EN Dear Customer, Gigaset Communications GmbH is the legal
Contents
1. External call forwarding Call forwarding is set to the exchange The second B channel is not used for external call forwarding The network provider may charge an additional fee 30 Glossary F Firmware Device operating system Comparable with the BIOS of a PC it stores all the basic infor mation necessary for the functioning of a device To correct errors or update the device software a new version of the firmware can be loaded into the device s memory firmware update G GAP Generic Access Profile Standard enabling the combined use of DECT products from different vendors Group call Group of internal devices that have been assigned the same Receive MSN All the devices in the call group react to an incoming call on that MSN When one device takes the call the others return to the idle state GSM Global System for Mobile Communications Originally European standard for mobile networks GSM can now be described as a worldwide standard In the USA and Japan national standards are now more freguently supported than in the past H Handset General term for a cordless telephone that complies with international standards DECT and GAP Headset Combination of microphone and headphone A headset makes handsfree calls more comfortable There are headsets which are connected by a cable to the handset and wireless headsets that can be registered to a base station via Bluetooth Hold Interrupts and re instat2. Country specific requirements have been taken into consideration We Siemens Home and Office Communication Devices GmbH amp Co KG declare that this device meets the essential requirements and other relevant regulations laid down in Directive 1999 5 EC A copy of the 1999 5 EC Declaration of Conformity is available at this Internet address http www siemens com qiqasetdocs C 0682 35 Appendix Guarantee Certificate United Kingdom Without prejudice to any claim the user customer may have in relation to the dealer or retailer the customer shall be granted a manufacturer s Guarantee under the conditions set out below In the case of new devices and their components exhibiting defects resulting from manufacturing and or material faults within 24 months of purchase Siemens shall at its own option and free of charge either replace the device with another device reflecting the current state of the art or repair the said device In respect of parts subject to wear and tear including but not limited to batteries keypads casing this warranty shall be valid for six months from the date of purchase This Guarantee shall be invalid if the device defect is attributable to improper treat ment and or failure to comply with information contained in the user manuals This Guarantee shall not apply to or extend to services performed by the authorised dealer or the customer themselves e g installation configura
3. Index aig ah EYES WS do xe RE a es 239 For your safety For your safety gt Before installing the Gigaset M34 USB PC adapter and software carefully read the following information Notes on the operating instructions on page 4 Safety precautions on page 5 Notes on the operating instructions Online Help During installation detailed descriptions appear on the screen There is also an online help for each component of the Gigaset M34 software Open the appropriate component and then either click on the Help icon in the tool bar or press the F1 key Operating instructions You can also print out all the operating instructions which can be found in pdf format on the CD ROM supplied To read the instructions you will need the Adobe Acrobat Reader program You can install this directly from the Gigaset M34 software Setup Wizard gt Read the instructions carefully before using for the first time Up to date information The Gigaset M34 CD ROM also includes the file readme txt This contains further important information that only became available after the manual had been printed gt Read the additional information contained in the file readme txt carefully gt Also note the product information on the Internet at http www siemens com gigaset For your safety Safety precautions General safety precautions Only give the Gigaset M34 USB to third parties with the installation instructions
4. Operating the answering machine from any external telephone number After entering a PIN messages can be played back and deleted or the answer ing machine settings changed Repeater A repeater increases the range of a handset connected to a base station The device receives the radio signal from the base station and broadcasts it further Ring delay For each internal party you can specify how many rings take place before this party hears the ring This can also be set for each MSN phone number S Send MSN MSN assignment for outgoing calls A particular MSN is assigned to an internal device as the Send MSN via which all the calls are made A device can have only one Send MSN However the same MSN can be used as the Send MSN for several devices Set An outline line is reserved when you pick up the telephone receiver or press the corre sponding key on your handset call key Streaming Streaming refers to the real time transfer of multimedia data via a network connection The data is not stored in the device used to play it but is downloaded at the time of play ing This allows real time transfer for example for the reception of Internet radio Streaming requires a continuous data flow the server on which the files are located must continuously send the data to the client 33 Glossary T Toggling Toggling allows you to switch between two external callers without allowing the wait ing caller to listen in V V
5. you can update the firmware To do this first check which firmware version is currently being used Then either download the most up to date version of the firmware from the Internet or use the firmware on the CD Checking the firmware version gt Open the Gigaset M34 software and select the M34 USB gt Configuration option in the menu tree The version numbers of the installed hardware and software for your Gigaset M34 USB are shown in the working area gt Compare the version numbers shown with the information you have received with your new firmware Note that a firmware update does not eliminate any hardware faults Only update the firmware if your devices are not working properly or if the version number of your new firmware is higher a 24 Configuring the Gigaset M34 software Updating firmware gt Close all running applications except the Gigaset M34 software gt Make sure that your Gigaset M34 USB PC adapter is directly connected to the PC gt Click on the Firmware update option in the menu tree The button to start the firmware update is shown in the working area gt Click on Start firmware update The Gigaset M34 software is closed The Wizard for downloading new firmware program is opened gt Click on Continue An Explorer window is opened gt Open the directory containing the current firmware CD ROM or firmware down loaded from the Internet which mus
6. Appendix Guarantee Certificate Ireland Without prejudice to any claim the user customer may have in relation to the dealer or retailer the customer shall be granted a manufacturer s Guarantee under the conditions set out below In the case of new devices and their components exhibiting defects resulting from manufacturing and or material faults within 24 months of purchase Siemens shall at its own option and free of charge either replace the device with another device reflecting the current state of the art or repair the said device In respect of parts subject to wear and tear including but not limited to batteries keypads casing this warranty shall be valid for six months from the date of purchase This Guarantee shall be invalid if the device defect is attributable to improper care or use and or failure to comply with information contained in the user manuals In par ticular claims under the Guarantee cannot be made if The device is opened this is classed as third party intervention Repairs or other work done by persons not authorised by Siemens Components on the printed circuit board are manipulated The software is manipulated Defects or damage caused by dropping breaking lightning or ingress of mois ture This also applies if defects or damage was caused by mechanical chemical radio interference or thermal factors e g microwave sauna etc Devices fitted with accessories
