Home

to your file

1. 109 PLUMBING SYSTEM EEE ZUL IMPORTANT In order for the 120 VAC tank heaters to be in operation the recreation vehicle MUST be hooked up to shore power or under generator power Ifthe recreation vehicle is not operating on shore power or generator power only the 12VDC heaters will operate This can result in the tanks freezing The red light on the command center tank switch does not necessarily indicate that ALL heaters are operating it is a warning that the heater circuit is ON The tank heater switch should be turned ON When liquid is present in the holding tanks and the outside temperature approaches and maintains freezing conditions 35 F 2 C or colder The tank heater switch should be turned OFF When there is NO liquid present tanks are empty When dumping the black and gray holding tanks and the drain pipes When fresh water tank and supply lines are empty or being drained for storage When the recreation vehicle is connected to city sewer and the gate valves are open NOTE Free draining is never recommended especially in cold weather use When ambient temperatures rise and remain above freezing No maintenance on the heaters is required only a periodic inspection for loose wires damage etc For additional detailed information refer to the tank heater manufacturer s user guide TOILET The toilet is efficient and easy
2. Only seats equipped with seat belts are to be occupied while the vehicle is in motion While traveling do not occupy beds or any seats that do not have seat belts Be sure to lock all doors before driving Locking the doors and using the provided seat belts will minimize the risk of injury or ejection in an accident If you are pregnant consult your health care professional for advice on seat belt use Seat belts are installed in your motor home to protect the driver and passengers Always use seat belts In an accident injury to the driver and passengers may be reduced 1f seat belts are properly used The booth dinette hide a bed sofa and easy bed sofa have two point lap seat belts installed Seat belts should be used in all seating positions Maintenance and inspection of seat belts The webbing used in seat belts may be cleaned with a mild soap or detergent solution Allow the belts to dry in the shade and do not allow them to retract until fully dry Do not try to bleach or re dye the belts The resulting color may rub off and the webbing strength could be affected Regularly check the seat belt buckles and release mechanisms for positive action and check automatic locking retractors for positive engagement If the seat belt webbing shows obvious cuts protruding broken fibers or severe fading which indicates weakening by exposure to sunlight the entire seat belt assembly should be r
3. Rotate the small attenuator knob counter clockwise until the last illuminated LED light flickers 121 ELECTRONICS ua Rotate the antenna knob to illuminate the last flickering LED Refer to your TV or converter box manual for information on how to scan for available channels Refer to the HDTV manufacturer s manual for detailed operating and safety information EXTERIOR TELEVISION IF SO EQUIPPED The exterior television is located on the curbside of the unit You can access the television by opening the exterior cargo door to the stationary open position Refer to the individual component manufacturer s information located in the Warranty Packet for detailed operating instructions 122 INTERIOR L CLEANING THE INTERIOR To keep the value of your recreation vehicle perform regular maintenance using the proper materials and procedures Using the wrong cleaner may result in damage to the surfaces in your vehicle Check with the manufacturer s information for the recommended cleaning agent If in doubt check to see 1f the cleaner will cause damage by testing a small area out of sight or contact your dealer for assistance Do not use flammable liquids or sprays to clean the recreation vehicle FURNITURE UPHOLSTERY To retain the value of your motor home maintain the furniture upholstery carefully and keep the interior clean Vacuum the furniture regularly using a soft brush atta
4. Rand McNally Camp Guide Good Sam Camp Guide KOA Kampgrounds Camp Guide and various other publications Some fuel stations also have dump stations Please contact your RV dealer for assistance in the purchase and installation of a sewer hose and or sewer hose extension if needed Brack TANK FLusH IF So EouIPPED The black tank flush is also called a no fuss flush The black tank flush inlet is located on the utility center panel Attach a garden hose connected to a pressurized fresh water source to the black tank flush inlet The water goes directly into the black water holding tank where there is a sprayer connection This allows you to rinse the black water holding tank by removing debris and preventing accumulation There is a check valve incorporated in the plumbing lines to prevent back flow Flush the black water tank each time the grey and black water holding tanks are dumped or as needed Refer to Macerator Pump System section 1 Dump the black water tank see Gray Tank Drain amp Black Tank Drain and leave the black tank drain valve open Connect a garden hose from the water supply source to the black tank flush 3 With the water source turned ON flush the black water holding tank until the water running out of the black tank drain valve is clear not discolored or cloudy 108 PLUMBING SYSTEM oo 4 Disconnect the garden hose and close the black tank drain valve Fasten the sewer hose
5. 1 Turn off the water heater 2 Turn off the cold water supply line 3 Open a faucet in the motor home 4 Pull out the handle of the pressure relief P amp T valve and allow water to flow from the valve until it stops 5 Release the handle on the P amp T valve it should snap closed Close the faucet and turn on the cold water supply As the tank fills the air pocket will develop Repeat this procedure as often as needed to reduce the frequency of the weeping P amp T valve Maintenance Do not allow the burner to burn with a yellow flame or continue to operate the water heater with an improper burner flame Periodically inspect the water heater vent for soot Soot is a sign of incomplete combustion and must be corrected before operating the water heater This is your visual warning that the water heater is operating in an unsafe manner If soot is present immediately shut the unit down and contact your dealer or a qualified service agency Periodically inspect the vent for obstructions Do not terminate the vent on your water heater inside of add on rooms screen porches or patios Doing so will result in products of combustion being vented into the rooms or occupied areas Draining and winterization If the recreation vehicle is to be stored over the winter months the water heater must be drained to prevent damage from freezing Damage to the water heater caused by freezing is not warrantable It is recommended the water he
6. N NOTE A road test by the dealer should be included as part of the pre delivery inspection The dealer can check for and correct any steering problems before you take delivery After this road test has been completed front end alignment and or vibrations will not be covered as part of the new vehicle limited warranty 45 VEHICLE OPERATION WHEEL Lucs WHEEL LINERS Failure to maintain proper torque of the wheel lug nuts could lead to separation of the tire and wheel while driving possibly resulting in property damage or personal injury Check and tighten the wheel lug nuts regularly to make sure they did not loosen during travel Refer to your Chassis Guide for Torque recommendations Failure to tighten and maintain wheel lug nuts to the proper torque specification could allow the wheels to come off while the motor home is in motion and could result in serious injury in the event of a collision or loss of vehicle control Torque is the amount of rotating force applied to a fastener such as a lug nut Proper torque of lug nuts can only be achieved by using a properly calibrated torque wrench and socket Do not use a 4 way socket or any other type of wrench that does not measure the actual pressure applied to the lug nut N N NOTE The proper method of tightening wheel lug nuts is with a torque wrench not with an impact wrench or by hand Because of the importance of having proper torque on the wheel
7. You or your dealer must make a confirmed appointment a minimum of 60 days prior to dropping off your RV at the Jayco Factory Service Center The holding tanks must be emptied and rinsed We have a dumping station available for customer use The propane system and all electrical systems must be shut down and turned off We are not responsible for discharged batteries or propane tanks During the appropriate season please ensure your RV is winterized Unless prior approval has been obtained from the Jayco Factory Service Center all personal items must be removed from the area where you are requesting service repair and the refrigerator emptied We are not responsible for loss of food items All transportation costs are the responsibility of the owner You may need to arrange for alternative accommodations for some types of repairs Please be prepared accordingly Jayco Customer Service occasionally utilizes local independent repair facilities Your RV may be referred to or repaired by one of these local repair facilities Parts amp ACCESSORIES Contact your independent Jayco dealer for assistance in obtaining replacement parts or accessories Jayco does not sell parts retail direct or to non authorized dealers If the original part is no longer available Jayco makes every effort to provide an appropriate substitute MOTORI ZED LIMITED WARRANTY WHAT AND WHO IS COVERE
8. Convection Microwave if so equipped For details on operation cleaning and safety information refer to the manufacturer s user guide included in the Warranty Packet or visit the manufacturer s website The convection microwave bridges the gap between microwaving your food and conventional cooking Make sure there is sufficient 120 volt power available before operating the convection microwave refer to Sec 6 Electrical Systems Calculating electrical load Microwave Oven Use For list of preset programs see the Quick Reference Guide provided with your model General Cleaning IMPORTANT Before cleaning make sure all controls are off and the microwave oven is cool Always follow label instructions on cleaning products To avoid damage to the microwave oven caused by arcing due to soil buildup keep cavity microwave inlet cover cooking rack supports and area where the door touches the frame clean Clean with mild soap water and a soft cloth or sponge or as indicated below Grease filters mild soap and water or dishwasher Door and exterior mild soap and water or glass cleaner applied to paper towel Control panel sponge or soft cloth and water Stainless steel on some models mild soap and water then rinse with clean water and dry with soft cloth or use stainless steel cleaner Turntable mild soap and water or dishwasher Rack s mild soap water and washcloth Dis
9. There are three basic types of public scales Each type of scale involves a different procedure in weighing the motor home Your motor home must remain as level as possible on the scale even if an axle is not physically on the scale To obtain the side to side weights make sure there is enough space on either side of the scale to accommodate the motor home being partially off the scale If a boat trailer or other vehicle is being towed it should be weighed separately This weight should be combined with the motor home s Gross Vehicle Weight GVW to ensure the total combined weight does not exceed the GCWR Once actual weights are obtained it is now possible to compare them to the Weight Information Label weight ratings to ensure you are below the posted minimum ratings If there is a difference in the weights on one side of the vehicle as compared to weights on the other side components tires wheels brakes springs etc on the heavier side may be overloaded although the total axle load is within the GAWR It is important to redistribute the load to avoid component failure as well as to improve the handling characteristics of the vehicle 35 VEHICLE OPERATION MARX Ko Dump the gray and black water holding tanks before traveling to avoid carrying unnecessary weight Traveling with the tanks full can affect your fuel consumption and depending on the location of the tanks can affect your vehicle handling charact
10. UsinGc THe REAR HITCH The motor home 15 designed primarily as a recreation vehicle Any towing will affect vehicle handling durability and fuel economy Exceeding any of the listed weight ratings will result in unacceptable overall vehicle performance Your safety and satisfaction require proper use of correct equipment The factory installed towing hitch on this vehicle is capable of pulling 5 000 Ibs of load maximum however the vertical tongue weight will vary according to the towed vehicle A hitch bar of appropriate strength and steel should be selected to match the towing receptor Always use safety chains between the motor home and the towed trailer or vehicle Cross the chains under the tongue and allow for slack when turning corners Connect the safety chains to the vehicle frame or hook retainers Never attach the safety chains to the bumper Before descending a steep or long grade when towing a trailer or vehicle reduce speed and shift the motor home into a lower gear to control vehicle speed Avoid frequent or prolonged brake application which can cause overheating or brake failure By definition the GCWR is the maximum total weight rating allowed for a vehicle and any attachment such as a trailer or towed vehicle To determine the total allowable weight for a towed item subtract the GVWR from the GCWR Do not remove the following label AWARNING YOUR MOTORHOME CHASSIS BRAKING SYSTEM 15 RATED FOR OPERATION AT GVW
11. The Load Center contains 12 VDC fuses and 120VAC circuit breakers for almost all of the electrical appliances and circuits in the RV The 120V Main Breaker if so equipped is located in this panel and will turn off all 120 volt power to the recreation vehicle The Load Center is a hinged plastic panel typically attached to a cabinet face in the main living area Locations will vary by model Refer to the diagram inside the Load Center for specific fuse assignments Most load centers contain the same components but they may be positioned differently Not all load centers will include a main breaker Typical Load Center Exterior 50A Load Center Panel w 120 volt Panel Main breaker APPROXIMATE ELECTRICAL LOAD RATINGS 12 Volt System 68 ELECTRICAL SYSTEM SSE Porch Light 1 5 AMPS 10 0 AMPS 5 0 AMPS Refrigerator 3 0 AMPS Shower Light 1 4 AMPS Step Cover 10 0 AMPS TV Plate Antenna Booster 1 0 AMP Vanity Light 4 2 AMPS Water Heater 6 0 AMPS Water Pump 7 0 AMPS Momentary Load 12 Volts Labeled watts divided by 12 Power consumed in AMPS 120 Volt System 120 Volts Labeled watts divided by 120 Power consumed in AMPS GENERATOR The factory installed generator will produce 120 volt AC power for use when camping in areas where shore power is unavailable 120 volt power from the generator is output to the AC distribution center by way of a factory installed automatic transfer switch In the default mode the auto
12. The upper portion of the label is the federally required OCCC label that indicates the total combined weight value of occupants and cargo that may be placed in or on your motor home as it was manufactured and weighed before leaving the factory This label also indicates the number of safety seat belts that have been installed at the factory Additions or other changes made to the motor home after it left the factory will affect reduce the OCCC Federal OCCC and voluntary weight labels The lower portion of the label is provided voluntarily and indicates the weight value of the motor home as it was manufactured and weighed before leaving the factory This label also indicates the GCWR of the completed motor home Federal OCCC and voluntary weight labels The motor home towing and braking label is located on the rear bumper above the hitch receiver Be sure to read and follow the guidelines and information stated on this label WARNING YOUR MOTOR HOME CHASSIS IS RATED FOR TOWING OPERATION AT GVWR NOT GCWR CONSULT YOUR CHASSIS OWNER S MANUAL S FOR SPECIFIC WEIGHING INSTRUCTIONS AND TOWING GUIDELINES THE BRAKING CAPACITY OF YOUR MOTOR HOME IS NOT NECESSARILY AS GREAT AS THE TOWING CAPACITY SEPARATE BRAKING SYSTEMS SHOULD BE USED FOR CONTROL OF A TOWED VEHICLE AUTO TRAILER BOAT ETC BEHIND THE MOTOR HOME IF THE TOWED VEHICLE MEETS OR EXCEEDS THE MINIMUM WEIGHT AS DETERMINED BY THE CHASSIS MANUFACTURER THIS MINIMUM WE
13. The weight of the holding tank contents is not calculated into the motor home cargo carrying capacity this extra weight would reduce your available cargo capacity Traveling with full holding tank s could possibly cause you to exceed the individual tire ratings and or the motor home GAWR or GVWR Potential damage to suspension components such as springs tires and axles could result If your motor home holding tank s are located behind the axles the weight of the full tank s will reduce the hitch weight Motor home sway and other handling difficulties can be the result of the hitch weight being too light Never travel with full black or grey water holding tanks This not only wastes your fuel but depending on the location of the tank s it can affect your vehicle handling characteristics Dump the gray and black water holding tanks before traveling to avoid carrying unnecessary weight If you are dry camping and cannot immediately empty your holding tanks reduce your vehicle speed until you reach a dumping station When connected to the sewer drain line at a campground keep the black tank drain valve closed until the holding tank is at least 34 full This should provide sufficient water to assist in complete draining of the black water holding tank Repeat as needed Before using the motor home or after dumping the grey and black water holding tanks always add the proper amount of deodorant to the black water tank to prevent
14. if so equipped While you are putting antifreeze in the water lines follow these instructions to winterize the dishwasher a Use the dishwasher remote control to unlock the dishwasher Open the dishwasher and select RINSE Close the dishwasher and the rinse cycle should begin This will bring antifreeze into the dishwasher through the water lines Pause the dishwasher with the remote wait for 3 beeps open the dishwasher and add several cups of antifreeze into the tub Close the dishwasher re start it with the remote then press and hold the button on the remote until you hear a quick double beep The dishwasher will drain the antifreeze into the pump assembly Winterizing Clothes Washer if so equipped While you are putting antifreeze in the water lines follow these instructions to winterize the clothes washer a 106 Set the Cycle Selector to RINSE Set the Wash Temperature to WARM Press the ON OFF button to turn the washer on Press the START button to begin the rinse cycle Antifreeze should flow into the drum When antifreeze begins flowing in the drum press and hold the START button to cancel the rinse cycle Add several cups of antifreeze in the drum Turn the Cycle Selector to DRAIN Press the START button to begin draining the antifreeze out of the drum and into the pump assembly When antifreeze disappears out of the drum press and hold the START button to cancel the Drain cycle Press the ON O
15. 6 Water will flow into the fresh water tank To disconnect During the filling process periodically check the fresh water tank level using the Monitor Panel located in the Command Center When the fresh water tank is full it is normal to see water running from the fresh water overflow tubes onto the ground 7 Shut OFF the water at the external water source 8 Disconnect the non toxic drinking water hose from the water source and then from the City Water Connection inlet Reinstall the city water connection inlet cap Country Fill This setting is used to siphon fill the water tank from a water container when dry camping when a pressurized water source is unavailable 1 If needed sanitize the water system prior to travel 2 If equipped with a tank storage water heater set the bypass valves to the NORMAL postion supply line valves ON middle valve OFF Tankless water heater will not have bypass valves 3 Remove the City Water Connection inlet cap and attach one end of the supplied short hose to the City Water Connection inlet at the utility center Place the other end of the hose in a container of water 4 Place the utility center water valves in the Country Fill position 5 Turn ON the water pump Water will be drawn out of the container and into the fresh water tank To aid siphoning place the container on a flat surface approximately 2 feet off the ground All low point drains must be OFF in order to create
16. Do not use carbon cartridges where water is microbiologically unsafe or of unknown quality Maximum operating pressure is 125 psi 8 75 bar Maximum water temperature is 125 F 52 C 93 PLUMBING SYSTEM Lx A Et ZUL WATER HEATER Hydrogen gas may result if you have not used the water heater for two weeks or more HYDROGEN GAS IS EXTREMELY FLAMMABLE To reduce the risk of injury under these conditions open the hot water faucet for several minutes at the kitchen sink before you use any electrical appliance connected to the hot water system If hydrogen is present you may hear what sounds like air escaping through the pipe as the water begins to flow Hydrogen gas may be present even after water has been drained from the water heater tank Open the faucet at the sink and allow the system to vent for five to ten minutes Do not smoke or have any open flame near the open faucet while venting On DSI water heater models make sure the switch is OFF Do not alter the operation or change the design construction of your water heater For your safety only factory authorized parts should be used on your water heater Accessories marketed for recreation vehicles such as an add on electric heating elements are not recommended by the manufacturer Such items are not approved to be installed and could create an unsafe condition and will void all warranties Operating Instructions If you smell propane gas
17. Each recreation vehicle has a ground fault current interrupter GFCI engineered into the electrical system This device has been designed to reduce the possible injury caused by electric shock The GFCI will not protect against short circuits or circuit overloads Test all GFCI receptacles monthly Push in the GFCI TEST button The GFCI RESET button should pop out indicating the GFCI receptacle has been tripped and interrupted 120 volt power Push in the GFCI RESET button to restore 120 volt power Contact your t independent dealer for assistance if the GFCI RESET button does not restore 120 volt power and pops back out A tripped GFCI breaker indicates that abnormally high 120 volt current flow a ground fault was detected through the electrical system grounding circuit A fault condition can be caused by faulty wire insulation wet wiring inside an appliance or faulty electrical equipment connected to the circuit etc All ground faults must be repaired before use of the motor home 120 voLT 30 AMP AC System IF So Equrppep Your recreation vehicle may be equipped with a 30 amp 120 volt 60hz AC electrical system The entire system is designed to operate on 1 leg of 120 volt power at a maximum current flow of 30 amperes Exposure to voltages higher or lower than a nominal 120 volts will damage or shorten the service life of the electrical system and appliances The 30 amp 120 volt 60hz AC electrical s
18. Jayco Customer First Emergency Roadside Assistance Obtaining Emergency Warranty Repair Obtaining Service For Separately Warranted Items Obtaining Service at Jayco Parts amp Accessories Notice To Jayco Dealers OCCUPANT SAFETY Secondary Means of Escape Exit Window Exit Window Label Fire Safety Fire Extinguisher Smoke Alarm Smoke detector warning label Combination Carbon Monoxide Propane Alarm Formaldehyde LP Carbon monoxide detector Formaldehyde label Extended Or Full Time Usage Cold Weather Usage Condensation PRE TRAVEL INFORMATION Vehicle Labels Weight Terms Towing amp braking warning label Federal OCCC and voluntary weight labels Federal OCCC and voluntary weight labels Loading Your Motorhome Federal label Motor home Weight Information label Trailer Plug Weighing Your Motor home 7 way trailer plug VEHICLE OPERATION Vehicle Operation Using The Rear Hitch Towing and braking label Braking amp Stopping Parking Brake Power Entry Door Step m KOOOVLOOO IRR NAN BS W 09 W 09 19 19 20 21 21 22 23 21 24 27 28 28 28 31 31 32 52 32 33 39 33 35 35 35 37 37 37 38 39 39 TABLE OF CONTENTS Entrance Door Keys Driver amp Front Passenger Seat Seat Belts Child Safety Restraint Systems Outside Rearview Mirrors Rear Vision Camera Backing Up Campsite Hook Up Electric Rear Stabilizer Control if so equipped Emergency Stopping Emergency Towing Front Axle Tire Align
19. MDSTMIDARDSP RS CACO KOR VERTICO SOGLOWONT SUE L THC ZARADE K MOTOR VE HELE AMT Tr SECITE CES V RS AUTOM OBL E REGULATES OTECT OH THC CATE OF OY CAMADA CN YGER ALA DATE 1A HAHLUF A TUAC SHOWA ABA FASC aT ON C15 Ss Motor home Weight Information label Federal label LOADING YOUR MOTORHOME Never load the motor home in excess of the GVWR or the GAWR for either axle Overloading your motor home may result in adverse handling characteristics and damage to the chassis When loading heavy objects keep them as low as possible preferably on the floor When loading heavy objects keep them as low as possible preferably on the floor Distribute cargo side to side so the weight on each tire does not exceed one half of the GAWR for either axle Store and secure all loose items inside the motor home before traveling Overlooked items such as canned goods small appliances on the countertop cooking pans on the range or free standing furniture items can become dangerous projectiles during a sudden stop 33 PRE TRAVEL INFORMATION 34 For traveling safety it is important to make sure the tie down straps are secured on all appliances such as the toaster coffee maker etc Vibration during travel will move the appliances creating the potential for them to fall out of their cabinets possibly causing injury The actual weight of the vehicle passengers all options liquids the hitch weight of your towed vehicle a
20. SAFETY Ea Repair or replace the combination carbon monoxide propane alarm when the alarm no longer functions As with any electronic product it has a limited life Alarms that do not work cannot protect you NOTE The carbon monoxide propane alarm manufacturer strongly recommends replacement of the detector five years after the date of purchase Refer to the Warranty Packet for more information from the carbon monoxide propane alarm manufacturer DO MOT AANT POWER PUISSANCE FAULT DEFAULT Chip every PP Bip toutes bes 40 seconds 40 secondes Owner s Manual Voir le manuel de l utiisatour CARBON MONOXIDE PROPANE CARBONE MONOXYDE 4 1 second Infowed kana ALARM ALARME 4 bips on 1 second suis Move to Fresh Air Cal 911 Allez resper Ge secondes de silence Ge l air frais a Sexterieur appelez le 11 LP Carbon monoxide detector alarm may vary from model shown M MITIOME WOOTTON A INSTUSTIONS IN IIe MACON eG NTS a FORMALDEHYDE Some components in the recreation vehicle contain formaldehyde based adhesives that may release formaldehyde fumes into the air for an unknown period of time Individuals who are allergic to formaldehyde gas fumes may experience irritation to eyes ears nose and throat Indoor air quality may also be affected by leaving your vehicle closed for a period of time To aid in dissipation ventilate the recreation vehicle by opening all windows and circulate the air with a fan The f
21. To expedite processing your warranty claim include your name address phone number RV 17 digit VIN and authorization number If returning parts include a copy of your return freight bill Obtaining weekend or after business hours repair assistance If an authorized Jayco dealer is not located nearby contact your selling dealer for assistance If your dealer is closed check with the campground staff or telephone yellow pages for an RV repair facility Have the item repaired and contact Jayco Customer Service immediately the following business day Failure to contact Jayco Customer Service unauthorized or improper warranty repairs or failure to return requested original parts may result in loss of reimbursements and or loss of warranty WARRANTY amp SERVICE E O E F O0 i SS OBTAINING SERVICE FOR SEPARATELY WARRANTED ITEMS Your selling dealer 1s responsible for servicing your recreation vehicle before delivery and has an interest in your continued satisfaction We recommend your dealer perform all inspection warranty and maintenance services Some dealers may be authorized service centers for those OEMs whose products are warranted separately and excluded from the Limited Warranty OBTAINING SERVICE AT JAYCO Should your RV be in need of service and your dealer recommend that the repairs be made at the Jayco Factory Service Center your RV may be returned to us with the following guidelines
22. and precautions before operating the recreation vehicle Even if you are an experienced RV er we encourage you to thoroughly read this Owner s Manual as well as the information contained in your Warranty Packet As technology advances new improvements enter the RV industry every day and each RV manufacturer has its own unique manufacturing process Familiarize yourself with the applicable warranties There are components that are excluded or warranted separately by their individual manufacturer s limited warranty refer to the Warranty Packet As the owner of the recreation vehicle you are responsible for regular and proper maintenance performed in accordance with this manual and the OEM manuals Regular and proper maintenance will help prevent conditions arising from neglect that are not covered by warranty Itis your responsibility and obligation to return your recreation vehicle to your dealer for warranty service repair CHANGE OF ADDRESS OWNERSHIP Please notify Jayco Customer Service as soon as possible of a change of address by writing or calling us For notification of a change of ownership please fill out the appropriate form located in this manual and mail it to Jayco Customer Service along with documentation showing proof of ownership Please include your current vehicle mileage motorized only DEALER RESPONSIBILITY At the time of sale of the new recreation vehicle your Jayco dealer is expected to Deliver yo
23. area Contact them for an appointment they will handle all warranty repair billing and returned parts for you 2 If you cannot locate an authorized Jayco dealer near you ask the campground staff for referrals or check the local telephone yellow pages Or contact Jayco Customer Service or your selling dealer for assistance in locating a repair facility a Contact the RV repair facility to discuss your situation and make an appointment Ask how their billing will be handled They may choose to bill Jayco directly otherwise you are expected to pay them b Have the RV repair facility inspect your RV Either they or you must call Jayco Customer Service to discuss applicable warranty coverage prior to any repair work being performed c Jayco Customer Service will issue an authorization number upon warranty repair approval and advise if any original parts need to be returned d Once Jayco Customer Service has issued an authorization number the RV repair facility may begin actual repair to your RV e Inspect the completed repair work thoroughly If you are not satisfied communicate that immediately to the RV repair facility management Make sure you are satisfied with the repair before you pay or leave the premises f For reimbursement either you or the RV repair facility must send a copy of your itemized repair bill and all requested return parts by UPS regular ground freight pre paid within 60 days of the completed repair date
24. circuit breakers and replace as needed Test by turning each circuit breaker off and back on Circuit breakers are wearable parts and must be replaced as needed as part of your RV maintenance If you have any questions consult your dealer A label is provided to explain the function of every 120 volt circuit breaker This label is located on or near the appropriate load center or sub panel and must remain permanently affixed to the motor home INVERTER IF so EouPPED Your RV may be equipped with a factory installed inverter that converts 12 volt DC current to 120 volt AC current It is important that you familiarize yourself with the inverter function and operation The inverter should be off when not in use The factory installed inverter is not intended for use with medical device s POWER CONVERTER The power converter converts 120 volt AC power to useable 12 volt DC power when the shore power cord is connected to an external power source The converter has a built in protective thermal breaker that will shut it down should overheating occur Overheating can be caused by operating the converter above its maximum power output for an extended period of time or by an obstruction to its ventilation air flow To reduce converter heat build keep unnecessary 12 volt lights and motors turned off Keep the converter cooling fins and fan clear of obstructions Inspection and maintenance If the 12 volt power converter is no
25. completed and received by Jayco Failure to file this warranty registration with Jayco will not affect your rights under this limited warranty as long as you can present proof of purchase but it can cause delays in obtaining the benefits of this limited warranty and it may inhibit any servicing facilities ability to provide proper repairs and or part replacement CARE AND MAINTENANCE It is your responsibility to perform proper care and maintenance of the RV and to assure correct load distribution For details regarding this please see your Jayco owner s manual and other component part manufacturers These outline various care and maintenance that is 17 WARRANTY amp SERVICE TT required to maintain your RV Please review all manuals supplied with the RV and contact Jayco or the supplier of the component part if you have questions Note failure to maintain the RV as noted in those manuals voids this limited warranty and any damage to the RV as a result of your failure to perform such care is not covered by this limited warranty THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE JAYCO INC 903 S Main Street P O Box 460 Middlebury IN 46540 Telephone 574 825 5861 or 800 283 8267 18 OCCUPANT SAFETY Eo SECONDARY Means oF Escape Exit Winpow Your recreation vehicle has been equipped with a window s that serves as a secondary means of escape The wi
26. corrosion due to the environment theft vandalism fire explosions overloading in excess of weight ratings and tampering with any portion of the RV LEGAL REMEDIES Any action to enforce any portion of this limited warranty or any implied warranty shall be commenced within six 6 months after expiration of the warranty coverage period designated above Any performance of repairs shall not suspend this limitation period from expiring Any performance of repairs after the warranty coverage period has expired or performance of repairs regarding any thing excluded from coverage under this limited warranty shall be considered good will repairs and they will not alter the express terms of this limited warranty or extend the warranty coverage period or this limitation period In addition this warranty is not intended to extend to future performance and nothing in this warranty or any action of Jayco or any agent of Jayco shall be interpreted as an extension of the warranty or this limitation period Some states do not allow a reduction in the statute of limitations so this reduction may not apply to you WARRANTY REGISTRATIONS Your warranty registration records should be completed and delivered to the manufacturers of component parts The Jayco product warranty registration form must be returned to Jayco within ten 10 days of your taking delivery of the RV Your Jayco warranty will not be registered unless this warranty registration is
