Manual
Contents
1. 169 or EN 379 Rain steam humidity Select a clean environment to use your product degree of pollution lt 3 on the even place and put the machine at least one meter from the part to be welded Electric_shock This unit has to be used on a single phase power supply with 3 wires with neutral connected to the earth Do not touch the parts under voltage Check that the supply system is well adapted to the unit Drop Do not carry it over the people or things and do not drop it Do not use the unit to thaw tubing In TIG welding manipulate the gas bottle carefully Indeed there are risks if the bottle or the bottle valve are damaged Mise jour 22 03 06 Version S77 N nomenclature 72123 Protect Burns Wear protective or fire proof clothing overalls jeans Use some welder gloves and a fire proof apron Protect the others by installing non flammable protection wall or prevent the others to not look at the arc and to keep a sufficient distance Fire risks Suppress all flammable products from the working area Do not works near flammable gas Smokes Do not inhale gas or welding smokes use adapted extractors2. 2003 Low Voltage Directive and EN 50199 Electromagnetic compatibility Directive GYSMI TIG 143 HF DV POWER SUPPLY STARTING e This product is delivered without plug You can connect it either on 115V earth or 230V earth 16A 230V 32A 115V e This product is protected against over voltage or under voltage which are the result of the normal fluctuation of the mains supply or of a power plant e Your unit has a small switch on the front face and you have 3 modes of welding respectively y TIG TSL MMA Electrode TIG HF gt Connect the trigger plug The TIG 143 DV HF without accessories is delivered with the connector of command of the trigger as indicated on the following diagram Connect wires of contact normally opened on the studs Il ELECTRODES WELDING from 10 A to 120 A e Please follow standard rules for welding e After welding leave the machine connected for cooling e Thermal protection the indicator light comes on and cooling time is about 5 min Your unit is equipped with 3 special Inverter functions Hot START gives arcing overcurrent about 25 more than the displayed setting Arc force provides an overcurrent about 15 more than the setting to avoid sticking when the electrode enters the bath and Anti sticking lets you separate the electrode easily without reddening in case it sticks Mise a jour 22 03 06 Version S77 N nomenclature 72123 MI WELDING PARAMETERS lectrode dia
3. X MEANING OF INDICATIONS AND MARKINGS A Amps l1 eff Maximum network effective power supply V Volts U1 Network voltage Hz Hertz EN 60 974 1 The device complies with EN60974 1 standard relative to welding units Electrode welding MMA a CO Single phase inverter converter rectifier Tungsten Inert gas Tig X X operating factor at 45 60 and 100 Protection against enlarged risks of Ph fa fa a 2 corresponding currents E The welding current is U wv 7 U2 conventional voltages in ea re de ers a ee Pu alternative in Tig AC Hv pov corresponding load Eo Welding direct current 21 Protected against rain and Complies with GOST Norms against fingers access to dangerous Russia parts Rated no load voltage i Single phase power supply 50 iia LL or 60Hz The electric arc produces dangerous rays for eyes and skin protect yourself limax Maximum mains current effective value Caution welding can produce fire or explosion CE The device complies with European Directive Caution Read the user manual Separate collection required Do not throw in a domestic dustbin Declaration of conformity The equipment presented in this user manual complies with EEC Directives 83 336 Electromagnetic compatibility and 73 23 low voltage for professional or experienced use This conformity is established in compliance with EN 60974 1 and A1 A2 of
4. d the unit does not supply any current check the following points A Both indicator lights are on Wait for the end of the cooling period B The on off switch is on 1 nothing s matter If when you put your hand on the outer casing you feel tingling while the machine is on this means that the earthing is defective Check the extension cable the plug and the earth to your installation 1X MAINTENANCE The maintenance must be done by a professional Disconnect the generator and wait until the ventilator stopped before working on the unit Inside the device voltages and current are dangerous Regularly remove the steel cover and blow off the dust with compressed air Check the electrical connections with an insulated tool X ADVICE Respect welding polarities and currents indicated on the electrode packaging The arc welding can be dangerous and leads serious injury may fatal Remove the electrode from the electrode holder when you do not use it Leave the inlets free to allow in out air circulation Remove the dust from the device regularly with an air gun after disconnection Control regularly the state of the mains cable Change it if damaged XI SECURITY yourself and protect the others Take protections against Do not use this unit near people using Pacemaker arc emissions Protect yourself thanks to an electronic welding helmet in compliance with EN 175 supply with filters in compliance with EN
5. meter mm min f _Tavg f Imar Power generating set 4 5 KVA 5 5 KVA IV WELDING TIG HF de 10 A 140 A 15 ale aes an Adjustable welding current m A ne Li Frequency adjustment of the pulsation position off TIG not pulsed Arc slope down adjustment And position mode spot e When you press on the tigger a H F signal allows remote starting between the electrode and the part to be welded use under gas Argon e You can regulate the slope down of the arc from O to 10 seconds and post gas from 3 to 5 seconds V TSL TIG WELDING from 10 A to 140 A e Itis system of striking device without high frequency in TIG gt T Touch touch the electrode on the part to be welded gt S Switch press on the trigger gt L Lift raise the electrode before a lapse of time of two seconds e The adjustments of post gas and the slope down of arc are the same ones as above VI PULSED TIG WELDING e In order to weld in this type of welding you must adjust the pulsed potentiometer between 0 8 and 2 8 Hz 0 8Hz for a maximum timing between each pulsation and 2 8 Hz for a minimum timing between each pulsation VII MODE SPOT in TIG HF or TSL e This type of product is able to do spot welding potentiometer switch pulsed in position off and potentiometer switch Down slope in spot position You can work quickly with this mode VIH TROUBLES SHOOTING If when you are ready to wel
Download Pdf Manuals
Related Search
Manual manual manualslib manual car manual timesheet manual transmission manuale digitale manually meaning manual wheelchair manual arts high school manually update your device drivers windows manual labor manual definition manual for courts martial manual muscle testing manual muscle testing grades manually register devices with autopilot manual keyboard manual blood pressure cuff manualidades manual lawn mower manual transfer switch manual transmission cars for sale manual therapy cpt code manual libs manual autopilot enrollment