7. Do not plug in the unit until the software has been successfully I installed and when prompted to by the Setup Wizard The Setup Wizard for the Gigaset M34 software guides you through the installation of all the associated software components The number and kinds of installation steps depend on the features of your base station and the devices and functions you want to use with your base station Normally the following steps are necessary to successfully install the Gigaset M34 software 1 Prepare base station for use see Preparing the base station on page 10 2 Insert Gigaset M34 CD and run the Setup Wizard see Installing the Gigaset M34 software on page 11 3 Reboot the PC 4 Connect the Gigaset M34 USB PC adapter to the PC 5 Install the device drivers for the Gigaset M34 USB PC adapter 6 Setup further components as required After successful installation you can start the Gigaset M34 software and configure it to your own requirements With the Gigaset S450 Y supplied Yahoo and Y Out are assigned to the two display keys if you register the Gigaset M34 USB adapter on this base station System requirements In order to be able to use the full range of functions the following minimum require ments must be met for installation of the Gigaset M34 USB and software Gigaset products Base station and handset gt The table below provides information about which functions you can u
8. GmbH amp Co KG SHC che a sua volta ha proseguito l attivit della Siemens AG Eventuali dichiarazioni della Siemens AG o della SHC nei manuali d istruzione vanno pertanto intese come dichiarazioni della Gigaset Communications GmbH EL Le auguriamo tanta soddisfazione con il vostro Gigaset Geachte klant Gigaset Communications GmbH is de rechtsopvolger van Siemens Home and Office Communication Devices GmbH amp Co KG SHC de onderneming die de Gigaset activiteiten van Siemens AG heeft overgenomen Eventuele uitspraken of mededelingen van Siemens AG of SHC in de gebruiksaan wijzingen dienen daarom als mededelingen van Gigaset HR Communications GmbH te worden gezien Wij wensen u veel plezier met uw Gigaset Estimado cliente la Gigaset Communications GmbH es derechohabiente de la Siemens Home and Office Communication Devices GmbH amp Co KG SHC gue por su parte continu el negocio Gigaset de la Siemens AG Las posibles declaraciones de la Siemens AG o de la SHC en las instrucciones de uso se deben entender por lo tanto como declaraciones de la Giga SL set Communications GmbH Le deseamos gue disfrute con su Gigaset SCaros clientes Gigaset Communicatlons GmbH a sucessora legal da Sie mens Home and Office Communication Devices GmbH amp Co KG SHO gue por sua vez deu continuidade ao sector de neg cios Gigaset da Siemens AG Ouaisguer declara es por parte da Siemens AG ou da SHC encont
9. N 9 user rights llle 9 T Toggling i iet rete 34 Trademarks llle 6 U Up to date information 4 Update firmware 24 User interface working a ea 26 W Waiting melody Music on hold 32 Issued by Siemens Home and Office Communication Devices GmbH 8 Co KG Schlavenhorst 66 D 46395 Bocholt Siemens Home and Office Communication Devices GmbH amp Co KG 2006 All rights reserved Subject to availability Rights of modification reserved www siemens comlgigaset Ref No A31008 M403 R101 4 7619
10. and CD ROM All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by wmm the government or the local authorities This crossed out wheeled bin symbol on the product means the product is covered by the European Directive 2002 96 EC The correct disposal and separate collection of your old appliance will help prevent potential negative consequences for the environment and human health It is a pre condition for reuse and recycling of used electrical and electronic equipment For more detailed information about disposal of your old appliance please contact your city office waste disposal service or the shop where you purchased the prod uct Notall of the functions described in this manual are available in all countries Installation information Inthe Windows 2000 and Windows XP operating systems you must be logged in as a user with administration rights Contact your system administrator for details if necessary Before installing the Gigaset M34 software read the information under System requirements on page 7 to avoid loss of data During installation you are prompted to connect the Gigaset M34 USB to a free USB port on your PC This starts the Windows operating system s automatic hard ware recognition routine and installs the device drivers Safety precautions for the Gigaset M34 USB PC adapter 4 The operation of med
11. ee ee eis 13 Possible problems during installation 0 0 cece eee eee eens 14 Checking successful installation 2 2 0 0 cece cece e 15 Audio settings zero o Pads IM ee end bb E EE 15 Registering a base station 2 0 0 cece tnt ee ee ee ee eis 16 Status displays for the Gigaset M34 USB 0 0 eee ee 17 Operating information 18 Operation with multiple devices 0 0200 ee 19 Configuring the Gigaset M34 software 20 Checking the connection status use eeeeee ee teen eee 20 Configuring the Gigaset M34 software 020000 eee 21 Registering a base station 0002 e 21 Connecting the base station lisse 21 Changing device niames ss sorelle aoe shat Dae eee SIX rn 22 Calling the Gigaset M34 USB ee ee nee ie eis 22 Deregistering a base station 202000 e 23 Configuring power management 00000 eens 24 Firmiware pdate rat RA AA 24 Operating the Gigaset M34 software 26 Changing and saving settings 020002000 ee ee ee teen nee 27 Opening Help irish aos De bie ar Use r ia eee RES 27 Closing the program 2422 5 oz oa Re ERR UE whee eh ed o 27 Contents Glossary aaa bs AA qutt tob esr 20 Appendix si A E OS cet s OD Service Customer Care oz cete e reet edd oie e oes 35 Guarantee Certificate United Kingdom 02002 ee 36 Guarantee Certificate Ireland lcs 37
12. standard device settings for recording and playback have been changed see also section Audio settings on page 15 Click on OK to complete the installation If you want to use your Gigaset M34 USB PC adapter for Internet telephony VoIP you must install Yahoo Messenger with Voice on your PC The software is available on the Internet at http messenger yahoo com Reboot your PC after installation O e Possible problems during installation On rare occasions it can happen that a program called up by the Gigaset M34 software Setup Wizard does not respond gt Close the Setup Wizard and the program that is not responding and try again If the USB driver cannot be found even though it has been set properly gt Disconnect the Gigaset M34 USB PC adapter from your PC gt Reboot your PC gt Reconnect the Gigaset M34 USB to your PC gt Restart the Setup Wizard In some older PC systems chipsets are fitted which no longer correspond to the valid USB standard This can lead to problems with the USB connec tion a Manufacturers of these hardware components normally supply a driver update Please contact the manufacturer of your PC 14 Installing the software and device drivers Checking successful installation After rebooting the PC the following things indicate that the Gigaset M34 USB and soft ware have been successfully installed The Start menu contains three n
13. 20 0 02 31 Internal ringer 200005 32 IS DIN iasg ee hein dee e a and a 32 K Keypad eA oe ER 32 M MSN i re A Miia KI 32 Music on hold seen 32 N Notes on the operating instructions 4 NTBA ens eR eere 32 O Online help 4 Operating information 18 Operating instructions 4 oOnlinehelp ievveeeeeena 4 up to date information 4 Operating software changing and saving settings 27 Operating the Gigaset M34 software 26 Operation with multiple devices 19 P PDA za RA ER VRE SASS BOTS 32 PIN e AAA E e nee 32 Prepare for use 10 40 R Readme file 4 27 Receive MSN 0 33 Register base station 16 21 Rejects detur ha a nA a 33 Rej ctall eS 33 Remote check 33 Repeater csc sce wade dee ede ees 33 Ring delay 2 20 33 S Safety precautions 5 general rein ee RNA 5 installation 5 Send MSN 0 33 Service Customer Care 35 SOV Res kee pare hice ad ae Wo es 33 Settings changing ee ee ee nee ie 27 SAVING Sie eng ga o 27 Start MENU be chutes eee at heed dss 15 Start Setup Wizard 11 Status displays for the Gigaset M34 USB 17 Streaming 0c e eee 33 System reguirements 7 Gigaset products 7 operating system 9 Dust Ath tAE E aUe on