27. cylinders on your recreation vehicle use only one at a time Otherwise the propane supply will be drawn equally from both cylinders until the supply has been totally exhausted Using one cylinder until it is empty then using the second cylinder will allow you to fill the empty cylinder at your convenience without running totally out of propane 82 FUEL amp PROPANE SYSTEM 0 CALCULATING PROPANE GAS USAGE It is important to remember that your furnace refrigerator water heater and range all may use propane gas to operate Each has a different BTU rating and you will need to consider them to determine how long your propane supply will last Most RV gas appliances are operated intermittently Propane consumption depends on individual use of appliances and the length of time operated Unless there is heavy use of hot water the water heater consumption of propane is minimal During cool temperature or high wind conditions furnace consumption can be extremely high To calculate your propane supply take the BTU ratings for your propane appliances and divide that into the BTU availability Each gallon of propane gas 3 785 liters produces about 91 500 BTU s 96 528 kilojoules of heat energy Propane consumption chart The following chart provides average propane consumption information A Average BTU ae Appliance Consumpionper Hout Kilojoules Hour 8 800 9 280 1 200 1 500 1 270 1 580 36 930 42 200 7 490 6 860 9 490
28. equipment Make sure that motor vehicle s are not and have not been operating in an attached garage or adjacent to the recreation vehicle If problems are identified during this inspection have the alarm serviced immediately Note any combustion equipment not inspected by the technician and consult the manufacturer s instructions or contact the manufacturer directly for more information about carbon monoxide safety and this alarm 25 OCCUPANT SAFETY LEHE FJO Oj gt Never turn the 12 volt battery disconnect control to the off position and disconnect the battery cable to silence an alarm The alarm will automatically sense when the level of carbon monoxide in the air reaches below dangerous levels You should stay outside the vehicle in fresh air until the alarm 1s silenced When the alarm sounds do not stand too close to the alarm The sound produced by the alarm is loud because it is designed to wake a person in an emergency Prolonged exposure to the alarm at a close distance may be harmful to your hearing Alarm Signals Normal Operation The LED will maintain a steady green light indicating that the alarm is powered CO alarm condition The red LED light will remain steady and the alarm will sound 4 BEEPS then silent for 5 seconds These signals indicate immediate action is required Propane gas alarm The red LED light will flash and the alarm will sound a steady to
29. housing dust cap back on the black tank flush The black tank drain valve must be OPEN any time there is a hose water supply connected to the black tank flush Do not leave any hose water supply connected to the black tank flush when it is not in use Do not use the same hose to fill your fresh potable water tank that is used for the black tank flush Black Tank Flush Inlet TANK Heaters IF So EquipPep Your recreation vehicle may be equipped with heaters for the fresh gray black water tanks and the water lines or drain lines The larger tank heaters are 120VAC and attach directly to the tanks Water line or drain line heaters are smaller and operate on 12VDC and will be attached to the water lines or drain lines These heaters will prevent water in the tanks and lines from freezing down to 11 F 24 C contingent on recreation vehicle setup The tank heaters are thermostat controlled and will cycle on and off while they are operating The 12VDC heaters oo I stay on constantly The thermostat controlled tank heaters wx S Y ako fe amp turn ON at 44 F 7 C and will turn OFF at 64 F 18 C B g T i E E All of the heaters are controlled by a single ON OFF RFS ase eee Ena Typically this red tank heater ON OFF switch is located g 7 T on the command center panel inside the recreation vehicle The switch lights up red when it is turned ON and controls the heater circuit
30. is loud to alert you to an emergency The test button will accurately test all functions Never use an open flame from a match or lighter to test this smoke alarm A warning label is located near the smoke alarm Please do not remove the following label from your recreation vehicle Test smoke alarm operation after vehicle has been in storage before each trip and at least once per week during use Failure to do so can result in death or serious injury E KE PRIE DE EN SI LE V HICULE A T ENTREPOS AVANT CHAQUE D PLACEMENT ET AU MOINS UNE FOIS PAR SEMAINE EN SERVICE Smoke detector warning label 22 OCCUPANT SAFETY Test the smoke alarm operation after the vehicle has been in storage before each trip and at least once per week during use Do not disconnect the battery or the alarm Maintenance Gently vacuum off any dust on the cover of the smoke alarm with your vacuum s soft brush attachment Test the smoke alarm once you have vacuumed Never use water cleaners or solvents to clean the smoke alarm as they may damage the smoke alarm Do not paint the smoke detector For information on how to maintain your smoke detector refer to the smoke detector user s guide Battery The smoke alarm will not function if the battery is missing disconnected dead the wrong type of battery is used or the battery is not installed correctly The smoke detector requires one standard 9V battery When the battery becomes w
31. lug nuts you should always have the wheels mounted and properly torqued by a qualified technician using the proper tools After your first trip check the wheel lug torque periodically for safety according to your Chassis Guide If you suspect the wheel lug nuts have loosened at any time have them checked and torqued to the proper limits immediately Check and re torque after the first 10 25 and 50 miles 16 40 and 80 kilometers Thereafter check and maintain the torque according to the listed torque values Wheel lugs If you suspect or notice the wheel stud bolts are cracked or broken they must be replaced along with adjacent bolts that have probably also been weakened due to the additional stress placed on them WHEEL BEARINGS amp BRAKES Follow the Chassis Guide maintenance instructions for the front and rear axle for wheel and suspension maintenance including the brakes and wheel bearings Contact your Chassis manufacturer for assistance 46 VEHICLE OPERATION A TIRES Read and understand the following before taking your first trip in your RV Proper care and maintenance of your tires 1s essential to ensure your safety as well as the safety of others as you travel Routine maintenance on your motor home is important but it cannot be overstated just how critical proper tire maintenance 15 to the safety operation and durability of your new vehicle You must follow the manufacturer s inflation guidelines for maxi
32. motor home should be winterized at the end of the camping season or when the motor home will be exposed to temperatures that will fall at or below 32 F 0 C Repairs due to freezing are not covered by warranty The preferred method is to winterize the plumbing system with RV antifreeze Please read understand and follow all instructions before beginning Never apply air pressure to the water system with any of the valves in the closed position Air pressure applied to a closed valve faucet or low point drain could potentially damage the seals and cause water leaks If you have questions consult with your RV dealer Winterizing with Antifreeze method It may be easier to winterize the motor home with another person to assist you 1 Level the motor home and drain the fresh water plumbing system 2 Turn the water valves OFF on each side of the water filter canister Canister is located behind the utility center Unscrew the canister and remove the filter Re attach the empty canister and turn the water valves ON Refer to the Water Purification section 3 Water heater power switches 12V GAS amp 120V ELECTRIC at the Command Center should be turned OFF Gas valve at the water heater should be turned OFF Tankless water power switch is located outside the RV 4 Turn the water heater bypass valves if so equipped to the BYPASS position Tankless water heater will not have bypass valves 5 Move the valves to the Sanitize W
33. output that exceeds 12 volt Use adequate ventilation when charging or using the battery in an enclosed space Replacement and maintenance For accuracy test battery voltage using a volt ohm meter customer supplied When it is time to replace the house batteries replace with Group 27 deep cycle batteries only Contact the battery manufacturer for further information Do not reverse the positive and negative battery cables Doing so will blow the reverse polarity fuses that protect the power converter Chassis Battery Each chassis is built with batteries to provide energy to start the engine and operate devices supplied with the chassis The chassis battery is furnished and warranted by the chassis manufacturer as applicable AUXILIARY START SYSTEM Your motor home is equipped with an auxiliary start switch which can momentarily connect both the house and chassis batteries should the chassis battery become discharged To operate depress the Aux Start switch located on the front driver s dash and hold it down While the Aux Start switch is depressed use the ignition key to start the chassis engine Release the Aux Start switch after the engine has started 12 VoLT BATTERY DISCONNECT The 12 volt battery disconnect switch 1s located near the entrance door This momentary switch controls a latching type solenoid located near the house batteries which connects or disconnects the house batteries dependent upon th
34. pre wired into your motor home Wiring to operate your towed vehicle brakes must be the same size in both the towed vehicle and the motor home White 1 Ground Blue 2 Brakes Green 3 Running lights Black 4 House batteries charge line Red 5 Stop amp left turn Brown 6 Stop amp right turn HY Yellow 7 Back up ee feiler plug Car end rear view Maintenance The connector plug may build up corrosion with extended use and should be cleaned periodically to insure good electrical contact Make sure the connector plug is kept clean and protected from road elements as you travel WEIGHING Your MOTOR HOME Now that your motor home is loaded you should have it weighed The actual weight of the motor home passengers all options liquids the hitch weight of your towed vehicle and your personal cargo is important for you to know so you do not exceed the GVWR There are two important factors when loading your motor home total weight and balance It is imperative that you verify compliance within all applicable weight ratings Overloading your motor home will void the Limited Warranty and the warranties of many component part manufacturers Have your RV weighed periodically at a public scale to determine the proper load distribution Keep in mind that individual scales will operate differently The surroundings of the scale need to be adequate to accommodate weighing each side of your motor home
35. sealants use a stepladder placed safely alongside the vehicle Do not prop a ladder against the body of the motor home as it may damage the exterior finish 133 EXTERIOR U Notes 134 TRAVEL CAMPING STORAGE CHECKLISTS LAA RV START UP The following checklist will help ensure a trouble free camping season Inspect and work all interior and exterior latches and locks lube if necessary Make sure the batteries are fully charged and installed correctly Turn ON the motorhome 12 volt battery disconnect switch Inspect the power cord and carefully clean the contacts if necessary Plug in the power cord to an appropriate power source Turn on the interior lights and check outlets for polarity If needed replace any blown fuses Check the circuit breakers and test the GFCI Inspect and test all safety detectors If needed replace any drained or discharged batteries If you have a defective or damaged safety detector replace it immediately Inspect and turn on the propane system If you have any questions contact your dealer or a qualified propane service representative for assistance If the propane system is functioning properly test the pilot lights on range refrigerator furnace and water heater if so equipped Inspect the leveling jacks if so equipped for operation If needed perform maintenance as specified by the
36. test for open neutral open ground and correct polarity Do not hook up the power cord to any receptacle until you have verified proper polarity and grounding Polarity indicators can be purchased in most electrical and hardware stores Do not use any cheater plug adapter or extension cord to reconfigure incoming AC power or break the continuity of the circuit connected to the grounding pin Do not connect the power cord into an outlet that is not grounded or adapt the power cord plug to connect it to a receptacle for which it is not designed Do not remove the grounding pin to connect to a non grounded receptacle Removal of the ground pin disables an important safety feature designed to prevent shock and electrocution hazards Do not connect the power cord to an extension cord Use of an improper extension cord will cause overheating of the cord as well as potentially causing premature failure of the AC equipment It is the responsibility of the owner of the electrical receptacle to ensure that the receptacle is properly wired and grounded Reverse polarity and or improper grounding of your RV can cause personal injury or death 30 amp Power Corp IF So EouIPPED PLUG INTO 30 AMP SERVICE ONLY The 30 amp external utility power cord is commonly referred to as the shore power cord It is designed to mate and properly function with 30 amp shore power recept
37. towards you firmly and gently Activate or deflate the air mattress if so equipped using the supplied furniture manufacturer s instructions To convert the hide a bed back into the upright sofa position reverse the process Jack Knife Sofa If So Equipped The Jack Knife sofa functions much the same as a residential futon To make the sofa in to a bed lift up on the bottom seat cushion and pull it towards you The sofa back will drop down to provide a sleeping surface For additional comfort and to reduce fabric damage you may want to place a cover or air mattress customer supplied over the sofa when it is in the sleeping position Trifold Sofa If So Equipped The Trifold Sofa offers very similar features to the traditional hide a bed The following illustrations detail converting the sofa into a bed 123 INTERIOR aa 2 Using the strap handle pull 1 Remove tri fold sofa pillows and sleeping surface up then out set aside 3 While sleeping surface is up gold out legs i 4 Once sleeping surface is grounded fold Extend sleeping surface until grounded headboard dawn flat FREE STANDING TABLE AND CHAIrRs IF So EouIPPED Two free standing chairs and two folding chairs are included in the Free Standing Table chair Package if so equipped When traveling it is recommended the free standing dinette chairs be fastened securely at the dinette table and the folding chairs be secured BoorH DINETTE IF So
38. vehicle because a fire or explosion may result Fuel selection Use diesel fuel only Remember the diesel generator if so equipped is also fueled by the same system used to fuel the motor home chassis engine Consider the fuel requirements of the diesel generator if so equipped when making a decision on the type of fuel to use DEF Fluid Diesel engines since 2010 require the use of DEF fluid Diesel Exhaust Fluid to aid in burning particulate matter in the exhaust and reduce emissions to nitrogen and water This DEF fluid is kept in a separate heated tank and is required for the normal operation of the diesel engine DEF tank 1s typically located in one of the exterior compartments and the tank will have a blue cap with DEF written on it There will be a series of warnings at the dash before running out of DEF fluid If the vehicle is allowed to run out of DEF fluid engine power is intentionally reduced and speed will be limited to 5 MPH until the tank is re filled NOTE f your motor home is equipped with a diesel generator check the diesel generator and chassis manufacturer s information to help you determine the type of diesel fuel best suited for this dual application Use care when fueling your motor home The label listed below should be kept permanently affixed to your motor home AN DANGER ALL PILOT LIGHTS APPLIANCES AND THEIR IGNITORS SEE OPERATING INSTRUCTIONS SHOULD BE TURNED OFF BEFORE REFUELING OF MOTO
39. vehicle information available All work to be performed may not be covered by the warranty Discuss additional 6 WARRANTY amp SERVICE ME JI charges with the service personnel Prepare a list Provide your dealer with a written list of specific repairs needed It is important that you provide any vehicle repair history to the dealer s service personnel Keep a maintenance log of your vehicle s service history This can often provide a clue to the current issue Be reasonable with your requests If you leave a list with several items and you need your vehicle returned back by a specific time discuss the situation with the dealer s service personnel and list your items in order of priority This may include making a second appointment for work not completed or parts that the dealer may need to order Don t expect to look over the technician s shoulder Please don t be offended if you are told you cannot watch the work being done Some insurance requirements forbid admission of customers to the service area Inspect the work performed Finally check out the service or repair job when you pick up your vehicle Notify the dealer s service personnel immediately of any dissatisfaction If you can t return the vehicle immediately for repair make an appointment as soon as possible Please be aware that all service shops require notification of any issues with their repairs within a specified time limit Make sure
40. water pump is ON Remove the handheld shower from its holder Turn ON the hot and cold faucet knobs and adjust the water temperature as desired aS SS YS To activate the handheld shower turn ON the sprayer head attachment some models To turn off the water always close the faucet knobs The lever on the shower head will not completely stop the flow of water this is intentional to allow for draining After the water 100 PLUMBING SYSTEM oo has been allowed to drain from the shower head return it to the outside shower compartment Any remaining water in the shower hose will drip or run out this is not a leak but performs as intended If you are dry camping turn the water pump OFF Water should always be turned off using the hot cold control knobs rather than turning off the water with the lever on the shower head Turning off the water with the shower head lever can create a condition where the hot and cold water will mix through the outside shower faucet thereby reducing the temperature of the hot water It can appear as though the hot water heater is not working properly CN XN AN NOTE The shower head may be removed from the hose so that it will drain faster If you remove the shower head be sure to reas semble it prior to storage NOTE When putting the shower assembly back into the storage compartment make sure the hose is not pinched or the shower head IS positioned in a way it can be damage
41. water tank drain and the low point drains are closed a siphon is created in the water lines allowing sanitizer to be pulled into the fresh water tank Use the short hose supplied with your motor home Refer to the Sanitization section Sanitize Winterize Lines Setting This setting is typically used for drawing RV antifreeze into the water lines of the motorhome When the fresh water tank drain and low point drains are closed a siphon is created in the water lines to draw antifreeze out of a container and into the water lines Use the short hose supplied with your motor home Refer to the Winterization section WATER PURIFICATION System IF So EoulIPPED Depending on the model your recreation vehicle may have a full canister style water purification system If the water supply has not been used for some time allow the water to flow for several minutes to flush the system NOTE F ilters should be replaced at the beginning of each camping season or if they have come into contact with contaminated water NOTE When not in use the water filter cartridge should be stored out of freezing temperatures RV antifreeze will damage the water filter cartridge To Replace Filter Cartridge 1 Turn off water supply using two valves located on the water lines on each side of the canister Place drip pan below filter housing to catch any spillage Press the red button on top of the filter housing to release pressure 4 Using a spanner
42. when cooking or washing dishes Avoid hanging wet towels or clothes inside the recreation vehicle to dry If condensation is found in cabinets or closets open those doors slightly to equalize the temperature and provide ventilation 29 OCCUPANT SAFETY La M S A Xx Notes 30 PRE TRAVEL INFORMATION ma VEHICLE LABELS Decals and data plates used throughout the motor home aid in its safe and efficient operation others give service instructions Read all decals data and instruction plates before operating your recreation vehicle Any decal data or instruction plate painted over damaged or removed should be replaced Keep a record of the 17 digit chassis vehicle identification number VIN the 9 digit serial number and your license number in the event theft or vandalism requires you to supply this information to the authorities The factory installed weight labels are specific to the recreation vehicle for which they are supplied and are not interchangeable Do not remove these labels from your vehicle If labels are missing contact your dealer or Customer Service for replacements WEIGHT TERMS Your motor home braking system is designed and rated for operation at GVWR not GCWR GROSS VEHICLE WEIGHT RATING GVWR The value specified by the manufacturer as the maximum permissible weight of the fully loaded motor home GROSS AXLE WEIGHT RATING GAWR The value specified by the vehicle manufactu
43. with obtaining service including by way of example travel costs are specifically excluded from the coverage of this warranty In addition this limited warranty does not cover any material component or part of the RV that is warranted by another entity including by way of example the automotive chassis and power train steering handling braking wheel balance muffler tires tubes batteries gauges generator hydraulic jacks inverter converter microwave television DVD CD player radio speakers television refrigerator range hot water heater water pump stove carbon monoxide detector smoke detector propane detector furnace or any air conditioner Note The written warranty provided by the manufacturer of the component part is the direct responsibility of that manufacturer Defects and or damage to interior and exterior surfaces trim upholstery and other appearance items may occur at the factory These items are usually detected and corrected at the factory or by the selling dealer prior to delivery to the retail customer You must inspect your RV for this type of damage when you take delivery If you find any such defect or damage you must notify the selling dealer at time of delivery to have these items covered by this limited warranty and to have work performed on the items at no cost to you as provided by this limited warranty EVENTS DISCHARGING JAYCO FROM OBLIGATION UNDER WARRANTY Certain things completely discharge J
44. wrench rotate the filter housing Unscrew the housing completely and remove the filter dispose of the old filter properly 5 Clean the inside of the filter housing with mild detergent Thoroughly rinse and wipe clean 6 Remove the o ring from the groove in the housing and wipe clean Recoat with petroleum jelly Filter housing 92 PLUMBING SYSTEM Eo Replace the o ring in the groove making sure it is properly seated Install the new filter cartridge Replace the canister housing hand tighten is normally sufficient 10 Turn on the water supply and check for leaks NOTE There is no bypass feature on a canister style water filter The water filter must be removed before sanitizing or winterizing the RV Each new RV is winterized with RV antifreeze before it is shipped to the dealer To use the water purification system full system canister water lines need to be flushed of antifreeze and then the filter installed in the canister before use Refer to the manufacturer s owner s manual and the label on the water filter cartridge for further information Do not allow the filter housing to freeze Remove the cartridge before using anti freeze to winterize the system or chlorine solution to sanitize the system Flush housing thoroughly before it is put back into service after winterizing or sanitizing For best results replace cartridge every 6 12 months
45. 10 550 CooKING WITH PROPANE GAS Do not turn gas range burner controls to ON and allow gas to escape before lighting Do not use portable fuel burning equipment 1 e wood and charcoal grills or stoves inside the recreation vehicle Unlike homes the amount of oxygen supply is limited due to the size of the recreation vehicle Proper ventilation when using the cooking appliance s will help you avoid the danger of asphyxiation It is especially important that cooking appliances not be used for comfort heating as the danger of asphyxiation is greater when the appliance is used for long periods of time FAILURE TO COMPLY MAY RESULT IN DEATH OR SERIOUS INJURY The following warning labels are located in the cooking area to remind the user to provide an adequate supply of fresh air for combustion 83 FUEL amp PROPANE SYSTEM Ne TO ENSURE A SUPPLY OF FRESH AIR TO OCCUPANTS OPEN VENTILATORS WHEN FUEL BURNING RANGE FUEL BURNING CARRY ON APPLIANCE AND OR FUEL BURNING LIGHTS ARE IN OPERATION COOKING APPLIANCES SHOULD NOT BE USED FOR SPACE HEATING PURPOSES DE MANIERE A ASSURER UNE ALl MENTATION EN AIR FRAIS AUX OCCU PANTS OUVRIR LES VENTILATEURS LORSQUE LA CUISINERE LES AP PAREILS DE CHAUFFAGE PORTABLES ET OU LES LAMPES DE COMBUSTION D HUILE SONT EN FONCTIONNEMENT LES APPAREILS DE CUISSON NE DOIVENT PAS SERVIR AU CHAUFFAGE DES LOCAUX JA 110 Ensure a supply of fresh air Canada units only A DANG
46. 2016 MELBOURNE CLASS C MOTORHOMES Jayco Generations of family fun 012956 18 to PRINTED ON RECYCLED PAPER THE JAYCO ECOADVANTAGE IS OUR COMPANY S COMMITMENT TO PROTECTING THE ENVIRONMENT Through Jayco s company wide sustainability program we re creating better ways to build better RV s using fewer natural resources Already our initiative has created significant impact As of 2014 our company has Recycled ork e 7 192 tons of wood e 2 354 tons of scrap metal e 1 428 tons of cardboard and paper Conserved e 9 997 400 gallons fo fresh water enough to meet the daily needs of 133 293 Americans e 34 277 gallons of gas enough for Americans to drive more than 957 600 miles e Enough electricity to power 1 745 homes for tha year Saved e 60 900 mature trees A e Enough landfill airspace to meet the annual disposal W needs of a community of 44 683 people We re proud of our results and we know those numbers show that a little initiative can go a long way The Jayco EcoAdvantage is our way of making sure endless generations can enjoy the Great Outdoors TABLE OF CONTENTS WARRANTY amp SERVICE About This Manual Warranty packet Chassis Guide Safety Alerts Reporting Safety Defects Manufacturing Process Options amp Equipment Customer Responsibility Change Of Address Ownership Dealer Responsibility Customer Relations Jayco Travel Club JayPlus Extended Service Contract
47. AL DAMAGES THAT MAY RESULT FROM BREACH OF THIS LIMITED WARRANTY OR ANY IMPLIED WARRANTY THIS EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES SHALL BE INDEPENDENT OF ANY FAILURE OF THE ESSENTIAL PURPOSE OF ANY WARRANTY AND THIS EXCLUSION SHALL SURVIVE ANY DETERMINATION THAT THIS LIMITED WARRANTY OR ANY IMPLIED WARRANTY HAS FAILED OF ITS ESSENTIAL PURPOSE Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you 15 WARRANTY amp SERVICE TT HOW TO GET SERVICE To obtain reimbursement of warranty service the owner must do all of the following Notify Jayco of the substantial defect in material or workmanship attributable to Jayco within the warranty coverage period 1 Provide the notification mentioned in 1 above within ten 10 days of when the owner discovered or should have discovered the substantial defect in material or workmanship attributable to Jayco 2 Promptly and appropriately make the necessary repairs and Pay any freight or transportation costs import duties fees and all incidental expenses associated with obtaining warranty service If you need assistance you may contact Jayco at 903 S Main Street P 0 Box 460 Middlebury Indiana 46540 Attn Customer Service 574 825 5861 800 283 8267 or www jayco com Also you must notify Jayco within three 3 da
48. After turning on propane except after normal cylinder replacement test propane piping and connection to appliances for leakage with soapy water or bubble solution Do not use products that contain ammonia or chorine DD 37 Propane label Maintenance Although your motor home has been carefully tested at the factory and by your selling dealer for leakage travel vibrations can loosen fittings Have the vehicle propane system checked at all connections soon after the purchase of your vehicle and after the initial filling of the propane tanks NOTE All propane lines have been checked with air pressure at the time of manufature Dealers are required to recheck and adjust pressure before retail delivery Continued periodic checks of the propane system at 5 000 miles of travel or at least once a year by a qualified propane service representative as part of your normal maintenance is recommended Hand tighten the LP gas system valves only do not use a wrench or pliers as over tightening may damage the valve seals and cause them to leak PROPANE LEAK TEST Leaks may be found easily with a soapy water solution Do not use a solution containing ammonia or chlorine when locating leaks These products are corrosive to copper gas lines and brass fittings which could result in deterioration of the copper and brass components Apply the soapy solution to the outside of the gas piping fittings If a leak is present the soapy solution will bub
49. C Insurance or call 1 877 484 2261 Savings Code GL 2A Jayco Customer First EMERGENCY ROADSIDE ASSISTANCE Jayco has teamed up with Coach Net the largest RV emergency road service in the country to give you 24 hour 7 days a week assistance in obtaining dependable service when and where you need it We are offering this free of charge for the first year of ownership from the date of purchase certain restrictions apply You may continue your Customer First Roadside Assistance benefits in the following years WARRANTY amp SERVICE ME JI by contacting Coach Net to discuss any applicable terms and rates for this independently continued coverage at 1 877 801 0333 For further details and instructions on how to access your Roadside Assistance benefits please refer to your Member Benefit Guide which will be mailed 6 8 weeks from the date the completed Warranty Registration and Customer Delivery Form is received by Jayco or by contacting Coach Net www coach net com at 1 877 801 0333 To qualify for coverage your RV must be eligible as set forth under the terms of the applicable Limited Warranty offered by Jayco OBTAINING EMERGENCY WARRANTY REPAIR A roadside emergency can happen at any time whether your recreation vehicle is new or old If you are traveling using the following guidelines can help get you back on the road faster 1 Call 1 800 RV JAYCO or use our website dealer locator to find an authorized Jayco dealer in your
50. Check wheel nuts for tightness and tires for proper air inflation pressure Check the propane tank gauge to make sure there is propane available If needed sanitize the fresh water system 135 TRAVEL CAMPING STORAGE CHECKLISTS cic CCOO Fill the fresh water tank Disconnect drain and store the garden hose on the bracket Retract any awnings and secure them for transport Close all the roof vents Disconnect the cable TV and phone hookups and lower the TV antenna Turn off the interior lights water heater furnace and water pump Secure any loose heavy or sharp objects in the motor home or exterior compartments Disconnect the 50 amp power cord and ensure it is stored correctly Fasten all interior and exterior doors securely Lock them if applicable Make sure the leveling jacks are retracted to the travel position Walk around your motor home one last time to make sure everything is stored away and the baggage compartments are closed and locked Check the seat belt buckles and release mechanisms for positive action and secure connections Secure and lock the entrance door For more information Read and follow the instructions in your Chassis Guide regarding pre trip inspections and daily maintenance DEPARTING Camp CHECKLIST When the time arrives to return home it is again critical that you complete the n
51. D The Jayco warranty covers the house portion of this recreational vehicle RV when used only for its intended purpose of recreational travel and camping for two 2 years or the first twenty four thousand 24 000 miles of use whichever occurs first It covers RV s that are sold in and remain in the United States U S Territories and Canada only The house portion means the living area of the RV assembled by Jayco The warranty period begins on the date that the RV is delivered to the first retail purchaser by an independent authorized dealer of Jayco or if the dealer places the vehicle in service prior to retail sale on the date the RV is first placed in such service In the event that a substantial defect in material or workmanship attributable to Jayco is found to exist during the warranty period it will be repaired or replaced at Jayco s option without charge to the RV owner in accordance with the terms conditions and limitations of this limited warranty This limited warranty applies to the first consumer purchaser only All rights and limitations within this warranty are applicable to the original owner of the RV only Jayco s limited 10 WARRANTY amp SERVICE ME JI warranty only covers substantial defects in materials components or parts of the RV attributable to Jayco It does not replace modify or apply to the warranties provided by the manufacturers that supply the products used by Jayco to assem
52. DVD CD player radio speakers television refrigerator range hot water heater water pump stove carbon monoxide detector smoke detector propane detector furnace or any air conditioner Note the written warranty provided by the manufacturer of the component part is the direct responsibility of that manufacturer Defects and or damage to interior and exterior surfaces trim upholstery and other appearance items may occur at the factory or during delivery of the RV to you These items are usually detected and corrected at the factory You must inspect the RV for this type of damage when you take delivery from Jayco If you find any such defect or damage you must notify Jayco within three 3 days of delivery of the RV to you to have these items covered by this limited warranty and to have work performed on the items covered by this limited warranty EVENTS DISCHARGING JAYCO FROM OBLIGATION UNDER WARRANTY Certain things completely discharge Jayco from any obligation under this warranty and void it By way of example the following shall discharge Jayco from any express or implied warranty obligation to repair or replace any defect that results from any defect in a separately manufactured component part any neglect or failure to provide routine maintenance by you or anyone you rent the RV to See Owner s Manual unauthorized alteration off road use collision or accident whether or not foreseeable including any acts of weather or damage or
