Antik EN 9200 / 9400 Encoder MANUAL
Contents
1. Output PMT PID set PMT PID valid range from 32 to 8190 decimal Output Video PID set Video PID valid range from 32 to 8190 decimal Output Audio PID set audio PID valid range from 32 to 8190 decimal Output Service PID set Service PID valid from 32 to 8190 decimal Output Service Name set the service name for the encoded transcoded channel The length should be less than 24 characters Output PCR PID set PCR PID valid range from 32 to 8190 decimal Null Filter switch on to filter away the null packages or so called unstuffed stream will be sent out via TS IP or ASI output port Switch off to keep the null packages within the stream or so called stuffed stream will be sent out via TS IP or ASI output port By removing the null packets to have lower bit rate but less PCR accurate than normal SPTS Note the Null packet is essential for DVB applications don t remove them Transcoder Program under transcoder operating mode select the program that to be transcoded in the drop down list Note the selection is valid to the video only the paired audio should be selected in Transcoder Audio PID Transcoder Audio PID under transcoder operating mode select the audio PID that to be transcoded in the drop down list note the audio PID can be anyone from the ASI or IP input but not to be banded with the video Quick Guide it is recommended to set CBR mode and switch off the GOP Adaptive to have a relative constan2. Source configure the TS source for the built in remux ASI set ASI input as the source of the built in remux IP set IP input as the source of the built in remux Note this sub menu is displayed only when the IP I O is configured as full duplex mode ASI Out Source configure the TS source for ASI output port Remux the TS generated by the built in remux will be delivered to the ASI output port ASI Input the TS inputted via ASI input will be looped through via the ASI output port Encoder 1 the SPTS generated by encoder transcoder 1 will delivered to the ASI output port Encoder 2 the SPTS generated by encoder transcoder 2 will delivered to the ASI output port Encoder 3 the SPTS generated by encoder transcoder 3 will delivered to the ASI output port Encoder 4 the SPTS generated by encoder transcoder 4 will delivered to the ASI output port EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder Service ID 4000 TS ID 00016 Output Bit Rate 6000Kb s ASI Out Source Remux TS IP Out Source configure the TS source for IP output port Remux the TS generated by the built in remux will be delivered to the IP output port ASI Input the TS inputted via ASI input will be looped through via the IP output port Encoder 1 the SPTS generated by encoder TS IP Out Source ASI transcoder 1 will delivered to the IP output port Input TS IP Out Source Encoder 2 the SPTS generat
3. video3 Input Format 1920x1080i 24 8 Video4 Input Format 1320x1080i 25 Alarm Encoder 1 Format is Different ASI Input Unlock Manual Refresh Interval 7 2 Configuration All configuration for encoding transcoding TS IP I O built in Remux and output can be found under the Configuration tab on the webpage Click the button Apply to submit your configuration or click the button cancel to undo your configuration as it shown in figure below 7 2 1 Encoder 1 4 There are four encoder transcoder functional blocks integrated on one EN9200 EN9400 blade each functional block can work independently Click on the Enceder 1 10 configure the block 1 and SO On Work Mode each encoder transcoder functional block can be configured as different operation mode 19 www antiktech com MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder 8 Transcoder tss O AV 20 independently H 264 the current encoder transcoder is set to H 264 SD HD Encoder MPEG 2 the current encoder transcoder is set to MPEG 2 SD Encoder MPEG 2 to H264 the current encoder transcoder is set to MPEG 2 to H 264 Transcoder H264 to H264 the current encoder transcoder is set to H 264 to H 264 Transcoder H264 to MPEG 2 the current encoder transcoder is set to H 264 to MPEG 2 SD Transcoder MPEG 2 to MPEG 2 the current encoder transcoder is set to MPEG 2 to MPEG 2 SD Transcoder Encoder Bit Rate set the output bit rate of the current enc
4. 20p 50 25 720x480i 29 97 720x576i 25 1920x1080i 29 97 1920x1080i 25 Z Video Bit Rate Video Bit Rate 7000Kb s 0 99699Kb s set the video bit rate 10 Aspect Ratio 4 3 set video aspect ratio to 4 3 16 9 set video aspect ratio to 16 9 Video Max Bit Rate set the maximum video bit rate Video Min Bit Rate set the minimum video bit rate GOP Size 0 63 set the GOP size valid range from 0 63 Note the bigger the value better the compression ratio for video but longer the latency of encoding GOP Structure IBBBP IBBP IPPP IBP set the structure of GOP GOP Adaptive ON GOP structure and size is adaptive and may change according to different video scenes OFF GOP structure and size is fixed as the settings Output Video Format Auto Settings video resolution and frame rate will be same as input Manual Settings Horizontal set the resolution in horizon Vertical set the resolution in vertical Frame Format Progressive set the progressive scanning to the output video Interlaced set interlaced scanning to the output video Image Settings the menu is displayed on EN9200 EN9400 Saturation Control set the saturation of the picture valid range 100 100 Hue Control set the hue of the picture valid Aspect Ratio 4 3 Video Max Bit Rate 10000Kb s Video Min Bit Rate 0000Kb s GOP Size 61 GOP Structure IBBBP GOP Adaptive ON Ou
