P N P071 000001 HEATERS D D P N P071 000001 THERMOSTAT 28C CLOSED D D P N I100 001813 1100 001809 12 VDC COOLING FANS 1640 001503 H MODEL 4823AC ENCLOSURE O REVISIONS sm T ow a iN A UPDATED TO CAPAOTIVE TS 2 24 08 BWP MODEL 4823AC DIVISION 2 COMPACT NON INCENDIVE 15 FLAT PANEL PC NOTES 06000 nice mmt n ti mi n i o M re rU E a AA M mm AA TM iom 71 THERMOSTAT Ew FRONT DOOR BC CLOSED 15 CAPACITIVE x a THERMOSTAT vi Aer 16C OPEN 8C CLOSED THERMOSTAT 15 TRANSFLECTIVE OC OPEN LCD DISPLAY 6C CLOSED D D P N I D D
8. ble directly to faulty materi als and or workmanship occur Seller will at its option and without charge to the cus tomer for labor and parts repair or replace the defective product F O B Seller s plant but Seller will not be responsible for freight from Purchaser to Seller s plant In no event shall Seller be liable for any loss inconvenience or damage whether direct incidental consequential or otherwise resulting from abuse misapplication or modifica tion of the product improper or faulty power damage resulting from repairs or altera tions performed by unauthorized persons or conditions resulting from any other equip ment attached to the product Seller assumes no liability for damage occurring in transit due to the product not being returned in its original shipping material This warranty is exclusive and is in lieu of any warranty of merchantability or fit ness for a particular purpose or other warranty of quality whether expressed or implied except of title and against patent infringement Correction of nonconform ities in the manner and for the period of time provided above shall constitute fulfillment of all liabilities of the Seller to the Purchaser with respect to or arising out of the goods whether based on contract negligence strict tort or otherwise LIMITATION OF LIABILITY The Seller shall not under any circumstances be liable for special or consequential damages such as but not limited to damage or loss
9. e pg 7 Flash Drive Assembly for assembly instructions CD Drive Power Connector 8 PCI Expansion Slots 2 Power Supply Assembly 9 Peripheral Component Inter CPU Reset Switch connect PCI USB label Thermostat for fin fans 10 1 O Ports Label under power supply 11 Fin Cooling Fans 4823AC User s Manual 5 DAISY DATA displays inc PCI Card Retainer Assembl AD KO NM 1 Loosen thumb screws on CPU cage 2 Remove 2 6 nuts from studs Qty 4 3 Place card into bracket and slide stud assembly to about 50 from end of card gt J COR d P T al ry j qr P d ig e 5 Place single or double card bracket onto stud assembly and secure with 2 6 nuts 6 Angle clip bracket and attach to PCI 7 Slide clip bracket over flush to card card end Clip will snap tightly onto card and secure with thumb screw Locktite in place to secure MULTIPLE CARD AND CLIP BRACKETS SHOULD BE USED TO BETTER RETAIN THE END OF THE CARD FOR SHOCK AND VIBRATION LOCATION AND NUMBER OF BRACKETS TO BE DECIDED UPON BY CUSTOMER NEEDS 3 26 2012 4823AC User s Manual 6 DAISY DATA displays inc Specifications MATERIAL Enclosure Viewport Design PHYSICAL 15 0 Weight Viewing Window ELECTRICAL Voltage Power Computer amp display only Cast Aluminum Powder Coat Finish Polycarbonate Standard NEMA 4X Non incendive electrical equipment 15 50 Height H4
10. ems must be also positioned to avoid exposure to ex cessive heat Do not mount the unit in close proximity to a steam line heated vat or oven Gland Plates Before modifications can be made Gland Plates must be removed Please note that metal shavings are detrimental to electronic systems Machining Only make enclosure penetrations in designated locations All metal shavings must be collected and removed Wiring Requirements AC power inputs require dedicated circuits or feeds Power from lines or circuits shared by motors drives welders arc furnaces or inductive lighting is not acceptable Conduits for HMI and Purge power should be separated from other conduits to prevent radiated or induced interference Devices that produce spikes surges and brownouts are detrimental to computers and can corrupt data and interfere with purging systems Do not use a transformer or other device to step down a three phase circuit to run a HMI or Purge System Communication wires and signals should be run in separate conduits and routed away from power conduits Providing isolation to prevent emissions from other conduits is essential to data integrity Long runs of parallel signal lines can cause cross talk and corrupt data making communications unreliable or impossible DC power should be provided by a dedicated power source If multiple units must be powered from a single DC supply the power cables must be run directly from the unit to t
11. f the FCC Rules which are de signed to provide reasonable protection against radio interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference Some components may not have been manufactured by Daisy Data Displays Inc If not Daisy has been advised by the manufacturer of the component that the component has been tested and complies with the Class A computing device limits as described above Copyright 2008 Daisy Data Displays Inc All rights reserved No part of this publica tion may be reproduced photocopied stored on a retrieval system or transmitted without express prior written consent Daisy Data Displays Inc 2850 Lewisberry Road York Haven PA 17370 USA Phone 717 932 9999 www 3inc net March 2012 Edition Manual Revision 1 0 3 26 2012 4823AC User s Manual l DAISY DAIA j cisotaus inc Limited Warranty Limited Warranty and Liability Statement To the original purchaser Daisy Data Displays Inc hereinafter referred to collectively as SELLER warrants each of its manufactured products and all components therein contained to be free from defects in materials and or workmanship for a period of 12 months from the date of purchase Should a malfunction or other indication of defect attributa