14. Gigaset EN DE FR NL ES PT Dear Customer DA Gigaset Communications GmbH is the legal successor to Siemens Home and Office Communication Devices GmbH amp Co KG SHC which in turn continued the Gigaset business of Siemens AG Any statements made by Siemens AG or SHC that are found in the user guides should therefore be understood as statements of Gigaset Communications GmbH We hope you enjoy your Gigaset FI Sehr geehrte Kundin sehr geehrter Kunde die Gigaset Communications GmbH ist Rechtsnachfolgerin der Siemens Home and Office Communication Devices GmbH amp Co KG SHC die ihrerseits das Gigaset Gesch ft der Siemens AG fortf hrte Etwaige Erkl rungen der Siemens AG oder der SHC in den Bedienungsanleitungen sind daher als Erkl rungen der Gigaset Communications GmbH zu verstehen Wir w nschen Ihnen viel Freude mit Ihrem Gigaset SV Ch re Cliente Cher Client la soci t Gigaset Communications GmbH succ de en droit Siemens Home and Office Communication Devices GmbH amp Co KG SHC qui poursuivait elle m me les activit s Giga set de Siemens AG Donc les ventuelles explications de Sie mens AG ou de SHC figurant dans les modes d emploi doivent tre comprises comme des explications de Gigaset Communications GmbH Nous vous souhaitons beaucoup d agr ment avec votre NO Gigaset Gentile cliente la Gigaset Communications GmbH successore della Sie mens Home and Office Communication Devices
15. USB make a free internal call from the handset to the Gigaset M34 USB gt Press the INT key on your handset gt Choose the Gigaset M34 USB as the internal party The internal name under which it is registered on the base station can be seen in the Gigaset M34 software under M34 USB gt Configuration gt Name gt Press the Talk or Handsfree key on the handset to make the internal connection Note that your handset will be blocked to other calls for the duration of e the internal connection 22 Configuring the Gigaset M34 software When the connection is no longer reguired gt Break the connection by pressing the End call key on your handset Deregistering a base station For operation with the Gigaset M34 USB a maximum of 6 base stations can be regis tered If all spaces on the list are occupied you must first deregister a base station before you can register another base station A base station can only be deregistered if the Gigaset M34 USB is con nected to it If there is no connection to this base station or the signal strength of the connection is too low the base station is only deregistered in the Gigaset M34 software In this case your PC must also be deregistered as an internal device in the base station menu om gt Open the Gigaset M34 software and select the M34 USB gt Configuration option in the menu tree The working area shows a list of the base stati
16. ase station 23 register base station 16 21 update firmware 24 Configure power management 24 Configuring the Gigaset M34 software 20 21 Connect base station 21 Control Panel software 2 eee ee eee eee 15 Customer Care 222 35 CW Call Waiting 30 D DECT siar air Siete eae nere RI ce 30 Deregister base station 23 Device drivers 000 eee 7 Device Manager 15 Diallep i ere a 30 Dial up connections 30 Dial up network 30 E Enquiry call 0005 30 Exchange 0 esee 30 F Firmware c Ra i 31 For your safety 4 G GAP oreo sree aa a a ah RC Baines ese 31 Gigaset M34 software calling up Help 27 dori E 27 Group Call ecl et 31 GSM es rere ha 31 Guarantee Certificate 36 H Handset i K 31 Headset vino dee RES 31 HONG seit RR redes e RO Tar 31 39 Index I Install software and device drivers 7 Installation llle 7 base station 10 check installation success 15 device drivers 0 0 eu 7 possible errorS 14 seguence eee 7 software ostra e Zda RN sia is 7 start Setup Wizard 11 update firmware 24 Installing the Gigaset M34 software 11 Installing the software 12 Internal calls 2 2
17. aying a computer game you must change the settings of the device driver gt Click on Start gt Settings gt Control Panel gt Sounds and Audio Devices Windows 2000 or Sounds and Multimedia Windows XP Audio tab gt For sound playback and recording select the default sound card driver of your PC as the default device instead of the entry USB audio device gt Click on OK to accept the setting Using PC loudspeaker headset with your handset In most Windows applications you can also give the audio device driver specific settings irrespective of the settings in the Control Panel This allows you to specify where sound 15 Installing the software and device drivers is recorded and played back PC or handset for specific applications For example if you have set your PC s default soundcard driver you can make a phone call with your handset over the Internet while listening to music through your PC s loud speakers at the same time Please note For Internet telephony with Yahoo Messenger with Voice the device driver USB audio device is automatically set temporarily as soon as you telephone with the handset Registering a base station You can register your Gigaset M34 USB on up to 6 base stations To do this you enter the base stations available at the relevant location of the PC in the Gigaset M34 soft ware The registered base stations are saved in the software and you can then connect to one of the registere
18. component This is where you configure the components and enter your data As well as the Help for the Gigaset M34 software the menu bar and the toolbar contain all commands available for the relevant components 26 Operating the Gigaset M34 software Changing and saving settings Settings that you change in the Gigaset M34 software become effective immediately when you exit the relevant option box Opening Help The Gigaset M34 software provides you with various forms of help During installation detailed descriptions appear on the screen There is also an online help for each component of the Gigaset M34 software Open the appropriate component and then either click on the Help icon in the tool bar or press the F1 key You can also print out all the operating instructions which can be found in pdf for mat on the CD ROM supplied To read the instructions you will need the Adobe Acrobat Reader program This can be installed directly from the Setup Wizard for the Gigaset M34 software The Gigaset M34 CD ROM also includes the file readme txt This contains additional important information that only became available after the manual was completed Closing the program gt Select File gt Exit in the menu bar The Gigaset M34 software is closed and all entries are saved Manual saving is not necessary Glossary Glossary A Access code Can be set in the base station as the access code for all o
19. d base stations as required Requirements There must be a free space in the list under Base stations There must be another free registration location for internal participants on the base station The base station must be in registration mode before commencing the registration procedure The base station PIN must be entered during registration For further information refer to the operating instructions for the rele vant base station O gt Open the Gigaset M34 software via Start gt Programs gt Gigaset DECT gt Gigaset M34 Software gt In the menu tree select M34 USB gt Configuration gt Under Base stations click on one of the free base options The Register button is activated gt Set the base station to registration mode Press and hold the registration key for a few seconds Some base stations signal registration mode with an acoustic signal or a flashing LED Refer to the operating instructions for your base station for more details gt Click on Register to begin registration This opens the Register dialog gt Enter the PIN for the base station factory default 0000 and confirm your entry with OK gt Wait until registration has been completed The Register dialog is closed Once the connection between your base station and the M34 USB has been estab lished you will see the base station data on your PC The Name field contains the name un