5. C LC MPEG4 AAC LC Sampling Rate 48KHz MPEG1 Layer Il 32 192Kbps mono 64 384Kbps stereo MPEG2 AAC LC MPEG4 AAC LC 56 256Kbps mono 112 512Kbps stereo Recommend Compression Bit Rate Transcoding MPTS MPEG2 MP ML MP HL Input Standard MPTS H 264 AVC Main High Baseline Profile L4 0 or less but not FMO ASO amp RS of Baseline MPTS and or un stuffed TS MPEG2 MP ML Output Standard MPTS and or un stuffed TS H 264 AVC Main High Baseline Profile L4 0 or less but not include FMO ASO amp RS of Baseline DVB ASI Input Input Interface BNC Female 750 Maximum Bit Rate 100 Mb s Data Type Byte Packet Length 188 204 Bytes Signal Level 200 880mVp p DVB ASI Output 9 www antiktech com MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder technology Signal Level 800 80mV 80Mb s note Full Duplex mode 200Mb s note Multiple Output mode 2 x D Sub15 with D Sub 15 to BNC female adapter cablings total 4 sets of inputs see Model List owe Operating Humidity 10 90 Non condensed Maximum Effective Bit Rate CVBS In amp Analog Audio In 4 Order Information e EN9200 S EN9400 S EN9200 H EN9400 H EN9200 C EN9400 C HD SD SDI with Embedded Audio HDMI with Input Embedded Audio mi 1 1 L A Output TSIP GbE e e j e e ee Audio AAC LC Encoding e jeje Jo CVBS amp acc Audio 9 Front panel and rear pan
6. MANTIK technology User s Manual Brighten Your Digital View EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder www antiktech com MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder technology Contents Notice Before Using the Device 1 Overview 2 Features 3 Technical Specifications 4 Order Information 5 Front panel and rear panel instructions 5 1 Front panel 5 2 Rear panel 6 Operation instructions using EN9200 EN9400 programmer 6 1 Overview of the Menu 6 2 Description of menu 7 Web Control 7 1 Status 7 2 Configuration 7 3 System 8 Recommended Configuration 9 Installation 10 Accessories Notices COPYRIGHT Copyright 2014 ANTIK Technology Not to be copied used or translated in part or whole without Beijing Jaeger prior consent in writing except approval of ownership of copyright and copyright law WARRANTY This warranty does not cover parts which may become defective due to misuse of the information contained in this manual Read this manual carefully and make sure you understand the instructions provided For your safety be aware of the following precautions WARNING IMPORTATNT SAFETY INSTRUCTIONS CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING To reduce the risk of fire or electric shock do not expose this apparatu
7. P interface is disconnected Gigabit Out Switch Enable Disable Gigabit Out Switch ON Gigabit Out Status UDP Packets s 3610 Column FEC Pkts s Row FEC Pakts s Gigabit Out Status UDP Packets s 3610 Column FEC Pkts s Row FEC Pakts s Protocol UDP set UDP protocol to IP output Protocol UDP RTP set RTP protocol to IP output TS Pkts Per UDP set the number of TS packets that can be carried by each UDP TS Pkts Per UDP 7 packet valid range from 1 7 TS IP Gigabit Mode Full Gigabit Output 5 ee Time To Live set TTL to the output IP packets Time To Live 1 255 Duplex valid range from 1 255 Type Of Service Min Delay Max l l uM l Type Of Service Min Reliability Max Throughpu Min Monetary je elay Cost Normal Uni Multi IP Address set the destination IP Uni Multi address Addres 238 069 070 001 Uni Multi UDP Port set the destination port Uni Multi UDP number valid range from 1 65535 ProM PEGFEC ProMPEG FEC Switch Enable Disable l l Switch Disable NE Gigabit Address set the IP address of the IP Gigabit Adress Gigabit Local port 010 010 080 060 www antiktech com 17 technology MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder 8 Transcoder Gigabit Subnet Mask set the net mask of the Gigabit Subnet Mask IP port 255 255 255 000 Gigabit MAC Address display the MAC address of the IP port ee Gigabit Gateway set the gateway of the IP Gi
8. SC SD video while total bit rate 700Kb s Independent Vertical amp Horizontal pixel scale Transcoding from MPEG2 to H 264 AVC amp vice versa VBR amp CBR mode for encoding transcoding Audio coding MPEG1 Layer II MPEG2 4 AAC LC note see Chapter 4 Order Information SNMP amp HTTP WEB for monitoring amp control Fit to EN9200 EN9400 programmer chassis V V V V V V v 3 Technical Specifications Video Input amp compression Coding Video Input Interfaces 4x HDMI 4x SDI or 4x CVBS note see Chapter 4 Order Information H 264 AVC BLP MP HP L4 0 or less MPEG 2 MP ML note see Chapter 4 Order Information 4 2 0 10 bit YCbCr Coding Profile amp Level Sampling Format Compression Bit Rate 600K 20Mbps 10801 1920x1080 25Hz 29 97Hz 30Hz SMPTE274M 1 20Mb s Video Resolution amp Recommend 720p 1280x720 25Hz 29 97Hz 30Hz SMPTE296M 1 20Mb s Compression Bit Rate H 264 480i 720x480 29 97Hz SMPTE656M 600K 10Mb s 576i 720x576 25Hz SMPTE656M 600K 10Mb s Video Resolution amp Recommend 480i 720x480 29 97Hz SMPTE656M 3 5 10Mb s Compression Bit Rate MPEG 2 576i 720x576 25Hz SMPTE656M 3 5 10Mb s Video Resolution Down Scaling Vertical amp Horizontal adjustable respectively frame rate is not scalable Aspect Ratio 4 3 16 9 Selectable Audio Input amp Compression Coding Audio Input Interfaces HDMI SDI Embedded or Analog note see Model List MPEG1 Layer II Audio Codec MPEG2 AA
9. break the device and cause serious accident Fix the front and rear covers onto the EN9200 or EN9400 Connect all input output cables and Ethernet cables Plug the power cable into EN9200 or EN9400 The POWER Indicator LED A4 should be green and always light on during working The EN9200 EN9400 needs 1 5 2 minutes to boot up completely Connect EN9200 9400 to configure locally or open a web browser on a connected PC and configure remotely SUM MEUM Seen MANI DUNT AIRE Bedr NOSTRAE Arn tored 666 6666 YYYY oo 0 OO I 66 se c z n oe aal E p EN ER 22 2a f mt MANTIK PNE D D ETIR 2 f ojo oo 2 2 s aaa 0 0 2 E 0009 CHO t jJ 000 9 L EN9200 9400 2 slots single power supply 10 Accessories Accessories for EN9200 EN9400 Front panel 1 PC Rear panel 1 PC CD ROM 1 PC BNC Connector Cable 1 PC Certificate of quality Guarantee card 1 PC 30 MANTIK Ve o ino o A V ANTIK Technology rskeho 10 040 01 Ko ice Slovak Republic Phone 421 55 30 12345 E mail info antiktech com
