XIP – NVR04 LION Setup Guide
Contents
1. Please follow the proper power on procedures to avoid damaging the NVR e Connect all necessary components e g monitor and cameras before power on the NVR e Check the type of power source before plugging in the power cord to the NVR The acceptable power input is between AC110V AC240V e Switch on the power switch on the rear panel to power on the NVR NOTE Connect all IP cameras before powering on the NVR It takes about 4 minutes for a A 4CH model NVR to power on and display the images from all IP cameras While it takes 4CH models about 4 minutes the process may be slightly longer for 8CH models The amount of time may vary according to different IP camera models Xi Select Viewing Mode e Click on MODE repeatedly to select a preferred display mode The available viewing modes are full screen 4 window and 9 window 8CH models only Refer to the User s Manual for more details e Click on FREEZE to pause the current viewing image Basic Setup Enter the OSD main menu and setup some basic configuration of the NVR The basic configuration can be set via either the NVR or NVRRemote the remote software Enter OSD Main Menu e Click on MENU to enter the OSD main menu e Select the administrator account admin to login Enter the preset password 1234 e It is strongly suggested to change the password to prevent unauthorized access Date Time Setting Follow steps below to setup date time before the record2. View Live Camera 14 Select Picture Size 15 B 8 16 For more information on NVRRemote see User s Manual Xin 10 NVRRemote Playback Playback Remote Video e Click lt Play gt on the main window toolbar and then lt Remote Playback gt tab e The lt From gt and lt To gt on top of the screen display the date and time from which recorded video is available for playback e Choose lt Playback gt in lt Select gt field for playback recorded video Select the date and time of the segment to play back from the lt Start gt field Users can change the date and time either by typing desired numbers directly or using the arrow buttons Click lt OK gt to start the playback or click lt Close gt to abort Playback Local drv File e Click lt Play gt on the main window toolbar and then lt Local Playback gt tab e Click lt Open gt and the file selection screen is displayed Select the drv video file to playback and click lt OK gt Click lt OK gt to start the playback or click lt Cancel gt to abort View the video playback using the Playback controls To end the playback click lt Live gt to return to live video Playback Local avi Files e Start the windows media player or other media player from lt Start gt menu or any other possible access e Select lt File gt and then lt Open gt e Select the wanted avi file and click lt Open gt A NOTE The avi files for each channel ar
3. front of a channel to select or de select the channel Click on lt Event List gt to list the event video of the selected channels The list displays each event by date time triggered camera and alarm type The latest recorded event video will be listed on the top To exit the event list right click the mouse Click on the buttons below to view the previous or next pages of the Event List Click on the selected event record to playback the event video AN NOTE The event list displays only the first 1024 events as some events are deleted others are displayed Xin Playback Controls of Control Panel Buttons Time Frame of the Previous Time Bar Time Frame of the Next Time Bar Forward Playback Click repeatedly to increase speed by 1x 2x 4x 8x 16x or 32x Step Forward Only shows when playback is paused Change Viewing Mode Backward Playback Click repeatedly to increase speed by 1x 2x 4x 8x 16x or 32x ee Step Backward Only shows when playback is paused Pause Playback Return to Live Mode hr Scale Time Bar by 4 Hour Scale Time Bar by 12 Hour 24hr Scale Time Bar by 24 Hour 20 TR w Xi NVR Status Bar Icons Icons that will be displayed in the status bar are listed in the following table with their descriptions Item Icon Description Item Icon Description 1 ica os Soe Poe Das on a e Ja eee E E e ae HE Forward Playback Speed 1X 2x ax Be HDD Usage