53. ER Do not use gas cooking appliances for comfort heating Can lead to carbon monoxide poisoning which can lead to death of Serious injury Before operating Gas cooking applances need fresh air for safe operation Open vents or windows shghtly or tum on exhaust fans prior to using cooking appliance Gas flames consume oxygen which should be replaced to ensure proper combustion improper use can resul in death or serious injury Cooking comfort heating label TRAVELING WITH PROPANE A N XN NN NJ NOTE Some states prohibit propane appliances to be operated during travel especially in underground tunnels Make sure you know the laws for the areas where you travel Use care when fueling your motor home Make certain your propane tank is properly fastened in place The label listed below should be kept permanently affixed to your RV A DANGER 84 ALL PILOT LIGHTS APPLIANCES AND THEIR IGNITORS SEE OPERATING INSTRUCTIONS SHALL BE TURNED OFF BEFORE REFUELING OF MOTOR FUEL TANKS AND OR PROPANE CONTAINERS FAILURE TO COMPLY COULD RESULT IN DEATH OR SERIOUS INJURY AIDS Refueling warning label PLUMBING SYSTEM oo There are two different water systems in your recreation vehicle The fresh water system consists of the fresh water holding tank fresh water connections water pump outside shower assembly if so equipped water heater faucets tub shower and water purifica
54. ESH WATER SYSTEM All water contains contaminant and mineral particles that can cause fresh water system odors Untreated well water is a major source of water system odors The fresh water or potable water system needs periodic sanitization and winterization to take care of all the components within the plumbing system and help discourage the growth of bacteria and other organisms that can contaminate the water supply DO NOT drink water deemed microbiologically unsafe or of unknown quality 86 PLUMBING SYSTEM oo Never travel with full fresh black or grey water holding tanks FRESH WATER HOLDING TANK There may be several ways to fill the fresh water tank depending on the model For details of each method refer to the Fresh Water Connections or the Utility Center if so equipped sections There are plastic overflow tubes plumbed into the fresh water holding tank They allow water to flow out of the water tank refer to the City Water Fill section Occasionally you may see water coming from the overflow tubes when the fresh water holding tank is filled This is normal and is caused by external circumstances including the recreation vehicle being parked on an incline or the motion caused by starting or stopping the recreation vehicle during travel Indicates a potentially hazardous situation that if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices Indicates a po
55. EquipPeD The dinette is designed to seat up to four adults You can access the dinette bench storage by removing all the cushions and lifting the bottom seat supports If the dinette bottom seat support is screwed shut it is to protect factory installed equipment do not use that area for storage To convert the booth dinette to a bed determine which type of booth dinette you have Booth Dinette Remove all the cushions from the booth dinette Lift the tabletop remove the detachable table legs and place the tabletop on the ledges provided between the booth dinette benches Lay the seat back cushions against the back of the booth dinette bench Lay the dinette seat bottom cushions in between the seat back cushions The area where the cushions meet should be slightly raised Push the raised cushion ends down gently The cushions are designed to fit snugly Reverse this process when converting back to the booth dinette Dream Dinette Remove all the cushions from the booth dinette Underneath the table there is a rod that acts as a locking mechanism to keep the table from collapsing into the bed configuration Turn this rod so the rod moves out of the channel and points down toward the floor see photos Then simply push the dinette table down toward the floor to form the platform for the bed Arrange the cushions to form a mattress for sleeping To convert back to a dinette remove the cushions pull the table back up as high as it will go and tu
56. FF button to turn off the washer PLUMBING SYSTEM oo To De winterize both the dishwasher and clothes washer run a regular empty wash cycle which will remove antifreeze from the washer and water lines After that the washer can be used normally BLACK GREY WATER SYSTEM Water from the sinks and shower or tub flow into the gray water or waste water holding tank Water from the toilet will flow into the sewage or black water holding tank Certain floor plans may also have the lavatory draining into the waste black tank Drain pipes The drain pipes have a P trap installed to help prevent odors from escaping into the motor home During travel water from the P traps may spill and permit odors into the motor home These odors come from food particles decomposing in the tank By adding water and using a RV approved deodorizing agent you will dissolve the contents faster and will keep the drain lines and tanks clean and free flowing These chemicals are available at an RV supply store or your dealer Vents Another important part of this system is the vent pipes and vents that release air from the grey and black water holding tanks The exterior vent cap is attached to the roof and must be kept clear of obstructions to perform as intended On some models the vent pipe may be part of the drainage system referred to as a wet vent water flows downward as air flows upward in the same pipe BiackK GREY WaTER HOLDING TANKS
57. FRESH WATER SYSTEM Permanent water tanks may be drained through a valve located near the tank A recreation vehicle with a demand pressure pump system will have low point drains attached to the water lines normally located near the water tank These low point drains will release water in the supply lines by opening the valves and all faucets The water heater has its own drain plug To drain the permanent fresh water holding tank and supply lines 1 Turn the water heater power OFF Turn off the Electric amp LP GAS switches 2 Open all faucets including the outside shower faucet 3 Open the fresh tank drain valve All permanent fresh water tanks can be drained by one of two types of drain valves A white plastic drain is attached to the exterior wall open valve to drain or a valve located inside the motor home adjacent to the water tank this knob turns 45 to open or close 4 Open the low point drains by turning then pulling the handles up As their name indicates they will be at the lowest point of water lines A label is placed on the outside 102 PLUMBING SYSTEM oo of the RV to indicate where the drains are located The drains will typically need to be opened from inside the motor home Once the label is found on the exterior sidewall go inside the E x eo Vii motor home to find the corresponding location of the drains MJ AJ Drain the sink by removing the drain cap A 4 Turn
58. IGHT RATING WILL VARY BY CHASSIS AND CHASSIS MANUFACTURER CONTACT YOUR CHASSIS DEALER OR MANUFACTURER FOR ASSISTANCE IN DETERMINING WHETHER A SEPARATE BRAKING SYSTEMIS RECOMMENDED AND WHAT LIMITS THERE ARE FOR YOUR TOWING COMBINATION AND TRAVELING SAFETY Towing amp braking warning label 32 PRE TRAVEL INFORMATION lt A Do not exceed any applicable motor home weight ratings Doing so could damage your motor home or affect handling and braking characteristics For more information Consult a hitch specialist or your dealer for assistance when preparing your motor home for towing a vehicle or trailer Refer to the Chassis Guide for additional information Motor Home WEIGHT LABELS Vehicle weight labels are posted on Jayco manufactured motor homes so you can make an informed decision before your purchase as to how much cargo capacity is important for you personally The factory installed weight labels are specific to the recreation vehicle for which they are supplied and are not interchangeable Do not remove these labels from your motor home If the labels are missing contact your dealer or Jayco Customer Service for replacements JAYCO INC Dare IL EMELE AF G BY VERPOULE PAUKE PAR Gav PM BG wa PRESS COLD RPL PRIDE GONFIL A TRAD TREPI ANYMNE PaL EPA CAS NL WAI PROS PSG CLI Le TO ee MTP THE YO LO CORP OREES TO ALL APPUCARLE CE WISE COM ORME A TOUTES LOS 11 35 OA Boon VOI LES Ary SS GA LT SONT eS D ATAARE
59. Locking the door helps prevent it from opening unintentionally and keeps intruders from your motor home KEYS Several keys are provided when you purchase your vehicle Most keys have an individual key number stamped on the plate Record these key numbers and keep the information in a safe place You can order a key blank from your dealer to have duplicate keys made If you lose the keys contact your dealer or a locksmith for assistance Make sure the keys are not inside the vehicle before you close and lock the entrance door NOTE Locks on entrance and baggage doors need biannual lubri cation using a light coat of silicone spray Conditions such as rain Salt dust and pollution may increase the maintenance needs DRIVER amp FRONT PASSENGER SEAT Do not adjust the seat while driving After adjusting the seat make sure that it is locked in position To ensure that the seat is locked securely try to move the seat forward or backward without using the adjusting lever or button Do not put packages pets or other objects between the driver s and front passenger co captain s seat 40 VEHICLE OPERATION r SEAT BELTS Legislation in some states may require you to use seat belts but even 1f it is not required a seat belt should always be worn by anyone who drives or rides in this vehicle Never use one seat belt for more than one occupant Never carry more people in the motor home than there are seat belts
60. ON the water pump and allow it to run as needed If the RV water heater has bypass valves A amp B are closed valve Exterior FreshWater C is open refer to the Water Heater Bypass section Disregard Drain if there are no bypass valves Operate the toilet flush lever until water stops flowing 9 Relieve the water pressure using the P amp T valve BEFORE removing the water heater drain plug If there is any water pressure present the water will spray out of the opening when the drain plug is removed When you are finished draining the fresh water system reverse ees these steps and dump the grey and black water holding tanks at an appropriate facility or according to local public codes It is normal for some liquid to remain in the fresh water tank after drainage procedure SANITIZING THE PLUMBING SYSTEM NOTE Refer to the Utility Center section of this manual for details on the utility center settings for sanitizing your system When to sanitize When your motor home is new At the beginning and end of each season When the water system becomes contaminated or every three months of use How to sanitize 1 Level the motor home and drain the fresh water system see Draining the Fresh Water System 2 Water heater power switches 12V GAS amp 120V ELECTRIC at the Command Center should be turned OFF Gas valve at the water heater should be turned OFF Tankl
61. Only connect the shore power cord to properly wired 30 amp NEMA TT30 120 volt power receptacles Do not hook up the power cord to any receptacle until you have verified proper polarity and grounding Polarity indicators can be purchased in most electrical and hardware stores Do not use any cheater plug adapter or extension cord to reconfigure incoming AC power or break the continuity of the circuit connected to the grounding pin Do not connect the power cord into an outlet that is not grounded or adapt the power cord plug to connect it to a receptacle for which it is not designed Do not remove the grounding pin to connect to a non grounded receptacle Removal of the ground pin disables an important safety feature designed to prevent shock and electrocution hazards Do not connect the power cord to an extension cord Use of an improper extension cord will cause overheating of the cord as well as potentially causing premature failure of the AC equipment It is the responsibility of the owner of the electrical receptacle to ensure that the receptacle is properly wired and grounded Reverse polarity and or improper grounding of your RV can cause personal injury or death 120 voLT CIRCUIT BREAKERS The 120 volt AC circuit breakers located inside the Load Center protect all 120 volt wiring and components in the RV from circuit overloads and short circuits Should a circuit overloa
62. Ottawa Ontario KIA ON5 MANUFACTURING PROCESS Jayco recreation vehicles are manufactured for use as temporary living quarters for recreation camping and travel uses all as defined by the bylaws of the Recreation Vehicle Industry Association RVIA ANSI NFPA NO 70 This recreation vehicle is not intended for use as a full time residence or MUST ASSOCIATION for commercial use Commercial use means using the recreation vehicle as a business asset such as a mobile office or using the recreation vehicle for lease or rental purposes Jayco reserves the right to discontinue or change specifications or design at any time without notice and without incurring any obligation whatsoever Recreation vehicles built for sale in Canada may differ to conform to Canadian Codes OPTIONS amp EQUIPMENT The Jayco recreation vehicle is available in several sizes and models so accessories and components may differ slightly between models Some equipment described in this manual may not apply to your vehicle Jayco reserves the right to discontinue or change specifications or design at any time without notice and to make additions or improvements without incurring any obligations upon itself to install these changes on its products previously manufactured Recreation vehicles built for sale in Canada may differ to conform to Canadian Codes WARRANTY amp SERVICE EH ZUL ZUL CUSTOMER RESPONSIBILITY It is important you read and understand all instructions
63. R NOT GCWR CONSULT YOUR OWNER S MANUAL S FOR SPECIFIC WEIGHING INSTRUCTIONS AND TOWING GUIDELINES THE BRAKING CAPACITY OF YOUR MOTORHOME 15 HOT NECESSARILY AS GREAT AS THE TOWING CAPACITY SEPARATE BRAKING SYSTEMS MAY BE NECESSARY FOR CONTROL OF A TOWED VEHICLE AITO TRAILER BOAT ETC BERING THE MOTORHOME IF THE TOWED VEHICLE MEETS OR EXCEEDS THE MINIMUM WEIGHT AS DETERMINED EY THE CHASSIS MANUFACTURER THIS MINIMUM WEIGHT RATING WILL VARY BY CHASSIS AND CHASSIS MANUFAC TURER CON TAG YOUR CHASSIS DEALER OR MANUFACTURER FOR ASSISTANCE IN DETERMINING WHETHER A SEPARATE BAARING SYSTEM IS RECOMMENDED AND WHAT LIMITS THERE ARE FOR YOUR TOWING COMBINATION AND TRAVELING SAFETY Towing and braking label 37 VEHICLE OPERATION Z L_ aAaO OK Total weight of your motor home and any trailer or vehicle towed by it must not exceed the GCWR Do not assume that you can tow a RV that happens to be within the capacity of the tow vehicle hitch By doing so you may exceed the total GCWR of the motor home The total weight of your motor home including cargo passengers fluids etc in addition to the vertical tongue weight must not exceed the GVWR and or any GAWR Once again do not assume that you can tow a trailer or vehicle that happens to be within the vertical tongue weight capacity of the hitch By doing so you may exceed the GVWR and or GAWR of the motor home In addition a separate sup
64. R FUEL TANKS AND OR PROPANE CONTAINERS FAILURE TO COMPLY COULD RESULT IN DEATH OR SERIOUS INJURY Refueling warning label A DANGER Fuel spills represent a serious fire hazard and should be cleaned up immediately Never restart an engine or re light any pilot lights while raw fuel is present 29 FUEL amp PROPANE SYSTEM EE If you spill fuel on the motor home clean it up immediately Fuel can dull or soften paint and damage other surfaces FUEL SAFETY For your protection and others it is critical to understand the danger associated with fuel Take time to become educated about the property of fuel and use it safely A DANGER Automotive fuels can cause serious injury or death if misused or mishandled If you have further questions consult your dealer or Customer Service for assistance Always shut OFF the vehicle engine while refueling Do not bring or store fuel or other flammable liquids inside the motor home because a fire or explosion may result Before refueling extinguish all smoking materials and any open flames Before refueling always turn OFF all spark producing appliances 1 e water heaters furnaces etc Do not overfill the fuel tank s The pressure in an overfilled fuel tank may cause leakage and lead to fuel spray and or fire Fuel spills represent a serious fire hazard and should be cleaned up immediately Never restart an engine or re light any pilot lights while raw fue
65. System Controller A TA E p Se SLIDEOUT SYSTEMS eee Disengage motors manually retract the room and travel lock 6 Locate and remove the motor retention screw which can be found near the top of each vertical column Fig 3 Bend back the wipe seal and visually locate the motor Fig 4 Pull the motor up until it disengages about 1 2 inch 9 Repeat this process for both sides of the slide room 10 Physically push or pull the room back into the opening keep both sides relatively even 11 The room must be travel locked to keep the room in place for road travel DO NOT MOVE THE RV UNLESS THE MOTORS ARE PLUGGED IN TO THE CONTROLLER AND THERE IS BATTERY POWER TO THE RV THIS SETS THE BRAKES ON THE SLIDEOUTS TO PREVENT THEM FROM MOVING DURING TRANSIT Error Codes When an error code occurs during operation the board will use the LEDs lights to indicate where the problem is For motor specific faults the green LED will blink 1 time for motor 1 and 2 times for motor 2 The red LED will blink from 2 to 9 times depending on the error code Error codes are as follows 2times Battery drop out battery capacity low enough to drop below 6 volts while running 3times Low battery voltage is below 8 volts at the start of a cycle 4times High battery voltage is greater than 18 volts 5 times Excessive motor current high amperage also indicated by 1 side of the slide continually stalling 6times Motor short circui
66. Vehicle Weight Rating GVWR we suggest you practice stopping away from traffic until you become 38 VEHICLE OPERATION aaa accustomed to your motor home s stopping distance Your motor home is equipped with a third brake light that activates when the brakes are engaged When descending a long hill drop down into a lower gear or lower range if you have automatic transmission Avoid conditions that require excessive and prolonged use of your brakes Apply and release brakes at short intervals to give them a chance to cool See the chassis owner s manual for additional information The transmission and engine will help in controlling downhill speed and can lengthen brake life The distance required to stop the motor home is greater than an automobile s Use care when accelerating or decelerating on a slippery surface Abrupt speed changes can cause skidding and loss of control Driving through water deep enough to wet the brakes may affect stopping distance or cause the vehicle to pull to one side Check the motor home s brake operation in a safe area to be sure they have not been affected Never operate any vehicle if a difference in braking efficiency is noticeable Your motor home chassis braking system is rated for operation at GVWR not GCWR Whenever possible do not travel with waste in the holding tanks Liquid or debris in the holding tank s may affect the towing characteristics and may result in property damage or pe
67. a siphon To disconnect During the filling process periodically check the fresh water tank level using the Monitor Panel located in the Command Center When the fresh water tank is full it is normal to see water running from the fresh water overflow tubes onto the ground 6 Shut OFF the water pump 7 Disconnect the water hose from the water source and then from the City Water Connection inlet Reinstall the city water connection inlet cap Utility Center Normal Setting Generally speaking this setting allows you to use the water system when dry camping The water pump will circulate water from the fresh water tank to all fixtures in the RV 1 If needed sanitize the water system prior to travel 2 If equipped with a tank storage water heater set the bypass valves to the NORMAL postion supply line valves ON middle valve OFF Tankless water heater will not have bypass valves 3 Turn the appropriate 12 volt GAS or 120 volt ELECTRIC tank storage water heater power switch ON Switches are located on the Monitor Panel On a tankless water 91 PLUMBING SYSTEM RL O 0 heater the power switch is located outside the RV 4 Place the utility center water valves in the Normal position 5 Turn on the water pump make sure you have sufficient 12 volt power 6 Water will be pumped from the fresh water tank to all faucets Sanitize Tank Setting This setting is used to sanitize the fresh water tank When the fresh
68. ack rubber seal are set up correctly The corners of this seal are cut at a 45 angle The top of the seal must overlap the side of the seal to avoid the possibility of water penetration 4 Retracting slideout room Exterior Slideout room Press the IN section of the slideout control switch and hold it corner until the motor stops Operating the switch after the room is fully retracted will damage the switch and motor Maintenance 54 Do not work on your system unless the 12 volt DC auxiliary battery customer supplied and 120 volt AC electrical systems shore line power cord have been disconnected SLIDEOUT SYSTEMS La Your slideout system has been designed to require very little maintenance To ensure a long life of your slideout system read understand and follow these simple instructions This system contains a pre lubed bearing that is lubricated when the room is moved in and out Do not spray oil or grease on the rails while the room is extended TROUBLESHOOTING THE SLIDEOUT If the slideout does not move when the slideout switch is depressed follow these steps Check the auxiliary battery customer supplied for a full charge and good wire connections Check the 12 volt fuse or circuit breaker Check for loose connections at the slideout motor If the slideout still will not operate follow these steps If the slideout is extended refer to the following section on overriding the specifi
69. acles available at most campgrounds The shore power cord is designed to continuously carry the 30 amp current flow required to power each leg of the electrical system It also creates a critical ground connection between the vehicle electrical system and the campground shore power receptacle 61 ELECTRICAL SYSTEM i CONNECTING THE POWER CORD Plugging the shoreline power cord into an incorrectly wired power source could damage the recreation vehicle electrical system and result in severe or fatal injury Always test the external power source 1 e the campsite power receptacle or electrical box with a ground monitor before connecting your power cord to it If the ground monitor indicates reverse polarity or an open ground DO NOT connect the power cord 1 Turn off the load center main 120 volt circuit breaker 2 Carefully extend the entire length of the power cord approximately 25 35 from the electric cable hatch to the external power source 3 Plug the power cord into the receptacle Be sure all the power cord prongs are properly plugged into the receptacle 4 Return to your recreation vehicle and turn on the load center main circuit breaker 5 To help prevent power surges from damaging the connected loads please follow these instructions when hooking up to the external power source The shore line power cord should be unplugged when the recreation vehicle is left unattended If somethin
70. ad capacity is designed by weight not volume so you cannot necessarily use all available space COUNTERTOPS To prevent permanent damage Always use hot pads or trivets under hot pans dishes or heat producing appliances such as frying pans 125 INTERIOR 0000 UU Always use a cutting board never use a knife on the countertop Avoid harsh chemicals such as drain cleaners oven cleaners etc Do not let cleaners with bleach set on the top Wipe them off promptly Laminate countertops if so equipped Glass rings food spills water spots and smudges usually wipe off with a damp sponge Stubborn stains can be removed with a general purpose spray cleaner Some stains can be removed by squeezing fresh lemon juice over the stain and allowing the juice to soak for approximately forty five minutes After 45 minutes sprinkle baking soda over the lemon juice and rub with a soft cloth Solid surface countertops if so equipped Solid surface materials are easy to care for Soapy water ammonia based cleaners not window cleaners as they can leave a waxy build up that may dull the surface or commercially available solid surface cleaners will remove most dirt and residue from all types of finishes A damp cloth followed by a dry towel will remove watermarks Disinfect the surface periodically with diluted household bleach one part water to one part bleach For additional information on the removal of d
71. ages the amperage reguirement 1s greater Check the voltage at the controller If voltage is lower than 11 volts it is recommended that the battery be placed on a charger until it is fully charged It may be possible to jump the RV battery temporarily to extend or retract the room Consult Customer Service before attempting to jump the auxiliary battery Only 1 Side Moving The Schwintek inwall room slide has a separate motor to operate each side of the room Does only 1 side of the room move a short distance 2 to 4 inches and stop Will Non moving side move with help If only 1 side of the room is moving then with another person s assistance press the switch to extend or retract the room while pushing the non moving side in the appropriate direction On larger rooms it may be necessary to have 2 or more people pushing the room Non moving side moved manually Try to push the non moving side in and out If a motorshaft has broken then it will be possible to move that side of the room several inches by hand Larger rooms may require several people to push Debris in the rack Check all 4 gear racks on the side of the room for debris Do the status LEDs light Locate the slide controller for the slideout in question When the room slideout direction switch is actuated do the status LEDs light up Check this in both the extend and retract modes Refer to the Schwintek Slide Room Operation Guide included in your owner s pa
72. all amount of water present in the heat exchanger DOES NOT require the installation of a bypass kit Winterization can be accomplished using one of the two common methods of winterization used for RV water systems The compressed air method or the anti freeze method Refer to Winterization in this section for details Winter Use Device WUD If you wish to operate the water heater in potentially freezing conditions the model GS WH 1M has a built in thermostat that will start the burner whenever the temperature of the Heat Exchanger falls below 38 F and will automatically shut off when it senses a temperature in excess of 58 F IMPORTANT To allow the WUD device to operate you must have sufficient LP Gas in the tank and you must leave the unit powered with the ON OFF switch in the ON position at all times that freezing may occur It will not protect the entire RV s plumbing system The RV must be designed for winter use freezing conditions Pressure Temperature Relief Valve This water heater is equipped with a temperature and pressure relief valve that complies with the standard for Relief Valves and Automatic Gas Shutoff Devices for Hot Water Systems ANSI 721 22 SCALDING INJURY EXPLOSION Valve is not serviceable if defective it must be replaced Tampering with valve will result in scalding injury Do not place a plug or reducing coupling on outlet part of valve If you use a discharge line allow complete dra
73. ane Gas System If so equipped Propane Leak Test Propane label Propane Safety Procedure Propane Gas Container Propane system label ASME Tank Using The Propane System Do not fill to more than 80 label Calculating Propane Gas Usage Cooking With Propane Gas Traveling with Propane Ensure a supply of fresh air Canada units only Cooking comfort heating label Refueling warning label PLUMBING SYSTEM Plumbing System Maintenance Monitor Panel If So Equipped Monitor Panel Fresh Water System Fresh Water Holding Tank 12 Volt Water Pump amp Switch Water Pressure Regulator customer Supplied Water Pump Potable water only label City Fixtures City Fill Tank Country Fill Utility Center Normal Setting Water Purification System If So Equipped Filter housing Sanitize Tank Setting Sanitize Winterize Lines Setting TANK STORAGE WATER HEATER SYSTEM IF SO EQUIPPED Anode rod Replacement chart TANKLESS WATER HEATER If So Equipped Water Heater Bypass Valves If So Equipped TABLE OF CONTENTS Outside Shower If So Equipped 100 Factory installed water heater bypass 100 Faucets 101 Bathroom Tub Shower 101 Hardware Sink or Shower Fixtures 102 Draining The Fresh Water System 102 Sanitizing the Plumbing System 103 Low Point Drain 103 Winterization 105 Black Grey Water System 107 Black Grey Water Holding Tanks 107 Black amp Grey Tank Drains 108 Black Tank Flush If So Equipped 108 Tank Heaters If So Equipped 109 B
74. ar vision camera aids in the use of but does not replace vehicle side rear view mirrors 42 VEHICLE OPERATION Objects in the camera view are closer than they appear When backing up proceed cautiously and be prepared to stop BACKING Up When parking your motor home pick a location that 1s level and back in carefully Check to ensure there are no obstacles in your path and that you have plenty of vehicle clearance Check for low hanging tree limbs posts large rocks or other obstacles Try to choose a parking site that is on the driver s side so you can see what the rear of the motor home is doing With the site on the passenger side you would be backing into the site on your blind side When you determine the site conditions are satisfactory maneuver the motor home into position for backing up into the site space and follow the instructions listed for backing up the motor home in the Chassis Guide NN NOTE Back up the motor home slowly using the outside rearview mirrors along with the rear and side view cameras as aides Have another person outside the motor home assist you until the motor home is parked in the desired position Campsite Hook Up Refer to Electrical System section before connecting the shore line power cord when using full hook up OR before starting the generator if so equipped or operating the vehicle on 12 volt power when dry camping Refer to Fuel amp LP System sec
75. at the top edge of the drape above the driver s and passenger s doors to the corresponding Velcro on the roof of the motorhome cab 5 The Velcro at the bottom corners of the privacy drape under the black plastic hooks should also be attached to the Velcro on the walls of the motorhome in the corresponding locations BED STORAGE Additional storage has been provided under the bed It is equipped with gas struts to assist with easy access To access the storage area grasp the end ledge at the foot of the bed and lift carefully To close carefully push down on the bed slowly easing it to the closed position Before lifting be sure there is nothing on the bed that will restrict its movement or add extra weight Use caution when opening or closing the bed to keep hands and fingers at the end ledge provided not on the side or further back than necessary to avoid pinch points The bedroom electric slide room system may be located under the bed If so it can be accessed by removing the screws holding the wooden paneling in place Use care not to obstruct the slide room system when using the under bed storage area 127 INTERIOR 0000 U D cor ITEMS D cor items such as window treatments day night pleated shades mini blinds and d cor glass should be cared for as follows Window treatments Dust occasionally with a vacuum and soft brush attachment Day Night Roller Shades if so equipped Roller Shades can be easily cared fo
76. ater be drained and bypassed during the winterization process particularly if introducing RV antifreeze into the plumbing system The water heater should never be drained when HOT or UNDER PRESSURE To drain the water heater 1 Turn off electrical power to the water heater either at the switch from the electrical element of at the breaker od PLUMBING SYSTEM E_ O ZUL 2 Shut off the propane supply to the water heater 3 Turn off the water pump 4 Open both hot and cold water faucets 5 Remove the anode rod from the tank For detailed information see the Winterizing The Plumbing System and Water Heater Bypass sections of this manual TANKLESS WATER HEATER If So Equipped Your motor home may be equipped with a tankless water heater The tankless water heater uses up less LP Gas than storage tank model water heaters since it only uses energy when hot water is demanded There is no pilot light to burn when no hot water is needed The tankless water heater supplies an unlimited supply of hot water on demand once lines are purged of standing water As hot water is used the cold water enters the heater A water flow sensor detects the flowing water and automatically ignites the burner Water circulates through the heat exchanger and is heated to the set temperature When the tap is closed the unit shuts down The tankless water heater does not require an anode rod to prevent corrosion or a by pass valve for winteri
77. ayco If NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer or Jayco For additional information please refer to the NHTSA website at www safercar gov 4 WARRANTY amp SERVICE ME JI To contact NHTSA by phone Call the Department of Transportation DOT Vehicle Safety Hotline at 1 888 327 4236 and a NHTSA representative will record your complaint information TTY 1 800 424 9153 or 1 202 484 5238 To contact NHTSA by mail Office of Defects Investigations CRD NVS 216 1200 New Jersey Ave SE Washington DC 20590 In Canada If you believe your recreation vehicle has an alleged safety defect you should contact Transport Canada and Jayco Transport Canada prefers to be called instead of posted mail or email as it enables their investigators to confirm that your information 1s correct and to answer your guestions accurately For additional information please refer to the Transport Canada website at www tc gc ca To contact Transport Canada by phone Call 1 800 333 0510 or 1 613 993 9851 if you are calling from the Ottawa region and ask to speak to a defect investigator To contact Transport Canada by mail Road Safety and Motor Vehicle Regulation Directorate Transport Canada Tower C Place de Ville 330 Sparks Street
