Infrared Thermometer RT1241 - nu-beca
Contents
1. 0 C 96 8 F and greater than 39 0 C 102 2 F 21 22 SYMBOL INFORMATION Consult instructions for use 0 N Caution consult accompanying documents ec REP Do not use if package is damaged Ec REP Authorized representative in the European Community REFERENCE STANDARDS Device Standard Device Corresponds to the requirements of the standard for infrared thermometers ASTM E1965 98 EN 12470 5 EN 60601 1 2 2007 AC 2010 EN 60601 1 4 1996 EN 60601 1 6 2010 Electromagnetic Compatibility Device fulfills the stipulations of the standard EN 60601 1 2 C Eaz Cli The stipulations of EU Directive 93 42 EEC for Medical Devices Class lla have been fulfilled2. cool and dry place 20 C to 60 C 4 F to 140 F and relative humidity less than 95 gt Avoid direct sunlight gt Avoid dropping the thermometer if it happens and you think the thermometer may be damaged please contact customer services immediately gt Do not touch the lens gt Do not disassemble the thermometer gt Basic safety precautions should always be observed especially when the thermometer is used on or near children and disabled persons gt This thermometer is not intended to substitute for a consultation with your physician gt The forehead scan temperature serves as a reference only It cannot be a judgment on fever RESTRICTIONS OF USE This thermometer is clinically proven to produce accurate tempera ture measurements However please be advised if you have the following situations The accuracy cannot be ensured when the thermometer is not clean Check that the probe is clean before tak ing a measurement INTRODUCTION Thank you for choosing RT 1241 Thermometer Please read this instruction manual first so you can use this thermometer safely and correctly Please keep this instruction manual for future refer ence This innovative medical device uses advanced infrared IR technology to measure temperature instantly and accurately on the forehead surface Intended Use RT 1241 Thermometer is intended for the intermittent measurement and monitoring of human body temperature from forehe
3. Object surface temperature indicator Room temperature indicator Memory mode Temperature unit Error warning DISPLAY MODE Three modes can be selected 1 Body mode This mode is used to measure the forehead temperature It also provides clock 2 Surface mode This mode is used to measure the object surface tempera ture It also provides clock 3 Room mode This mode is used to measure the room temperature It also provides clock SURFACE SURFACE Or SETTING THE THERMOMETER You will need to set time for first time use or after replacing the bat tery Step 1 Press the WP to turn on the thermometer first Press the for 5 seconds to enter the setting mode Step 2 Set the date and time gt Press the Mode or C F button to select the correct month gt Press the to move on the next step b Press the Mode or C F button to select the correct day year hour minute DATE Setting is all completed The thermometer will automatically turn it off 10 NOTE If the meter is idle for 30 seconds during the setting mode it will switch off automatically TI REPLACING THE BATTERY The thermometer comes with two 1 5 V AA alkaline batteries The meter will display to alert you when the meter power is getting low If a and N appear both please follow the steps below to replace new batteries immediately Step 1 Remove the battery cover as the
4. ad measure ment at home The device is intended for use by people of all ages in the home How does it work The thermometer measures the infrared heat generated by the surface of the skin over the vessel and its surrounding tissue The thermometer then converts it into a temperature value NOTE The thermometer does not emit any infrared signal HIGHLIGHTED FEATURES gt Fast and accurate meets the accuracy requirement specified in ASTM E1965 98 and the EC directive 93 42 EEC gt Non contact measurement that does not require probe cover thereby saving cost of replacement gt Automatically power off if left idle for 30 seconds gt Memory function allows you to recall previous results up to 10 previous results gt Easy to read LCD with backlight in a dark environment gt Able to measure temperature of other objects without contact and room temperature PACKAGE CONTENTS RT 1241 Thermometer User s Manual WARRA NT y Two 1 5V AA batteries Warranty Card THERMOMETER PARTS ia DISPLAY SCREEN o DATE mF e o IA PM o ICCIEI Uu pE ne l o6 SURFACE e ROOM dF o C F Button SET Button o Probe 0 Display Screen On Scan Button MODE Button O MEM Button O Battery Cover Q Low battery indicator O Date indicator O Date Time Temperature reading Body temperature indicator