20. der which the Gigaset M34 USB has been registered on the base station 16 Installing the software and device drivers You will need this name to establish the connection between the handset and the M34 USB Status displays for the Gigaset M34 USB LED is constantly illuminated Base station found Gigaset M34 USB is ready for use LED flashes slowly Gigaset M34 USB is looking for the base station or no base station has been registered LED flashes quickly Data connection active between Gigaset M34 USB and base station LED flickers Gigaset M34 USB is in firmware update mode EE EE ME END ME WE ME IE Operating information Operating information Your Gigaset M34 USB PC Adapter opens up a wide range of possibilities when used in conjunction with your Gigaset base station and the Gigaset M34 software The Gigaset M34 USB is a PC adapter which allows wireless communication between your Gigaset base station and your PC For example you can transfer your PC directories to the handset make calls over the Internet or operate the handset remotely from the PC The functions available depend on your Gigaset base station the handset you are using and the software components installed For details of which base stations can use a par ticular software component refer to the description of the relevant component You can use the Gigaset M34 software to configure the connection between your base station a
21. ephone exchange or the base station Music can be played while the caller is on hold N NTBA Network Terminator Basic Access Network terminator device The public ISDN network is terminated with an NTBA ISDN end devices and PABXs are connected to the NTBA P PDA Personal Digital Assistant Also known as hand held PC Mobile computer in wallet format offering not only organ iser functions but also communication via telephone email Bluetooth etc PIN Personal Identification Number Protects against unauthorised use e g system PIN answering machine PIN headset PIN When accessing a protected area e g device configuration when PIN protection is activated a particular combination of numbers or characters has to be entered 32 Glossary R Receive MSN MSN assignment for incoming calls A call for a particular MSN is sent to all internal devices that have been assigned this MSN as their Receive MSN Reject An incoming call is rejected on an internal device If several devices have the same Receive MSN these will continue to ring until the call has been rejected on all the devices in that call group or it has been taken on one of the devices Reject all Extended call rejection When an incoming call is rejected on any device that call is rejected for all devices in the same call group The caller continues to hear the ringing tone but the devices themselves no longer ring Remote check Also remote access
22. erating instructions for your phone line or PABX O e 10 Installing the software and device drivers Installing the Gigaset M34 software When the software has been installed successfully please do not I plug in the device until the Setup Wizard prompts you to do so gt Read the information in System requirements on page 7 and the readme txt file before starting to install the Gigaset M34 software You will find the readme txt file in the readme directory on the product CD It contains current additional informa tion on installation and software gt Close all the programs running on your PC This also includes those programs e g antivirus software whose activity is only indicated by an icon in the status area of the taskbar next to the clock Starting the Setup Wizard gt Insert the Gigaset M34 CD into your PC s CD ROM drive The Setup Wizard for the Gigaset M34 software is started automatically If the Setup Wizard for the Gigaset M34 software does not start automat ically gt Open Windows Explorer gt Select the CD ROM drive gt Double click start exe O The Setup Wizard guides you through the installation gt Select the language in which you want to install the Gigaset M34 software gt Click on Continue The main menu for the installation software is opened 11 Installing the software and device drivers gt Click on one o
23. es an existing connection In particular it permits enguiry calls and toggling between calls Internal call forwarding Call forwarding is set to the base station The second B channel is used for forwarding the call Both B channels are busy during an internally redirected call If a B channel is already busy before the call is redirected internal call forwarding cannot be activated Internal calls Free calls between devices connected to the base station 31 Glossary Internal ringer Special ring tone on PABXs to distinguish between internal and external calls ISDN Integrated Services Digital Network All data including voice is sent digitally with ISDN The network operator normally pro vides at least two B channels per ISDN line An active connection can be set up for each B channel allowing e g simultaneous surfing and calling K Keypad Keypad supports special function keys such as the star and hash 4 This allows you to send control signals during a call so that you can use particular features of your ISDN network M MSN Multiple Subscriber Number Multiple subscriber number Multiple subscriber numbers are your own telephone num bers assigned to you by your network provider when your ISDN line was set up Up to ten MSNs can be assigned to one ISDN connection Music on hold Playing of music or a service announcement With the enquiry call toggling and redirect features the call is held in the tel
24. ew links Start Programs Gigaset DECT Gigaset M34 Software Start gt Programs gt Gigaset DECT gt Gigaset M34 USB Firmware update The following items have been added to the Device Manager in your Windows operating system Start gt Settings gt Control Panel gt System gt Hardware gt Device Manager Under DECT Devices Cordless Internet Access Under Network Adapters Under Audio Video and Game Controllers USB audio device Under USB Controller Cordless Device Configuration Cordless Device Line Access Cordless Device Update Cordless PC Control The Software area in the Control Panel of the Windows operating system shows the names of the installed software components Gigaset M34 Software Gigaset M34 USB Certain entries are only displayed when a base station is connected O e The drivers may have different names depending on the Windows operating system you are using and the voice packets installed Audio settings Due to Microsoft Software Regulations the audio device driver USB audio device has been installed onto your PC as your default device for recording and playback This is also necessary because it allows you to listen to music through your handset with Windows Media Player or make phone calls via the Internet For example if you wish to record or playback sound on your PC e g through your PC s loudspeaker microphone or connected headphones while pl
25. f the following options if you want to read additional information about installing the software Readme files Up to date additional information about installation and the software Operating instructions The operating instructions for the Gigaset M34 USB and software The operating instructions are in PDF format and can be viewed on your PC or printed out To do this you will need the free Acrobat Reader soft ware This can be found in the Service amp Support area of the CD ROM supplied As well as the operating instructions in PDF format the software also provides an online help which you can call up directly from within the program Service amp Support This area contains Internet links to the web pages for Siemens Home and Office Communication Devices GmbH amp Co KG You can also install the Acrobat Reader program to view the operating instructions Uninstall all components This is used to remove the entire Gigaset M34 soft ware including all components from your PC Or gt Click on Install software to start the installation of the Gigaset M34 software You will find a detailed description of the installation steps in the next section Installing the software Installation involves various steps in which you can select a number of options After each step confirm your selection with Next to continue the installation procedure Use Back to return to your previous selection You will find detailed information on in