78. ayco from any obligation under this warranty and void it By way of example the following shall discharge Jayco from any express or implied warranty obligation to repair or replace any defect that results from any rental or other commercial use or purchase of the RV as defined in this warranty any RV sold outside of or used outside of the United States U S Territories or Canada through an auction or wholesale or by a non authorized dealer any defect in a separately manufactured component part owner neglect or failure to provide routine maintenance See Owner s Manual unauthorized alteration off road use collision or accident whether or not foreseeable including any acts of weather or damage or corrosion due to the environment theft vandalism fire explosions overloading in excess of weight ratings and tampering with any portion of the RV or any use of the RV as a semi permanent or permanent home LEGAL REMEDIES Any action to enforce any portion of this limited warranty or any implied warranty shall be commenced within six 6 months after expiration of the warranty coverage period designated above Any performance of repairs shall not suspend this limitation period from expiring Any performance of repairs after the warranty coverage period has expired or performance of repairs regarding anything excluded from coverage under this limited warranty shall be considered good will repairs and they will not alter the express t
79. ble at the leak point If a leak is indicated shut off the propane system valve s and contact an independent Entegra dealer or qualified propane service representative immediately 79 FUEL amp PROPANE SYSTEM EE A DANGER Fuel spills represent a serious fire hazard and should be cleaned up immediately Never restart an engine or re light any pilot lights while raw fuel is present PROPANE SAFETY PROCEDURE Propane is a colorless and odorless gas that in the liquefied state resembles water An odorant usually a sulfur compound is added as a warning agent If you smell propane within the vehicle quickly and carefully perform the procedure listed on the label below A DANGER IF YOU SMELL PROPANE 1 Extinguish any open flames pilot lights and all smoking materials 2 Shut off the propane supply at the container valve s or propane supply connection Do not touch electrical switches Open doors and other ventilating openings Leave the area until odor clears Have the propane system checked and leakage source corrected before using again a A D o ignition of flammable vapors could lead to a fire or explosion and result death of serious injury Propane system label When propane container is low occasionally there may be a concentration of an onion or garlic like odor which can be mistaken for a propane gas leak After the propane container has been refueled the odor will usually disappear If not turn off
80. ble the RV like the chassis You may contact an independent authorized dealer for details Jayco s obligation to repair or replace defective materials or workmanship is the sole obligation of Jayco under this limited warranty Jayco reserves the right to use new or remanufactured parts of similar quality to complete any work and to make parts and design changes from time to time without notice to anyone Jayco reserves the right to make changes in the design or material of its products without incurring any obligation to incorporate such changes in any product previously manufactured Jayco makes no warranty as to the future performance of this RV and this limited warranty is not intended to extend to the future performance of this RV or any of its materials components or parts In addition the RV owner s obligation to notify Jayco or one of its independent authorized dealers of a claimed defect does not modify any obligation placed on the RV owner to contact Jayco directly when attempting to pursue remedies under state or federal law LIMITATIONS EXCLUSIONS AND DISCLAIMER OF IMPLIED WARRANTIES ANY IMPLIED WARRANTY THAT IS FOUND TO ARISE BY WAY OF STATE OR FEDERAL LAW INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR ANY IMPLIED WARRANTY OF FITNESS IS LIMITED IN DURATION TO THE DURATION SET FORTH IN THIS LIMITED WARRANTY AND IS LIMITED IN SCOPE OF COVERAGE TO THE SCOPE OF COVERAGE OF THIS LIMITED WARRANTY Jayco makes no warrant
81. both 12 volt power and propane gas for full operation Make sure you have sufficient power available before operating your furnace If you have any questions contact your dealer or Customer Service A qualified RV technician should perform all furnace maintenance at least once a year more often depending on furnace usage Never attempt to repair the furnace yourself The furnace should be inspected periodically monthly during the heating season for presence of soot on the vent Soot is formed whenever combustion is incomplete This is a visual warning that the furnace is operating in an unsafe manner If soot is observed on the vent immediately shut the furnace OFF and contact a qualified service agency Operating the furnace under this condition could lead to serious property damage personal injury or loss of life To ensure your personal safety do not obstruct or alter the furnace in any manner Do not install screens over the vent for any reason Screens will become restricted and cause unsafe furnace operation For your safety only the manufacturer s factory authorized parts should be used on your furnace 114 APPLIANCES Microwave IF So EouiPPED Make sure there is sufficient 120 volt power available before operating the microwave NOTE To prevent damage remove the turntable from the micro wave when traveling Never use the microwave cavity for storage The microwave cavity should always be empty when not in use
82. c slideout system installed on your RV If the slideout is retracted leave it in that position Contact your dealer or customer service for repair assistance MANUAL OPERATION Schwintek Inwall slideout system The Schwintek system comes with an electronic manual override In event the slide out does not extend or retract follow these steps to override the system which should allow the slideout to be retracted NOTE Fuses for the slideouts can be found in the load center and may be designated as auxiliary or slideout motor Manual override 1 Locate the slideout system controllers There should be one for each slideout on the recreation vehicle They are typically located in the basement compartment in the forward section of the recreation vehicle either on the forward wall or on the ceiling In some models they may be behind a cargo lined panel 2 The controller that has malfunctioned should have a flashing red LED indicating a hall signal fault will flash 8 or 9 times 3 Press the mode button six times quickly then press a seventh time and hold for approximately 5 seconds 4 The red and green LED s will begin to flash indicating you are in override mode Release the mode button 5 Use either a wall switch or one of the slide room switches located on the command center panel depending on the slideout Press the switch toward the word IN or RETRACT printed next to the sw
83. can circulate freely Keep the area at the back of the refrigerator clean and free of debris Check for obstructions in the exterior refrigerator vent area 1 e spider webs bird nests etc Use a soft cloth to dust off the debris For optimum efficiency and performance it is recommended the refrigerator be checked at least twice a year as part of the routine maintenance Gas electric models If So Equipped 117 APPLIANCES E a a If you smell propane gas STOP Follow the directions located in your manufacturer s owner s manual and in this manual Residential models If So Equipped NOTE If you are using electric to power the refrigerator make sure you are connected to a 120 volt power source The ice maker if so equipped should be turned off and the ice tray emptied when power to your recreation vehicle has been shut off With no power the ice will melt and water may pool in the refrigerator door When power is restored the vibration may cause this water to run out of the door and on to the vehicle floor For detailed operating and safety information refer to the manufacturer s user guide included in the Warranty Packet CLEANING YOUR REFRIGERATOR The following are general cleaning guidelines For detailed information on cleaning your specific refrigerator refer to the manufacturer s user s guide included in the Warranty Packet Cleaning the interior 1 Unplug refrigerator or disconn
84. center to the Sanitize Tank position Turn the water pump ON and sanitizer will be siphoned out of the container and into the fresh water tank Drain valves must be closed to create a siphon To aid siphoning place the container on a flat surface approximately 2 feet off the ground After the recommended amount of sanitizer is in the tank turn the water pump OFF Remove the short hose from the City Water inlet Turn the water valves to the City Fill Tank position Attach a pressurized water source to the City Water inlet Turn on the water source and finish filling the fresh water tank When the water tank is full turn the water source OFF Disconnect the hose from the inlet and the water source Set the water valves to the Normal position Turn the water pump ON Open the hot water line on all the faucets kitchen lavatory shower and outside shower until water begins to flow continuously and a chlorine smell is noticeable Water will not flow until a fixture is opened inside the RV Close the hot water lines and repeat with the cold water lines on the faucets Turn water pump OFF when finished Let the solution remain in the system for at least four hours when disinfecting with 50 PPM residual chlorine If a shorter time period is desired then a 100 PPM chlorine concentration should be permitted to sit in the system for at least one hour For complete fresh water tank sanitization driving your motor home for a short distance will allow
85. chment to remove any loose dirt or debris Fabric if so equipped It is recommended the fabric be professionally cleaned if it becomes stained or soiled The professional cleaner should be made aware the fabrics have been treated to be fire resistant For more information refer to the specific furniture manufacturer s care instructions Ultraleather if so equipped It is recommended the Ultraleather be professionally cleaned if it becomes stained or soiled For more information refer to the specific furniture manufacturer s care instructions Leather if so equipped Periodic vacuuming using a dry cloth to wipe up spills immediately and using a damp cloth on problem areas will help to keep your leather furniture in good condition Leather surfaces can vary as do the cleaning methods Refer to the furniture manufacturer s recommendation or consult a cleaning professional It is recommended you do not use any cleaners containing oils waxes or silicones Cleaners containing silicone can eventually destroy the finish on the leather Cleaners containing oils or waxes should not be used as they leave residues on the surface of the leather which can attract more dirt which can eventually lead to cracking SOFA Hide a bed Sofa or Sofa Sleeper If So Equipped The hide a bed sofa functions much the same as a regular residential hide a bed sofa To make the hide a bed sofa into a bed remove the seat cushions and pull the sofa back
86. cket for further information Call Lippert at 866 524 7821 or visit the Lippert website at www lci1 com for additional troubleshooting information 58 ELECTRICAL SYSTEM 0 THE ELECTRICAL SYSTEM The RV electrical system 1s comprised of two independent electrical systems One operates off of 12 volt DC power and the other off of 120 240 volt 60hz AC power All installations have been made in compliance with industry standards applicable on the date of manufacture Because the electrical eguipment and associated circuitry are engineered into a dedicated system specific to your model we recommend you do not make unauthorized changes or add fixed appliances to it Changes or additions made after delivery may result in a hazardous condition Service and or modification of the electrical system should only be performed by qualified electrical technicians using approved materials components and methods meeting current safety and code requirements Please consult your dealer s service department for assistance To read more about the various components incorporated into the RV electrical system please refer to the component manufacturer s user guide Consult the Chassis Guide for information pertaining to the chassis drivetrain electrical system Electrical System Maintenance Always make sure the inverter charger if so equipped is turned off before disconnecting batteries Always disconnect the shore power cord turn off
87. clears Have the propane system checked and leakage source corrected before using again oun DB 09 Ignition of flammable vapors could lead to a fire or explosion and result death of serious injury Propane system label Fuel Economy Fuel economy depends on many factors Your driving habits can significantly affect your fuel economy Some recommendations for achieving maximum fuel economy are shown Keep your tires inflated to the recommended pressures Keep your motor home tuned up An out of tune engine wastes fuel and costs you money Keep your air cleaner clean and your motor home lubricated according to the recommendations in this manual and the Chassis Guide Do not overload your motor home or tow heavy loads ExnHAust GAs FUMES Avoid inhaling exhaust gases as they contain carbon monoxide which is a potentially toxic gas that is colorless and odorless If you are in a parked motor home with either the engine running or the generator running there is a potential for exhaust fumes to filter back into the motor home 77 FUEL amp PROPANE SYSTEM ELLE OPPOO c 7 EG em To avoid breathing exhaust gases follow these precautions Do not run the engine in confined areas such as a closed garage any longer than needed to move your motor home in or out of the area Windows should be closed while driving or running the generat
88. cord Turn off the inverter if so equipped Disconnect the house batteries main negative battery cable Remove the fuse panel cover to check fuses Pull the fuse straight out of the fuse block If the fuse is not blown something else must be causing the problem Please contact your dealer for further assistance Insert a new fuse of the same specified voltage amperage rating and type in the original location Never use a higher rated replacement fuse The fuse panel label should be kept permanently affixed to your motor home The fuses will not offer complete protection of the motor home electrical system in the event of a power surge or spike Replacement fuses must be of the same voltage amperage rating and type Never use a higher rated replacement fuse doing so may cause a fire by overheating the RV wiring 12 VoLT DC OUTLET There may be multiple 12 volt DC power outlets in your motor home When the 12 volt DC outlet is used as a power source for an electric appliance make sure the appliance operates on 12 volt DC power and that it consumes less than 60 watts 5 amps of power Keep the protective dust cap on the 12 volt DC outlet when not in use to prevent ingestion of foreign material and potential short circuit conditions 65 ELECTRICAL SYSTEM e BATTERIES House Batteries Your motor home has many 12 volt DC loads When combined their total load requires more power than the converter can produce H
89. ct on the paint finish Road Salt and Sodium Chloride Road Tar Bugs Bird Droppings Tree Sap Industrial Fallout Acid Rain Pollution UV Exposure and Moisture The most common problems resulting from these conditions are corrosion staining and chemical spotting Generally the longer the foreign material remains in contact with the exterior finish the more extensive the damage These problems can be minimized by regularly scheduled washing and polishing Wash your recreation vehicle as soon as possible if it becomes contaminated with foreign material Avoid parking under trees or near ocean sea salt Ice or snow should not be scraped from the painted surface Brush off Gravel roads should be avoided Anti freeze gasoline or washer solvents if spilled on the painted surface should be rinsed off with water immediately Bugs and bird droppings should be rinsed off daily Washing Commercial washing should be avoided Wash with cold water using a mild liquid soap Dry wiping with a dry cloth is not recommended Make sure the recreation vehicle s surface temperature is cool under 90 F and out of direct sunlight A shaded area is ideal for washing your vehicle as direct sunlight causes water spotting Use a mild soap or detergent Most auto care stores will carry a car wash shampoo Try to avoid combination wash n wax products as these waxes can cause build up and are designed for smaller surface
90. d FAUCETS Water temperatures over 125 F 49 C can cause severe burns instantly or death from scalds therefore be careful when using hot water Always test the water temperature before showering or washing The faucets operate much the same way as the faucets in your home Make sure there is sufficient water available and if dry camping the 12 volt water pump is turned ON before operating To open the faucets turn the hot and cold knobs ON and adjust the temperature to your comfort level Close the faucets when a sufficient amount of water is released turn the water pump OFF if dry camping BATHROOM TuB SHOWER The shower faucet includes a vacuum breaker for the shower There are two purposes for this breaker To prevent siphoning water through the hose from another fixture To prevent water from being retained in the hose The showerhead DOES NOT have a complete shut off valve the complete shut off is at the faucet The showerhead may drip slightly in the OFF position after use this is normal and 101 PLUMBING SYSTEM E x does not indicate a leak or defect There may be air in the plumbing lines that will need to be bled out before a steady stream of water comes from the faucet The bathing facilities in your recreation vehicle function similar to those in your home Keep the water heater and holding tank capacities in mind when using the fresh water system Long showers are not sugg
91. d The thermostat on your water heater is not adjustable It is a temperature sensing limit designed to maintain a water temperature of 130 F 54 C The water heater does not have a pilot It is equipped with an ignition device which automatically lights the burner Do not try to light the burner by hand Operating instructions 1 Turn OFF all electric power to the water heater 2 Turn OFF the propane supply 3 Wait five minutes for the propane to clear the area If you smell propane STOP Follow the safety instructions listed in the manufacturer s owner s manual If you do not smell propane go to the next step Turn ON the propane supply Turn ON electrical power to the water heater Turn the switch to the ON position If the burner does not light the system will automatically attempt two more tries for ignition before lock out occurs NOTE Each ignition cycle will have a 15 second purge before spark cycle if system is a three try system 7 If lock out occurs before the main burner lights turn the water heater control switch to OFF wait five seconds and turn the switch to the ON position This will restart the ignition cycle 8 The first start up of the heater may require several ignition cycles before all the air is purged form the propane lines If the burner will not come on the following items should be checked before calling a service person 1 See if the switch is turned OFF 2 Check to make sure th
92. d or short circuit occur the circuit breaker protecting the affected circuit will trip preventing the flow of electricity through that circuit If a circuit breaker trips shut off the appliance on that circuit 1 e power converter etc and allow the circuit breaker to cool down for a brief period of time After the cooling down period reset the circuit breaker by moving its lever off and then back to the on position If the circuit breaker re trips or frequently trips contact your dealer to have the electrical problem diagnosed and repaired A circuit breaker identification label 1s permanently attached to the inside surface of the 120 volt Load Center NOTE Load Centers may not always include a main circuit breaker 63 ELECTRICAL SYSTEM e Circuit breakers and fuses will not offer complete protection of the electrical system in the event of power surge or voltage spike Replacement Only replace circuit breakers with those of the same specified type voltage and current rating Never replace a circuit breaker with one listed at a higher amperage rating Please contact your dealer for repair assistance when replacing circuit breakers Replacement circuit breakers must be of the same voltage amperage rating and type Never use a higher rated replacement circuit breaker doing so may cause a fire by overheating the RV wiring Maintenance At the beginning of camping season inspect the
93. d can cause severe damage to the awning and or the RV If wind or extended periods of rain are expected retract the awning It is recommended that if leaving the RV unattended for a length of time retract the awning to avoid unexpected climate conditions Refer to the manufacturer s user guide included in your Warranty Packet for detailed operating and safety information Adjusting the Awning Pitch The longitude arms have 6 pitch adjustment settings from minimum pitch to maximum pitch The awning can be extended and retracted in any of these positions without having to reset the pitch between uses Do not set the individual arm pitch at more than three 3 positions different between the left and right arms Damage to the arms and the canopy can occur if the awning is retracted when the arms are set at more than three 3 positions difference Use care when adjusting the pitch as the awning may move abruptly 50 VEHICLE OPERATION aaa Pitch Adjustment Pins one on each side Support and Lift in this area LG009 1 Hold on to the awning arm to keep it steady while adjusting the pitch Press in the pitch adjustment pins located on the scissor arm TIP Applying LIGHT pressure on the arm will decrease the force required to press the pitch adjustment pins 3 Slide the scissor arm to the desired set hole towards the coach for a lower pitch and away from the coach for a higher pitch Emergency Operati
94. de Please contact your road service provider if applicable or a qualified service facility for assistance Make sure the road service technician reads and is familiar with the information contained in your Chassis Guide regarding emergency towing Never allow anyone to go under the motor home while it is being lifted by towing equipment 44 VEHICLE OPERATION aaa When the unit is being towed be aware of the strap locations Misplaced straps could result in damage to the exterior of your unit Damage resulting from misplaced straps is the responsibility of the towing company and is not covered by the unit warranty FRONT AXLE TIRE ALIGNMENT The term alignment refers to both the adjustment angles on the steering axle and suspension and tracking of the rear axle Many factors are considered when establishing proper alignment Steering components suspension wheel bearings and even proper loading will affect the alignment We recommend you have the front suspension and steering alignment checked and adjusted after you have fully loaded the vehicle according to your needs as part of the vehicle maintenance Thereafter it is your responsibility to have the alignment inspected periodically to maintain vehicle steering performance and prevent uneven tire wear as part of your normal maintenance NOTE Always have the alignment checked and adjusted by a qualified shop with the proper equipment to handle heavy vehicles
95. direct contact and may result in ignition of clothing Proper relationship of pans to burner will improve efficiency During and after use do not touch or let clothing or other flammable material come in contact with the top burners or heating elements burner grates or other areas near the top burners or oven until they have had sufficient time to cool These areas can get hot enough to cause burns Never leave cooking food unattended Turn the pan handles inward but not over the tops of the other range burners Ensure that pans used are large enough to contain the food and avoid boil overs Heavy splattering or spills left on the cook top can ignite and cause burns If using glass glass ceramic ceramic earthenware or other glazed utensils or cookware verify it is safe for use on the top burners Only certain types of utensils or cookware are suitable for surface or top burner use Oven If So Equipped Do not cover the oven vent openings while the oven is in operation Restricting the flow of combustion air will create an asphyxiation hazard The propane gas oven must have 12 volt power to operate If you have any questions contact your dealer or our customer service department Do not use the oven as a storage area 116 APPLIANCES Eee Rance Hoop IF So Equippep If your recreation vehicle is equipped with a range hood it e will be connected to an exterior vent lt lt z The vent has an inner flap with two snap
96. e The AGS system when enabled and with the above conditions met can start and stop the generator according to front air conditioner call to run rear air conditioner call to run coach battery low charge level coach battery charge level prior to camp ground quiet time when AGS is set to quiet time on mode 71 ELECTRICAL SYSTEM BE OA O0 OK ZUL Maintenance With the exception of simple items such as normal maintenance 1 e oil changes etc all service work should be done by a repair facility authorized by the generator OEM Improper adjustments can damage the generator and electrical appliances and can result in a safety hazard If any discrepancy or problem is noted contact your dealer for assistance REPLACING LIGHT BULBS Before replacing a bulb be sure the light is off Do not touch the glass part of the new bulb with your bare fingers The skin oil left on the glass will evaporate when the bulb gets hot the vapor will condense on the reflector and it will dim the surface Replacement light bulbs must be of the type voltage and wattage listed on the lamp fixture Use of incorrectly sized bulbs can overload lam circuits and may create a fire hazard by overheating the fixture COMMAND CENTER The command center is typically a panel located just inside the entrance door or in the living area of the recreation vehicle and contains switches and controls for electrical functions fo
97. e Check wheel lugs Test brakes for proper operation MOTOR HOME STORAGE Properly preparing your motor home for storage during periods of non usage will prevent problems from arising It will also make it easier to get started again for the following camping trip or season To prevent costly freeze ups winterize the plumbing system when it will not be in use for an extended period of time especially if it is stored in colder climates Prepare the chassis for storage in accordance to the Chassis Guide Remember to use fuel additives and supplements if so recommended Wash and wax the exterior of the vehicle Do a sealant inspection and repair as necessary Adding fuel stabilizer to the generator will aid in preventing condensation and fuel varnishing Inspect and clean tires Check for wear cracks and inflation pressure Inspect under the motor home for any openings into the floor where animals or insects may enter and seal if necessary Turn the furnace thermostat s to the OFF position If your motor home is equipped with a gas electric DSI range light a range gas burner to consume any gas remaining in the lines Once the flame extinguishes itself turn the burner valve OFF You may want to place rodent control products in the vehicle during storage Rodents can do damage to the interior components particularly during the winter
98. e By 140 ADDITIONAL INFORMATION SSSEEEEEsss VEHICLE MAINTENANCE RECORD BOLVICE Mileage Work Performed err Notes Date By 141 ADDITIONAL INFORMATION n Notes 142 ADDITIONAL INFORMATION SSSEEEEss Notes 143 ADDITIONAL INFORMATION n Notes 144 ADDITIONAL INFORMATION SSSEEEEss Notes 145
99. e combustion of the burner at these higher altitudes Consult with the local propane company your dealer or the water heater manufacturer for proper derating of the water heater Change out of the orifice derating should be done by the dealer or a qualified service agency A A NOTE It is important that once the motor home has returned to lower elevation below 4500 feet any high altitude deration or other adjustments be reversed for proper operation of the water heater 96 PLUMBING SYSTEM Pressure amp temperature relief valve Do not place a valve between the pressure and temperature P amp T valve and the tank Do not remove or plug the relief valve under any circumstances The temperature and pressure relief valve is designed to open if the temperature of the water within the heater reaches 120 F or if the water pressure in the heater reaches 150 pounds When this pressure is reached the pressure relief valve will open and water will drip from the valve This weeping or dripping will continue until the pressure is reduced to below 150 pounds and the valve closes This condition is normal and does not indicate a defective relief valve One way to reduce the frequency of this occurrence is to maintain an air pocket at the top of the water heater tank This air pocket will form in the tank by design however it will be reduced over time by the everyday use of your water heater To replenish this air pocket
100. e number of times it is pushed When engaged the battery disconnect solenoid supplies battery power to all accessories connected to the house 12 volt fuse panel The battery disconnect feature should be used to disconnect the motor home from house battery power during periods of storage or during maintenance The solenoid must be engaged for the 12 volt house electrical system to operate Never depress the momentary battery disconnect switch for longer than 1 second Depressing and holding the switch down will disable the battery disconnect solenoid Should this occur the main ground cable for the house batteries must be removed for 1 minute to re enable the solenoid operation ISOLATOR SOLENOID When house batteries are installed in parallel circuitry with the chassis battery the charge level in both connected batteries will naturally equalize An isolator solenoid is incorporated to break the connection between the house batteries and the chassis battery when the ignition key is in the off position 67 ELECTRICAL SYSTEM e MII pp O A Ff t Breaking this connection prevents discharge of the chassis battery used to start the engine when using 12 volt devices in the house section of your motor home When the engine 1s running the isolator solenoid engages allowing the house batteries to be charged by the vehicle alternator Always leave the ignition key in the off position unless the engine is running LOAD CENTER
101. e or soft cloth and a mild detergent in warm water For silver accented plastic parts wash with soap or other mild detergents Wipe clean with a sponge or damp cloth Do not use scouring pads powdered cleaners bleach or cleaners containing bleach as these products can scratch and weaken the paint finish WATER HEATER SEE PLUMBING SECTION 119 APPLIANCES E a a Notes 120 ELECTRONICS LA HDTV Anrenna IF So EouiPPED P aaa Light GREEN ON ON 12 volts sent to antenna and KING Jack antenna signal is passed to both TV outputs gn OFF Cable signal is passed to both TV outputs if cable input connected HDTV Antenna Enclosure base amp signal meter Power Injector Your recreation vehicle may be equipped with an exterior amplified high definition TV antenna The antenna comes equipped with a signal meter and a power injector to aid in receiving the strongest possible signal when tuning in HDTV stations NOTE Your RV can be equipped with an antenna that does NOT have the signal strength meter or the power injector This would still have the ceiling enclosure and the knob to turn the antenna Antenna Positioning The knob on the enclosure base inside the recreation vehicle is used to rotate the outdoor roof antenna The arrow on the knob should be pointed towards the TV signal source the TV station Press the button on the side of the knob and turn it to rotate the antenna f
102. e propane supply to the water heater is not empty or turned OFF 3 Check to see if the reset button on the water heater ECO is tripped Water heater bypass If So Equipped Your motor home may be equipped with a water heater bypass This three valve system is located at either the water heater or on the system panel depending on your model For detailed information see the Water Heater Bypass section Odor from the hot water system Many water supplies contain sufficient amounts of sulfur to produce an odor often called sulfur water Sulfur water can be caused by a chemical action or by bacteria Generally sulfur water is not harmful only unpleasant to smell Refer to the water heater manufacturer s owner s manual for details on eliminating the odor from sulfur water Odor from sulfur water is not a service problem 95 PLUMBING SYSTEM E_ O Rpg x Do not replace anode rod or any other component with an accessory part that is not authorized by the water heater manufacturer such as an add on electric heating element Such items are not approved to be installed and could create an unsafe condition and will void all warranties Anode rod protection The tank in the water heater is protected by a magnesium or aluminum anode to prolong the life of the tank by absorbing the corrosive action of hot water Under normal use the anode rod will deteriorate and because of this the water heater OEM recommend
103. eak the smoke alarm will beep about once a minute the low battery warning This low battery warning should last for 30 days but you should replace the battery immediately to continue your protection When the battery is removed from the alarm the battery flag in the compartment will pop up therefore the alarm cannot be installed to the mounting bracket without a battery Only use the replacement battery recommended by the smoke detector manufacturer The smoke detector alarm may not operate properly with other batteries Never use a rechargeable battery as it may not provide a constant charge Never disconnect the battery to silence the alarm Regardless of the manufacturer s suggested battery life you MUST replace the battery once the smoke alarm starts beeping the low battery warning For information on the correct battery and battery installation for your smoke detector refer to the smoke detector user s guide Replacement Smoke alarms have a limited life and are not foolproof Smoke alarms will wear out over time like any appliance Always replace the detector immediately if it is not working properly it displays any type of problem or within five years of use Refer to the smoke detector manufacturer s user guide for additional information COMBINATION CARBON Monox1DE PROPANE ALARM Your recreation vehicle is equipped with a combination carbon monoxide CO propane alarm that is listed for use in recreati
104. ecautions and potential situations which if not avoided may WARRANTY amp SERVICE ZUZ ZUL result in personal injury property damage or damage to your recreation vehicle These precautions are listed in the appropriate areas in this Owner s Manual and in the information contained in the Warranty Packet and on safety labels affixed to your recreation vehicle Read and follow them carefully NOTE Gives helpful information personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death NOTICE Indicates a potential situation that if not avoided may result in property damage or damage to your motor home Q This is the safety alert symbol Itis used to alert you to potential Indicates a potentially hazardous situation that if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices Indicates a potentially hazardous situation that if not avoided may result in death or serious injury A DANGER Indicates an imminently hazardous situation that if not avoided will result in death or serious injury This alert information is limited to the most extreme situations REPORTING SAFETY DEFECTS In the United States If you believe that your recreation vehicle has an alleged defect that could cause a crash or cause injury or death you should immediately inform the National Highway Traffic Safety Administration NHTSA and J