10. e Status Encoder 2 Bit Rate Display encoder transcoder 2 bit rate nt Encoder 3 Bit Rate Display encoder transcoder 3 bit rate Encoder 4 Bit Rate Display encoder transcoder 4 bit rate S 9 www antiktech com MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder kennel 0 4 V ASI Out Bit Rate Display ASI output bit rate SS BED en Od X 3 En1 Work Error Encoder Transcoder function faulty En2 Work Error Encoder Transcoder 2 function faulty AINE En3 Work Error Encoder Transcoder 3 function faulty En4 Work Error Encoder Transcoder 4 function faulty TS IP Input Unlock TSoverlP input invalid ASI Input Unlock ASI input invalid Encoder Select Encoder 1 the encoder transcoder 1 is active for configuration Encoder 2 the encoder transcoder 2 is active Encoder Select for configuration Encoder 3 the encoder transcoder 3 is active for configuration Encoder 4 the encoder transcoder 4 is active for configuration Encode Start Enter Yes the settings will be applied to the selected encoder transcoder and start it to Encode Start out encode transcode Encoder Exit No cancel the settings to the selected encoder transcoder which wil keep the previous status Video Rate Ctl Video Rate Ctl VBR CBR set constant bit rate mode VBR set variable bit rate mode Input Video Format Input Video Format Video Settings 1280x720p 50 1280x720p 29 97 1280x720p 1280x7
11. e destination IP Uni Multi IP Address Gaand Se address for the IP output 238 069 070 001 Encoder 1 Channel Uni Multi UDP Port set the destination port Uni Multi UDP number valid range from 1 65535 Encoder 2 Channel Encoder 3 Channel Encoder 4 Channel Gigabit Out Switch TS IP Channel TS IP Gigabit ON OFF to switch on off the uni multicast Gigabit Out Switch ON output Mode Gigabit Address set the IP address of the IP IP Board IP Multiple port Address 10 10 80 60 Output Gigabit Subnet Mask set the net mask of the IP Board Net IP port Mask 255 255 255 0 Gigabit Local Gigabit Gateway set the gateway of the IP IP Board port Gateway 10 10 80 1 Gigabit MAC Address display the MAC IP Board MAC Address address of the IP port 16 Protocol UDP set UDP protocol to IP output Protocol UDP RTP set RTP protocol to IP output TS Pkts Per UDP set the number of TS packets that can be carried by each UDP TS Pkts Per UDP 7 packet valid range from 1 7 Time To Live set TTL to the output IP packets Time To Live 255 valid range from 1 255 Type Of Service Min Delay Max l m l Type Of Service Min Reliability Max Throughput Min Monetary Delay Cost Normal Gateway MAC Address set the MAC address l _ Gateway MAC Address of the gateway under which the unit is fF FF FF FF PAF connected Link Status Gigabit Status Linked 1000M the IP interface is well linked Disconnect the I
12. ed by encoder transcoder 2 will delivered to the IP output port Encoder 3 the SPTS generated by encoder transcoder 3 will delivered to the IP output port Encoder 4 the SPTS generated by encoder transcoder 4 will delivered to the IP output port IP Address set the IP address of the 9200 9400 valid range from 0 0 0 0 255 255 255 255 Subnet Mask set the net mask of the IP Address 10 10 70 48 9200 9400 valid range from Local Setting Net Mask 255 255 255 0 0 0 0 0 255 255 255 255 Gateway 10 10 70 1 Gateway set the gateway of the 9200 9400 valid range from 0 0 0 0 255 255 255 255 MAC Address to display the MAC address of the 9200 9400 Trap IP Address set the IP address of the 1 ra Remote Setting SNMP Trap server valid range from j Address 10 10 70 25 0 0 0 0 255 255 255 255 Edit Product name user allows to rename the unit press Enter and key in the name of the System Product Name l l l unit then press Enter to confirm the setting or press Exit to cancel l Software Version display display the Software Version l software version Note the IP address of the device is not reset to Factory Default the factory setting While Enter Yes press Enter to recall the factory press the button A8 IP Factory Default l l default settings Reset via the front panel Exit No press Exit to cancel the IP address is reset to the factory setting 10 10 70 48 _ dM MEE unit WEB Login ID Edi
13. el instructions 5 1 Front panel MANTIK technology EN9400 A1 ll TL A2 Control a A3 TS IP A4 E M AS em AG AT nad 9 Reset A8 o Handset www antiktech com 7 MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder technology A1 USB A2 Control A3 TS IP A4 Power Ad ASI IP A6 Encoder AT Reset A8 IP Reset A9 Handset Used to upgrade software version of this device Network management interface for remote control GbE Full Duplex interface for TS output and input Power LED indicator green light means power supply is on ASI I O and IP I O Alarm indicator green light means ASI I O and IP I O ports are running red means either ASI I O or IP I O or both are malfunctioning 4 LED indicators for 4 encoder transcoder separately in green means encoder transcoder is running Red means the corresponding encoder transcoder s is are malfunctioning Used to reset the device s settings Used to reset the IP address to factory setting Used to connect EN9200 EN9400 programmer handset unit for control 9 2 Rear panel of EN9200 EN9400 60 O BI 1 MANTIK reach ole a wy CE re X 241xEC C Rear Panel B1 ASI IN B2 ASI OUT B3 CVBS IN B4 HDMI B5 HD SDI IN 1 ASI Out 2 99 HDMI 2 HDMI 4 MANTIK MANTIK CE FE X CE Fe X 241xEC H Rear Panel 241xEC S Rear Panel ASI input interface 2 ASI output interface output in mirror 4 SDI input inte