4. 16x 32x so Backward Playback Speed 1X 2X 4x 8x 16x 32x User s Authority Level Xi Connect the NVR via the Remote Software Setup Requirements e Make sure the PC is connected to the Internet e Obtain IP address of the UltraEco H 264 NVR To check the IP address of the NVR click on MENU and select lt System gt gt lt Network Setup gt gt lt LAN Setup gt gt lt IP gt to check the IP AN NOTE The NVR Remote does not support 64 bits IE and IE under Win Metro A NOTE Make sure the IP address of the NVR is not set to 192 168 50 xxx Otherwise network conflict will occur against the default IP of the built in PoE hub Changing Internet Setting The UltraEco H 264 NVR only supports 32 bit IE browser However the NVR does not support IE browser under WinMetro mode e Start the IE select lt Tools gt from the main menu of the browser then lt Internet Options gt and then click the lt Security gt tab e Select lt Trusted Sites gt and click lt Sites gt to specify its security setting e Uncheck Require server verification https for all sites in this zone Type the IP address of the unit in field and click lt Add gt to add this website to the zone e Inthe Security Level area click lt Custom Level gt Under lt ActiveX controls and plug ins gt set all items to lt Enable gt or lt Prompt gt e Click lt OK gt to accept the settings and close the lt Security Setti
5. XIP NVRO4 LION Setup Guide Package Content Inspect the packaging carton Make sure the XIP NVR04 LION is properly delivered Remove all items from the box and make sure the box contains the following items Power Adaptor Control Power Cord XIP NVRO4 LION H264 NVR i USB Mouse Setup Guide Software CD Front Panel 1 23 4 O O USB 2 0 Port The USB 2 0 port allows users to connect an external USB device to the i unit such as a USB ThumbDrive or a USB mouse Record LED It blinks when videos are being recorded Alarm LED It lights up when an alarm is triggered Network LED It lights up when network is connected In addition it blinks when data is being transmitted via the network Xi Rear Panel gt 1 23 4 an i LAN DC50 IN USB EE 6 7 8 Main Monitor VGA A VGA output connector is for connecting to a VGA main monitor LAN 10 100M The NVR is capable of networking and it allows the videos to be viewed over the LAN network or the Internet by using the Internet Liam Explorer USB 2 0 Ports The USB 2 0 ports allow users to connect external USB devices to the unit such as a USB ThumbDrive or a USB mouse The PoE ports offer direct connections to 4 IP cameras for 4CH PoE Ports models and 8 IP cameras for 8CH models The IP cameras can be olug and play if the function is enabled in the OSD menu Main Monitor An RCA connector is provided t
6. e stored separately Therefore the video can be played back in single channel full screen mode only Playback Event Video e Click SEARCH on the main window toolbar The Event List appears e Scroll through the Event List and highlight the interested events e Double click on the desired event to view the event video Playback Controls Fast Backward Fast Forward Step Backward Step Forward Play Pause
7. ick on End and playback will start from the specified End time Click on Select and choose date or time field Click on the UP DOWN buttons to adjust the values Click on Select again to confirm or right click to abort Click on lt Begin Playback gt to start playing back recorded video of the selected time Click on PLAY STOP again to return to live video A NOTE If there is no available recorded video that matches the specified time and date the unit starts to playback from the next available video Calendar Search Click on SEARCH to enter the Search menu Click on lt Calendar Search gt and a calendar will show up Select any date shown in underlined font which means recording data are available The table shown on the left will display available videos of each channel within the selected date The videos are classified into four categories Normal Motion Alarm In and Video Loss shown as four different tabs on the top Then select a preferred time from the time bar Alternatively specify the values of date hour minute second under lt Select gt on the right The lt From gt and lt End gt buttons allows users to playback video from the beginning or end of the database Click on lt Begin Playback gt to start playing back the selected video Search by Event Click on SEARCH to enter the Search menu To search event video that was recorded on a specific camera check or un check the box in
8. ing starts Refer to the User s Manual for advanced setup of Time Sync function e Select lt Date Time gt in the System menu e Select date or time and adjust the value by clicking on the UP DOWN buitons e The new date and time settings take effect after the changes are confirmed Language Setting lf users wish to change the language of the NVR system follow the steps below e Select lt Language gt in the System menu e Click on the DOWN buttons to choose the desired language Network Setup Configure the LAN setup for the NVR to properly function with Ethernet connection The default ID of the UltraEco H 264 NVR must be changed to avoid network conflicts e From the OSD main menu select lt System gt gt lt Network Setup gt set the lt LAN Select gt item to lt LAN gt or lt PPPoE gt according to the network application and enter lt LAN Setup gt e For DHCP users set the DHCP to lt ON gt The IP address Netmask Gateway and DNS settings are retrieved from network servers DHCP is dynamic that the settings change from time to time e For Non DHCP users set the DHCP to lt OFF gt IP address Netmask Gateway and DNS settings must be set Please obtain the information from the network service provider e To change the IP address Netmask Gateway and DNS value click on the lt Num gt button to display the number pad and input users preferred setting values e PPPoE users must set the lt PPPoE Account gt l