105. ecessary procedures to ensure a safe trip As you develop a routine it is possible that a checklist will be helpful This is a general list which you may want to customize as you determine your own needs Refer to your Chassis Guide for information on chassis maintenance Safety Make sure you follow all safety precautions noted in this owner s manual and in any manufacturer s operators manual when preparing to travel home Interior Close roof vents Close windows amp latch blinds Counter items put away or tied down Furnace turned off Latch drawers cabinets amp doors Lower the TV antenna if applicable Move slideout in and lock it in place if applicable Fasten and secure the furniture for travel if so equipped Refrigerator door locked Set refrigerator to 12 volt if applicable Water heater turned off Water pump turned off Exterior Empty black holding tank rinse as needed 136 TRAVEL CAMPING STORAGE CHECKLISTS LAA Empty gray holding tank Pack equipment into compartments and secure it Lock all exterior compartments Propane turned off if so equipped Retract awning and secure in place Retract step Retract leveling jacks Water hose amp electric cord unhooked and stored Check tire pressure include inner wheel and spare if applicabl
106. ect power 2 Hand wash rinse and dry removable parts and interior surfaces thoroughly Use a clean sponge or soft cloth and a mild detergent in warm water 3 For the inside of the refrigerator use a warm water and baking soda solution consisting of approximately 1 tablespoon 15ml baking soda to 1 quart 1 liter of water This solution both cleans and neutralizes odors Rinse and wipe dry 4 Leave an open box o baking soda in the refrigerator and freezer compartments to help prevent odors XA NOTE Do not use abrasive or harsh cleaners such as window Sprays scouring cleansers flammable fluids cleaning waxes concentrated detergents bleaches or cleansers containing petroleum products on plastic parts interior and door liners or gaskets Do not use paper towels scouring pads or other harsh cleaning tools 118 APPLIANCES SS There is no need for routine condenser cleaning in normal operating environments If the environment is particularly greasy or dusty or if there is significant pet traffic the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency If you need to clean the condenser Remove the base grille Use a vacuum cleaner with a soft brush to clean the grille the open areas behind the grille and the front surface area of the condenser Replace the base grille when finished Cleaning the exterior Wash painted metal exteriors with a clean spong
107. ed to being the most respected name in RVs We invite you to drop by our Visitors Center located in Middlebury Indiana To book a group tour or check our scheduled factory tour times free admission closed holidays please call 1 800 RV JAYCO Asout THis MANUAL This manual is a guide to operation of the features equipment and controls in your motor home If you find components in your motor home vary significantly from what is described please contact your dealer to ensure you have the correct information Nothing in this manual creates any warranty either expressed or implied The only warranty offered is as set forth in the Limited Warranty applicable to the motor home that you received prior to your purchase This Owner s Manual Owner s Portfolio and Chassis Guide are to be considered permanent components of the vehicle and kept in the motor home at all times for personal reference If the motor home is sold they should remain with the vehicle for the next owner Nothing in this manual creates any warranty either expressed or implied nor does it cover every possible detail of equipment standard or option installed on or in your motor home The descriptions illustrations and specifications in this manual reflect the most current available to us at the time of publication are subject to change and are not intended to indicate actual size WARRANTY PACKET There are components that are excluded from the vehicle warranty or are war
108. ed up to 120 volt AC power so the converter operates 53 SLIDEOUT SYSTEMS cc S S gt tt JX t The recreation vehicle must be level and the stabilizer jacks in the extended position Most slideout switches are located on the inside of the recreation vehicle either in the command center panel or on the wall To move the room out press the OUT section of the switch and hold it until the motor stops travel time is approx 25 seconds Operating the switch after the room is fully extended will damage the switch and motor Some models may be eguipped with a wireless remote control to operate the slideout To operate the slideout using the remote press the on off button to power on the remote Select the slideout you want to operate by pressing the corresponding button Next press and hold the extend retract arrow button to move the room in or out When you are finished moving the slideout press the on off button once more to power off the remote DO NOT try and time the end of the stroke by releasing the button early ALWAYS allow the controller to stop both motors before releasing the switch button NN NN NV NA NOTE Do not operate the switch after the room is fully extended as damage can occur to the motor and or switch SLIDEOUT SLIDE ROOM EXTEND RETRACT Slide room switches on Command Center Slideout remote control Slideout Wall Switch After the slideout is extended verify that the corners of the bl
109. eded see ladder capacity label There should never be more than one person on the ladder at the same time SEALANTS Sealants perform a very important function and should be inspected closely and regularly maintained We incorporate many different types of sealants including butyl putty black butyl encapsulated foam silicone clear and colored roof sealant and foam In general sealants do not have set lifetimes Varying environmental factors affect the pliability and adhesiveness of sealants You or your dealer must Inspect all sealants a minimum of every six months A quick walk around the motor home before leaving may help prevent potential problems during trips and vacations Have the sealant replaced if you notice any cracks voids gaps breaks looseness or any sign of physical deterioration Always use the same type of sealant that was removed Your dealer service or parts manager can help you obtain the correct sealant s The sealants may become damaged due to ultraviolet exposure air pollution freezing temperatures and exposure to other elements If deteriorated repair immediately to prevent 132 EXTERIOR MS damage Cap seal all trim and openings at least once after the first year and thereafter as cracks peeling lifting and shrinkage occur Conditions such as rain salt dust and pollution may increase your vehicle maintenance needs To check the exterior sidewall
110. eplaced CHILD SAFETY RESTRAINT SYSTEMS When transporting infants or small children an appropriate child safety restraint system should always be used Follow the manufacturer s instructions for the correct installation and use of these systems NN NOTE All child safety restraint systems should always face the front or rear of the motor home They should never be installed so the occupant is facing the side of the motor home 41 VEHICLE OPERATION OUTSIDE REARVIEW MIRRORS After adjusting the front driver s seat adjust the outside rearview mirrors to your driving preference Have someone help you adjust the mirrors in the desired direction for maximum rear visibility before driving During travel vibration may loosen the fitting holding the mirror s causing them to change position As part of your regular motor home maintenance check and adjust the mirrors to the desired position Power remote mirrors if so equipped You can adjust the power remote mirrors when the ignition key is in the ON position 1 Move the control knob to the side you want to adjust 2 Press the control arrows in the direction you want the mirror to move 3 Return the control knob to the center to lock the mirror s into place The power remote mirrors also contain heating elements to defog or de ice the mirrored glass if needed To activate this feature use the Mirror Heat control located on the driver s side cons
111. equipped with a thermal protection circuit to protect the motor from overheating Operating the awning repeatedly over a short time period may cause the circuit to sense an overheat condition and shut off the motor If this occurs wait approximately 15 minutes to allow the motor to cool then operate the awning in normal fashion The awning seems to extend and retract slowly Normal operation time is 28 35 seconds to extend or retract If the power supply is on the low side of the acceptable voltage range 10VDC 14VDC the awning will move slower If the awning does not operate contact the Carefree Service Center Visit the Carefree website at www carefreeofcolorado com for a listing of dealers and service centers 52 Always operate the awning according to the instructions Periodically check that the fasteners are tight Tighten if necessary Keep the awning fabric and arms clean SLIDEOUT SYSTEMS 0000 ELECTRIC SLIDE Room SYSTEM Make sure the interior slideout room path and the slideout room itself is clear of people and objects before operating Keep away from the slide rails and gear assembly when the room is in motion They may pinch or catch on loose clothing causing personal injury Failure to follow these instructions could result in serious injury or death Make sure the motor home 1s level before operating the slideout room Water leaks and other problems could result if the slideout is operated w
112. eristics If you are dry camping and cannot immediately empty your holding tanks reduce your vehicle speed until you reach a dumping station See Section 4 Vehicle Operation Using The Rear Hitch for important information on how towing a vehicle affects the motor home weight 36 VEHICLE OPERATION a VEHICLE OPERATION You will find that your motor home will travel safely and comfortably at highway speed limits However it will take longer than a passenger automobile to reach that speed Keep this in mind when overtaking and passing another vehicle Allow more time to go around the vehicle you are passing You cannot cut back into the traffic lane as guickly due to the longer length of your motor home Drive with caution to avoid situations that might reguire guick momentum changes The motor home has a longer turning radius than the average automobile When making a turn check the road clearance and be aware of others especially if towing a vehicle behind your motor home Have someone help guide you out of a difficult parking space or traffic pattern Swerves and sharp turns especially at high speeds could result in loss of control of the motor home Adverse weather conditions and extremes in terrain may affect the performance and handling of your vehicle Do not operate the cruise control on icy or extremely wet roads winding roads in heavy traffic or in any other traffic situation where a constant speed cannot be maintained
113. erms of this limited warranty or extend the warranty coverage period or this limitation period In addition this warranty is not intended to extend to future performance and nothing in this warranty or any action of Jayco or any agent of Jayco shall be interpreted as an extension of the warranty period or this limitation period Some states do not allow a reduction in the statute of limitations so this reduction may not apply to you 13 WARRANTY amp SERVICE EHE Z ZUZU WARRANTY REGISTRATIONS Your warranty registration records should be completed and delivered to the manufacturers of component parts The selling dealership will assist you in completing and submitting a delayed warranty start form for your chassis which is included in your chassis paperwork and in filling out the Jayco product warranty registration form That form must be returned to Jayco within ten 10 days of your taking delivery of the RV Your Jayco warranty will not be registered unless this warranty registration is completed and received by Jayco Failure to file this warranty registration with Jayco will not affect your rights under this limited warranty as long as you can present proof of purchase but it can cause delays in obtaining the benefits of this limited warranty and it may inhibit any servicing facility s ability to provide proper repairs and or part replacement CARE AND MAINTENANCE It is the owner s responsibility to perform proper care and mai
114. ess water power switch is located outside the RV 3 Bypass the tank storage water heater if so equipped Set the water heater bypass valves to Bypass middle valve ON supply valves OFF Tankless water heater will not have bypass valves Water heater power should be OFF gas valve to water heater should be OFF also 4 Turn the water valves OFF on each side of the water filter canister Canister is located behind the utility center Unscrew the canister and remove the filter Re attach the empty canister and turn the water valves ON Refer to the Water Purification section 5 Prepare a chlorine solution using 1 4 cup of household bleach sodium hypochlorite 103 PLUMBING SYSTEM EZ_E gt f tft t 0 CK 10 11 12 13 14 15 16 solution to one gallon 3 785 liters of water in a container Prepare one gallon of solution for every 15 gallons of tank capacity This will result in a residual chlorine concentration of 50 ppm in the water system If a 100 ppm concentration is required as discussed in step 13 use 2 cup of household bleach with one gallon of water to prepare the chlorine solution One gallon of the solution should be used for each 15 gallons of tank capacity At the exterior utility center Attach the short hose supplied with the motor home to the city water connection inlet Place the other end of the hose in the container of sanitizer Set the water valves at the utility
115. ested due to the limited amount of water available The used water will drain through the plumbing pipes into the grey water holding tank 1 Be sure the water heater is ON and had sufficient time to heat the water 2 If dry camping be sure your 12 volt water pump is ON 3 Adjust the hot and cold faucets to the desired temperature before bathing 4 To conserve water while showering wet down and turn the water OFF while you use soap then rinse 5 When you are finished shut the water faucets OFF Unlike your home the recreation vehicle does not contain a water pressure balance valve If someone is using the shower it is recommended that the fresh water system NOT BE USED until they are finished Maintenance Read the manufacturer s operator manual or label instructions The tub shower walls if applicable in your recreation vehicle are made of ABS plastic material Use a mild detergent soap and warm water to clean Contact your RV dealer for repair or replacement Do not use gritty or abrasive particle soaps or scouring compound to clean ABS plastic Avoid using Citrus or biodegradable cleaners which contain D Limonene They will damage plastic materials HARDWARE amp SINK OR SHOWER FIXTURES Use mild dish soap and water to clean these fixtures Do not use harsh chemicals or sprays A mild solution of vinegar and water works well to remove hard water spots and stains from the sink or shower fixtures DRAINING THE
116. f vent allows fresh air to circulate through the motor home Do not leave the attic fan open when the motor home 15 stored or unattended for long periods High winds other unusual conditions or obstructions may prevent the dome from closing the resulting leakage could cause non warrantable damage Artic Fan IF So EouIPPED The 12 volt DC attic fan or powered roof vent allows fresh air to circulate through the recreation vehicle Do not leave the attic fan open when the recreation vehicle is stored or unattended for long periods High winds other unusual conditions or obstructions may prevent the dome from closing the resulting leakage could cause non warrantable damage Attic Fan Control The attic fan is controlled with a control pad The dome can be raised or lowered with the UP DOWN buttons and the speed of the fan is controlled by the ARROW buttons It is also equipped with a rain sensor that will close the vent automatically when it rains The rain sensor can be turned on off by holding the DOWN button for 3 seconds For additional information refer to the manufacturer s owner s manual included in your warranty packet THERMOSTAT There may be up to two 12 volt DC thermostats in your motor home Use the controls to set the temperature to your comfort setting 113 HEATING amp COOLING cc o Et J A A A FURNACE The furnace installed in your motor home is controlled by a thermostat The furnace requires
117. f water into the toilet bowl 2 Follow the directions on your approved RV toilet chemical bottle customer supplied by placing the recommended quantity of holding tank chemical into the toilet bowl 3 Flush the toilet and allow at least two gallons 8 liters of water to flow into the holding tank Waste grey holding tank preparation No special preparation is required however placing a small quantity of chemicals into this tank such as baking soda or an approved RV chemical will reduce odors from food particles in the system Cleaning amp Maintenance The toilet should be cleaned regularly for maximum sanitation and operational efficiency Do not use chlorine undiluted or caustic chemicals such as laundry bleach or drain opening types in the toilet system These products damage the seals in toilets and dump valves For more information Refer to the manufacturer s operator manual If you have further questions consult your RV dealer the manufacturer or Customer Service 111 PLUMBING SYSTEM EZ_OE JNE a A T 112 HEATING amp COOLING LAA AIR CONDITIONER Your motor home has a roof mounted air conditioning system that is controlled by a thermostat Cooled air enters the motor home through the adjustable chill grill Make sure you have sufficient power available before operating the air conditioner Do not operate the air conditioner without the return air filter Operating the sy
118. g would happen to the electrical system this may help limit potential damage When you are ready to leave reverse the power cord connection process Use care to prevent damaging the power cord electrical connection pins when connecting or disconnecting the shore line power cord Grasp the plug to remove the power cord from the outlet do not unplug it by pulling on the cord Maintenance Inspect the power cord for cuts cracks and worn insulation Have the power cord replaced immediately if these symptoms are noticed The power cord must be fully extended when in use and not left coiled in the electrical compartment or on the ground If the power cord is left coiled it may potentially create enough heat to melt its protective casing CALCULATING 30 AMP ELECTRICAL Loap IF So EquippPeD When connecting appliances to the electrical system remember that 120 volt power usage is limited to a total of 30 amps Be mindful of the fact that each operating appliance collectively places an added load on your 120 volt electrical system An unintentional trip of a circuit breaker may occur if you overload the motor home and or campground electrical system The amperage rating of individual appliances can be calculated by dividing appliance wattage consumed normally listed on the appliance by 62 ELECTRICAL SYSTEM LAA nominal design voltage 120 for a 120 volt appliance For example 1200 watts divided by 120 volts equals 10 amps
119. his is why a jack and a spare tire have not been included with the motor home Make sure the road service technician reads and is familiar with the Chassis Guide information regarding changing the tires Make sure the wheel lug nuts have been tightened to the proper torque as outlined in your Chassis Guide 48 VEHICLE OPERATION aaa Do not use the hydraulic leveling jack system to support the motor home while under the vehicle or changing tires The hydraulic leveling system is designed as a leveling system only Do not use the hydraulic leveling jack system as a jack or in conjunction with a jack Itis highly recommended that should a tire change be required it be performed by a knowledgeable trained professional Attempts to change tires while supporting the motor home with the hydraulic leveling jack system could result in damage to the motor home and risk causing serious injury or death When replacing a tire make sure to replace it with a tire of the same size and specifications refer to your Chassis Guide for assistance PATIO AWNING Awnings must be closed and locked if applicable while the RV is in transit If weather conditions are windy or stormy close the awning s into the travel mode position Refer to the manufacturer s user guide included in your Warranty Packet for operating and safety information Awning care It is a good idea to keep the awnings in the closed position if you will be away from
120. hwasher cleaning is not recommended Drop In Cooktop IF So Equippep Drop in cooktops add compact high efficiency cooking performance to your recreation vehicle Depending on your model it may be equipped with either a 2 burner or 3 burner cooktop The 2 burner match light cooktop has two 6500 BTU H burners with control panel The 3 115 APPLIANCES EE burner piezo igniter cooktop has one front 9000 BTU H burner and two rear 5200 BTU H burners The 3 burner cooktop is also equipped with a control panel For detailed operating and cleaning information refer to manufacturer s owner s manual KITCHEN STOVE OR RANGE IF So EouiPPED Depending on your model it may be equipped with a 3 burner stove oven combination The match light front burner is 9 000 BTU H and the two match light rear burners are each 6 500 BTU H The top grate is removable for cleaning Refer to manufacturer s manual for detailed operating and cleaning instructions To prevent damage always use the appliance manufacturer s recommended size flat bottom pan s Generally the pan should be large enough to cover the burner but not more than one inch larger than the burner grate Do not use a broiler pan griddle or any other large utensil that covers more than one burner atatime This will create excessive heat that may cause melting sooting or discoloration In addition the use of undersized pans could expose a portion of the heating element to
121. idered discharged at 11 8 volts and dead at 11 65 volts When battery voltage drops below these lower thresholds permanent battery damage may occur Typically a deep cycle battery has an amp hour rating of 75 100 amps If you run the furnace and refrigerator simultaneously you will be using approximately 12 0 3 0 15 0 amps per hour This does not include any 12 volt lights water pump or any other 12 volt component If the furnace and refrigerator in the above example operated constantly a 75 amp hour battery would become fully discharged in 5 hours 75ah 15a 5h Battery storage instructions Some equipment in your motor home will draw small amounts of electrical current even when turned off To prevent house battery discharge when the motor home is not connected to power through the shore power cord it is recommended you shut off the 12 volt battery disconnect solenoid and disconnect the battery negative cable at the house batteries During storage it is important to check battery voltage at least every two weeks and to recharge them as needed If you remove the batteries from your motor home protect them from accidental shorting and keep them in a cool dry well ventilated area 66 ELECTRICAL SYSTEM LAA Always wear eye protection when working with batteries Keep sparks cigarettes and flames away from the battery as the battery may explode Do not use a booster battery or any other power source that has an
122. ifficult stains or surface damage repair refer to the countertop manufacturer s user guide INTERIOR WALL PANEL Please contact your dealership service department for assistance in repairing d cor paneling If deep scratches occur on the wall panel putty sticks can be used to cover scratches on wood surfaces These can be obtained from local hardwood stores and lumberyards To clean use a mild solution of soap and lukewarm water with a soft sponge or cloth Wipe dry with a soft clean cloth Do not use abrasive cleaners as they may cause the vinyl to scratch and become dull Do not use cleaners that contain bleach FLOORING Always test a cleaning agent in an inconspicuous area for colorfastness Carpet Vacuum your carpet regularly It is important to remove loose soil and debris while it is on the surface Heavily traveled areas 1 e walkways areas in front of the furniture may be protected with small throw rugs to prolong the life of the carpet Prompt attention to spots and spills is essential Remove as much of the spill as possible Absorb wet spills as quickly as possible by blotting repeatedly with white paper or cloth towels Refer to the manufacturer s guide included in your Warranty Packet for detailed cleaning information or contact a cleaning professional 126 INTERIOR L Vinyl flooring Periodically vacuum or sweep to remove dirt and gritty particles Although most common spills will not permanently s
123. igh demands for 12 volt power can be met by the house batteries for a limited period of time The 12 volt DC electrical system is designed for usage with Group 27 deep cycle batteries The batteries for the house section of the motorhome are usually referred to as house or coach batteries The house batteries are factory installed to provide temporary 12 volt power when 120 volt power is not available to operate the power converter When drawing energy from the batteries remember that there is a limited amount of power available before the batteries need to be recharged To recharge the house batteries When the engine is running the alternator will automatically charge the house batteries through the auxiliary start solenoid When parked at a campsite and plugged into shore power the power converter will automatically charge the batteries Complete charging may take several hours and depends upon battery condition and the amount of power consumed by the 12 volt devices operated during the charging period Dry camping Consider the charge condition of the house batteries when dry camping When the house batteries are not being recharged and power is being drawn from them they will eventually discharge A battery will discharge faster as its voltage gets lower Plan your 12 volt electrical use accordingly A fully charged 12 volt battery will read 12 7 volts DC and have a specific gravity of 1 265 at 80 F 32 C The house batteries are cons
124. inage for both valve and line Tampering with valve will void the warranty THIS VALVE IS A SAFETY COMPONENT AND MUST NOT BE REMOVED FOR ANY REASON OTHER THAN REPLACEMENT WHEN REPLACING THE PRESSURE TEMPERATURE RELIEF VALVE DO NOT install anything less than a combination pressure temperature relief valve certified by a recognized testing laboratory that conducts periodic inspections of such products and certifies them as meeting the requirements for Relief Valves and Automatic Gas Shutoff Devices for Hot Water Supply Systems ANSI Z21 22 Valve must have a maximum set pressure not to exceed 150 psi Install valve into opening provided and marked for this purpose on water heater Installation must conform with local codes or in the absence of local codes American National Standard for Recreational Vehicles ANSI A119 2 NFPA 501C For more information Refer to the manufacturer s user guide included in your Warranty Packet Maintenance Inspect your water heater monthly and have it serviced at least once a year by the manufacturer s recommended service technician Refer to the manufacturer s owner s manual for detailed inspection and maintenance information If you have further questions contact your RV dealer the manufacturer or Jayco Customer Service 99 PLUMBING SYSTEM E_ E A J0 Water HEATER Bypass VALves IF So EouiPPED Most floor plans have a factor
125. insure protection CHASSIS MAINTENANCE Refer to your Chassis Guide for detailed safety and maintenance instructions EXTERIOR RooF amp SIDEWALL VENTS While you are cleaning the exterior roof assembly also inspect the roof vents including sealants for cracks and keep them clean Inspect the refrigerator and holding tank vents 131 EXTERIOR ZU for blockages from bird nests spider webs leaves etc All exterior access doors and vents need to be kept clean and free of obstructions i e insect nests mud daubers etc while the appliances are in use WINDOWS To avoid exhaust gas entry into the motor home keep windows closed when the chassis or generator engines are running Any ventilating window may permit water inside especially during heavy rainstorms or while driving This is normal and water should only be seen in the lower track portion of the window frame Condensation will also cause water to accumulate on windows and in the tracks Ensure that the escape window latches are properly adjusted the window will pop open if not adjusted tight enough Window glass The window glass can normally be cleaned with a sponge and water Use glass cleaner to remove wax oil grease dead insects etc After washing the glass wipe it dry with a clean soft cloth EXTERIOR LADDER IF So EquippPeD Your motor home is equipped with a rear ladder to allow access to the roof The ladder weight capacity should not be exce
126. interize Lines position The low point drains must be closed for the antifreeze to siphon through the lines 6 Attach the short hose supplied with the motor home to the fresh water connection inlet and insert the other end of the hose into a gallon container of RV antifreeze this quantity should be enough to winterize the motor home To assist the siphoning process put the container on a surface approximately two feet above ground level 7 Turn the water pump ON Ifthe water pump fails to self prime temporarily open the low point drains close the low point drains as soon as the water pump primes RV 105 PLUMBING SYSTEM E_E E ZUL antifreeze will begin draining out and before continuing to the next step 8 Open the hot water line on all the faucets kitchen lavatory shower and outside shower until RV antifreeze begins to flow continuously See instructions below if there is a dishwasher or clothes washer 9 Close the faucet hot water lines and repeat with the cold water lines on all the faucets Do not forget to run RV antifreeze through the toilet See instructions below if there is a dishwasher or clothes washer When you are done adding RV antifreeze 1 Remove the garden hose from the container of RV antifreeze 2 To prevent staining wipe the RV antifreeze out of the sinks shower or tub and toilet using a soft dry cloth If needed contact your RV dealer for assistance Winterizing Dishwasher
127. ion or moisture from condensation inside the RV and failure to provide adequate ventilation mold or any damage caused by mold to the inside or outside of the RV imperfections that do not affect the suitability of the RV for its intended purpose of recreational use or items that are working as designed but that you are unhappy with problems related to misuse mishandling neglect or abuse including failure to maintain the RV in accordance with the owner s manual or other routine maintenance such as inspections lubricating adjustments tightening of screws tightening of lug nuts sealing rotating tires damage due to accident whether or not foreseeable including any acts of weather or damage or corrosion due to the environment theft vandalism fire or other intervening acts not attributable to Jayco service items such as windshield wiper blades lubricants fluids filters etc damage resulting from tire wear or tire failure defacing scratches dents chips on any surface or fabric of the RV damage caused by off road use overloading the RV or alteration of the RV or any of its components or parts In addition this limited warranty does not cover any material component or part of the RV that is warranted by another entity including by way of example handling braking 16 WARRANTY amp SERVICE Eo wheel balance muffler tires tubes batteries gauges generator hydraulic jacks inverter converter microwave television
128. ions This alarm is designed to sense the presence of carbon monoxide propane gas however there are other combustible fumes or vapors that may be detected by the sensor including but not limited to acetone alcohol butane and gasoline These chemicals can be found in commonly used items such as deodorants colognes perfumes adhesives lacquer kerosene glues wine liquor most cleaning agents and the propellants of aerosol cans High temperatures can activate glue and adhesive vapors If you close up the recreation vehicle on a hot day the chemicals used in its construction may be detected for months after the vehicle was constructed for more information refer to Section 2 Formaldehyde What you should do if the alarm sounds Actuation of this detector indicates the presence of carbon monoxide which can kill you Operate the RESET SILENCE button Call your emergency services fire department or 911 Immediately move to fresh air outdoors or by an open door or window ee sidih Do not re enter the premises or move away from the open door or window until the emergency service responders have arrived the premises have been aired out and your alarm remains in its normal condition If your alarm reactivates within a 24 hour period repeat steps 1 4 and call a qualified appliance technician to investigate for sources of carbon monoxide from fuel burning equipment and appliances and inspect for proper operation of this
129. itch and hold it until the unit comes in completely 6 This will allow you to get the recreation vehicle to a service center to have the slideout malfunction diagnosed 55 SLIDEOUT SYSTEMS BB IM ZZL Dual Motor Synchronous Velocity Slide Controller PART 13398 C2 LON PHS 18 NOT AUSER seRVICEABLE FAULT DEVICE E WIN SA 198 Slideout System Controller During this override procedure the motors are not synchronized Visually watch the room and if one side is moving significantly slower than the other or not at all immediately stop and call your dealer or Jayco Customer Service If the system stalls our before reaching end of stroke OR if the room does not close and seal tightly call your dealer or Jayco Customer Service Manually pushing in the slideout 1 56 Locate the slideout system controller refer to previous Step 1 locating the system controllers Unplug motor and motor 2 connectors at the bottom of the slideout controller This releases the motor brakes for each motor The slideout room can now be manually pushed in Larger rooms may require several people to push or pull them Keep both sides of the slideout relatively even while pushing pulling When the room is completely in plug both motor connectors back into the control module This will apply the motor brakes for road travel Dual Motor Synchronous R ntion Velocity Slide Controller MOTOR 1 MOTOR 2 E Slideout
130. ithout leveling the motor home Do not place excessive weight in the slideout room It can cause the slideout room to malfunction and cause damage to the slideout The slideout room system 1s designed for additional floor space and comfort The mechanical components are gear driven Electric powered slideout room systems have a manual override to allow you to extend or retract the slideout room s in case of a power loss Make sure you have sufficient power available before operating your slideout system OPERATING THE SLIDEOUT The Schwintek in wall slideout system is designed to give you the recreation vehicle enthusiast a lifetime of trouble free serecreation vehicleice It requires no maintenance it will never require any adjustments The Schwintek in wall system has two vertical columns a left hand and a right hand Each of these columns has two serpentine gear racks that are attached to the slide room Each side has a drive motor located at the top of the column The right hand and left hand motors remain synchronized by the Dual Motor SynchronousVelocity Slide Controller a circuit board typically located in the basement area of the recreation vehicle Additional support jacks are not needed under the slideout Damage can occur to your slideout room from improper use of aftermarket support jacks 1 The auxiliary battery customer supplied must be fully charged and connected If possible the recreation vehicle should be hook