14. gabit IP Gateway Gateway MAC Address set the MAC address mE Gateway MAC Address of the gateway under which the unit is ff fF ff fF FF FF ff connected Gigabit Input Status Lock the IP interface is well linked and there is valid IP input Unlock the IP interface is linked but no valid IP input Uni Multi Address set the uni multicast target Uni Multi address of the IP input Addres 238 069 070 002 Uni Multi UDP Port set the target port number of the uni multicast IP input valid range from 1 65535 Uni Multi UDP 01234 Column FEC UDP Port set the port for Column FEC UDP Port Gigabit Input Column FEC 01236 Row FEC UDP Port Row FEC UDP Port set the port for Row FEC 01238 TS Clock Recovery Auto it is suggested to set Auto when there is accurate PCR carried by the inputted TS IP Fixed Rate when fixed rate is selected user TS Clock Recovery Auto has to configure a bit rate to regenerate the TS clock The configured fixed bit rate has to be a little bit higher than the bit rate of the inputted TS IP 7 Web Control EN 9200 EN 9400 has an integrated web server This web server allows the configuration and status requests with a standard web browser To operate a EN9200 EN9400 unit first make sure the IP Control A2 port is well connected in the network and could be pinged by the host PC and then enter the IP address of the EN9200 EN9400 into the browser there will be a pop up
15. h local encoders then sends the new one over IP amp ASI out In the second mode Multiple output which delivers up to five streams over IP There are four stuffed or un stuffed SPTS and one MPTS from internal reMultiplexer over the IP with different Unicast or Multicast IP addresses To change the TS IP operation mode please refer to chapter 7 3 1 System Device The management interface is different under two operation mode Multiple Output Mode Gigabit Output Under multiple output operation mode user can give five different uni multicast destination addresses and port number to each encoder transcoder and the built in remux and each IP output can be switched ON OFF independently The source for TS IP output 1 4 is corresponding to the encoder transcoder 1 4 respectively and cannot be changed The default source for TS IP output the 5 uni multicast output is the built in remux To change the source please refer to chapter 7 2 4 Configuration Output Note the page below is displayed only when the TS IP operation mode is Multiple Output mode To change the TS IP operation mode please refer to chapter 8 3 1 System Device ssd IP Address 10 10 80 67 Status f Configuration System Encoder 1 Gigabit Out Encoder 2 g Encoder 3 Soe ae Encoder 1 Uni Multi IP Address 238 169 FO 1 Switch ON TS IP Uni Multi UDP Port 1234 Ean Tui Encoder 2 Uni Multi IP Address 238 leo le 2 Switch ON Local Settings Uni Mult
16. i UDP Port 1235 Remux Encoder 3 Uni Multi IP Address 238 69 70 3 Switch ON Output Uni Multi UDP Port 1236 Encoder 4 Uni Multi IP Address 238 69 70 LA Switch ON Uni Multi UDP Port 1237 TS IP Uni Multi IP Address 238 69 70 1 5 Switch OFF Uni Multi UDP Port 1238 Apply Cancel Local Settings Set the parameters for the TS IP output port Note the Gateway MAC address means the MAC address of the gateway under which the device is connected This parameter has to be configured when the TS IP output is delivered to a destination 22 Brighten Your Digital View that is not located under the same subnet Status Configuration System Encoder 1 Encoder 2 Encoder 3 Encoder 4 TS IP Gigabit Out Local Settings Gigabit Address Gigabit Subnet Mask Gateway IP Address Gigabit MAC Address Remux Output Protocol TS Pkts Per UDP Time To Live Type of Service Gateway MAC Address Full duplex Output Mode Gigabit Input ssd IP Address 10 10 80 67 Gigabit Local Settings 10 20 180 60 255 1255 255 0 10 420 80 1 00 06 f4 32 9d 5d UDP v Z 255 Min Delay v ff ff ff ff ff ff Under full duplex operation mode the device supports single uni multicast reception Set the uni multicast targe IP address and port number in the page The Column and Row FEC UDP ports have to be configured if Pro MPEG protocol is used in the IP signal inputted Note the page below is displayed on
17. ials may be copyrighted Unauthorized recording of copyrighted material may be against the copyright laws in your region Also use of this product with cable television transmissions may require authorization from the cable television operator or transmitter owner VENTILATION Do not expose the product to high temperatures such as placing it on top of other product that produce heat or in places exposed to direct sunlight or spot lights e The ventilation slots on top of the product must be left uncovered to allow proper airflow into the unit e Do not stand the product on soft furnishings or carpets e Do not stack electronic equipment on top of the product Do not place the product in a location subject to extreme changes in temperature The temperature gradient should be less than 10 degrees C hour Place the product in a location with adequate ventilation to prevent the build up of heat inside the product The minimum ventilation space around the unit should be 7 cm The ventilation should not be impeded by covering the ventilation openings with items such as newspapers table cloth curtains etc POWER SOURCES The product is not disconnected from the AC power source mains as long as it is connected to the power outlet or wall socket even if the product is turned off e If the product will not be used for a long period of time disconnect it from the AC power outlet or wall socket Before Using the Device Tha