9. ngs gt screen Using the Remote Software e Start the IE and enter the IP address of the UltraEco H 264 NVR in the address bar e The ActiveX controls and plug ins dialog will show up twice for confirmation click lt YES gt to accept ActiveX plug ins The NVRRemote plug ins will be downloaded and installed on the PC automatically when the connection is successfully made A NOTE Do not enter any leading O characters in the address for example 192 068 080 006 should be entered 192 68 80 6 A NOTE If the default trigger port 80 is changed into another one take port 81 for example users should enter the IP address as 192 68 80 6 81 e Version verification starts automatically to verify whether NVRRemote was installed This process may take up to 30 seconds e When the software is completely downloaded and installed the Login Screen is displayed e Enter username and password The default username and password is admin and 1234 Xi 9 The following picture shows the display window of the NVRRemote 1 6789002 B U 5 1 3 rr 4 ee Go BB Refer to the table below for brief description of functional items Item Description Item Description i instant Recording 9 SearchEventList 2 SmoothentheImage 10 Capture Snapshot Audio On Off M1 4 3 Viewing Aspect 4 andwidth Normal Dual Stream Download NVRPlayer Playback Video Setup Menu 3 12 5 Display Mode _ _ 13 6
10. o output audio associated with the Audio Out main monitor Main Monitor An HDMI connector is provided for connection to a displaying device HDMI that transmits data digitally to show the best video quality Connect the power supply cord shipped with the NVR Use of other power supply cords may cause overloading Switch it on to power on the NVR 2 After shutting down the NVR system from the OSD main menu switch it off to power off the NVR NOTE Currently the plug and play function is only supported for specific IP camera models Please contact the supplier for more information Furthermore the IP address of the IP cameras has to be set to default or static before connecting to the NVR Otherwise the NVR will not be able to recognize the existence of the IP cameras Xi Live Panel Buttons The functional buttons are displayed in the Live Panel when the mouse pointer moves to the right of the screen Refer to the chart below for definition of each button Item Icon Description Item Icon Description Item Icon Description o oo O 0e D E a So NOTE The item 9 lt Sequence gt is only supported by 8CH models Dome Camera Control IP Camera Status Icons The table below describes the connection status of IP camera at Live mode Description Icon Description Icon Description Connecting IP Camera Successful Connection No Connection l Failed Connection Ea Resolution Oversize o Power On the NVR
11. t PPPoE Password gt and lt PPPoE Max Idle gt e When the settings are complete click on the item again to confirm and save the settings or right click to abort e Aid A Dome Camera Control Dome Camera Connection Refer to the following figures Connect the dome camera to any PoE port of the NVR via an RJ 45 Ethernet cable The PoE ports of 4CH models supply a total of 30W power source while the PoE ports of 8CH models supply a total of 60W power source Each port is limited to at most 15W usage If the connected dome camera requires power exceeding the limited power source please connect an additional power source Power RJ 45 Ethernet Cable Optional V 23 gt DC50 IN i a NOTE The 30W 60W power is shared by all ports but not equally shared Take 4CH A models for example if the first two ports used up to 15W the maximum of each port the remaining ports will not have power supply Thus the remaining ports will just be network connection ports Control Buttons in Dome Camera Control Panel icon Description Icon Description Icon Description Q Oe Be m Set Go Preset Points oO Return to Live Mode a pane Iie Fens o to the Left 5 Move the Lens to the Right Move Up the Lens Move Down the Lens Xi Basic Playback Operation Search By Time Click on SEARCH to enter the Search menu Click on From and playback will start from the specified From time Cl
Download Pdf Manuals
Related Search