131. l is present FAILURE TO COMPLY COULD RESULT IN FIRE DEATH OR SERIOUS INJURY Fuel selection Remember the generator is also fueled by the same system used to fuel the chassis engine Check the generator manufacturer and the chassis manufacturer information to help determine the type of fuel best suited for this dual application Fuel filler cap 76 Do not replace the fuel fill cap with one of a different type Only use a cap specified for your motor home Use of a substitute cap may create excessive fuel system pressure resulting in fuel station damage and improper operation in a collision FUEL amp PROPANE SYSTEM LAA Remove the fuel filler cap by slowly turning it counterclockwise and waiting for any hiss noise to stop Then unscrew the cap all the way To close the fuel filler cap securely turn the cap clockwise until you hear clicking sounds Filling the fuel tank If you spill fuel on the motor home clean it up immediately Fuel can dull or soften paint and damage other surfaces Use care when fueling your motor home The following labels if so equipped should be kept permanently affixed to your motor home A DANGER IF YOU SMELL PROPANE 1 Extinguish any open flames pilot lights and all smoking materials 2 Shut off the propane supply at the container valve s or propane supply connection Do not touch electrical switches Open doors and other ventilating openings Leave the area until odor
132. lack Tank Flush Inlet 109 Toilet 110 HEATING amp COOLING Air Conditioner 113 Attic Fan If so equipped 113 Attic Fan If So Equipped 113 Thermostat 113 Attic Fan Control 113 Furnace 114 APPLIANCES Microwave If So Equipped 115 Drop In Cooktop If So Equipped 115 Kitchen Stove or Range If So Equipped 116 Oven If So Equipped 116 Range Hood If So Equipped 117 Cooking With Propane 117 In Case Of A Grease Fire 117 Refrigerator 117 Range Hood Vent 117 Cleaning Your Refrigerator 118 Water Heater See plumbing section 119 ELECTRONICS HDTV Antenna If So Equipped 121 HDTV Antenna 121 Enclosure base amp signal meter 121 Power Injector 121 Exterior Television if so equipped 122 INTERIOR Cleaning The Interior 123 Furniture Upholstery 123 Sofa 123 Hide a bed Sofa or Sofa Sleeper If So Equipped 123 Jack Knife Sofa If So Equipped 123 Trifold Sofa If So Equipped 123 Free Standing Table and Chairs If So Equipped 124 Booth Dinette If So Equipped 124 Cabinetry amp Tables 125 Pantry If So Equipped 125 Countertops 125 TABLE OF CONTENTS Interior Wall Panel 126 Flooring 126 Privacy Drape Installation 127 Bed Storage 127 D cor Items 128 ABS Plastics 128 EXTERIOR Cleaning The Exterior 129 Frame 131 Chassis Maintenance 131 Exterior Roof amp Sidewall Vents 131 Windows 132 Exterior ladder If So Equipped 132 Sealants 132 TRAVEL CAMPING STORAGE CHECKLISTS RV Start Up 135 Ready To Leave Checklist 135 Depar
133. lbourne Seneca Precept Alante If you have any questions regarding this please contact Jayco Customer Service at 800 283 8267 or 574 825 0608 14 WARRANTY amp SERVICE LAA JAYCO TOWABLE RENTAL LIMITED WARRANTY WHAT AND WHO IS COVERED The Jayco warranty covers this recreational vehicle RV when used only for recreational travel and camping including recreational travel and camping by renters of the Dealer for one 1 year This limited warranty applies to the original Dealer only and it is not transferable The warranty period begins on the date that Dealer first places the RV in rental service In the event that a substantial defect in material or workmanship attributable to Jayco is found to exist during the warranty period Jayco will reimburse the Dealer either the reasonable costs of repair or the reasonable costs of replacement of the defect Jayco s option in accordance with the terms conditions and limitations of this limited warranty Jayco s obligation to reimburse Dealer for the reasonable costs of repair or replacement of defective materials or workmanship is the sole obligation of Jayco under this limited warranty Jayco reserves the right to use new or remanufactured parts of similar quality to complete any work and to make parts and design changes from time to time without notice to anyone Jayco reserves the right to make changes in the design or material or its produc
134. leveling jack manufacturer Test all exterior and interior lights Replace any bulbs if they are burnt out Prepare the chassis portion of the motorhome for the camping season in accordance with the Chassis Guide Inspect the tires for wear cracks and inflation pressure Wash the exterior of the motorhome Do a sealant inspection and repair as necessary De winterize and sanitize the fresh water system Connect a towed vehicle to motorhome if applicable and test all connections and lights READY To LEAVE CHECKLIST Following is a preliminary list of items that need to be checked before leaving your home or campsite Check the area under the motor home after overnight parking and look for fuel water oil or other fluid leaks If leaks are detected find the cause and correct it immediately Make sure all fluids are at proper levels Check the engine oil transmission fluid engine coolant power steering fluid and windshield washer fluid Check the fuel gauge and lights on the motor home Have someone observe the operation of all exterior lights while you activate the controls Check the turn signal and high beam indicators on the instrument panel Examine the tires for excessive tread wear or uneven wear patterns Check for stones nails glass or other objects lodged in the tread Inspect for tread cuts or sidewall cracks
135. m the water lines When the water lines are nearly full you may experience some air pockets Allow them to escape before closing the cold water supply faucets 7 The tank storage water heater if so equipped will fill first followed by the supply lines and faucets Tankless water heater does not store water 8 Turn the appropriate 12 volt GAS or 120 volt ELECTRIC tank storage water heater power switch ON Switches are located on the Monitor Panel On a tankless water heater the power switch is located outside the RV To disconnect 9 Shut OFF the water at the external water source 10 Disconnect the non toxic drinking water hose from the water source and then from the City Water Connection inlet Reinstall the city water connection inlet cap City Fill Tank Use this setting to fill the water tank using the city water inlet 1 If needed sanitize the water system prior to travel 2 If equipped with a tank storage water heater set the bypass valves to the NORMAL postion supply line valves ON middle valve OFF Tankless water heater will not have bypass valves 90 PLUMBING SYSTEM oo 3 Remove the City Water Connection inlet cap and attach a non toxic drinking water hose to the City Water Connection inlet at the utility center and the other end to a pressurized water source 4 Place the utility center water valves in the City Fill Tank position 5 Turn ON the water at the external water source
136. malodors and 107 PLUMBING SYSTEM EZ_COE Mt A AZ A help break down holding tank contents unless winterizing Follow the deodorant bottle or package instructions Driving to a disposal site will normally loosen any accumulated waste debris or solids from the sides of the holding tanks Never leave the black tank drain in the open position continuously when connected to the campground sewer system Do not add automotive antifreeze or caustic chemicals such as laundry detergents into the holding tanks Although these products may have a deodorizing effect they may damage the plastic and rubber parts of the plumbing system or the components BLack amp Grey TANK DRAINS The grey tank drain and black tank drain are also referred to as dump valves Always drain the black water holding tank first so the following grey tank waste water can help rinse any solids or debris from the dump outlet and sewer hose To make drainage easier level the motor home Remove the sewer hose housing dust cap and attach the sewer hose Place the end of the sewer hose into the approved dump station Open the black tank dump valve close it when the black water holding tank is emptied Open the grey tank dump valve close it when the grey holding tank is emptied Remove clean and store the sewer hose M 0 a M a Close the sewer hose housing dust cap You can locate many dump stations throughout the United States and Canada in Woodall s
137. matic transfer switch connects the generator to the AC distribution center when the generator is operating and shore power is disconnected When the generator is operating it will power the converter which in turn will charge the house and chassis batteries The generator requires 12 volt power from the house batteries to start and draws fuel from the chassis fuel tank If the fuel tank drops to or below 1 4 full the generator will automatically shut off to keep the motor home from being stranded Be aware the generator when operating gives off carbon monoxide NOTE Be sure to follow the break in procedure outlined in the manufacturers owner s manual 69 ELECTRICAL SYSTEM E Z ZUL Before starting the generator 1 Make sure the carbon monoxide detector is working 2 Turn off air conditioners and all other appliances 3 Check for fuel exhaust and coolant leaks STOP the generator immediately if there is a fuel exhaust or coolant leak and have it repaired CARBON MONOXIDE IS DEADLY Do not run the generator when your motor home is indoors or in a confined space Asphyxiation or carbon monoxide poisoning hazards exist whenever generator exhaust gasses can accumulate Excessive cranking can overheat and damage the generator starter motor Do not crank for more than 20 seconds at a time Wait at least two minutes before trying again If the generator does not start after the third try refer to the generator manufacture
138. mattresses and fabrics the effects of condensation or moisture from condensation inside the RV or failure to provide adequate ventilation mold or any damage caused by mold to the inside or outside of the RV imperfections that do not affect the suitability of the RV for its intended purpose of recreational use or items that are working as designed but that you are unhappy with problems including water leaks related to misuse mishandling neglect or abuse including failure to maintain the RV in accordance with the owner s manual or other routine maintenance such as inspections lubricating adjustments tightening of screws and fittings tightening of lug nuts sealing rotating tires damage due to accident whether or not foreseeable including any acts of weather or damage or corrosion due to the environment theft vandalism fire or other intervening acts not attributable to Jayco service items such 12 WARRANTY amp SERVICE ME JI as windshield wiper blades lubricants fluids filters etc damage resulting from tire wear or tire failure defacing scratches dents chips on any surface or fabric of the RV damage caused by off road use overloading the RV or alteration of the RV or any of its components or parts wheel alignment or adjustments to axles when caused by improper maintenance loading or damage from road hazards including off road travel wheel damage or balancing or damage from tire failures Also any costs associated
139. ment Wheel Lugs Wheel Liners Wheel Bearings amp Brakes Tires Changing A Tire Patio Awning Operating Power Awnings If So Equipped SLIDEOUT SYSTEMS Electric Slide Room System Operating The Slideout Slideout remote control Slide room switches on Command Center Slideout Wall Switch Exterior Slideout room corner Troubleshooting The Slideout MANUAL OPERATION Manual override Slideout System Controller Slideout System Controller Manually pushing in the slideout Disengage motors manually retract the room and travel lock Troubleshooting information ELECTRICAL SYSTEM The Electrical System In Case Of An Electrical Fire Command Center GFCI Receptacle 120 volt 30 AMP AC System If So Equipped Testing the Campsite Power Connection 30 amp Power Cord If So Equipped Connecting The Power Cord Calculating 30 AMP Electrical Load If So Equipped 120 volt Circuit Breakers Inverter If so Equpped Power Converter 12 volt DC System 12 Volt DC Outlet Batteries House Batteries Chassis Battery Auxiliary Start System 12 Volt Battery Disconnect TABLE OF CONTENTS Isolator Solenoid Load Center Approximate Electrical Load Ratings Typical Load Center Exterior Panel 50A Load Center Panel w 120 volt Main breaker Generator Replacing Light Bulbs Command Center Command Center Panel Mounted to wall FUEL amp PROPANE SYSTEM Diesel Fuel amp Fill Refueling warning label Fuel Safety Exhaust Gas Fumes Propane system label Prop
140. months Remove all perishables from the refrigerator freezer Defrost wash and dry the interior of the refrigerator freezer and prop or block the doors open so air can circulate and prevent mildew Remove all perishables from the cabinets Leave the cabinets and doors ajar to allow air circulation and prevent mildew and musty odors Lubricate locks and hinges on exterior doors Turn OFF the motor home 12 volt battery disconnect switch Turn OFF the inverter mode at remote Disconnect the batteries to prevent battery discharge 137 TRAVEL CAMPING STORAGE CHECKLISTS AED LJ T a CCOO While the motor home is being stored If the vehicle is stored outside in areas of heavy snow you should periodically brush the snow off to prevent excessive accumulation and prevent possible roof damage Periodically inspect your motor home during storage and seal off any area that can offer an entry point for rodents birds or insects Also inspect the motor home for any damage Damage from birds rodents insects etc is not covered under the Motorized Transferable Limited Warranty applicable to your motor home 138 ADDITIONAL INFORMATION SSSEEEEEss VEHICLE MAINTENANCE RECORD Make Model Model Year Vehicle Serial Engine ENDID Serial 139 ADDITIONAL INFORMATION n VEHICLE MAINTENANCE RECORD ee Mileage Work Performed a EERO Notes Dat
141. mum load capacity under inflation is just as dangerous as over inflation To insure your tires are operating safely regular inspection of your tires and checking tire pressures is absolutely mandatory Examine your tires frequently for unusual wear Alignment balance and bearing wear will affect tire wear Make sure to look for cracking bulging uneven tread wear etc When you are using your motor home check inflation pressure weekly to insure maximum tire life and travel wear Pressure should be checked when the tires are cold During travel tires heat up and pressure increases Do not bleed air from hot tires or your tires may then be under inflated NOTE Cold tire inflation pressure is defined as a tire that has not been used for three or more hours or has been driven less than one mile Tire inflation pressure of a hot tire may show an increase of as much as 6 psi over a cold tire Tire pressure is the most important factor in the life and performance of your tires Proper inflation should be monitored closely Failure to do so could result in the overheating of a tire which could result in a blowout Inflation pressure should be as recommended by the tire manufacturer or as the federal label for the motor home indicates It is recommended that the tire pressure be checked at the beginning of each trip to obtain the maximum life of the tire Follow the instructions listed on the Federal Certification label to determine the cor
142. n 10 days of when the owner discovered or should have discovered the substantial defect in material or 11 WARRANTY amp SERVICE EHE ZUL ZUL workmanship attributable to Jayco 3 Promptly schedule an appointment with and take the RV to an independent authorized dealer of Jayco or Jayco for repairs and 4 Pay any freight or transportation costs import duties fees and all incidental expenses associated with obtaining warranty service For warranty service simply contact one of Jayco s independent authorized service centers for an appointment and then deliver your RV to the service center on the specified appointment date If you need assistance you may contact Jayco at 903 S Main Street P O Box 460 Middlebury Indiana 46540 Attn Customer Service 574 825 5861 800 283 8267 or www jayco com NOTE Jayco does not control the scheduling of service work at the independent authorized dealerships You may encounter some delay in scheduling or completion of work Also you must notify the selling dealer at time of delivery to have work performed on any defect that occurred at the factory during manufacture at no cost to you as provided by this limited warranty See below under WHAT IS NOT COVERED If two 2 or more service attempts have been made to correct any covered defect that you believe impairs the value use or safety of the RV or if it has taken longer than thirty 30 days for those types of repairs to be com
143. n of a dehumidifier may be required to reduce condensation Check outside extrusions on compartment doors locks slide outs windows vents etc for frozen moisture before operating to avoid damage to parts CONDENSATION Condensation may cause dampness mildew mold staining and if allowed to continue it may result in damage to the recreation vehicle damage caused by condensation is not warrantable It can also lead to mold or mildew issues which could be a health hazard Condensation is a natural phenomenon The amount of condensation will vary with climate conditions particularly the relative humidity Condensation occurs because there is water vapor present in the air which each of us adds to by breathing bathing or cooking The water vapor usually collects on the coolest surfaces When the temperature reaches the dew point the water vapor in the air condenses and changes to a liquid form Proper ventilation and if needed the use of a dehumidifier customer supplied will assist in controlling the condensation Many RV and marine dealers carry small dehumidifiers sized for recreation vehicle use Other suggestions are Crack open windows and roof vents to allow warm moist air to escape When taking a shower open the bath roof vent if so equipped approximately 1 2 allowing the moisture to escape 28 OCCUPANT SAFETY Ea Use the range hood fan if so equipped
144. n vehicle is just as important as washing your vehicle Tap and well water contain many chemicals that could water stain your vehicle s finish We suggest using a damp natural or synthetic chamois There are other drying products such as lint free micro fiber towels that work just as well During cold weather Salt and other chemicals that are spread on winter roads in some geographical areas can have a detrimental effect on the recreation vehicle s underbody If your recreation vehicle is exposed to these conditions spray the underbody with a high pressure hose every time you wash the exterior of your recreation vehicle Take special care to remove mud or other debris that could trap and hold salt or moisture After washing your recreation vehicle wipe off all water drops from the rubber parts around the slideout and doors NOTE When the slideout or door is frozen opening it by force may tear off or crack the rubber gasket that is installed around the slideout or door Therefore pour warm water on the gasket to melt the ice wipe off the water thoroughly after opening the slideout or door To prevent the weather stripping from freezing treat it with a silicone spray Waxing Wax your recreation vehicle once or twice a year or when painted surfaces do not shed water well Use a soft cloth to apply a small amount of wax to the painted surfaces After the wax has dried polish the recreation vehicle with a dry soft cloth Do not wa
145. nd your personal cargo is important for you to know so you do not exceed the Gross Vehicle Weight Rating GVWR of the motor home The volume of space available for storage may exceed the amount of available cargo capacity Large storage compartments have been designed to accommodate normal camping items which are bulky but not necessarily heavy Store items in areas designated for storage Do not store anything in the areas reserved for the converter electrical panels furnace or water heater etc Your recreation vehicle s load capacity is designated by weight not by volume so you cannot necessarily use all available space when loading the vehicle Do not exceed your GVWR and ensure you are loading the vehicle as evenly as you can for the best possible handling Ensure heavy items are secured so they do not shift during travel DO NOT EXCEED YOUR GVWR This means you should weigh your vehicle as loaded for your normal travel to determine the actual weight If you exceed the GVWR you MUST remove items from the motor home or drain liquids then re weigh the vehicle to ensure you have achieved a safe weight Weight labels are posted inside a cabinet door inside all motor homes so you can make a decision before you buy about how much cargo capacity is important for you personally PRE TRAVEL INFORMATION e TRAILER PLUG If you choose to tow behind your RV a chassis manufacturer supplied 7 way trailer plug located at the hitch is
146. ndow s will allow a quick exit from the vehicle during an emergency if access to the main entrance door is not available It is easily identified by the red latches and label Do not remove the following label from your recreation vehicle CALI AD 27W Exit Window Label When parking your recreation vehicle make sure the egress window is not blocked by trees or other obstacles Make sure the ground below the window is solid and can be used as an escape path Practice opening the window before an emergency occurs and make sure all occupants know how to operate it The egress window s must be locked during transit Your recreation vehicle may be equipped with one of the following exit window styles Flip latch style 2 per window Push up on the front lip of the latch and the latch unfolds Push up on the front lip of the latch again to unhook the latch from the window When both latches are released push out on the window which is hinged at the top Exit the vehicle The screen does not need to be removed from the window 19 OCCUPANT SAFETY sc S Et a Slider window latch style Pull the lever down to unlock the window Slide the window to the right to open and exit the vehicle The screen does not need to be removed from the window Lever style latch Remove the screen by pulling the red tab upper right arrow Pull the lever out from the sash clamps Swing the lever out so it is positioned straigh
147. ne These signals indicate immediate action is required Alarm malfunction low battery The gas LED will remain off and the Operational CO LED will alternate re green and the alarm will sound once every 15 seconds End of life alarm The LED will flash red red green green and the alarm will BEEP every 25 30 seconds The alarm should be immediately replaced Maintenance Vacuum the alarm cover at least once a year Clean the cover by hand using a cloth dampened in clean water Dry with a soft cloth Do not spray the front panel of the alarm with cleaning agents or waxes This action may damage the sensor causing an alarm or cause the alarm to malfunction Do not paint the face of the alarm Testing the combination carbon monoxide propane alarm Test the alarm operation after the RV has been in storage before each trip and at least once per week during use The TEST RESET button tests all ELECTRICAL functions of the alarm The TEST Mute switch is located on the front of the alarm Press and hold the test button for 1 second The alarm is working properly if the GREEN indicator light changes color to RED and the horn beeps 4 times The Gas LED should also blink red NOTE Pressing the test button does not check the sensor opera tion Refer to the carbon monoxide propane alarm manufacturers user s manual provided in the Warranty Packet for additional informa tion on testing the sensors 26 OCCUPANT
148. nel marked EXTENDED will light up To retract the stabilizers press and hold the extend retract switch in the retract position The LED light will go off and the stabilizers will retract Turn the power switch OFF If the jacks are down and the vehicle is started and put in gear a loud alarm will begin beeping to let you know the jacks must be retracted EMERGENCY STOPPING Always carry road flares or reflective warning signs to display if necessary Pull off the roadway as far as possible for emergency stopping or tire changing Turn ON your vehicle hazard warning flashers If traveling at night use three red warning indicators such as flares reflectors or lanterns as required by the Uniform Vehicle Code and Model Traffic Ordinance as follows 1 Place the first warning indicator on the traffic side of the recreation vehicle directed at the nearest approaching traffic 2 Place the second warning indicator 100 feet behind the recreation vehicle in the center of the lane and toward approaching traffic 3 Place the third warning indicator 100 feet in front of the recreation vehicle in the center of the lane and away from the traffic approaching from behind N NOTE Curves and or hills may affect the safe placement of warn ing indicators For personal safety always stand off the road and out of the way of traffic EMERGENCY TOWING If your motor home ever needs to be towed refer to the instructions in your Chassis Gui
149. ntenance of the RV and to assure correct load distribution For details regarding this please see your Jayco owner s manual and the owner s manuals of the chassis manufacturer and other component part manufacturers These outline various care and maintenance that is required to maintain your RV Please review all manuals supplied with your RV and contact your selling dealership or supplier of the component part if you have questions Note Failure to maintain the RV as noted in those manuals voids this limited warranty and any damage to the RV as a result of your failure to perform such care is not covered by this limited warranty THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE JAYCO INC 903 S Main Street P O Box 460 Middlebury IN 46540 Telephone 574 825 5861 or 800 283 8267 Notice To Jayco DEALERS This Owner s Manual contains the Towable Limited Warranty that applies to this RV However if the Jayco dealer decides to use this RV for rental purposes then the Towable Limited Warranty will not apply to this RV The Towable Limited Rental Warranty applies in that situation If on the other hand the Jayco dealer sells this RV to a retail customer then the rental warranty would not be applicable The rental warranty does not apply to retail consumers Jayco s rental program is applicable to the following product lines Redhawk Greyhawk Me
150. ole next to the mirror control Adjust the outside rearview mirrors before driving REAR VISION CAMERA Your motor home is equipped with a rear vision monitor that gives a limited televised view of what is behind your motor home The rear vision camera will aid you in backing up the motor home and can be used for a greater field of vision when driving in heavy traffic In addition to the rear vision camera your RV may be equipped with side view cameras as well These will be mounted on each side of the RV facing rearward to give you views down each side of the motor home Check the outside rear view mirrors when driving and backing up the motor home for a more complete field of vision Objects in the camera monitor view can be closer than they appear To become accustomed to using the rear view camera monitor practice backing up in a safe place If in doubt ask another person outside the vehicle to assist The monitor is operational whenever the engine is running To use the monitor flip the switch from standby to ON the monitor will also work when with the motor home is in reverse and the monitor in standby Make sure you turn the monitor to standby while driving to avoid being distracted Never operate the rear vision monitor in the ON position for extended periods of time as this may result in an image burn on the monitor For detailed operating and safety information refer to the manufacturers user guide The re
151. ollowing label is located inside the vehicle near the entry door The label should be left permanently affixed to the recreation vehicle Product in this vehicle may contain formaldehyde which may be an irritant to you You may experience a greater concentration during high humidity and temperatures Ventilate to remove Consult your owner s Formaldehyde label vanual for additional information manu rag dillomal intor ION 0192523 DO NOT REMOVE THIS LABEL 21 OCCUPANT SAFETY us JX ft JK X EXTENDED OR FuLL TIME USAGE Your new recreation vehicle has been built for enjoyment in a recreational manner It1s not intended for use as full time guarters or a permanent residence Continuous living in your vehicle could cause accelerated wear and damage to the various components Continuous or permanent living in your recreation vehicle may affect your warranty coverage and may void the Limited Warranty applicable to your vehicle CoLD WEATHER USAGE When used in freezing or below freezing temperatures the following precautions need to be taken Proper care should be taken with the fresh water and drainage systems to avoid freeze ups Propane gas if so equipped and sufficient power is needed for protection from possible freeze ups on the propane gas regulator Keep in mind that more freguent furnace operation will substantially increase battery draw and propane gas use During cool weather usage ventilation or additio
152. ome cycling may occur depending on the volume of water being released Turn the water pump switch OFF when it is not in use 87 PLUMBING SYSTEM II Pp OO MFf tp N NOTE If there are multiple pump switches the pump must be turned off from the same switch used to turn it on e g if the pump is turned on at the utility center it cannot be turned off with the switch inside the RV at the command center NOTE In some models the water pump switch will be a black rocker Switch located near the sink cabinet The water pump switch should be in the OFF position when the RV is left unattended for any amount of time If something would happen to the water system this may help limit water damage to a smaller area Water pump strainer Water Pump WATER PRESSURE REGULATOR CUSTOMER SUPPLIED Excessive pressure from the water supply source may be encountered in some parks especially in mountain regions when using the fresh water inlet or black tank flush Water pressure regulators are available to protect your recreation vehicles plumbing system against such high pressure A water pressure regulator is recommended to prevent damage to the plumbing system or components To prevent damage when using the city water connection a 45 Ib 315 KPa rated water pressure regulator is recommended 88 PLUMBING SYSTEM LA UTILITY CENTER The following information defines the function of the utility center settings indicated on
153. on If power to the vehicle is not available the awning can be safely retracted by jumping the motor using a 10VDC 14VDC power source such as a cordless drill battery or car battery DO NOT USE A 110VAC POWER SOURCE FOR THE EMERGENCY OVERRIDE PROCEDURE Doing so will permanently damage the awning Do not use the Emergency Override without following the directions below For awnings under 12 feet The arms must be set at an equal pitch Damage to the arms and canopy can occur if the awning is retracted with the arms uneven 1 Remove the front cover The cover snaps onto the rear cover To remove press on both sides of the rear cover until the front cover releases then lift the cover off Detach the RED and BLACK wires from the cable to the motor Attach jumper wires to the motor wires 51 VEHICLE OPERATION 4 Connect the other ends of the jumper leads to the 1OVDC 14VDC Press this area source If the awning moves in the _ to release front cover N wrong direction reverse the leads Maintain contact throughout the retraction process When the awning is closed remove the jumper wires and reattach the cable wires to the motor wires Be sure to match RED to RED and BLACK to BLACK Snap the front cover onto the rear cover Hang the cover on the top and swing it down until it clicks LG010 Additional Awning Operation Information The awning motor is
154. on vehicles The combination carbon monoxide propane alarm will only work if it is operational and maintained 23 OCCUPANT SAFETY E_ O A ta txt The carbon monoxide detector installed 1s intended for use in ordinary indoor locations of recreation vehicles Itis not designed to comply with Occupational Safety and Health Administration OSHA commercial or industrial standards Do not disconnect the battery or the alarm Individuals with medical problems may consider using warning devices that provide audible and visual signals for carbon monoxide concentrations under 30 PPM This alarm will only indicate the presence of carbon monoxide gas at the sensor Carbon monoxide gas may be present in other areas The ultimate responsibility for protection against toxic carbon monoxide fumes rests solely on you Installing a carbon monoxide propane alarm is just the first step in protecting your family from toxic carbon monoxide poisoning The alarm is wired directly to the 12 volt electrical system with continuous power being supplied by the recreation vehicle battery There is no 9 volt battery power supply in the carbon monoxide propane alarm If the battery cable is disconnected at the battery terminals the combination alarm will not work Be sure to read understand and follow the owner s information from the manufacturer of the combination CO propane alarm supplied in your Warranty Packet This includes informa
155. operational and maintained Be sure to read understand and follow the user information provided from the manufacturer of the smoke alarm including information regarding the limited life of smoke alarms Please be aware the smoke alarm cannot detect fires if the smoke does not reach it Anything preventing smoke from reaching the alarm may delay or prevent an alarm 1 e a closed door may prevent smoke from reaching an alarm on the other side of the door etc This smoke alarm will not alert hearing impaired residents Special alarms with flashing strobe lights are recommended for the hearing impaired There are instances when the smoke detector alarm may not be heard Though the alarm horn in this detector meets or exceeds current UL standards it may not be heard for many reasons These include but not limited to a closed or partially closed door the alarm may be drowned out by other noise like the TV stereo traffic weather air conditioner or other appliances Operation The smoke alarm is operational once the battery is correctly installed The LED light will indicate the battery is functioning properly When the production of combustion is sensed the smoke detector sounds a loud alarm that continues until the air is cleared The LED light will also give a visual indication of a sounding alarm How to test Stand at arm s length from the smoke alarm when testing as the alarm horn may be harmful to your hearing The alarm horn