18. ion User can check versions of various functional blocks of the device as it shown in figure below ssd IP Address 10 10 80 67 i Device Version Network Version Preset Software Version 2411EC CO002 Web Version 0106 FPGA Version OD Encoder Version 01 Gigabit Version 42200 7 3 4 Preset Click on the Download to save the actual settings except the local IP address of the unit to a file and store into the connected PC Click on the Upload to load the preset configuration to the connected unit note the IP address will not be loaded 28 ssd IP Address 10 10 80 67 Status I Configuration I System Device Network Preset Version Preset Download Upload ee Upload 8 Recommended Configuration Applications IPTV IPTV IPTV DVB mme Parameters SD 720P 10801 720P 10801 Video Rate Ctl ee jo je je Je e e et core fe qm n jm m m raa sr meme ee m eer OE fe ja jeje le je Null filter Fr o spts sprs SPTS MPTS MPTS MPTS mp Audio Channel Mode mono Stereo Stereo Stereo Stereo Stereo www antiktech com 29 MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder 9 Installation Fix the EN9200 or EN9400 chassis into the standard EIA 19 rack Insert the device into the fixed EN9200 or EN9400 chassis Caution the EN 9200 EN 9400 can be accommodated in the EN9200 or EN 9400 chassis only Inserting the device into other chassis or equipment may
19. lect one service from ASI input for transcoding IP select one service from IP input for transcoding User has to key in manually the Audio PID that need to be paired with the transcoded video Transcoder Audio PID the inputted audio can be independent from the video before transcoding Program List select the programs to remux Encoder Video 1 gt Click on Enter to select double click to cancel Service ID 1000 The program s will be marked with an asterisk once be selected Encoder Video ASI Input select the program s inputted via Service ID 2000 ASI input port IP Input select the program s inputted via IP Encoder Video Remux Program List input port Note this sub menu is displayed Service ID 3000 only when the IP I O is configured as full duplex mode Encoder Video 13 www antiktech com MANTIK technology 14 TS ID Output Bit Rate Remux Remux Source Output ASI Out Source Encoder 1 select the SPTS from encoder transcoder 1 Encoder 2 select the SPTS from encoder transcoder 2 Encoder 3 select the SPTS from encoder transcoder 3 Encoder 4 select the SPTS from encoder transcoder 4 TS ID key in the TSID of the newly generated MPTS valid range from 0 to 65535 decimal Output Bit Rate key in the bit rate of the newly generated MPTS valid range from 0 99999 Kb s Remux Enter Yes press Enter to remux Exit No press Exit to cancel Remux
20. ly when the TS IP operation mode is Full duplex mode To change the TS IP operation mode please refer to chapter 7 3 1 System Device 23 www antiktech com MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder kantel gy 24 ssd IP Address 10 10 80 67 ERE oe Encoder 1 Gigabit I Encoder 2 K Encoder 3 Encoder 4 Uni Multi Address 238 69 70 2 TS IP Uni Multi UDP Port 1234 Garn En Column FEC UDP Port 1236 Gigabit Out i Row FEC UDP Port 1238 Local Settings TS Clock Recovery Auto Remux Output Gigabit In Status Gigabit In Status Unlock Apply Gigabit Output Under full duplex operation mode the device supports single uni multicast output The default source for TS IP output is the built in remux To change the source please refer to chapter 7 2 4 Configuration Output Note the page below is displayed only when the TS IP operation mode is Full duplex mode To change the TS IP operation mode please refer to chapter 7 3 1 System Device ssd IP Address 10 10 80 67 Status l Configuration I System Encoder 1 Gigabit Out Encoder 2 3 Encoder 3 Encoder 4 Gigabit Out Switch Enable TS IP Protocol UDP aana m TS Pkts Per UDP 7 z Gigabit Out x Time To Live 255 Local Settings Type of Service Min Delay Remux Output Uni Multi Address 238 69 170 1 Uni Multi UDP Port 1234 Gigabit Out Status UDP Packets s 3610 Column FEC Pkts s 0 Row FEC Pkts s 0 Appl
21. nk you for purchasing the EN9200 EN9400 Quad Encoder Transcoder This User Manual is written for operators users of the EN9200 9400 to assist in installation and operation Please read this user manual carefully before installation and use of the device FOR YOUR SAFETY This equipment is provided with a protective earthing ground incorporated in the power cord The main plug shall only be inserted in a socket outlet provided with a protective earth contact Any interruption of the protective conductor inside or outside the device is likely to make the device dangerous Do not remove the covers of this equipment Hazardous voltages are present within this equipment and may be exposed if the covers are removed Only ANTIK Technology trained and approved service engineers are permitted to service this equipment The supplied AC power cable must be used to power the device If the power cord becomes damaged it must be replaced No operator serviceable parts inside Refer servicing to ANTIK Technology trained approved service engineers For the correct and safe use of the device it is essential that both operating and servicing personnel follow generally accepted safety procedures in addition to the safety precautions specified in this manual Whenever it is likely that safety protection is impaired the device must be made in operative and secured against unintended operation The appropriate servicing authority must be informed For example safety i