5. arrow direction accordingly Figure 1 Step 2 Remove the old batteries and replace with two 1 5V AA size alkaline batteries Figure 2 Figu Step 3 Close the battery cover If the batteries are inserted correctly you will hear a beep afterwards 1 Although the thermometer works when amp 2 appears we still recommend that you change the batteries to obtain an accurate result 2 Remove the batteries if stored for a long period of time 3 The batteries should be kept away out of child s reach If they are swallowed promptly see a doctor for help 12 ABOUT NORMAL BODY TEMPERATURE amp FEVER Body temperature can vary from one individual person to next It also varies by location on the body and time of day Below shows the statistical normal ranges from different sites Please keep in mind that temperatures measured from different sites even at the same time should not be directly compared Fever indicates that the body temperature is higher than normal This symptom may be caused by infection overdressing or immunization Some people may not experience fever even when they are ill These include but are not limited to infants younger than 3 months old persons with compromised immune systems persons taking antibiotics steroids or antipyretics aspirin ibuprofen acetaminophen or persons with certain chronic illnesses Please consult your physician when you feel ill even if you do not hav
6. d the result Release the button and read the result ROOM is shown together with a temperature value and two short beeps 17 18 RECALLING THE MEMORY Your thermometer stores 10 most recent readings Step 1 Be sure the thermometer is OFF before recalling this memory Step 2 Press the W to turn on the thermometer Step 3 Press the MEM button to enter the memory mode Each time you press the MEM button a result will be displayed in the order of dates latest result shown first to SURFACE gether with M and number from 1 to 10 When the memory is full the oldest result is deleted as the new one added When the last record is displayed press MEM button again to return the first record SURFACE Om Om im Step 4 Exit the memory Press ON SCAN button to return to the measurement mode or keep the meter in idle for 30 seconds in the memory mode it will switch off automatically CARE amp CLEANING gt The probe is not waterproof Please wipe with a clean and dry cot ton swab to clean the probe on the inside b The body of the thermometer is not water resistant Never put the thermometer under a running tap or submerge it into water Use a soft and dry cloth to clean it Do not use abrasive cleaners gt Store the thermometer in a cool and dry location Free from dust and away from direct sunlight 19 TROUBLESHOOTING The table below shows problems you may e
7. e fever Table 1 Body Site Normal Temperature Range 0 6 C 1 F or more above or below 37 C oa 98 6 F 0 3 C to 0 6 C 0 5 F to 1 F higher than oral Rectal ear temperature 0 3 C to 0 6 C 0 5 F to 1 F lower than oral temperature Axillary armpit 1 Body Temperature at WebMD website http firstaid webmd com body temperature retrieved at 2010 Jan 7 SELECT THE TEMPERATURE UNIT This meter provides two measurement units used for indicating the body surface room temperature C or F for your preferred selec tion Step 1 Press the WP to turn on the thermometer first Step 2 Press the C F button to select Press the WP to begin the mea surement or keep the meter in idle for 30 seconds to automatically turn it off 13 14 USING THE DEVICE As a Body Measurement Thermometer Step 1 Remove the front protec tive cap if present Press W to turn on the thermometer Step 2 Press the Mode button for 5 seconds to enter the dis play mode to select Body mode The Body temperature indicator m 4 flashes Step 3 Move the probe close to the forehead Press and hold the WP Make sure the probe is flat and close to the forehead not at an angle Perform a forehead measure ment with a distance within 5 cm Step 4 Read the result Release the button and read the result ff is shown together with a temperature value and two short beeps B As the forehead measu