26. figu ration to be able to establish a connection from those locations at any time However you should note that a simultaneous connection to multiple base stations is not possi ble Use the M34 USB option in the menu tree to open up the configuration of the Gigaset M34 software The following configuration dialogs are available Menu tree Brief description M34 USB Status Display connected base station and quality of connec tion Configuration Register and configure Gigaset M34 USB and enter avail able base stations Firmware update Update device software for your Gigaset M34 USB Checking the connection status gt Open the Gigaset M34 software and select the M34 USB gt Status option in the menu tree The working area displays up to date information about the connection to the base station Connected base If a connection already exists the name of the base station to which your PC is con nected via the Gigaset M34 USB is shown Field strength The signal strength of the wireless connection is indicated in the form of a bar Connection status The wireless connection can have the following operating statuses lnitialise Connecting searching for an available base station No connection No connection to base station or connection broken Active Your PC is connected to the base station displayed 20 Configuring the Gigaset M34 software Configuring the Gigaset M34 software You ca
27. g system Windows 2000 Service pack 4 or Windows XP Have the installation CD for your Windows operating system to hand During the installation of the Gigaset M34 software the Setup Wizard checks the configuration of your operating system You may be prompted to install certain additional Windows components User rights It is necessary that you are logged in as a user with administration rights Contact your system administrator for details if necessary Pack contents 0 0 09 1 Gigaset 450 Y 1 Gigaset M34 USB PC adapter 1 USB extension cable 1 CD ROM containing software and comprehensive operating instructions 1 set of installation instructions Installing the software and device drivers Preparing the base station gt Read the operating instructions for your base station gt Connect your base station Connect your base station to your phone line or PABX using the telephone cable Connect the base station to the power supply using the mains adapter Your base station is now ready for use Now that your base station is ready for use you can make external calls and also take incoming calls It is not necessary to install the Gigaset M34 software to do this gt You can check that your base station is working properly by dialling an external telephone number gt f you cannot make the call check your phone line or the settings for your PABX You will find a detailed description in the op
28. ge in the burden of proof to the detri ment of the customer To invoke this Guarantee please contact the Siemens helpdesk on 1850 777 277 This number is also to be found in the accompanying user guide 38 Index A Access Code a a SR TH Ar 28 AGN a a AA ih 28 Answering machine AM 28 Appendix s si LOVE pi eek 35 Audio settings ee ee ee 15 Authorisation see ee ea 28 B Base station prepare for use 10 preparing for installation 10 B chanrieliz 4o rA ne 28 Blockdialling ee ee ee 28 Bluetooth see ee ee 28 C Call forwarding external V EE 30 internal os SS ME Ac Ae leis tied 31 Call forwarding CF 29 Call Gigaset M34 USB 22 Callwaiting eeeeeeeeeeeeea 29 Callback when the call is not answered 0 29 Callback when the number is busy 29 Calling up Help 27 Calls list x2 RE RE eA 29 GADPILL o Led https e c EE 29 CF Call Forwarding 29 Change device names 22 Check connection status 20 CUP stereo e ca ee es ee 29 idi as ar re ee 29 ClOSe zi Det DEDERE 27 Close software 27 Comfort handset 30 Configuration 20 21 call Gigaset M34 USB 22 change device names 22 check connection status 20 configure power management 24 connect base station 21 Index deregister b
29. ical appliances may be affected 4 Do not operate the Gigaset M34 USB in bathrooms or shower areas The Gigaset M34 USB PC adapter is not splash proof Avoid the immediate proximity of heat sources such as radiators and do not expose the Gigaset M34 USB to direct sunlight Only use the USB extension cable supplied 4 Do not connect or disconnect the Gigaset M34 during a storm This brings a risk of electric shock If the Gigaset M34 USB comes into contact with liquid do not use it Allow the liquid to drain out of the device and then pat all parts of the device dry Store the Gigaset M34 USB in a warm dry place for at least 72 hours In many cases you will then be able to use it again For your safety Wireless transmission between the base station and portable part is based on the DECT 6 0 Standard The Gigaset M34 USB PC adapter meets the appropriate European specifications Should there nevertheless be any picture and sound interference with satellite receivers please consult your retailer to have your satellite receiver eguipment tested for poor shielding Trademarks Windows 2000 Windows XP Outlook Windows Media Player and Windows Explorer are registered trademarks of the Microsoft Corporation Acrobat is a registered trademark of Adobe Systems Incorporated Yahoo is a registered trade mark of Yahoo Inc Installing the software and device drivers Installing the software and device drivers
30. ions GmbH este succesorul legal al companiei Siemens Home and Office Communication Devices GmbH 8 Co KG SHC care la r ndul s u a continuat activitatea companiei Gigaset a Siemens AG Orice afirmatii efectuate de Siemens AG sau SHC si incluse n ghidurile de utilizare vor fi prin urmare considerate a apartine Gigaset Communications GmbH Sper m ca produsele Gigaset s fie la in ltimea dorintelor dvs Po tovani potro a u Gigaset Communications GmbH je pravni naslednik kompanije Siemens Home and Office Communication Devices GmbH 8 Co KG SHC kroz koju je nastavljeno poslovanje kompanije Gigaset kao dela Siemens AG Stoga sve izjave od strane Siemens AG ili SHC koje se mogu na i u korisni kim uputstvima treba tuma iti kao izjave kompanije Gigaset Communications GmbH Nadamo se da ete u ivati u kori enju svog Gigaset ure aja Ysaxaemn notpebutenn Gigaset Communications GmbH e npagBgorpweMHWKbT Ha Siemens Home and Office Communication Devices GmbH amp Co KG SHC koaTo Ha CBO pen npogbnxn 643Heca Ha noapaaneneuuero Siemens AG lo tasn npwuwHa BCAKAKBU UZNOXEHNA HanpaBeHn or Siemens AG nnn SHC konTo ce HAMUPAT B PBKOBOJCTBATA 3a norpe6urens cnenga na ce PAZOUNPAT KATO NZNOMEHNA Ha Gigaset Communications GmbH HagnsBawe ce na nonsBate c ynoBoncrBue Baluua Gigaset Tisztelt V s rl A Siemens Home and Communication Devices GmbH amp Co KG SHC t rv nyes jogut dja a Gigaset Communicati
31. juje dejavnost znamke Gigaset podjetja Siemens AG Vse izjave podjetja Siemens AG ali SHC v priro nikih za uporabnike torej veljajo kot izjave podjetja Gigaset Communications GmbH Zelimo vam veliko u itkov ob uporabi naprave Gigaset Gigaset Communications GmbH 2008 All rights reserved Subject to availability Rights of modifications reserved www gigaset com Gigaset CS SK RO SR BG HU V en z kazn ci PL spole nost Gigaset Communications GmbH je pr vn m n stupcem spole nosti Siemens Home and Office Communication Devices GmbH 8 Co KG SHC kter d le prejala segment produkt Gigaset spole nosti Siemens AG Jak koli prohl en spole nosti Siemens AG nebo SHC kter naleznete v u ivatelsk ch pr ru k ch je tfeba pova ovat za prohl en spole nosti Gigaset Communications GmbH Douf me e jste s produkty Gigaset spokojeni V en z kazn k Spolo nos Gigaset Communications GmbH je pr vnym TR n stupcom spolo nosti Siemens Home and Office Communication Devices GmbH 8 Co KG SHC ktor zasa pokra ovala v innosti div zie Gigaset spolo nosti Siemens AG Z tohto d vodu je potrebn v etky vyhl senia spolo nosti Siemens AG alebo SHC ktor sa nach dzaj v pou vate sk ch pr ru k ch ch pa ako vyhl senia spolo nosti Gigaset Communications GmbH Ver me e budete so zariaden m Gigaset spokojn Stimate client RU Gigaset Communicat
32. mbH Vi nskar dig mycket n je med din Gigaset Kj re kunde Gigaset Communications GmbH er rettslig etterf lger etter iemens Home and Office Communication Devices GmbH amp o KG SHC som i sin tur videref rte Gigaset geskjeften i iemens AG Eventuelle meddelelser fra Siemens AG eller HC i bruksanvisningene er derfor forst som meddelelser fra Gigaset Communications GmbH Vi h per du f r stor glede av din Gigaset enhet un un ra ua Ayannt nel tiooa ayannt ng n n Gigaset Communications GmbH siva n vojukr L OXOG TIS Siemens Home and Office Communication Devices GmbH amp Co KG SHO n onoia yet ava er tnv ELTOPIK Opaotnpi tnta Gigaset tng Siemens AG OL n s tnc Siemens AG mc SHC otic odnyies xprjong axoteAov gnop voc SNAWOEIs tng Gigaset Communications GmbH Zac vy paote koAr Siack daon LIE TI ovokev oac Gigaset Po tovani korisnici Gigaset Communications GmbH pravni je sljednik tvrtke Siemens Home and Office Communication Devices GmbH amp Co KG SHC koji je nastavio Gigaset poslovanje tvrtke Siemens AG Zato sve izjave tvrtke Siemens AG ili SHC koje se nalaze u uputama za upotrebu treba tumaciti kao izjave tvrtke Gigaset Communications GmbH Nadamo se da sa zadovoljstvom koristite svoj Gigaset uredaj Spo tovani kupec Podjetje Gigaset Communications GmbH je pravni naslednik podjetja Siemens Home and Office Communication Devices GmbH 8 Co KG SHC ki nadal