22. oder 2 E H 264 HDTV Encoder1 Encoder 3 Encoder 2 Encoder 4 E H 264 HDTV Encoder ssa Encoder 3 H 264 HDTV Encoder3 Encoder 4 H 264 HDTV Encoder4 ASI 7 2 4 Output The source for TS output via ASI and TS IP output interface can be configured independently User can select source among Encoder Remux ASI Input and TS IP Input available only under full duplex mode for each ssd IP Address 10 10 80 67 Status l Configuration System Encoder 1 Encoder 2 Output Encoder 3 Encoder 4 ASI Output Source Remux T TS IP TS IP Output Source Remux x Gigabit Out Local Settings Remux Output 26 7 3 System The system page gives all information of this device including device name serial number software version and so on User can implement the alarm switch configuration network settings TS IP operation mode and software upgrade under system page 7 3 1 Device Device name Check the name and the serial number of this device User can resign this product name at will the device name should be less than 24 characters The serial number is read only LED Alarm Switch Enable or disable the corresponding alarms by choose ON or OFF Gigabit Mode to switch the TS IP operation mode between Multiple Output and Full duplex Login ID amp Login Password User can modify the login ID and password for web control Factory Default click the button the device is reset to the factory paramete
23. oder transcoder Encoder bit rate must greater than the sum of video bit rate audio bit rate PSI 150Kbps buffering 100Kbps encoder error 150Kbps valid range from 300 to 99999Kb s Video Bit Rate set the video bit rate The setting is valid only when the Video Rate Ctl is CBR Video Max Bit Rate set the maximum video bit rate The setting is valid only when the Video Rate Ctl is VBR Video Min Bit Rate set the minimum video bit rate The setting is valid only when the Video Rate Ctl is VBR GOP Size set the GOP size valid range from 0 63 Note the bigger the value better the compression ratio for video but longer the latency of encoding GOP Structure set the structure of GOP Optional structure is listed in the drop down list GOP Adaptive switching on the GOP adaptive the GOP size and structure may variable according to the dynamic video scenes Input Video Adaptive the setting is valid only for encoding mode ON the encoder will detect the input video format automatically when the input video format changes the encoder will follow the change OFF the encoder must be assigned an input video format manually when the input video format changes the encoder will not follow the change user has to re assign the correct input video format manually Audio SDI EMB select the group of embedded audio from input SDI signal Sound Mode set the audio in stereo or mono NOTE only Left audio channel will be encoded when Mono mode is on
24. rface 4 HDMI input interface 4 SDI input interface 6 Operation instructions using EN9200 EN9400 programmer NOTE The EN9200 EN9400 Programmer is a universal programmer unit for ANTIK s EN product family EN9200 EN9400 programmer is a standalone product and not included in the package of EN9200 9400 please contact your sales agency for more information 6 Overview of the Menu Users are advised to restore factory setting of the machine before the first time using it Because of machine s too many functions users are advised not to change those temporarily useless parameters in order to avoid unnecessary fault After power on the Local IP address will be shown on the LCD of EN9200 EN9400 programmer User can press ENTER to get into the main menu Main Menu 1 2 3 4 5 6 Status show the status of the device Encode Configure and monitor parameters of encoding transcoding Remux Configure and monitor parameters of TS re multiplexing procedure Output Configure and monitor parameters of TS output System Configure the local settings of the device 6 TS IP Configure the settings for the TS IP interface 6 2 Description of menu Main Menu Sub Menu Description Factory Default Value ASI Input Bit rate Display the input ASI signal bit rate rr TS IP Input Bit Rate Display the TSoverlP input bit rate Encoder 1 Bit Rate Display encoder transcoder 1 bit rat
25. rs Note the IP address of the device is not reset to the factory setting While press the button A8 IP Reset via the front panel the IP address is reset to the factory setting 10 10 70 48 Device Reboot User can reboot this device by clicking the button Device Reboot ssd IP Address 10 10 80 67 Status f Configuration System Device Network Device Information Version Preset Device Label DMM 2411EC Serial Number gTO1YF3270053 Front Panel LED Alarm Switch LED ASI Alarm ON LED TS IP Alarm OFF LED Encoder 1 Alarm ON LED Encoder 2 Alarm ON LED Encoder 3 Alarm ON LED Encoder 4 Alarm ON Gigabit Mode Gigabit Mode Multiple Output x Login Login ID Login Password Cancel Factory Default Device Reboot 7 3 2 Network The network settings for the device can be found and configured under the page below The trap IP address SNMP Server Address should be set the IP address of the SNMP management server if used to which the SNMP Trap information generated by the device will be sent 27 www antiktech com MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder technology ssd IP Address 10 10 80 67 EDE en Device Network Network Version Preset Local Settings IP Address 10 10 80 67 Subnet Mask 255 255 255 LO Gateway 10 10 Z0 1 MAC Address 00 06 14 32 9d 5c Remote Setting Trap IP Address 10 10 90 45 Apply 7 3 3 Vers