8. ncounter All error messages below would be shown together with backlight Please follow what to do to resolve problems If the problem still exists please call your local dealer for help What it means What to do Appear when envi Put the thermometer ronmental tempera under operating tem ture is below system perature range of 10 C to operation range 40 C 50 F to 104 F Appear when envi Put the thermometer ronmental tempera under operating tem ture is above system perature range of 10 C to operation range 40 C 50 F to 104 F an is low and Please replace batteries gt appears on LCD as soon as possible Problem with the Please put the thermom thermometer eter under operating temperature range of 10 C to 40 C 50 F to 104 F If the problem is unsolved please contact the customer service line Battery is very low Please replace batteries prior to further use Body mode tem Please follow this manual perature is below to take a reading again 22 C 71 6 F Body mode tem perature is above 44 C 111 2 F SPECIFICATIONS PIERS 150mm L x 48 48mm W x 55 16mm H 128 8 g Mi include 2 x1 5V AA batteries Battery 2 x 1 5 V AA alkaline batteries Displayed temperature range 22 C to 44 C 71 6 F to 111 2 F Display resolution 0 1 C 0 1 F gt 0 2 C 0 4 F for the range of 36 0 C to 39 0 C 96 8 F to A 102 2 F ea gt 0 3 C 0 5 F for less than 36
9. nu RT 1241 Infrared Forehead non contact Thermometer beca IMPORTANT SAFETY INSTRUCTIONS READ THIS BEFORE USING The following basic safety precautions should always be taken 1 Close supervision is necessary when the thermometer is used by on or near children handicapped persons or invalids 2 Use the thermometer only for the intended use described in this manual 3 Do not use the thermometer if it is not working properly or if it has suffered any damage KEEP THESE INSTRUCTIONS Version 1 0 MAR 2012 311 1240100 001 TABLE OF CONTENTS CAUTIONS AND WARNINGS RESTRICTIONS OF USE INTRODUCTION HIGHLIGHTED FEATURES PACKAGE CONTENTS THERMOMETER PARTS DISPLAY SCREEN DISPLAY MODE SETTING THE THERMOMETER REPLACING THE BATTERY ABOUT NORMAL BODY TEMPERATURE amp FEVER USING THE DEVICE As a Body Scan Thermometer As a Surface Scan Thermometer As a Room Scan Thermometer RECALLING THE MEMORY CARE amp CLEANING TROUBLESHOOTING SPECIFICATIONS SYMBOL INFORMATION 05 05 06 07 07 08 08 09 10 11 12 14 14 15 16 18 19 20 21 22 CAUTIONS AND WARNINGS gt As with any thermometer proper technique is crucial to obtaining accurate temperature readings Please read this manual thor oughly and carefully before using gt Always operate the thermometer in an operating temperature range 10 C to 40 C 50 F to 104 F and relative humidity less than 95 gt Always store the thermometer in a
10. rement temperature is likely to be af fected by sweat oil and the surroundings the reading shall be taken as a reference only m f the probe is placed at an angle close to the forehead measurement the reading will be affected by surrounding temperature The thermometer will automatically turn off if left idle for 30 seconds As a Surface Measurement Thermometer Step 1 Remove the protective cap if present Press to turn on the thermometer Step 2 Press the Mode button for 5 seconds to enter the dis play mode to select Body mode The Surface temperature indicator SURFACE flashes SURFACE 15 16 Step 3 Move the probe close to the object surface Press and hold the WP Make sure the probe is flat and close to the object surface not at an angle Perform an object mea surement with a distance within 5 cm Step 4 Read the result Release the button and read the result SURFACE is shown together with a tempera ture value and two short beeps SURFACE As a Room Measurement Thermometer Step 1 Remove the protective cap if present Press On Scan button to turn on the thermom eter O Step 2 Press the Mode button for 5 seconds to enter the dis play mode to select Room mode The Room temperature indicator RooM flashes Step 3 Press and hold the On Scan button The built in sensor inside the thermometer will capture the ambient temperature automatically Step 4 Rea
Download Pdf Manuals
Related Search