EFG750X-A Installation, Care and Use Manual
Contents
1. Instruction Manual Dear Customer If you follow the recommendations con tained in this Instruction Manual your appliance will give you constant high performance and will remain efficient for many years to come CONTENTS RECOMMENDATIONS AND SUGGESTIONS CHARACTERISTICS INSTALLATION USE MAINTENANCE o IN Oo IA I RECOMMENDATIONS AND SUGGESTIONS INSTALLATION e The manufacturer will not be held liable for any damages resulting from incorrect or improper installation e The minimum safety distance between the cooker top and the extractor hood is 650 mm Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood e For Class 1 appliances check that the domestic power supply guarantees adequate earthing Connect the extractor to the exhaust flue through a pipe of mini mum diameter 120 mm The route of the flue must be as short as possible e Do not connect the extractor hood to exhaust ducts carrying com bustion fumes boilers fireplaces etc e Ifthe extractor is used in conjunction with non electrical applian ces e g gas burning appliances a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas The kitchen must have an opening communicating directly with the open air in order to guarantee the entry of clean air USE e The extractor hood has been designed exclusiv2. LM V L Light Switches the lighting system on and off M _ Motor Switches the extractor motor on and off Vv Speed Sets the operating speed of the extractor 1 Low speed used for a continuous and silent air change in the presence of light cooking vapour 2 Medium speed suitable for most operating conditions given the optimum treated air flow noise level ratio 3 Maximum speed used for eliminating the highest cooking vapour emission including long periods MAINTENANCE Grease filters CLEANING METAL SELF SUPPORTING GREASE FILTERS e The filters must be cleaned every two months of operation or more frequently with heavy usage and can be washed in a dishwasher e Remove the filters one at a time after disconnecting the relative fastening elements e Wash the filters taking care not to bend them Allow them to dry before refit ting e When refitting the filters make sure that the handle is visible on the outside Odour filters Recirculation version REPLACING ACTIVATED CHARCOAL FILTERS e These filters are not washable and can not be regenerated and must be repla ced approximately every four months of operation or more frequently with heavy usage e Remove the grease filters e Remove the saturated activated carbon filters by releasing the fixing hooks e Fit the new filters by hooking them into their seating e Replace the grease filters LIGHT REPLACEMENT 40 W incandesce
3. ely for domestic use to eliminate kitchen smells e Never use the hood for purposes other than for which it has ben designed e Never leave high naked flames under the hood when it is in ope ration Adjust the flame intensity to direct it onto the bottom of the pan only making sure that it does not engulf the sides Deep fat fryers must be continuously monitored during use ove rheated oil can burst into flames The hood should not be used by children or persons not instructed in its correct use MAINTENANCE e Switch off or unplug the appliance from the mains supply before carrying out any maintenance work e Clean and or replace the Filters after the specified time period e Clean the hood using a damp cloth and a neutral liquid deter gent CHARACTERISTICS Dimensions Hood Type 52 70 L1 522 702 Components Ref Q ty Product Components 9 1 1 Hood Body complete with Controls Light E Filters 9 4 Reducer Flange 150 120 mm Q ty Documentation 1 Instruction Manual INSTALLATION Drilling the Support surface and Fitting the Hood Make a rectangular opening on the base of the hanging unit leaving a minimum of 13 mm from the outer edges Hood Type 52 70 L1 497 677 SNAP ON FITTING For hoods with snap on side supports only set up for a support panel thickness of between 15 mm and 30 mm e Insert the hood until the side support
4. nt light e Remove the metal grease filters or open the filter retaining grill e Unscrews the bulbs and replace them with new ones having the same characteristi cs e Replace the metal grease filters or close the filter retaining grill Ce Dir 89 336 CEE 73 23 CEE 93 68 CEE The symbol E on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 436003033_01 051212
5. s snap into place e Lock in position by tightening the screws Vf from underneath the hood SCREW FITTING For hoods without snap on side supports only e Fix the hood to the hanging unit using the screws 12f 3 5x16 self threading provided Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version connect the hood to the chimney using either a flexible or rigid pipe 120 or 150 mm the choice of which is left to the installer e To install a y 120 mm air exhaust con nection insert the reducer flange 9 on the hood body outlet e Fix the pipe in position using sufficient pipe clamps not supplied e Remove any activated charcoal filters RECIRCULATION VERSION AIR OUTLET e Cuta hole 120 mm in the wall unit over the hood e Insert the reducer flange 9 on the hood body outlet e Connect the hood body outlet to the top part of the wall unit using a rigid or flexible pipe 120 mm to be selected by the installer e Fix the pipe in position using sufficient pipe clamps not supplied e Ensure that the activated charcoal filters have been inserted ELECTRICAL CONNECTION e Connect the hood to the mains through a two pole switch having a contact gap of at least 3 mm e When opening the sliding carriage for the first time after installing the hood pull it out briskly until it clicks USE Control Panel ra eu 123 W D U
Download Pdf Manuals
Related Search