156. or if so equipped to avoid drawing dangerous exhaust gases into the motor home If you suspect that exhaust fumes are entering the passenger compartment have the cause determined and corrected as soon as possible If you must drive under these circumstances close all the windows and adjust the heating or cooling system to force outside air into the motor home set the blower on high speed The best protection against carbon monoxide entry into the motor home is a properly maintained ventilation system and an active carbon monoxide detector To allow for proper operation of the motor home ventilation system keep the ventilation inlet grill s clear of snow leaves or other obstructions at all times Maintenance It is recommended that the exhaust system and vehicle body be inspected by a qualified motor home service center Each time the engine is ready for an oil change Whenever a change in the sound of the exhaust is noticed Whenever the exhaust system underbody or rear of the vehicle is damaged To allow for proper operation of the motor home ventilation system keep the ventilation inlet grill clear of snow leaves or other obstructions at all times For more information refer to your Chassis Guide Propane GAs System IF SO EQUIPPED Propane or LP liquefied petroleum gas is a clean and efficient form of energy when proper handling and safety precautions are observed The propane sys
157. or optimum signal The antenna will rotate a full 360 This antenna is a fixed height 12 and cannot be lowered or raised Trees and foliage will interfere with receiving a strong HDTV signal Power Injector if so equipped The power injector button located on the wall plate switches between your cable satellite signal and the over the air HDTV antenna When the button on the wall plate is pushed in ON it lights green and interrupts the satellite cable input to the TV It then turns on the HDTV roof antenna to receive local TV stations When the button is pushed out OFF it turns the roof antenna OFF and the satellite or cable TV signal is resumed to the TV Signal Strength Meter if so equipped The enclosure base has a built in signal strength meter to aid in obtaining the maximum TV signal A row of LED lights will light up on the face of the enclosure base to indicate signal strength Optimum signal is indicated when the maximum number of LED lights are lit Make sure you have the power injector pushed ON at the wall plate which turns on power to the antenna To turn on the signal strength meter slide the black button on the side of the enclosure base middle photo arrow Next rotate the small attenuator knob on the face of the enclosure base fully clockwise Press the button on the side of the knob and rotate it which rotates the antenna until the maximum number of LEDs light up
158. plemental braking system must be installed if the towed trailer or vehicle meets or exceeds the minimum weight determined by the chassis manufacturer this minimum weight rating will vary by chassis and chassis manufacturer Contact you dealer for assistance in determining whether a separate braking system is recommended for your towing and traveling safety Failure to follow these instructions will Your motor home chassis breaking system is rated for operation at GVWR NOT GCWR Any trailer or vehicle being towed by your motor home must have adequate brakes as required by all state or province and local regulations for towing with your motor home including areas you may be traveling through create a safety hazard and may result in an accident Maintenance Keep the hitch clean along with your general frame maintenance At the beginning of the season and monthly or thereafter clean the inside of the receiver tube with a wire brush and spray with a silicone spray Always remove the utility mount from the receiver when it is not in use This will help prevent the utility mount from rusting to the tube Periodically check the bolts for tightness They need to be torqued to the proper setting refer to your Chassis Guide Refer to the Electrical Systems section for information on the trailer plug BRAKING amp STOPPING Even though your motor home is equipped with brakes designed for its Gross
159. pleted you must to the extent permitted by law notify Jayco directly in writing at the above address of the unsuccessful repair s of the alleged defect s so that Jayco can become directly involved in making sure that you are provided service pursuant to the terms of this limited warranty WHAT IS NOT COVERED By way of example only this limited warranty does not cover any of the following defects in materials components or parts of the RV not attributable to Jayco items that are added or changed after the RV leaves the possession of Jayco additional equipment or accessories installed at any dealership or other place of business or by any other party other than Jayco any RV used for rental or other commercial purposes Note It shall be concluded that the RV has been used for commercial and or business purposes if the RV owner or user files a tax form claiming any business or commercial tax benefit related to the RV or if the RV is purchased registered or titled in a business name any RV sold or used outside the United States U S Territories or Canada any RV not used solely for recreational travel and camping any RV purchased through auction or wholesale any RV purchased from a dealer that is not an authorized dealer of Jayco normal wear tear or usage such as tears punctures soiling mildew fading or discoloration of exterior plastic or fiberglass or soft goods such as upholstery drapes carpet vinyl screens cushions
160. pment vehicle as distributed by Jayco are not covered by the Jayco Limited Warranty The special body company assembler equipment installer or upfitter is solely responsible for warranties on the body or equipment and any alterations or any effect of the alterations to any of the parts components systems or assemblies installed by Jayco Jayco is not responsible for the safety or quality of design features materials or workmanship of any alterations by such suppliers Jayco TRAVEL CLuB All owners of Jayco recreation vehicless are eligible for membership in the Jayco Travel Club The club promotes polarni America family camping and the active use of your RV with others who have similar interests in the RV lifestyle One International Rally is held each year in various locations around the United States and Canada In addition the club offers a variety of local and regional activities throughout the year By belonging to the Jayco Travel Club you will find new ways to enjoy your RV and make friends all across the country For more information please visit www Jaycorvclub com or call 1 800 262 5178 JayPLus EXTENDED SERVICE CONTRACT Don t let unexpected repair costs keep you from traveling toward your dreams Protect yourself with a JayPlus Jay Aus ae Extended Service Agreement For more information contact your dealer or call 1 800 527 3426 Your dealer can help you obtain a JayPlus insurance quote from GMA
161. r s user manual for more information NOTE Refer to the Fuel System section of this manual for detailed information on fuel gauge operation To start the generator manually 1 A remote start stop switch is located inside the recreation vehicle The switch will be located with an hour meter either on a separate panel or on the main monitor panel location will vary by model A second start stop switch is located on the generator 2 Press the operation control switch to start the generator Depending on how cold it is preheat can take up to 15 seconds 3 The hour meter will monitor minutes of usage when the generator is running Before stopping the generator turn off air conditioners and large electrical loads and allow the generator to run 3 to 5 minutes to cool down Flip the red start stop switch to stop For top performance and engine life especially in colder weather let the generator engine warm up for two minutes before connecting turning on appliances 70 ELECTRICAL SYSTEM A CARBON MONOXIDE IS DEADLY MOVING PARTS AND ELECTRICITY can cause severe personal injury or death To reduce exposure to these hazards always disable AGS if so equipped before Sleeping in vehicle unless vehicle has a working CARBON MONOXIDE detector Parking vehicle in garage or confined space Parking vehicle for storage Servicing vehicle for storage Servicing genera
162. r assistance Damaged paint To prevent corrosion touch up small cracks and scratches in the paint coat as soon as possible with touch up film or paint Carefully check the body areas facing the road and the tires for damage to the paint coat caused by flying stones etc To purchase touch up paint use the closest automotive paint available locally match possible Cleaning plastic parts Use a sponge or chamois to clean plastic parts Use warm water and a soft cloth or chamois to remove any white residue from dark colored plastic surfaces Do not use a scrubbing brush other hard tools or wax containing abrasives as they may damage the plastic surface Do not allow plastic to come into contact with brake fluid engine oil grease paint thinner or batter acid These will damage plastic Use a soft cloth and a mild detergent solution to wipe away any such contact Chrome parts To prevent chrome parts from spotting or corroding wash with water dry thoroughly and apply a non abrasive automotive wax If the chrome is severely damaged or pitted use a commercially available chrome polish product FRAME Sand pebbles objects on the highway climate salt air exposure or ice inhibiting chemicals used during the winter months will damage the paint inviting rust and other deterioration Periodically inspect the exterior exposed areas clean and repaint the frame members occasionally and whenever you notice rust or paint chipped away to
163. r by simply using soapy water or a mild cleaning solution on spots However try a small area first Harsh household cleaners or detergents may cause damage to fabric or loss of color Itis our recommendation to dust the rails and fabrics of the shades on a regular basis Mini Blinds if so equipped Dust occasionally with a vacuum and soft brush attachment or venetian blind duster Plastic rails can be cleaned with mild soap and water applied with a soft cloth D cor Glass if so equipped Use a glass cleaner to remove smudges smears and spots If there is any decorative etching on the d cor glass use care when cleaning around that area ABS PLASTICS Dust and wipe clean with soft damp cloth or chamois wiping gently Do not use gritty or abrasive particle soaps or scouring compound to clean ABS plastic Avoid using Citrus or biodegradable cleaners which contain D Limonene as they may damage plastic materials 128 EXTERIOR L CLEANING THE EXTERIOR To protect your recreation vehicle s exterior finish wash it often and thoroughly For recreation vehicles with painted exterior graphics If desired you may wash and wax your vehicle 60 days after purchase The exterior paint does need time to cure before any wax is applied to the exterior surface Careful maintenance for the first 60 days will assure a long lasting durable finish Your recreation vehicle is exposed to many environmental conditions that have an adverse affe
164. r or RV antifreeze Refer to Sanitizing and Winterizing sections 89 PLUMBING SYSTEM E A A 7 Do not remove the following label from your motor home A WARNING POTABLE WATER ONLY SANITIZE FLUSH AND DRAIN BEFORE USING SEE INSTRUCTION MANUAL FAILURE TO COMPLY COULD RESULT IN DEATH OR SERIOUS INJURY AD 04 Potable water only label Label appearance may not be exact The fresh water connection should be unplugged i e the non toxic drinking water hose disconnected when the motor home is unattended for any amount of time If something would happen to the water system this may help limit water damage to a smaller area City Fixtures Use this setting if you are at a campground or other facility where the motor home can be hooked up to an external pressurized water source referred to as city water 1 If needed sanitize the water system prior to travel 2 Move the water heater bypass valves if so equipped to the NORMAL position supply line valves ON middle valve OFF Tankless water heater has no bypass valves 3 Remove the City Water Connection inlet cap and attach a non toxic drinking water hose to the City Water Connection inlet at the utility center and the other end to a pressurized water source Place the utility center water valves in the City Fixtures position Turn ON the water at the external water source Enter the motor home and open the cold water supply faucets to bleed air fro
165. r the RV Depending on your model the command center may be a panel complete with switches or it can be a group of switch pods mounted to a recessed panel inside a cabinet The systems monitor which indicates tank levels and battery charge may be included on this panel Refer to the Monitor Panel section Some models may have the switches controls mounted directly to the wall in the living area or vicinity of the entrance door LAAK Amia ua NA 15 F a Ji 79 noem e ka E ie 1 L Mounted to wall Command Center Panel Command Center Panel W Switch Modules Command Center Panel Typical items found on this panel include may vary depending on model Fuel gauge and hour meter with switches for fuel pump and fuel levels Lighted red pump switch lighted red water heater switches electric amp LP gas Generator start stop switch 72 ELECTRICAL SYSTEM SEs Tank heater switches Light switches for porch lights exterior security lights interior lights awning LED lights front cap LED accent lights Cargo bed red lighted master control switch Slideout control switches press and hold to extend retract Awning control switches press and hold to extend retract Command Center Panel with Switch Modules Items may include separate switch modules and controls that a
166. ranted separately by their own individual manufacturer s limited warranty The Warranty Packet contains these component manufacturer supplied manuals or information sheets warranty cards and or registrations Consult this information for questions regarding operating maintenance servicing instructions and warranty coverage It is important you complete and mail warranty cards and registrations within the prescribed time limits to avoid loss of warranty coverage CHASSIS GUIDE Throughout this manual frequent reference is made to the vehicle s Chassis Guide The Chassis Guide includes the owner s manual provided by the manufacturer of the chassis on which this motor home is built warranty cards and or registrations It also includes pertinent information regarding the transmission tires etc Consult the Chassis Guide for operating safety maintenance servicing instructions and warranty coverage SAFETY ALERTS Throughout this manual certain items are labeled NOTE CAUTION WARNING and DANGER These terms will alert you to precautions that can involve risk to your vehicle or to your personal safety Read and follow them carefully National Safety Associations and organizations require many of the instructions listed Always use the appropriate safety gear when servicing or maintaining your recreation vehicle Please call your dealer or our customer service representatives if you are unsure how to proceed These signal words indicate pr
167. re mounted to a recessed plastic panel Typical items found on this panel include may vary depending on model Systems monitor with LED indicators for tank levels and battery charge status Systems monitor includes lighted red switches for pump and water heater Slideout switches press and hold to retract extend slideouts Light switches for porch lights exterior security lights interior lights awning LED lights power entry step Awning switches press and hold to retract extend awning Auto leveling control panel for leveling the recreation vehicle Inverter panel power switch with display Generator start stop control with hour meter Cargo bed red lighted master control switch Power bunk bed lift control switch Fuel gauge with fuel station on off switch Speaker selector switch Command Center Modules Mounted to the Wall Some RV models will not have the modules in a plastic panel but mounted directly to the wall of the RV Typically these will be located near the entrance door of the RV They may include any of the modules listed above 73 ELECTRICAL SYSTEM LEHE ZZZ ZUL 74 FUEL amp PROPANE SYSTEM PE DIESEL FUEL amp FILL A DANGER Always shut OFF the engine while refueling Do not smoke and do not operate other ignition sources while refueling Do not bring or store fuel or other flammable liguids inside the
168. rect tire pressure A DANGER Failure to follow proper inflation guidelines may result in tire failure which under certain circumstances can cause loss of vehicle control or accidents that may result in property damage bodily injury and or death 47 VEHICLE OPERATION A Tire Wear Diagnostic Chart Wear Pattern Cause Action Adjust pressure to Center Wear Over Inflation particular load per tire catalog Adjust pressure to Edge Wear Under Inflation particular load per tire catalog Make sure load Side W Loss of camber doesn t exceed IOC EESAN or overloading axle rating Align at alignment shop p Check bearing Cupping Out of balance adjustment and balance tires Avoid sudden stop when possible and adjust brakes Wheel lockup amp tire skidding CHANGING A TIRE The motor home is very heavy Raising the motor home to replace the spare tire should only be done with extreme caution by a qualified technician The vehicle could slip causing personal injury or death DO NOT ATTEMPT TO DO THIS YOURSELF If you experience a flat tire on your motor home while driving gradually decrease your vehicle speed if possible Hold the steering wheel firmly and move the motor home to a safe place on the side of the road Please contact your road service provider if applicable or a qualified service facility for assistance Do not attempt to change the spare tire or jack the motor home yourself t
169. rer as the load carrying capacity of a single axle system as measured at the tire to ground interfaces This is the total weight a given axle is capable of carrying GROSS COMBINED WEIGHT RATING GCWR The value specified by the motor home manufacturer as the maximum allowable loaded weight of the motor home in combination with its towed trailer or towed vehicle The tongue weight of a towed vehicle trailer counts as part of the motor home cargo UNLOADED VEHICLE WEIGHT UVW The weight of this motor home as manufactured at the factory with fuel engine oil and coolants and if applicable the weight of a full tank of propane OCCUPANT AND CARGO CARRYING CAPACITY OCCC Is equal to the GVWR of the motor home minus the weight of the motor home as completed at the factory minus the weight of all occupants including the driver minus the weight of all personal cargo minus the weight of a full tank of chassis engine fuel and if applicable minus the weight of a full tank of propane The full weight of potable water including the water heater and the tongue weight of a towed vehicle trailer counts as cargo in or on the motor home Additions to or other changes made to the motor home after it left the factory will affect reduce the OCCC The following labels are located on the inward facing surface of the main entry door of the motor home and on the lower sidewall left of the driver s seat 31 PRE TRAVEL INFORMATION n
170. rn the rod underneath back to the locked position 124 INTERIOR L Make certain the rod underneath the table is in the locked position before putting any weight on the table in the dinette position Injury may occur if it is not locked and the table collapses into the sleeping position with people seated at the dinette Table unlocked Table locked Dinette as a bed CABINETRY amp TABLES To keep hardwood doors cabinet fronts and hardwood tables looking like new regularly dust with a soft cloth dampened with a cleaning polish or mild detergent solution Avoid using ammonia based products or silicone oils as they may cause damage 1f used over a long period of time The finish is durable and resistant to most household spills However spills should be wiped up promptly to avoid potential problems Excessive prolonged exposure to direct sunlight high temperatures and high humidity can cause damage to both the finish and the wood itself These should be avoided Pantry IF So EquipPepD Depending on the kitchen layout of your recreation vehicle you may have a pantry that you can use to store items you wish to take with you as you travel and camp Ensure items stored in the pantry are secured so they do not shift during travel The cabinetry has been designed to accommodate the normal camping items 1 e paper plates flatware cookware etc which are bulky but not necessarily heavy Remember your recreation vehicle s lo
171. rsonal injury PARKING BRAKE The parking brake should be engaged when the motor home is parked Never drive your motor home with the parking brake engaged as this will reduce braking effectiveness and cause excessive driveline wear Refer to your Chassis guide for more information on the parking brake Power ENTRY Door STEP The electric door step opens automatically when the screen door is opened Constant 12 volt power to the electric step is supplied through a circuit breaker generally located inside the battery box near the auxiliary start solenoid When opening the door from the outside make sure you are not obstructing the path of the entrance step Step deployment takes approximately two seconds Keep hands and fingers clear while extending or retracting the entry door step LOOK BEFORE ENTERING OR EXITING YOUR MOTOR HOME 39 VEHICLE OPERATION ENTRANCE Door We have included an assist grab handle at the motor home entrance door The interior portion of the entrance screen door is equipped with a plastic slide panel that allows access to the entrance door handle and locks The entrance door has both a regular door lock and a dead bolt lock Always hold onto the entry door when opening or closing it Damage caused by the entry door catch and holder because you failed to do so is not covered by the Motorized Limited Warranty Make sure the entrance door is completely closed and locked when traveling
172. s Have two dedicated sponges or wash mitts one for the exterior walls and one for the wheels and under carriage Brushes or wash mitts that are made of plastic bristles are acceptable for use on tires and wheel wells but are not intended for use on the exterior walls Avoid using such items on painted surfaces as they will damage the finish Wash the wheels and wheel wells first as this removes heavy dirt and debris and prevents it from splattering on panels Wet the entire area down to remove loose dirt and grime then hand wash one area at a time using your dedicated paint finish sponge or wash mitt Wash from the top and work your way down rinsing frequently to minimize grit abrasion Follow with a final rinse of water This process will remove most contamination from the recreation vehicle s surface For stubborn stains such as road tar or bug stains use an ammonia based glass cleaner or a small amount of rubbing alcohol on a damp cloth followed immediately by warm soapy water and rinsing with clean water This may not dissolve the road tar but it will loosen tar and bug stains and remove them 129 EXTERIOR U from the surface Do not use solvent based cleaners on bird droppings or tree sap as these are water based stains They can be dissolved using ammonia based glass cleaner warm soapy water and a little elbow grease Once again after removing stubborn stains immediately rinse with clean water Drying the recreatio
173. s This flap can be snapped shut when the vehicle is in motion or during storage to keep insects debris snow rain etc from ik entering the recreation vehicle 111 Ps FSII DE Anytime the stove inside the recreation vehicle is being Flap inside a used this flap must_be unsnapped and the range hood Range Hood Vent turned ON to vent fumes outside the vehicle Whenever the stove in the RV is being used The range hood must be turned on and the inner flap must be unsnapped and free to move Failure to do so can create an asphyxiation hazard by restricting air flow to this vent CookInG WITH PROPANE See the Propane System Section for important safety instructions Refer to the manufacturer s owners manual for detailed operating and safety instructions for all propane appliances In Case OF A GREASE FIRE Do not attempt to use water to put out the fire Water can spread some types of fire and electrocution is possible with an electrical fire Grease is flammable Never allow grease to collect around top burners or on the cook top surface Wipe up spills immediately Refer to Section 2 Safety Precautions for fire safety and fire extinguisher information REFRIGERATOR The refrigerator is not intended for quick freezing or cooling We recommend stocking it with pre frozen or pre cooled food when possible The shelves should not be covered with paper or plastic and the food items should be arranged so air
174. s on the propane system and or container after filling Make sure the valve is closed and the compartment door is securely latched When the propane container is disconnected from the main supply hose and the P O L connection install the P O L plastic cap that is attached to the container LP gas container overfill Never allow your propane tank to be filled above the maximum safe level as indicated by the fixed liquid level gauge Do not allow the visible gauge to be used for filling Overfilling the propane container above the liquid capacity indicated on the container could allow liquid propane to enter the system that is designed for vapor only creating a hazardous condition The following warming label has been placed by the propane container 81 FUEL amp PROPANE SYSTEM EE IN WARNING DO NOT FILL CONTAINER S TO MORE THAN 80 PERCENT OF CAPACITY FAILURE TO COMPLY COULD RESULT IN DEATH OR SERIOUS INJURY OVERFILLING THE PROPANE CONTAINER CAN RESULT IN UNCONTROLLED PROPANE FLOW WHICH CAN CAUSE FIRE OR EXPLOSION A PROPERLY FILLED CONTAINER CONTAINS APPROXIMATELY 80 PERCENT OF ITS VOLUME AS LIQUID PROPANE Do not fill to more than 80 label If you suspect your propane container has been overfilled contact your dealer or a qualified propane technician for assistance immediately Do not attempt to service a propane container overfill yourself Refer to your Warranty Packet for more information on the LP ga
175. s system components USING THE PROPANE SYSTEM After your recreation vehicle is completely set up and you are prepared for camping enjoyment use the following steps for propane operation 1 Close ALL burner valves controls and pilot light valves 2 Open the main valve in the propane tank slowly to avoid a fast rush of propane vapor through the excess flow valve causing propane freeze up Should you experience propane freeze up close the main valve and wait 15 minutes before trying again 3 Listen carefully as propane begins to flow If a hissing noise is heard for more than one or two seconds close the main valve and contact your recreation vehicle dealer to have the propane system tested 4 Light the appliances as needed and directed in the appropriate appliance manufacturer s owner manual located in the Warranty Packet Keep the propane container valves closed at all times unless you are using the propane gas system or are having the propane container filled Make sure that you read and fully understand ALL safety requirements for handling and operation of the propane system The Warranty Packet contains manufacturer s user guides for the various appliances hooked to your propane system The propane system provides added benefits to your camping enjoyment however it must be handled with care If you have any questions or concerns consult with your dealer and or the specific manufacturer If you have double
176. s the anode rod be replaced yearly Water with high levels of iron and or sulfate will increase the rate of deterioration therefore more frequent replacements may be required If an anode rod is mostly eaten away replace it with a new one The water heater manufacturer recommends replacement of the anode rod when consumption or weight loss is greater than 75 percent M ov r Anode rod Replacement chart Operating the water heater without the proper anode rod protection will decrease tank life and will void the tank manufacturer s warranty on the tank To extend the anode life drain the water from the water heater tank whenever the motor home 1s not being used Avoid any extended time of non use with water in the tank To prevent a water leak when replacing the anode rod a pipe thread sealant approved for potable water such as Teflon Tape must be applied to the threads of the anode rod Proper application of a thread sealant will not interfere with the anode s function High altitude deration Operation of the water heater at high altitudes may require derating If the water heater is not properly derated lack of sufficient oxygen for combustion may produce improper burner operation Pilot outage caused by burner lift off or sooting from a yellow burner may occur indicating the possibility of carbon monoxide You may also notice a lack of efficiency in heating the water because of incomplet
177. stem without the filter allows the lint and dirt that is normally stopped by the filter to accumulate on the cooling coil of the air conditioner This also will lead to a loss of air volume possible equipment damage and an expensive cleaning process A special foam gasket is placed between the roof material and the subframe of the air conditioner to guard against water leakage The air conditioner is subjected to wind pressures along with motor vibration during normal operation Inspect the mounting bolts for tightness to ensure there is no leakage or looseness at least annually Re tighten bolts when they are loose DO NOT over tighten these bolts as it may damage this gasket The air conditioner gasket is a wearable part that eventually will need to be replaced To gain access to the bolts remove the filtered panel cover on central air systems or the entire air box on non central air conditioners Heat pump operation Set the thermostat for either electric or gas heat On the electric setting the heat pump will become the primary heat source as long as the interior temperature of the RV has not dropped 5 below the thermostat set point If this occurs the thermostat will automatically activate your gas furnace The furnace will continue as the heat source until the thermostat set point has been satisfied At that point the heat pump will again become the primary heat source Attic Fan IF so EQUIPPED The 12 volt DC attic fan or powered roo
178. t motor or wiring to motor has shorted out 8 times Hall signal not present encoder is not providing a signal usually a wiring problem 9 times Hall power short to ground power to encoder has been shorted to ground usually a wiring problem When an error code is present the board needs to be reset Energizing the extend retract switch will reset the board Energize the extend retract switch again to go back to normal operation Troubleshooting information Checking Fuses The Schwintek inwall slide requires a minimum 30 Amp fuse Check the load center for blown fuses and replace any if necessary If the fuse blows immediately upon replacement there is a problem with the wiring to the inwall slide control box A qualified service person should be called to check and repair Obstructions Check outside the recreation vehicle for possible obstructions such as a tree post or car etc Check inside the vehicle for any obstructions such as luggage furniture or open cabinets etc Also check for smaller objects that may be wedged under the floor or in the sides of the unit Remove any obstructions before proceeding 57 SLIDEOUT SYSTEMS c c A hf gt ftX Error Codes Refer to error codes explained previously along with instructions on how to locate the inwall slide controller Low Voltage The Schwintek inwall slide controller is capable of operating the room with as little as 8 volts But at these lower volt
179. t out from the window Push the lever and window out to open and exit the vehicle FIRE SAFETY If a fire does start follow these basic safety rules 1 2 Have everyone evacuate the vehicle immediately After everyone is clear and accounted for check the fire to see if you can attempt to put it out If it is large or the fire is fuel fed get clear of the vehicle and have the Fire Department handle the emergency Do not attempt to use water to put out the fire Water can spread some types of fire and electrocution is possible with an electrical fire Refer to the following sections for additional fire safety information 20 Electrical Systems In case of an electrical fire Appliances In case of a grease fire OCCUPANT SAFETY LA FIRE EXTINGUISHER Fire extinguishers are classified and rated by fire type A B and C These classifications identify the kinds of fires or burning materials they are designed to fight Class A Solid materials such as wood paper cloth rubber and some plastics Class B Liquids such as grease cooking oils gasoline kerosene or other flammable liquids Class C Electrical such as electrical wires or other live electrical equipment A dry chemical fire extinguisher has been installed by the entrance door It is suitable for extinguishing small fires of the Class B or C type only We suggest you become thoroughly familiar with the operating instructions displa
180. t working auxiliary battery not being charged check the reverse polarity fuse s located on the end of the converter There are no customer serviceable parts inside the converter case and the manufacturer s warranty will be void if the case has been removed If you have further concerns contact your dealer 64 ELECTRICAL SYSTEM LAA 12 voLr DC SYSTEM The majority of your motor home lighting is powered by 12 volt electricity The 12 volt DC system is composed of components that will operate when the following conditions are met Power is supplied by the chassis alternator when the chassis engine is running The power converter will supply interior 12 volt DC power when the shore power cord is plugged into a 120 volt external power source The converter will also charge the house batteries in most situations The house batteries power many interior 12 volt components including the lighting fixtures water pump 12 volt motors 12 volt appliances etc when the motorhome is not connected to a 120 volt power source 12 voLT Fuse PANEL The 12 volt fuse panel is labeled to indicate fuse sizes positions and the components powered At the beginning of camping season inspect all the 12 volt fuses and replace as needed Fuses are located in the Load Center Replacing a fuse Before replacing a fuse always turn off the electrical components protected by it 1 2 9 4 5 Disconnect the shore power
181. tain the vinyl floors they are usually easier to remove if wiped up before they set Simply blot with a paper towel and wipe clean with a damp cloth Do not use dish detergents or vinegar and water because they will dull your floor To care for the vinyl floor covering use a damp mop with water and a mild cleaner on the entire floor DO NOT SOAK THE FLOORING Use care to avoid wetting the carpet edges To avoid problems of yellowing linoleum the flooring manufacturer recommends avoiding cleaners that contain oil based solvents i e cleaners containing lemon oil Murphy s Oil Soap etc Privacy DRAPE INSTALLATION Remove the privacy drape from the storage bag which you should find in the storage area under the mattress platform in the bedroom Starting at the driver s side of the cab attach the black plastic hook to the loop attached to the wall behind the driver s seat Make sure that the side of the drape with Velcro is facing the motorhome windshield 1 Pull the drape toward the front of the motor home and behind the driver s side sun visor Open the sun visor against the windshield to hold the drape in place 2 Proceed across the windshield to the passenger side again placing the drape behind the sun visor and opening the sun visor to hold the drape in place 3 Attach the black plastic hook at the passenger s side of the cab to the loop attached to the wall behind the passenger s seat 4 Attach the Velcro