33. n make various settings in the Gigaset M34 software change the names of your devices register or deregister base stations connect devices to one another control the power management feature and update the firmware if necessary Registering a base station gt Open the Gigaset M34 software and select the M34 USB gt Configuration option in the menu tree gt Under Base stations click on one of the free base options The Register button is activated gt Set the base station to registration mode Press and hold the registration key for a few seconds Some base stations signal registration mode with an acoustic signal or a flashing LED Refer to the operating instructions for your base station for more details gt Click on Register to begin registration This opens the Register dialog gt Enter the PIN for the base station factory default 0000 and confirm your entry with OK gt Wait until registration has been completed The Register dialog is closed gt For further information refer to Registering a base station on page 16 Connecting the base station When you register a base station it is connected immediately If several base stations are registered you can choose which one to connect to The base stations that are not connected do not need to be deregistered This allows you to switch between different base stations without having to set them to registration mode again gt O
34. nd your PC The software does not have to be started to use the basic functions of your Gigaset M34 USB PC adapter you only need the software for special functions such as transferring directories 18 Operating information Operation with multiple devices gt Refer to the table below for details of which devices you can connect to one another Base stations Internet access IP Internet telephony and PC control Maximum number of handsets C340 345 6 C350 355 6 E450 455 6 54401445 6 5450 455 z F 6 450 Y z 6 645 R 6 SL440 z 6 SL550 555 F 6 CX340 345isdn n 14455 CX100 150isdn 6 SX100 150isdn 6 SX203 253isdn amp 8 SX205 255isdn a 8 SX303 353isdn 8 SX440 445isdn 14455 SX450 455isdn 14455 SLX740isdn s 8 4170175isdn x 8 3070 75isdn 8 For these base stations you must carry out a firmware update to Gigaset SX205 255 during the installation One Gigaset M34 USB PC adapter and a maximum of 4 handsets can be registered on these base stations 19 Configuring the Gigaset M34 software Configuring the Gigaset M34 software With the Gigaset M34 USB you can set up your PC for operation on up to 6 base stations Particularly when the location of the PC or laptop changes often this provides the advantage that you only need to enter the available base stations once in the con
35. not authorised by Siemens This Guarantee shall not apply to or extend to services performed by the authorised dealer or the customer themselves e g installation configuration software down loads User manuals and any software supplied on a separate data medium shall be excluded from the Guarantee The purchase receipt together with the date of purchase shall be required as evi dence for invoking the Guarantee Claims under the Guarantee must be submitted within two months of the Guarantee default becoming evident Ownership of devices or components replaced by and returned to Siemens shall vest in Siemens This Guarantee shall apply to new devices purchased in the European Union For Products sold in the Republic of Ireland the Guarantee is issued by Siemens Home and Office Communication Devices GmbH amp Co KG Schlavenhorst 66 D 46395 Bocholt Germany Any other claims resulting out of or in connection with the device shall be excluded from this Guarantee Nothing in this Guarantee shall attempt to limit or exclude a Customers Statutory Rights nor the manufacturer s liability for death or personal injury resulting from its negligence The duration of the Guarantee shall not be extended by services rendered under the terms of the Guarantee Insofar as no Guarantee default exists Siemens reserves the right to charge the customer for replacement or repair 37 Appendix The above provisions does not imply a chan
36. o KG SHC koropas B CBOIO OYepedb npuHsna noapasneneuue Gigaset B cBoe ynpaBneHue or KoMnaHun Siemens AG losTOMY rio6bie 3agnBneHMus CHENAHHBIE OT AHMEHU KOMNAHYUY Siemens AG nnn SHC u BCTPEHAHOLINECA B PYKOBOACTBAX NONB3ZOBATENA AONXKHBI BOCNPUHUMaTbCA Kak ZAABNEHNA KOMIIaHWW Gigaset Communications GmbH Mb Hageemca uro nponykrei Gigaset YOOBNETBOPANOT BaLIIUM TPEOGOBAHNAM Gigaset Communications GmbH 2008 All rights reserved Subject to availability Rights of modifications reserved www gigaset com SIEMENS YAHOO SIEMENS Gigaset M34 Usp B Gigaset M34 USB User Manual Gigaset Contents Contents FOr your safety zaliala AT ok bin i A Notes on the operating instructions ueveeeeeee ee e 4 Safety precautions ss see 020 e a EEEE ER IRURE dae APA AEN ERIS 5 Trademarks eise ees Cum e cec e ee M e Rh cR e ee UR ec sea a 6 Installing the software and device drivers 7 System requiremerits peos gus ga eUnEERRDPUBGPUUULDIS IS bia TIENDE dud Se 7 Gigaset Products me htec enit ves A a 7 Minimum PC requirements 2 0 0020 9 Pack contents coectetuer kA NA 9 Preparing the base station 10 Installing the Gigaset M34 software 020 nee ee ee ee ee nea 11 Starting the Setup Wizard is ern erns a NE et Beg wade La 11 Installing the software 02 02020020 ee ee see ee ee ee ee ee ee se eas 12 Installing the device drivers ee nee ee ee ee ee ee ee se ee se
37. o reboot the PC Installing the device drivers After restarting installation is continued automatically You are prompted to connect the Gigaset M34 USB PC adapter to the PC and the driver software is then installed Later you should register the Gigaset M34 USB PC adapter on your base station and you can then use the full range of functions of the software gt Connect the Gigaset M34 USB to a free USB port on your PC ee 9 U 3 I E gt When you connect the Gigaset M34 USB hardware recognition is started This fea ture monitors the installation of new device drivers Depending on the previous con figuration of your PC it may be necessary to install several drivers for you Gigaset M34 USB PC adapter Hardware recognition is started automatically for each driver installation Follow the hardware recognition instructions On Windows XP confirm the preset options with Continue and then click on Finish 13 Installing the software and device drivers If you cancel hardware recognition the driver software cannot be correctly installed gt Wait until the hardware recognition procedure has completed installation of the device drivers and you see a message to that effect Once this message is displayed click on Continue in the Setup Wizard gt Click on Finish in the Setup Wizard gt Reboot your PC if you are prompted to do so gt A message will be displayed informing you that the
38. olP Voice over Internet Protocol Telephone calls are no longer placed and transmitted over the telephone network but over the Internet or other IP networks 34 Appendix Appendix Service Customer Care We offer you fast support tailored to your specific needs Our Online Support on the Internet can be contacted any time from anywhere www siemens com gigasetcustomercare It will give you 24 7 support for all our products It also provides interactive trouble shooting a list of FAQs and answers plus operating instructions and current soft ware updates for you to download 4 Personal advice on our range of products is available on our Premium Hotline United Kingdom 0 90 69 50 04 30 You can talk to qualified Siemens technicians who will guide you expertly through product information and installation 4 For fast and dependable assistance with any repairs or guarantee warranty claims contact our Service Centres in Ireland 18 50 77 7277 United Kingdom 0845 367 0812 Please have your proof of purchase ready when calling Replacement or repair services are not offered in countries where our product is not sold by authorised dealers Please address any questions about the DSL or cable connection to your network pro vider Authorisation This device is intended for use within the European Economic Area and Switzerland If used in other countries it must first be approved nationally in the country in question