12. he supply Chaining power from one unit to the next is unacceptable Units can in terfere with each other by developing noise due to the resistance of the wires The fil tering is provided by the source or power supply Additional Wiring It is not permitted to run wiring through the unit that is nonessential to the unit The cabinet is not a junction box Adding Additional Equipment Installing additional equipment in units approved for hazardous classed environments violates the approval of the unit 3 26 2012 4823AC User s Manual iii DAISY DAIA cisotaus INC Table of Contents Table of Contents IDISGIAIMNCT gelu E Limited Warranty and Liability Statement i Power and Signal Wiring Requirement iii Table of Contents EE iv FTODEDOOP OG AIIOUE tuna NAAN NAGTATANONG AN AA AA 1 Enclosure Sides Callout oo ccc ccc I esee e e eese nnn 2 Enclosure Gland BoxCallout nme enne 3 inside Door Callout PA ar ON ie 4 ASIC Enclosure Calloul 5 PCI Card ee ul KT EE 6 SPECIA AA PAA MR PENES IMMINET SENTI T TEOUDIC SMOOUING AA 8 Maintenance and Cleaning EE 10 Replacement Parts lest 12 Schematic amp Block RE Le un BEE 13 Bru Mc ce eee 14 3 26 2012 4823AC User s Manual iv DAISY DAIA ISS inc Front Door Callout
13. n be cleaned with just about any cleaner available but care should be used if using solvents near gaskets and touch screens or viewing win dows Enclosures and external heat sinks should be kept clean and free of the accu mulation of dirt which can cause the buildup of heat and performance degradation 3 26 2012 4823AC User s Manual 10 DAISY DATA aisatays Operation Temperature lt 8 C Heaters Off NE Temperature gt 16 C Temperature gt 6 C ATX Power Supply Off _ ATX Power Supply On Temperature 0 C Temperature gt 28 C Cooling Fans Off mu Cooling Fans On Temperature lt 15 C Figure 14 Thermostat Operation Cold Temperature Delayed Start Up At low temperatures this computer won t turn on until the heaters are allowed to bring the internal temperature up to 6 C This may take up to 1 hour 3 26 2012 4823AC User s Manual 11 DAISY DATA gisoteus Inc Replacement Parts List Model Number 4823AC HVAC Components Part Number Description 070 000433 110VAC Heater Kapton 5 x10 52 9 Ohms 1100 001809 Card Cage Cooler Fan Assembly 1640 001503 Cooling Fan Array Assembly for Fins E906 00068 CPU Cooler Heatsink and Fan 1100 001800 Thermostat OY 2PHSG 20 L 1100 001801 Dual Thermostat 8x amp 8x 2PHSG 100 001813 Thermostat 15Y0 2PHSG 6 L User Interface Components Part Number Description 1301 000025 14 Key Membrane Keypad Legend is customiz
14. of other property or equipment loss of profits or revenues cost of capital cost of pur chased or replacement goods or claims of customers of Purchaser for service interrup tions The remedies of the Purchaser set forth herein are exclusive and the liability of Seller respect to any contract or anything done in connection therewith such as the performance or breach thereof of from the manufacture sale delivery resale installa tion or use of any goods covered by or furnished under this contract whether arising out of contract negligence strict tort or breach of warranty or otherwise shall not except as expressly provided herein exceed the price of the goods upon which such liability is based This warranty gives you specific legal rights and you may also have other rights which vary from state to state Seller makes every effort to provide clear and accurate technical information on the ap plication of its products in the Operator s Manual and assumes no liability for misuse of the information 3 26 2012 4823AC User s Manual i DAISY DAIA j cisotaus inc Power and Signal Requirements Power and Signal Requirements Mounting Location When mounting Human Machine Interfaces HMI and Purge systems must be posi tioned to avoid radiated and induced interference Do not mount the unit in close prox imity to a device that generates strong radiofrequency interference or electromagnetic interference HMI and Purge syst
15. simultaneously Did the computer start Contact factory for No service Yes Y CMOS may have lost BIOS setting data Correct BIOS settings Does the compute start when external power is applied CMOS battery may be NG dead Replace battery Yes Y A brownout from the power source may have caused a glitch in the power system resulting in the corruption of the CMOS data Verify quality of power source Figure 13b Power problem flowchart 3 26 2012 4823AC User s Manual DAISY DAIA ISS inc Maintenance and Cleaning Maintenance and Cleanin While D3 s products are designed to be durable and dependable certain parts need to be maintained and cleaned occasionally This will help to keep units operating at full potential Conductive dust or buildups of liquids can affect capacitive touch screens Touch screens made from glass and polycarbonate can be cleaned with Isopropyl alcohol or a 50 50 mix of Isopropyl and water Apply solution onto a clean lint free cloth first Do not spray the cleaner directly onto the window Ammonia based cleaners are not rec ommended Live steam should not be used in the cleaning of the units Solvents and abrasives can damage anti glare coatings Scratches cannot be buffed out of touch screens Elastomer keyboards and mice should be cleaned using a soft brush with mild soap and water otainless steel enclosures ca
Download Pdf Manuals
Related Search