26. s likely to be impaired if the device fails to perform the intended measurements or shows visible damage WARNINGS e The mounting environment should be relatively dust free free of excessive vibration and the ambient temperature between 0 C to 40 C Relative humidity of 20 to 80 non condensed is recommended e Avoid direct contact with water e Never place the equipment in direct sunlight The outside of the equipment may be cleaned using a lightly dampened cloth Do not use any cleaning liquids containing alcohol methylated spirit or ammonia etc e For continued protection against fire hazard replace line fused only with same type Air intake for cooling is achieved via holes at the side of the device and the fans inside The air flow should not be obstructed Therefore the device has to be placed on a flat surface leaving some space at the sides of the device e When in operation the internal temperature should not exceed the limit of 70 C 3 www antiktech com MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder tet hm l gy Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder 1 Overview EN9200 EN9400 is a series of four channel H 264 HD SD amp MPEG 2 SD real time encoder Transcoder This blade type design integrates 4 independent encoders transcoders 1 reMultiplexer 1 ASI in 1 ASI out 1 Gigabit GbE TS IP port and 4x CVBS or 4x HD SDI or 4x HDMI AV input por
27. s to rain or moisture To avoid explosion danger do not dispose of batteries in an open fire CE MARK FOR EUROPEAN HARMONISED STANDARDS The CE mark which is attached to these products means it conforms to EMC Directive 89 336 EEC and Low Voltage Directive 73 23 EEC IMPORTANT INFORMATION Please retain the original packaging should it be necessary at some stage to return the unit Disposal of Old Electrical and Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local Civic Office your household waste disposal service or the shop where you purchased the product 1 www antiktech com MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder be on holo ay COPYRIGHTS Television programs movies video tapes discs and other mater
28. showed asking for login user and password After login the device can be operated The default user name and password are respectively root and 12345 The username and password can be changed by user via EN9200 9400 programmer unit or via submenu under the system page If the username and password are forgotten user have to use a EN9200 9400 to retrieve or set a new one 18 Brighten Your Digital View 7 1 Status Via the status page user can have an overview of the current status of the connected EN9200 EN9400 H 264 HDTV Encoder IP Address 10 10 80 68 Status Configuration System Status Status Output Status Encoder i Valid Bit Rate Mb s 05 654576 Total Bit Rate Mb s 05 654576 Service Narne H 264 HDTV En Encoder 2 Valid Bit Rate Mb s 02 481600 Total Bit Rate Mb s 02 481600 Service Name H 264 HDTV En Encoder 3 Valid Bit Rate Mb s 02 601600 Total Bit Rate Mb s 02 601600 Service Name H 264 HDTV Ed Encoder 4 Valid Bit Rate Mb s 05 015792 Total Bit Rate Mb s 05 015792 Service Name H 264 HDTV En ASI Valid Bit Rate Mb s 16 170448 Total Bit Rate Mb s 48 008344 TS IP Valid Bit Rate Mb s 16 170448 Total Bit Rate Mb s 48 008344 Input 5tatus ASI Input Valid Bit Rate Mb s 00 000000 Total Bit Rate Mb s o0 000000 Video Input Format 8 Videol Input Format 1920x1080i 23 8 Video Input Format 1920x1080i 25 8
29. t Login ID press Enter and key in the login Edit Login ID root www antiktech com 15 MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder technology ID for WEB management l Edit Login Password press Enter and key in Edit Login Password WEB Login Password the password for WEB management 12345 LED Alarm Switch ASI Alarm switch on off the alarm for ASI input TS IP Alarm switch on off the alarm for TS IP input ASI Alarm OFF Encoder1 Alarm switch on off the alarm for TS IP Alarm OFF Sn encoder transcoder 1 Encoder Alarm ON Encoder2 Alarm switch on off the alarm for Encoder2 Alarm ON encoder transcoder 2 Encoder3 Alarm ON Encoder3 Alarm switch on off the alarm for Encoder4 Alarm ON encoder transcoder 3 Encoder4 Alarm switch on off the alarm for encoder transcoder 4 Gigabit Mode Multiple Output the IP I O is configured as multiple uni multicast output mode which delivers up to five streams over IP There are four stuffed or un stuffed SPTS lower bit rate but less PCR accurate than normal SPTS from MEM l Gigabit Mode Multiple Gigabit Mode local encoders and one MPTS from internal B utpu reMultiplexer over the IP with different Unicast E or Multicast IP addresses Full Duplex the IP I O is configured as full duplex mode which allows only one MPTS or SPTS over IP input and output in uni multicast at the same time Uni Multi IP Address set th
30. t PMT PID set PMT PID valid range Output PMT PID 43 from 32 to 8190 decimal Output Video PID set Video PID valid range l Output Video PID 4001 from 32 to 8190 decimal Output Audio PID set audio PID valid range l Output AudioPID 4002 from 32 to 8190 decimal Output Service PID set Service PID valid l Output Service PID 4000 from 32 to 8190 decimal Output PCR PID set PCR PID valid range Output PCR PID 8004 from 32 to 8190 decimal Output Service Name Output Service Name set the service name H 264 HDTV Encoder Advanced Settings 12 Service Provider Name set the service provider name The service name should be less than 24 characters Null Filter On filter away the null packages Off the service is stuffed with null packages Null Filter On Note Null packet is essential for DVB applications don t remove them Encode Mode H 264 the selected encoder transcoder is set to H 264 SD HD Encoder MPEG 2 the selected encoder transcoder is set to MPEG 2 SD Encoder MPEG 2 to H264 the selected encoder transcoder is set to MPEG 2 to H 264 Encode Mode Vanna H264 to H264 the selected encoder transcoder is set to H 264 to H 264 Transcoder H264 to MPEG 2 the selected encoder transcoder is set to H 264 to MPEG 2 SD Transcoder MPEG 2 to MPEG 2 the selected encoder transcoder is set to MPEG 2 to MPEG 2 SD Transcoder Input the menu is active only when Transcoder mode is selected marema ASI se