39. ons GmbH amely a Siemens AG Gigaset zlet g nak ut dja Ebb l k vetkez en a Siemens AG vagy az SHC felhaszn l i k zik nyveiben tal lhat b rmely kijelent st a Gigaset Communications GmbH kijelent s nek kell tekinteni Rem lj k megel ged ssel haszn lja Gigaset k sz l k t Issued by Gigaset Communications GmbH Schlavenhorst 66 D 46395 Bocholt Gigaset Communications GmbH is a trademark licensee of Siemens AG Szanowny Kliencie Firma Gigaset Communications GmbH jest spadkobierca prawnym firmy Siemens Home and Office Communication Devices GmbH amp Co KG SHC kt ra z kolei przejeta segment produkt w Gigaset od firmy Siemens AG Wszelkie o wiadczenia firm Siemens AG i SHC kt re mo na znale w instrukcjach obstugi nale y traktowa jako o wiadczenia firmy Gigaset Communications GmbH yczymy wiele przyjemno ci z korzystania z produkt w Gigaset Say n M terimiz Gigaset Communications GmbH Siemens AG nin Gigaset i letmesini y r ten Siemens Home and Office Communication Devices GmbH 8 Co KG SHC nin yasal halefidir Kullanma kilavuzlarinda bulunan ve Siemens AG veya SHC tarafindan yapilan bildiriler Gigaset Communications GmbH tarafindan yapilmis bildiriler olarak algilanmalidir Gigaset ten memnun kalmanizi Umit ediyoruz YBAKAEMBIU nokynatenb KomnauHua Gigaset Communications GmbH siBriiercs NPABOMNPEEMHNKOM KOMIAHYY Siemens Home and Office Communication Devices GmbH amp C
40. ons already registered gt Under Base stations click on the registered and connected base station The De register button is activated gt Click on the De register button to deregister the selected base station The space in the list is released The name of the base station is replaced by the entry lt free base gt 23 Configuring the Gigaset M34 software Configuring power management You do not have to do without the Gigaset M34 USB functions even if your PC is in standby mode You can configure the Gigaset M34 software so that your PC is automat ically activated when an internal call is received gt Open the Gigaset M34 software and select the M34 USB gt Configuration option in the menu tree The options for PC activation are shown in the working area gt Under Wake up choose whether your PC is to be automatically activated for an internal call We recommend that you activate the Enable wake up with internal call option if you want to use your Gigaset M34 USB for Internet telephony When the Gigaset M34 USB PC adapter is operating together with a base station of type Gigaset 450 Y the PC is activated as soon as you press a display key on the S45 handset on which there is an M34 func tion Si Firmware update The firmware is the device software stored in your Gigaset M34 USB If your Gigaset M34 USB no longer functions correctly or if you want to operate it with more recent software
41. ows devices from various vendors to be combined Dialler Originally programs enabling a PC to access telephone connections e g the dialler in the Windows operating systems The term dialler is now used for programs that set up connections independently and unnoticed to preset special numbers This normally leads to very high connection charges Diallers can end up on a PC during an Internet download and then install themselves unnoticed To protect against diallers there are programs e g the dialler blocker which a PC can use to control the connections made and to allow only particular connections Dial up connections remote data transfer Aterm for transmitting digital data over the telephone network Well know dial up con nections are fax and Internet connections Dial up network Windows component for remote data transfer that connects a PC via a telephone line analogue or ISDN with an external network e g the Internet E Enquiry call You are making a call An enquiry allows you to temporarily interrupt the call to connect to a second external or internal party If you terminate the connection to this user imme diately then this was an enquiry call If you switch to and fro between the first and sec ond user it is called toggling Exchange Node in a public telephone network via which external connections are set up and redi rected A distinction is made between e g local exchanges and long distance exchanges
42. pen the Gigaset M34 software and select the M34 USB gt Configuration option in the menu tree gt Under Base stations click on one of the base stations that is registered but not con nected The Connect button is activated gt Click on the base station you want to connect gt Click on Connect 21 Configuring the Gigaset M34 software Changing device names When connected to a base station your PC is uniquely identifiable by its device name You can change this device name as required gt Open the Gigaset M34 software and select the M34 USB gt Configuration option in the menu tree The working area shows the current device name of the Gigaset M34 USB gt Enter the desired device name under Identification gt Name The maximum length of the device name is 10 characters gt Confirm your entry by pressing the return key Return Enter The new device name is sent to the connected base station If you also want to change the device name of your PC for connections to another registered base station first of all connect to the desired base station and then repeat this procedure Ox Calling the Gigaset M34 USB A connection between your handset and the Gigaset M34 USB allows you to access the PC through your handset The reguirement for this connection is that your handset is registered on the same base station as the Gigaset M34 USB To create the connection between your handset and the Gigaset M34
43. radas nos manuais de utiliza o dever o portanto ser consideradas como declara es da Gigaset Communications GmbH Desejamos que tenham bons momentos com o seu Gigaset Issued by Gigaset Communications GmbH Schlavenhorst 66 D 46395 Bocholt Gigaset Communications GmbH is a trademark licensee of Siemens AG K re Kunde Gigaset Communications GmbH er retlig efterf lger til Sie mens Home and Office Communication Devices GmbH amp Co KG SHC som fra deres side videreferte Siemens AGs Gigaset forretninger Siemens AGs eller SHCs eventuelle forklaringer i betjeningsvejledningerne skal derfor forstas som Gigaset Communications GmbHs forklaringer Vi h ber du f r meget glaede af din Gigaset Arvoisa asiakkaamme Gigaset Communications GmbH on Siemens Home and Office Communication Devices GmbH 8 Co KG SHC yri tyksen oikeudenomistaja joka jatkoi puolestaan Siemens AG n Gigaset liiketoimintaa K ytt oppaissa mahdollisesti esiintyv t Siemens AG n tai SHC n selosteet on t m n vuoksi ymm rrett v Gigaset Communications GmbH n selosteina Toivotamme Teille paljon iloa Gigaset laitteestanne K ra kund Gigaset Communications GmbH vertar r ttigheterna fr n Siemens Home and Office Communication Devices GmbH amp Co KG SHC som bedrev Gigaset verksamheten efter Sie mens AG Alla f rklaringar fr n Siemens AG eller SHC i anv ndarhandboken g ller d rf r som f rklaringar fr n Gigaset Communications G
44. se with your base station Installing the software and device drivers Base stations Internet access IP Internet telephony and PC control Maximum number of handsets C340 345 E F 6 C350 355 H 6 E450 455 z 6 54401445 6 450 455 F 6 S450Y 6 S645 6 SL440 6 SL550 555 F 6 CX340 345isdn 144 CX100 150isdn 6 5X100 150isdn E 6 SX203 253isdn 8 SX205 255isdn z 8 SX303 353isdn n 8 SX440 445isdn R 144 SX4501455isdn 144 SLX740isdn z 3 4170175isdn x 8 3070 75isdn S 8 For these base stations you must update the firmware on the Gigaset SX205 255 during instal lation One Gigaset M34 USB PC adapter and a maximum of 4 handsets can be registered on these base stations You can also use a type SL1 or S1 SL1 colour S1 colour C34 E45 S44 S45 SL55 or SL74 handset with one of the above base stations The base station is ready for use For details refer to the operating instructions for your base station Gigaset M34 USB PC adapter The Gigaset M34 USB should not be connected to the PC before installation Installing the software and device drivers Minimum PC reguirements Hardware ae 90 90 IBM AT compatible Pentium III with 500 MHz processor speed 128 MB RAM main memory 20 MB free hard disk memory 1 free USB port 1 CD ROM drive or 1 DVD drive Software Operatin