182. te the following C Charge at 12 7 volts G Good at 12 1 volts F Fair at 11 6 volts L Low at 6 0 volts Water pump switch if so equipped The red water pump switch is located on the Monitor Panel the Utility Center or both depending on your model When the water pump switch is ON the water pump will run until it reaches 45 lbs of pressure It will recycle when pressure drops The switch will light up when it is turned ON Turn the switch OFF when the water pump is not being used Water heater switches if so equipped These red switches are located on the Monitor Panel The LP GAS water heater switch 12V enables propane operation of the water heater The ELECTRIC water heater switch 120V enables electric operation of the water heater Normally both switches should be turned on to provide the fastest hot water recovery time The water heater can be operated in electric only or gas only modes by pressing each switch independently The switches will light up when turned ON DSI FLT Direct Spark Ignition Fault if so equipped This light located between the water heater switches will indicate a problem with the LP portion of the water heater When the LP GAS switch is turned on the light will blink quickly 3 times and the water heater will ignite The light will then remain off If the light comes on and stays on it indicates the gas side of the water heater has not fired and there is a problem with the igniter FR
183. tem in your motor home furnishes the fuel for cooking heating hot water and propane generator if so equipped Propane can also be used as an alternative energy source for refrigeration The propane fuel system is comprised of numerous components such as the propane container hoses the propane gas regulator piping and copper tubing lines to each appliance Propane is heavier than air the gas tends to flow to lower areas and will sometimes pocket in these low areas such as the floor Your motor home is equipped with a propane alarm refer to Safety Precautions Combination Carbon Monoxide CO Propane Alarm Propane cylinders should not be placed or stored inside the vehicle LP gas cylinders are equipped with safety devices that relieve pressure by discharging gas into the atmosphere The following label should be kept permanently affixed to the motor home 78 FUEL amp PROPANE SYSTEM i AN DANGER ALL PILOT LIGHTS APPLIANCES AND THEIR IGNITORS SEE OPERATING INSTRUCTIONS SHALL BE TURNED OFF BEFORE REFUELING OF MOTOR FUEL TANKS AND OR PROPANE CONTAINERS FAILURE TO COMPLY COULD RESULT IN DEATH OR SERIOUS INJURY AN WARNING DO NOT FILL PROPANE CONTAINER S TO MORE THAN 80 PERCENT OF CAPACITY FAILURE TO COMPLY COULD RESULT IN DEATH OR SERIOUS INJURY TA A THIS PIPING SYSTEM IS DESIGNED FOR USE WITH PROPANE ONLY DO NOT CONNECT NATURAL GAS TO THIS SYSTEM Securely cap this inlet when not connected for use
184. tentially hazardous situation that if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices 12 VoLrT WATER Pump amp SWITCH When you want to use water in your recreation vehicle and it is not hooked up to city water you will need sufficient 12 volt DC power to run the water pump Once activated the water pump also known as the demand pump will self prime and provide water The pump is designed for intermittent use only Using the pump continuously or with high pressure will shorten the life of the pump and is not covered in your warranty The water pump is engineered with a check valve to prevent water from back flowing into the fresh water supply tank Periodically check the in line water pump strainer for accumulated debris To clean shut off the water pump unscrew the clear cap remove the re useable metal strainer and clear any debris then reinstall For additional information on the care and operation of the pump read the safety and operating information in the pump manufacturer s owner s manual Water Pump Switch if so equipped Most water pump switches illuminate when the water pump is activated In most models the red pump switch is located on the monitor panel or the utility center When the water pump switch is ON the pump runs until 45 lbs of pressure has been achieved The red light will stay on The water pump automatically recycles when pressure drops S
185. the recreation vehicle for an extended period of time Keep your awnings clean and in good condition to prevent costly repairs Periodically check that the fasteners are tight Tighten if necessary Keep the awning fabric clean For detailed cleaning information refer to the manufacturer s owner information included in the Warranty Packet The 12 volt power awning if so equipped may need to be adjusted retracted to operate the entry door some models OPERATING Power Awnincs IF So EouIPPED Your recreation vehicle may be equipped with multiple power awnings each awning will have its own control switch The control switches for the awnings are typically located on the command center switch panel located inside the front entrance door Pressing and holding the switch will extend or retract the awning 49 VEHICLE OPERATION n Carefree LONGITUDE Awnings If So Equipped These awnings if so equipped offer various features that make them easy and convenient to use These features include Scissor style arms do not require vertical ground supports Adjustable arms provide easy to use 6 position pitch adjustment Roller tube and arms are made from light weight no rust aluminum 100 billow proof worm gear driver motor eliminates the need for travel locks Single switch operation 12V motorized awning The effects of wind and rain on an awning are unpredictable an
186. the utility center label City Fixtures This setting allows you to access water at all faucets using city water City Tank Fill This setting allows you to fill your fresh water tank using city water Country Fill This setting allows you to fill your fresh water tank using the 12 volt water pump when you do not have access to city water Normal If the RV is not connected to city water this setting allows you to pump water from the fresh water tank to all faucets using the 12 volt water pump Sanitize Winterize Lines This setting allows you to sanitize or winterize your fresh water system Sanitize Tank This setting allows you to sanitize the fresh water tank The city water connection inlet is located in the utility compartment We recommend that you use a non toxic drinking water hose dedicated only to M supplying the motor home with fresh water to reduce the chance of contamination prevent the non toxic drinking water hose from coming into contact with the ground Install the city water connection inlet cap when the fresh water connection is not being used N NOTE A short hose is supplied with your motor home for use in sanitizing or winterizing the water lines in your RV It can also be used to siphon fill the fresh water tank when no city water is avail able The hose has a fitting that will screw onto the City Water Con nection inlet and the other end can be put into a container of fresh water sanitize
187. the generator disable automatic generator start functionality and disconnect the negative 12 volt DC battery terminal before working on the electrical system Use caution when using metal tools If a tool contacts a battery terminal or metal connected to it a short circuit could occur which could cause personal injury explosion or fire In Case OF AN ELECTRICAL FIRE Do not attempt to use water to put out an electrical fire Water can spread some types of fire and electrocution is possible with an electrical fire Have everyone evacuate the motor home immediately Switch the 120 volt main circuit breaker in the motor home to the off position Disconnect the negative battery cable s at the battery Disconnect the power cord from the shore power receptacle Turn off the generator a er Sy Always have faulty or damaged wiring and electrical components repaired immediately N NN N NOTE It is important that everyone knows where to find the main circuit breaker and how itoperates 59 ELECTRICAL SYSTEM ST eZ Z COMMAND CENTER Your motor home is equipped with a Command Center that allows you to monitor several systems from one location For your convenience the Command Center is located near the kitchen area More information on the controls located in the Command Center will be discussed throughout this manual GFCI RECEPTACLE Grounding is your personal protection from electrical shock
188. the sanitizing solution to splash around all sides of the tank After the required period drain the chlorine solution from the fresh water system see Draining the Fresh Water System Fill the fresh water system using clean potable water until completely full Use the city water connection inlet and a pressurized water source Set the water valves to the City Fill Tank position Then drain and refill the fresh water system one more time see Draining the Fresh Water System If a chlorine taste lingers in the water flush the water system with a solution consisting of one quart vinegar to five gallons of clean water Re flush as necessary Please take note that the Tank storage type water heater must be bypassed and the water filter must be removed prior to flushing your water lines The vinegar solution should be kept out of the water heater and water filter 104 PLUMBING SYSTEM WINTERIZATION Automotive antifreeze ethylene glycol and windshield washer antifreeze methanol are poisonous Never use these products in your fresh water system These products are harmful and may be fatal if swallowed Preparing your motor home for colder weather or storage is very important for most states and Canada Failure to prepare your motor home may cause water supply lines and the water heater to freeze No commodity or product should be added to the fresh water system to ensure freeze protection other than RV antifreeze The
189. the valve s and have the propane system inspected by your dealer or qualified propane service representative This label has been placed in the vehicle near the range for models equipped with a propane system PROPANE GAS CONTAINER Propane is a true gas compressed into a liquid form As the fuel is released from the container it changes to vapor which is then used for the operation of the appliances Propane will not run through the appliances in the liquid state A permanently mounted A S M E approved propane container is located under the floor of the motor home Propane expands 142 percent for every ten degrees of increase in temperature It is imperative to leave sufficient space inside the container to allow for natural expansion of gas during warmer weather 80 FUEL amp PROPANE SYSTEM i FILL 4 1 Propane fill valve 2 Propane gauge ASME Tank Servicing or filling Always shut OFF the engine while refueling Do not smoke and do not operate other ignition sources while refueling Because the container is not removable the motor home will need to be driven to a qualified propane facility for servicing or filling Only the authorized gas service technician s should be near the motor home while the propane tank is being filled The new propane container must be carefully purged for proper appliance performance and operation The propane tank must NEVER BE OVERFILLED Replace all protective covers and cap
190. then STOP and follow the procedures listed in the Propane System Section before attempting to operate the water heater Your motor home may be equipped with either a tank storage water heater or tankless water heater The following is an overview of both systems For detailed operating instructions refer to the manufacturer s owner s manual supplied in your Warranty packet TANK STORAGE WATER HEATER SYSTEM IF SO EQUIPPED Gas Electric DSI Tank Storage Water Heater If So Equipped Your motor home may be equipped with a gas electric DSI direct spark ignite water heater The following is an overview of the water heater operation For detailed operating and safety information refer to the manufacturer s user s guide included in the Owner s Warranty packet Read the safety and operating information provided in the manufacturer s user guide before attempting to activate the water heater Make sure the water heater is filled with water before use even momentary operation of the water heater without water in it may result in damage to the tank and or controls Always open both the hot and cold water faucets when filling the fresh water tank to allow air pockets to be forced out of the water heater The DSI water heater is designed to heat water quickly and efficiently The water heater 94 PLUMBING SYSTEM oo manufacturer has preset the sensing limit to maintain the water temperature when the water heater is activate
191. ting Camp Checklist 136 Motor home Storage 137 ADDITIONAL INFORMATION AN WARNING READ ALL INSTRUCTIONS IN THIS MANUAL AND COMPONENT MANUFACTURER SUPPLIED INFORMATION BEFORE USING YOUR RV This manual has been provided by Jayco for the sole purpose of providing instructions concerning the operation and maintenance of this vehicle and its components Nothing in this manual creates any warranty either expressed or implied The only warranty offered by Jayco is as set forth in the limited warranty applicable to this vehicle The owners failure to provide required service and or maintenance could result in the loss of warranty The owner should review the Jayco limited warranty and the limited warranties that apply to specific components that are offered with this vehicle Instructions are included in the manual for operating various components which are optional on some vehicles or may not be available on your particular model If so equipped does not indicate or imply that the component s or option s were at any time available or can be retrofitted to your model In addition the owner should refer to individual manufacturer s operating instructions contained in the owner s packet WARRANTY amp SERVICE LAA Congratulations Thank you for selecting a Jayco recreation vehicle We are excited to welcome you to our growing RV family Jayco is the largest privately held manufacturer of recreation vehicles in the world We are committ
192. tion before using the LP system Open the LP gas tank valve if so equipped slowly There may be air in the lines and five to thirty seconds of time is needed to bleed air before LP vapor fills the lines Refer to Plumbing Systems section before connecting the fresh water supply or turning ON the water pump or water heater When using full hook up connect the sewer hose to the campsite sewer hook up If applicable start the refrigerator and the cooling or heating system NOTE For extended dry camping management of all your re sources is essential Check your battery levels and conserve battery power use it sparingly ELECTRIC REAR STABILIZER CONTROL IF SO EQUIPPED Your motor home may be equipped with an electrically operated rear stabilizer control The 2 stabilizers are located at the rear of the coach and when extended they will keep the motor home from rocking side to side The control is typically located inside the coach at the stepwell The control has 2 rocker switches one being the power switch and the other extends or retracts the stabilizers 43 VEHICLE OPERATION L CC ZUZ ZUL To use the system press the power switch to the ON position To extend the stabilizers press and hold the extend retract switch in the extend position until the stabilizers are fully extended When they are fully extended the LED light at the bottom of the pa
193. tion regarding the limited life of the alarm Carbon monoxide CO is an insidious poison It is a colorless odorless and tasteless gas Many cases of reported carbon monoxide poisoning indicate while victims are aware they are not feeling well they become so disoriented they are unable to save themselves by either exiting the vehicle or calling for assistance Young children and household pets may be the first affected The following symptoms are related to carbon monoxide poisoning and should be discussed with all members of the household Mild exposure Slight headache nausea vomiting fatigue often described as flu like symptoms Medium exposure Severe throbbing headaches drowsiness confusion fast heart rate Extreme exposure Unconsciousness convulsions cardio respiratory failure death 24 OCCUPANT SAFETY Ea Your combination carbon monoxide propane alarm is designed to detect the toxic carbon monoxide fumes that result from incomplete combustion such as those emitted from appliances furnaces fireplaces and auto exhaust A carbon monoxide propane alarm is NOT A SUBSTITUTE for other combustible gas fire or smoke alarms This carbon monoxide alarm is designed to detect carbon monoxide gas from ANY source of combustion It is not designed to detect smoke fire or any other gas Please note that there are hazards against which carbon monoxide detection may not be effective such as natural gas leaks or explos
194. tion system if so equipped The waste water system consists of the waste water holding tank sewage holding tank drains and toilet PLUMBING SYSTEM MAINTENANCE Check all fittings pressure and waste for leaks before each trip or before vehicle storage as part of your normal maintenance Inspect all faucets the water purification system optional and sink connections including drain baskets or filters Inspect connections at the water pump and water heater At the end of every trip you should drain any unused water from the fresh water system The fresh water or potable water system needs periodic sanitization and winterization to take care of all the components within the plumbing system and help discourage the growth of bacteria and other organisms that can contaminate the water supply There are labels affixed to the exterior of the recreation vehicle sidewall that indicate the locations of the water system drains and fills Be aware some drain valves may be located inside the vehicle once the exterior label is found go inside to find the drain corresponding location MoniTorR PANEL IF So EquipPep The interior wall mounted Monitor Panel allows you to monitor the fresh water grey water black water and auxiliary battery levels These functions are controlled using the tact switches located on the monitor panel faceplate The Monitor Panel operates on 12
195. to operate Generally more water is required only when flushing solids Prior to using the sanitation system it is strongly recommended to flush the toilet several times to release sufficient water into the holding tank If there is not a sufficient amount of water used during flushing the waste materials may not evacuate properly from the drain line to the tank Clogged tanks and pipes could eventually occur The toilet system will perform better when water is run for ten to fifteen seconds after flushing to ensure that the waste will proceed to the bottom of the tank Unlike a toilet in a home which may use up to seven gallons of water per flush the average recreation vehicle system uses one to three quarts 1 3 liters For added convenience and better sanitation system performance it is advisable to always have four to six inches 10 15 cm of water in the toilet It is important to prevent solid waste buildup Follow the toilet manufacturer s recommended instructions each time after emptying the black water holding tank It is important to add enough water to prevent solid waste buildup Follow the directions listed below and in the manufacturer s operator manual 110 PLUMBING SYSTEM It is important to add enough water to prevent solid waste buildup Follow the directions listed below and in the manufacturer s operator manual Sewege black tank preparation 1 Release one to two quarts 1 or 2 liters o
196. tor Servicing batteries Servicing appliances or electrical systems Fueling the vehicle DO NOT run the generator or use the AGS AUTO ON or QUIET ON modes if so equipped when your RV is indoors or in a confined space Asphyxiation or carbon monoxide poisoning hazards exist whenever generator exhaust gasses can accumulate Automatic Generator Start AGS system If So Equipped When enabled the AGS system will automatically start and stop the generator according to operator or factory selected parameters It can also be used as a manual generator start stop switch AGS is typically used on motorhomes 1 The AGS system has been setup and tested using default values for the factory installed generator Consult the manufacturer s manual for operator programming information The AGS system 1s enabled by pressing the AUTO GEN key followed by pressing the ENTER key on the face of the Energy Command control panel The AGS system will not operate unless the battery disconnect switch is on The factory installed AGS system will not start the generator when shore power is connected to the motor home If shore power is connected to the motor home when the AGS has started the generator the generator will stop The AGS system as installed will be disabled anytime the chassis ignition key is cycled to either the on or off position The AGS may be manually re enabled after an ignition key cycl
197. ts without incurring any obligation to incorporate such changes in any product previously manufactured Jayco makes no warranty as to the future performance of this RV and this limited warranty is not intended to extend to the future performance of this RV or any of its materials components or parts In addition the Dealer s obligation to notify Jayco of a claimed defect does not modify any obligation placed on the Dealer to contact Jayco directly when attempting to pursue remedies under state or federal law LIMITATIONS EXCLUSIONS AND DISCLAIMER OF IMPLIED WARRANTIES ANY IMPLIED WARRANTY THAT IS FOUND TO ARISE BY WAY OF STATE OR FEDERAL LAW INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR ANY IMPLIED WARRANTY OF FITNESS IS LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY AND IS LIMITED IN SCOPE OF COVERAGE TO THE SCOPE OF COVERAGE OF THIS LIMITED WARRANTY Jayco makes no warranty of any nature beyond that contained in this limited warranty Jayco does not authorize any person to create any other obligation or liability for it regarding this RV and Jayco is not responsible for representation promise or warranty made by any dealer or other person beyond what is expressly stated in this limited warranty and no one has the authority to enlarge amend or modify this limited warranty Any selling or servicing dealer is not Jayco s agent but an independent entity JAYCO SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTI
198. ur recreation vehicle in the best condition possible Your recreation vehicle must pass the dealer s pre delivery inspection PDI including all systems tests Provide orientation of the recreation vehicle its systems components and operation Request that you read all warranty information and explain any provision not clearly understood Ensure you receive the Warranty Packet Your dealer can assist you in completing the OEM warranty cards or registrations and locate any required component model or serial numbers Complete and return the Warranty Registration and Customer Delivery Form to Jayco within 10 days of delivery to activate the applicable warranty coverage The Limited Warranty is activated only after Jayco receives a signed and dated Warranty Registration and Customer Delivery Form from your dealer SUGGESTIONS FOR OBTAINING SERVICE To help ensure your dealer provides the level of service you expect here are some suggestions we would like to make Contact your dealer at once Do not wait until you are ready to use your RV Your dealer may not be able to service it immediately and or the repair may require parts be ordered The dealer s service department is busiest on Mondays Fridays and before the holidays Prepare for the appointment If you are having warranty work performed be sure to have the right papers with you Take your warranty folder and have your
199. volt DC power supplied by either the converter or auxiliary battery No power is drawn from the battery unless a switch is pushed or turned ON Fuses for the Monitor Panel are located in the Load Center Refer to the manufacturer s operators manual for further information ruu cHGo 23 6000 KAR TANKS fe falza F i ff i Tact a Switches 13 Fair EMPTY weak e e amp e e GRY GRY BLK H20 BAI 2 1 i JD A M ia OA KILO A e JK i ELECTRIC LP GAS EA NDE NEZ Se NS WATER WATER WATER BATT FRESH BLK GREYI GREY ae WATER HEATER H WATER HEATE ll tL PUMP HEATER HEATER Monitor Panel Command Center Panel Monitor panel appearance may vary 85 PLUMBING SYSTEM E_E ta AT gt b Operation Press only one tact switch at a time As you push either the FRESH BLK GREY1 or GREY switch one or more LED lights will illuminate from left to right indicating the content level for that tank When pushing the BATT switch the LED lights illuminate from left lowest to right highest to indicate the estimated auxiliary battery condition NOTE When using shore power all 4 LEDs will light If discon nected from shore power 3 LEDs will light to indicate a full charge The 4th LED may blink The LEDs corresponding to the letters C G F L on the panel indica
200. x your recreation vehicle in direct sunlight Wax it after the surfaces have cooled Do not apply wax to any area having a flat black finish as it can cause discoloration If the finish has been stained with wax wipe off the area with a soft cloth and warm water When waxing the area around the various openings do not apply any wax on the weather strip If it is stained with wax the weather strip cannot maintain a weatherproof seal around the opening Do not use waxes containing high abrasive compounds Such waxes remove rust and stains effectively from the paint work but they are also harmful to the luster of the painted surface since they scrape off the coating Further they are detrimental to glossy surfaces such as the grille garnish moldings etc do not use gasoline or paint thinners to remove road tar or other contamination to the painted surface 130 EXTERIOR MS Polishing your recreation vehicle If painted surfaces have been severely damaged and have lost their original luster and color tone polish the surface lightly with a fine polishing compound Avoid limiting your polishing to the damaged surface only polish a somewhat wider area moving the polishing cloth in one direction After polishing flush the compound from the surface and apply a coat of wax to regain a beautiful luster Do not use a buffer and a buffing compound as it may damage the exterior surface Please contact a professional paint body shop fo
201. y installed water heater bypass which enables you to avoid filling the water heater with RV antifreeze Bypass valves are typically located in close proximity to the water heater Outside utility centers if so equipped operate differently than a factory installed bypass system Refer to the Outside Utility Center section for details n Lu CO E 3 O O 7 Factory installed water heater bypass Normal Camping Usage Valves A amp B Open Valve C is Closed Bypass Mode Valves A amp B Closed Valve C is Open Water Heater Bypass Diagram NOTE In the Water Heater Bypass Diagram valve D is the fresh water tank shutoff Valve E is used to introduce RV antifreeze into the lines when winterizing the system and has a clear hose attached to it See Winterizing the Plumbing System in this manual Valves D amp E are typically located in the vicinity of the water pump which can be under a dinette bench kitchen island or bed Water heater switches if so equipped The water heater switches are located on the Command Center or Monitor Panel Refer to the Monitor Panel or Command Center section of this manual for function details OUTSIDE SHOWER IF So EouIPPED A handheld shower assembly with both hot and cold water may be included for use outside of your recreation vehicle Be sure the water heater is ON and had sufficient time to heat the water Open the outside shower compartment door If dry camping be sure the 12 volt
202. y of any nature beyond that contained in this limited warranty Jayco does not authorize any person to create any other obligation or liability for it regarding this RV and Jayco is not responsible for any representation promise or warranty made by any dealer or other person beyond what is expressly stated in this limited warranty and no one has the authority to enlarge amend or modify this limited warranty Any selling or servicing dealer is not Jayco s agent but an independent entity JAYCO SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES THAT MAY RESULT FROM BREACH OF THIS LIMITED WARRANTY OR ANY IMPLIED WARRANTY THIS EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES SHALL BE INDEPENDENT OF ANY FAILURE OF THE ESSENTIAL PURPOSE OF ANY WARRANTY AND THIS EXCLUSION SHALL SURVIVE ANY DETERMINATION THAT THIS LIMITED WARRANTY OR ANY IMPLIED WARRANTY HAS FAILED OF ITS ESSENTIAL PURPOSE Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you HOW TO GET SERVICE To obtain warranty service the owner must do all of the following 1 Notify an independent authorized dealer of Jayco or Jayco of the substantial defect in material or workmanship attributable to Jayco within the warranty coverage period designated above 2 Provide the notification mentioned in 1 above within te
203. yed on the side of the fire extinguisher NOTE For information on how to use your fire extinguisher refer to the fire extinguisher user s manual provided by the fire extinguisher manufacturer Inspection and maintenance Read and follow all instructions on the label and user s manual provided by the fire extinguisher manufacturer Inspect the extinguisher at least once a week more frequently if it is exposed to weather or possible tampering This should also be done before beginning a vacation or during an extended trip Do not check the pressure test or practice using the fire extinguisher by squeezing the trigger even briefly The fire extinguisher is not rechargeable or refillable Once used it will gradually lose pressure and will not be fully charged for use in an emergency A DANGER Do not turn the electrical power back on or plug in any appliances after the use of a fire extinguisher Please refer to the fire extinguisher s user manual for further instructions on maintenance and clean up SMOKE ALARM Some of the most common fire safety issues are burning candles smoking in bed leaving children unattended and cleaning with flammable fluids The smoke detector is intended to help reduce those risks Your vehicle is equipped with a smoke alarm that is listed for use in Recreation Vehicles 21 OCCUPANT SAFETY E_ O ft aa They are not fool proof Smoke alarms only work if they are
204. you are familiar with their repair policies CUSTOMER RELATIONS Jayco has empowered its dealers to make warranty and repair decisions If a special circumstance occurs that requires information from Jayco we have asked your dealer s service management to make the contact on your behalf This is why you should always talk to your dealer s service management first NOTE Please provide the following information when contacting us for assistance a Customer name and current location mo Phone number where you can be reached n 1 digit chassis Vehicle Identification Number VIN or 9 digit Serial a The current vehicle mileage motor homes Your date of purchase a fapplicable the component description serial number and model number a A detailed description of the concern The name of your selling dealer If different from above the contact information for the RV WARRANTY amp SERVICE ELE S 70 rr ied C Mailing address Shipping address Jayco Inc Jayco Inc Customer Service Customer Service P O Box 460 100 Bontrager Drive 903 S Main Street Bldg 42 Door 4220 Middlebury IN 46540 Middlebury IN 46540 Phone toll free 800 283 8267 Phone local 574 825 0608 Fax toll free 866 709 9139 Brochure request info Jayco com Parts email parts Jayco com Service email service Jayco com Website www Jayco com An important note about alterations and warranties Installations or alterations to the original equi
205. ys of delivery to you to have work performed on any defect or damage to appearance items that occurred at the factory during manufacturer or during delivery at no cost to you as provided by this limited warranty See below under WHAT IS NOT COVERED If two 2 or more service attempts have been made to correct any covered defect that you believe impairs the value use or safety of the RV or if it has taken longer than thirty 30 days for those types of repairs to be completed you must to the extent permitted by law notify Jayco directly in writing at the above address of the unsuccessful repair s of the alleged defect s so that Jayco can become directly involved in making sure that you are provided service pursuant to the terms of this limited warranty WHAT IS NOT COVERED By way of example only this Limited Warranty does not cover any of the following defects in materials components or parts of the RV not attributable to Jayco items that are added or changed after the RV leaves the possession of Jayco additional equipment or accessories installed at any dealership or other place of business or by any other party other than Jayco any RV not used solely for recreational travel and camping all soft goods normal wear tear or usage such as tears punctures soiling mildew fading or discoloration of exterior plastic fiberglass upholstery drapes carpet vinyl screens cushions mattresses and fabrics the effects of condensat
206. ystem can be powered by the 120 volt 60hz utilities found in RV campgrounds or by 120 volt 60hz generator power The following electrical components will only operate when your motorhome is connected to shore or generator power 120 to 12 volt power converter air conditioner refrigerator microwave oven television s home theater system s electric water heater washer dryer fireplace and appliances plugged into convenience receptacles Circuit breakers and fuses will not offer complete protection of the electrical system in the event of power surge or voltage spike Make certain the external power source you connect the power cord to is a properly wired 30 amp NEMA TT 30 RV receptacle and not 240 volt AC 60 ELECTRICAL SYSTEM aasa TESTING THE CAMPSITE POWER CONNECTION The campsite 120 volt power receptacle s should always be tested for proper functionality prior to plugging the recreation vehicle shore power cord into it DO NOT plug the shore power cord into a campsite receptacle s that has reverse polarity non functioning ground circuits or that shows outward signs of heat damage Injury or damage resulting from connection to malfunctioning or improperly wired power sources is not covered by your recreation vehicle warranty Campsite 120 volt power receptacles can be tested using a digital multimeter or a dedicated circuit analyzer Dedicated circuit analyzers plug directly into the campsite power receptacle and minimally
207. zing Itis not affected by high altitudes The output temperature of the water depends on the temperature of the inlet water AND the amount of hot water that is drawn If the inlet water temperature is over 65 F the tankless water heater will generate water in the range of 105 F to 120 F on Low flame depending on the water flow selected by the user Operating Tips Purge air out of ALL hot and cold water lines Open the water heater door and turn the power switch ON Set GMC dial to appropriate setting Open hot water faucet to a medium water flow To reduce temperature Turn GMC dial counter clockwise Increase hot water flow Gradually add cold water To increase temperature Turn GMC dial clockwise Reduce hot water flow For Additional Information For detailed operating information refer to the manufacturer s owner s manual included in the Warranty Packet Winterization Freezing of the water heater and its plumbing components will result in severe damage not covered by warranty For this reason it is advisable to follow the recommendation s below if the unit is to be stored in a freezing environment or for long periods of time At the start of the winter season or before traveling to a location where freezing conditions are likely the unit must be winterized 98 PLUMBING SYSTEM oo The very sm

to your file

Contents

Download Pdf Manuals

Related Search

Related Contents