DT-DJ4A
Contents
1. 2 Pick up handset in standby mode each time you press K4 to replace a group of ring tones Four groups ring tones cycle ress K4 ress K4 ress K4 Group 1 D gt Group2 are Group3 M gt Group4 A press K4 3 Put down handset to exit the setting 5 4 Ring Volume Setting 1 There are three kinds of ring volume low range mid range and high range to choose for you 2 Pick up handset in standby mode each time you press K3 to replace a kind of ring volume Three kinds of ring volume cycle Low range press K3 gt Mid range press 3 gt High range A press K3 3 Put down handset to exit the setting 6 Specification e Power Supply DC24V e Power Consumption standby 2 1mA working 75 9mA e Wiring 2 wires non polarity e Dimension 187 H X97 W X33 D mm The design and specifications can be changed without notice to the user Right to interpret and copyright of this manual are preserved Mtend n DPP D202 User Manual Read this manual carefully before using the product and keep it well for future use 5 2 2 When Bit 3 of DIP2 set to ON the Bit 1 2 of DIP2 and Bit 1 5 of DIP1 are used to extended address setting so e2. Bit 1 2 of DIP2 are used to master slave address setting JUE Master monitor 123 HEL Slave monitor 1 123 m_ o N om Slave monitor 2 gt o N om Slave monitor 3 Parts and Functions 97 Handset Unlock button Call button Unlock 2nd button Speaker handset curve Key functions 33 Tl oy Side View Pick up to communicate with visitor Connect handset with monitor Unlock button Press to release the door In standby mode pick up handset then press Call button to Call button Unlock activate the inner call 2nd button During calling talking state press Unlock 2nd button to re lease the second door Send out voice from the visitor 2 Terminal Descriptions 4 Operation Instructions 1 Door release function When visitor calls from outdoor station the monitor rings Sw SW Ka pick up handset to talk with the visitor then press the U
3. cem f eg Apap cote So EER ce O io ERR coame Guo Eem ces EDO RBBB cooeros Tel FR coea oO ERI corem fp E ces i l coer O o D coesa fO O S O corea Wo i Ra cees O O E oez AO ag coesa O RO O EU Coens 5 3 Ring Tone Setting 1 There are four groups ring tones to choose for you Group Group Group3 r TS Code 6 Shane Code 17 PHE Code 28 Pianini LERN JWAAG 12345 12345 12345 oN Code 7 ae Code 18 a Code 29 fafa PERT ARAB 12345 12345 12345 oN Code 8 THARA Code 19 TEF Code 30 LERNE ma ASS 12345 12345 12345 on Code 9 Ooi Code 20 es Code 31 PUNE ENUN anoni 12345 12345 12345 on Code 10 a Dane Code 21 ee Code 32 HURU arg meee 12345 12345 12 345 on Code 11 Cea Code 22 Aare Mahal i 12345 12345 5 2 Slave Address Or Extended Address Setting DIP2 to set it When multi Monitors are installed in one apartment these Monitors have to use the same User Code setting and the Master Slave mode should be set on the Monitor e Bit 1 2 of DIP2 are used to slave address or extended address setting e Bit 3 of DIP2 is used to monitor matched setting When Bit 3 set to ON OFF there are different usages 5 2 1 When Bit 3 of DIP2 set to OFF the
4. de f n in E 7 7 Ton p ONES Ei 3 Unit Mounting Fogn Code 1 DURA Code 12 AFUE Code 23 12346 12345 12345 1 Fix 2 screws to the wall at a appropriate height a Code 2 T e Code 13 Annas Code 24 i majani arafaf SSPmin 2 Connect the system correctly 12345 12345 12345 3 Attach the audio phone to the bracket oN Code 3 oN Code 14 CE Code 25 nngag ae baong jj alah 12345 12345 12345 on Code 4 om Code 15 eas Code 26 ajajaj jj aafaa n mal ila a 12345 12345 12345 a Code 5 oN Code 16 ane Code 27 Pongu ii Cong ii ANOAE 12345 12345 12345
5. nlock button to open the door sw sw pa If the system connect 2 locks press Unlock 2nd button to open the second door M s dk 2 Inner call Pick up handset then press Q CALL button to activate the inner e call all monitors connected to the system will ring at the same time Pick up any er i monitor the others will stop ringing immediately note that the user code must be the 9 T same for all monitors to activate the inner call function wou wm 3 Door Bell Call Button Additional door bell call button can be connected to the O Monitor so that the visitors can ring the door bell again in front of the user s apartment b a When the call button is pressed the Monitor will output ring tones K DIP1 am 10 OmaT 5 Setup Instructions SW SW Door bell call button connection port 5 1 User Code Setting DIP1 to set it L1 L2 Bus terminal f f i VSOT nE In the DT system every apartment must have a unique identification called User Code K4 Used to Ring Tone setting The DIP1 switch d t confi the User Code fi h Monit K3 Used to King Volumesetting e switches are used to configure the User Code for eac onitor DIP1 Bit1 6 Used to User Code setting e Bit 1 5 of DIP1 are used to User Code setting The value is from 1 to 32 which DIP2 Bit1 3 Used to Slave Monitor Address or Extended Address setting have 32 different codes for 32 apartments e Bit 6 of DIP1 is used to video match Bit state User Code Bit state User Code Bit state User Co
Download Pdf Manuals
Related Search