User`s manual. Digital input RS232. Connection and
Contents
1. CAN32BITRO CAN32BITR4 50 RS485 0 51 RS485 1 52 RS485 2 Settings of parameters display in the CUBS indicator Example Request CUB5 1 0 Reply CUB5 RS2320 1 RS2321 0 2 3 to reset the terminal send Reset command Make sure the terminal correctly transmits the information to the indicator display to do this you should visually compare the values shown on the display with the indications which are shown in the Troubleshooting tab of the Configurator There should be a tick in the RS232 0 RS232 1 field Pic 8 SPA GalileoSky LLC Page 4 User s manual Digital input RS232 Connection and operation of CUBS indicator Picture 8 Checking of matching of displayed data Connection of the CUB5 to the GalileoSky terminal via RS232 interface is completed the terminal is ready to operate SPA GalileoSky LLC Page 52. s manual Digital input RS232 Connection and operation of CUBS indicator 1 3 press Apply button 1 4 go to the Device tab of the Configurator and reset the terminal using Reset button 2 Setting via commands 2 1 send RS2320 7 or RS2321 7 command to the terminal to connect the indicator 2 2 send CUB5 command with the following parameters to the terminal Command format CUB5 NO N1 Parameters NO N1 parameter number displayed on the indicator connected to RS232 0 RS232 1 port Parameters O speed accurate within 0 1 km h 1 directional angle accurate within 0 1 2 external supply voltage mV 3 internal accumulator voltage mV 4 temperature inside the Terminal C 5 mileage according to the GPS GLONASS unit accurate within 0 1 km 6 input INO 7 input IN1 8 input IN2 9 input IN3 10 RS232 0 12 temperature sensor 0 C 13 temperature sensor 1 C 14 temperature sensor 2 C 15 temperature sensor 3 C 16 temperature sensor 4 C 17 temperature sensor 5 C 18 temperature sensor 6 C 19 temperature sensor 7 C 20 CAN Total fuel consumption I 21 CAN Tank fuel level accurate within 0 1 22 CAN Coolant temperature C 23 CAN Engine speed 24 CAN mileage accurate within 0 1 km 25 39 CAN8BITRO CAN8BITR14 40 44 CAN16BITRO CAN16BITR4 45 49
3. User s manual Digital input RS232 Connection and operation of CUBS indicator Necessary tools devices materials To connect the CUBS indicator hereinafter CUB5 to the GalileoSky terminal hereinafter terminal one should have 1 Electrical tools Picture 1 2 Set of connecting wires Picture 2 3 Windows based computer with the installed program of configuration of GALILEOSKY terminals Configurator It is recommended to install the latest version of the program from the site http 7gis ru support konfigurator html Gp Picture 3 SPA GalileoSky LLC Page 1 User s manual Digital input RS232 Connection and operation of CUBS indicator General information CUB5 is a segment 8 bit display which can be connected to the terminal using RS232 interface It can display current sensors data CAN bus data mileage and so on Pic 4 Specific displayed parameter is selected in the process of settings of the terminal through the Configurator Information in the indicator is updated once a second Picture 4 Different modifications of CUB5 indicator Connection of CUB5 via RS232 interface Before connecting make sure that there is an additional card with the connector for the RS232 interface on the backwall of the indicator Pic 5 Additional 4 board RS232 oA wm fe 5 m S Picture 5 Checking of availability of additional card Connection of CUB5 via RS232 int
4. erface is carried out in accordance with the scheme of Picture SPA GalileoSky LLC Page 2 User s manual Digital input RS232 Connection and operation of CUBS indicator Rear panel CUB5 Picture 6 The scheme of connection of CUB5 to RS232 input For v1 8 5 or v2 2 8 terminals which have the second RS232 port it is possible to use still RXD1 and TXD1 contacts ATTENTION Grounds GND of the terminal and the CUB5 must be connected RS232 contacts must be connected strictly according to the scheme RX of the CUB5 TXDO of the terminal and TX of the CUBS RXDO of the terminal The CUB5 power supply is provided separately Setting of RS232 0 RS232 1 input of the terminal to display information on the indicator can be performed in two ways 1 Setting via the Configurator Pic 7 1 1 Go to the Setting tab gt Digital inputs of the Configurator and select CUBS indicator 1 2 in the CUBS Indicator block choose the parameter information on which you plan to bring to the CUBS display a RS232 RS232 0 function Digital fuel sensors filter length R5232 0 without filtration Photocamera Write period D sec oh ok r Write and send period sec Recording in geofence always make photo ha Size px Require an acknowledgment from server Indicator CUBS R5232 0 temperature mileage Picture 7 RS232 input setting in the Configurator SPA GalileoSky LLC Page 3 User
Download Pdf Manuals
Related Search