45. stalling configuring and operating the Yahoo Messenger with Voice in the operating instructions for these software packages You will find these operating instructions in PDF format in the gigaset m34 software man uals directory on the CD you received when you bought the M34 USB PC adapter When you select the Install software option the InstallShield Wizard for the Gigaset M34 software starts up This installation wizard guides you through the individual steps of the installation procedure gt Click on Continue to start the installation The directory in which the software is to be installed is shown gt Select the appropriate mode for installing device drivers We recommend that you do not change the Simple Recommended settings gt Click on Continue gt Select the folder where the selected software components are to be installed Click Continue to confirm the default installation directory 12 Installing the software and device drivers Or Click Browse to choose your own installation directory gt Click on Install If a dialog box appears during installation informing you about a missing I signature click Yes to continue the installation gt After installation of the software components click on Finish to confirm completion of the installation procedure You then need to reboot your PC You can only set up the Gigaset M34 USB PC adapter after rebooting gt Click on Yes t
46. t be unpacked gt Select the setup file dat for the firmware update gt Click on Open The version of the selected firmware is compared with the current version gt Click on Continue The firmware for your Gigaset M34 USB is updated The update can take up to several minutes 2 During the update you may not start any other PC applications You may not cancel the firmware update gt After the firmware update a message indicates whether the update was successful gt Click on Finish to close the Wizard for downloading new firmware program gt After completing the firmware update reboot your PC if you are prompted to do so 25 Operating the Gigaset M34 software Operating the Gigaset M34 software When started for the first time the Gigaset M34 software is opened with the preset view This view is divided into the following sections Gigaset M34 Software 10 x File Edit entry Options Help M34 USB Status Configuration Firmware update Menu tree Working area Menu bar and toolbar The menu tree shows all software components that have been installed with the Gigaset M34 software This is where you can select the component you want to use The components are sorted alphabetically in the menu tree If you install additional components the sorting of the entries therefore changes The working area shows the configuration dialog for the selected
47. this with a displayed mes sage You can then decide whether to accept or reject the second call Calls list The Calls list stores all the incoming and outgoing calls for the base station A Calls list filter differentiated the call types incoming outgoing missed The list stores the number called date and time of the call and in some cases the duration of the call CAPI Common ISDN Application Programming Interface Vendor independent PC device driver for ISDN connections A CAPI driver enables a PC to use an ISDN connection with fax and telephone software CF Call Forwarding See Call Forwarding CLIP Calling Line Identification Presentation This permits transfer of your personal phone number The person you are calling will see your telephone number CLIR Calling Line Identification Restriction This blocks transfer of your personal phone number The person you are calling will not see your telephone number 29 Glossary Comfort handset Handset with special features e g a backlit graphic display a larger directory capacity or the option of downloading ringtones CW Call Waiting See Call Waiting D DECT Digital Enhanced Cordless Telecommunication Standard for wireless telecommunications enabling the exchange of voice and multi media data between a base station and up to 8 end devices DECT is now accepted as a standard in more than 70 countries In conjunction with the GAP Standard this all
48. tion software down loads User manuals and any software supplied on a separate data medium shall be excluded from the Guarantee The purchase receipt together with the date of purchase shall be required as evi dence for invoking the Guarantee Claims under the Guarantee must be submitted within two months of the Guarantee default becoming evident Ownership of devices or components replaced by and returned to Siemens shall vest in Siemens This Guarantee shall apply to new devices purchased in the European Union For Products sold in the United Kingdom the Guarantee is issued by Siemens Home and Office Communication Devices GmbH amp Co KG Schlavenhorst 66 D 46395 Bocholt Germany Any other claims resulting out of or in connection with the device shall be excluded from this Guarantee Nothing in this Guarantee shall attempt to limit or exclude a Customers Statutory Rights nor the manufacturer s liability for death or personal injury resulting from its negligence The duration of the Guarantee shall not be extended by services rendered under the terms of the Guarantee Insofar as no Guarantee default exists Siemens reserves the right to charge the cus tomer for replacement or repair The above provisions does not imply a change in the burden of proof to the detri ment of the customer To invoke this Guarantee please contact the Siemens telephone service The relevant number is to be found in the accompanying user guide 36
49. ts wireless transmis sion of voice and multi media data over a range of a few meters The range of the con nection depending on the technical features of the connected device Unlike with infra red transmission Bluetooth devices do not need to be in line of sight 28 Glossary C Callback when the call is not answered If a user does not respond when called a caller can arrange an automatic callback As soon as the destination phone has completed a call and is free again the caller is rung back This service must be supported by the exchange The callback request is automat ically cancelled after about 2 hours depending on the network provider Callback when the number is busy If a caller hears the busy tone he or she can activate the callback function As soon as the connection is free the caller is rung back As soon as the caller lifts his receiver the connection is made automatically Call Forwarding CF Automatic redirecting of a call to a different telephone number A separate call forward ing number can be set up for each MSN Call forwarding can be triggered in the network provider s exchange or in the base station There are three kinds of call forwarding CFU Call Forwarding Unconditional CFB Call Forwarding Busy CFNR Call Forwarding No Reply Call Waiting CW Feature provided by a network operator An acoustic signal during a call indicates that another caller is waiting In addition ISDN phones indicate
50. utgoing calls This is necessary for example on a PABX that expects 0 or 1 for opening an outside line ACN International trunk prefix Can be preset in the base station as the access code for all calls abroad international or other local networks national Answering machine AM An answering machine accepts calls and records voice messages There are various designs of answering machine base stations can be eguipped with an internal answer ing machine function Analogue answering machines may be connected to a base sta tion Some network provider offer an answering machine function on the public tele phone network Authorisation Internal devices can be blocked in the base station for certain types of connection From certain devices e g devices only approved for internal calls no connections can be made with external phone numbers Calling an emergency number is always possible B B channel Use channel of an ISDN line with a transmission speed of 64 kbit s There are normally two B channels on an ISDN line This allows two calls to be made via the public tele phone network at the same time For dial up connections both B channels can be bun dled to increase the transmission speed Block dialling You first of all enter the complete number and then correct it as necessary Then lift the receiver or press the call key to dial the number Bluetooth New technology for wireless transmission of data Bluetooth permi
Download Pdf Manuals
Related Search