31. t output bit rate in an allocated bandwidth to avoid potential overflow Status Configuration System Encoder 1 Encoder 2 Encoder 3 Encoder 4 TS IP Remux Output 7 2 2 TS IP Work Mode Video Settings Video Rate Ctl Video Bit Rate kb s Video Max Bit Rate kb s GOP Size GOP Adaptive Output Horizontal Frame Format Image Settings Brightness Control Saturation Control Audio Settings Audio Channel Mode Audio Bit Rate Advanced Settings Output PMT PID Output Audio PID Output PCR PID Null Filter H264 CBR 2000 6000 oe ON 720 Interlaced Stereo 128kbps 1003 1002 2001 ON ssd IP Address 10 10 80 67 Encoder Transcoder 1 Encoder Bit Rate kb s Input Video Format Aspect Ratio Video Min Bit Rate kb s GOP Structrue Output Video Format Output Vertical Input Format Adaptive Contrast Control Hue Control Audio Format Audio Level Output Video PID Output Service ID Output Service Name Service Provider Name 6 00 720x5761i 25 16 9 0 IBBBP Auto Settings 376 OFF MPEG1 Layer2 n dB 1001 1000 H 264 HDTV Encod ANTIK Technology Apply Cancel All models provide two TS IP operation modes The first is Full Duplex which allows one MPTS or 21 www antiktech com MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder Cie ohh o lo uv SPTS inputted to make up a new MPTS wit
32. tput Video Format Auto Settings Horizontal 1280 Vertical 720 Frame Format Progressive Saturation Control O Hue Control 0 11 www antiktech com MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder technolo range 0 255 Brightness Control set the brightness of the Brightness Control 0 picture valid range 100 100 Contrast Control set the contrast of the Contrast Control 0 picture valid range 100 100 Audio Format Audio Format MPEG1 MPEG1 Layer2 set the audio compression Layer2 format MPEG 1 Layer Il Audio Bit Rate 128k bps 160k bps 192k bps Audio Bit Rate 64 Kbps 224k bps 256k bps 320k bps 384k bps 32k bps 48k bps 56k bps 64k bps 80k bps 96k bps 112k bps Audio Channel Mode Audio Channel Mode l l Stereo set stereo mode Stereo Audio Settings l Mono set mono mode NOTE only Left audio channel will be encoded Audio Level Audio1 Level OdB 16dB 17dB set the gain of output volume Mute mute the output audio Audio SDI EMB the menu is displayed on Audio SDI EMB EMB1 EN9200 EN9400 EMB1 EMB2 EMB3 EMB4 select the group of embedded audio from input SDI signal Encoder Bit Rate set the output bit rate of the selected encoder transcoder Encoder bit rate Encoder Bit Rate Encoder Bit Rate must greater than the sum of video bit rate 13700Kb s audio bit rate PSI 150Kbps buffering 100Kbps encoder error 150Kbps Outpu
33. ts as factory hardware options by order New MPTS could be generated with the built in reMultiplexer from any combination of services among ASI in TS IP in and the local encoders All models support transcoding function see below They accept an MPTS and transcode up to 4 TS inside and the final output is formed as an MPTS and or 4 un stuffed SPTS The device is operated locally either via a EN9200 EN9400 programmer unit or with the implemented web server via a web browser A SNMP agent with the corresponding MIB is built in for the integration in a network management system The device is controlled via a separate LAN connection which has a separate IP address thus the device can also be accessed from a distance EN 9200 EN 9400 series modules can be fitted into programmer 19 x 4RU 8 slots and Dual power supplies or 19x 1RU 2 slots single power supply chassis 2 Features gt Compliant with H 264 AVC Baseline Main amp High Profile L4 0 or less amp MPEG 2 MP ML gt 4independent AV inputs SDI HDMI CVBS Note see Chapter 4 Order Information ndependent Encoding Transcoding mode control gt Internal reMultiplexer new MPT S is made up from ASI in TS IP in amp Local Encoders gt MPTS remultiplexed and 4 local un stuffed SPTS available over IP gt Video Input Resolution 10801 720p 576i 480i note CVBS models support SD only see Chapter 4 Order Information Minimum Video Bit Rate 500Kb s Standard PAL or NT
34. y Cancel Local Settings Set the parameters for the TS IP output port Note the Gateway MAC address means the MAC address of the gateway under which the device is connected This parameter has to be configured when the TS IP output is delivered to a destination that is not located under the same subnet ssd IP Address 10 10 80 67 Status i Configuration System Encoder 1 Gigabit Local Settings Encoder 2 g g Encoder 3 Encoder 4 Gigabit Address 10 10 80 60 TS IP Gigabit Subnet Mask 255 255 255 o Gigabit In Gigabit MAC Address 00 06 f4 32 9d Sd Gigabit Out Gateway IP Address 10 10 30 A Local Settings Gateway MAC Address P cH br cH Fo i Remux Output Cancel 7 2 3 Remux The device supports remux the 4 SPTS generated locally with the service s carried by the transport stream inputted via ASI In or TS IP In available only under full duplex mode The Output Bit Rate is the bit rate of the remux output the value has to be equal or greater than the total bit rate of the selected services 25 www antiktech com MANTIK EN9200 EN9400 Quad H 264 HD SD MPEG 2 SD Encoder amp Transcoder Le c hi no lo gv ssd IP Address 10 10 80 67 IT ER Encoder 1 Encoder 2 aw Encoder 3 Encoder 4 Remux Source ASI Output Bit Rate kb s 38000 TS IP TS ID 16 Gigabit Out l neal Seins Input TS Total No of Service 6 Output TS Total No of Service 4 Remux Encoder 1 S Encoder 1 T Output Enc
Download Pdf Manuals
Related Search