Layout 2 - TLC Direct
Contents
1. power In this case please be sure to replace the battery If the battery is out of power the next time there is a power cut or power fluctuation the system may not display the correct date and time Step 1 Insert remove SD card mM Unscrew the waterproofed cover using provided Allen key then insert the SD card until it automatically locks into place f you need to remove the SD card please press OFF button and take it out within 30 seconds When LED light turns green meaning SD card is being read do not remove SD card or data may be lost M Toremove SD card push in SD card to eject Once to unlock then pull out Step 2 Installing the GuardCam LED IMPORTANT IF IN ANY DOUBT ABOUT THE INSTALLATION OF THIS PRODUCT CONSULT A QUALIFIED ELECTRICIAN This product must be earthed Do not mount the unit against inflammable surfaces The motion detector will not operate correctly if it is installed Near the outlet of a central heating boiler Near air conditioning plant Pointing directly at moving vehicles Within sight of reflections from moving water Where other lamps could shine on the detector BEFORE ATTEMPTING ANY INSTALLATION OR MAINTENANCE ENSURE THAT THE ELECTRICAL SUPPLY IS SWITCHED OFF AND THE CIRCUIT FUSES REMOVED OR THE CIRCUIT BREAKER IS IN THE OFF POSITION Please make sure the voltage and polarity are correct before connection Incorrect voltage may cause electric shock If y2. 527 515145 Elite Security Products Telephone 01527 515150 Unit 7 Target Park Shawbank Rd Technical Support 01527 515145 Lakeside Redditch B98 8YN email info espuk com www espuk com
3. GUard L am Combined security camera LED floodlight system www espuk com IMPORTANT NOTE PLEASE READ Installation of back up batteries is vital to the correct recording operation of GuardCam LED Under normal operation GuardCam LED requires very little user Intervention The unit will make time and date stamped recordings directly to the installed SD card when the SD card is full GuardCam LED will overwrite the oldest recording therefore maintaining a constant history of recordings To ensure continuation of this operation the time and date settings must not be lost Please make sure back up batteries are fitted correctly upon installation and replaced within 24 hours should the low battery indicator a red flashing light behind the lens of the PIR detector be seen Table of contents Contents OF package uu5n9 excesses coun edaeeesnnstsses 4euseenieenayeess 3 GuardCam LED Motion Light with Video Camera cee eee ees 4 Installation and replacement of back up batteries cece eee 4 Step 1 Insert remove SD Card ccc cc ccc ccc teen eet ne nanes 5 Step 2 Installing the GuardCam LED 0 cece ete tee ees 5 Step 3 Mounting the GuardCam LED ccc cece cee tee ees 6 Step 4 Adjusting the settings ccc cect cette erent eeeennes 7 Step 5 Setting the Date and Time and Video Mode 005 9 Step 6 Viewing Video 2 cece cect cee ete annann 10 Technical Specifications 2s
4. caaiacuaas suinsdsaiwanndd o e eadawns eaaeien 10 General Information and Safety 0 cece cece eee eee eens 11 Contents of package GueardCerni esp GuardCam LED Motion User Manual 3 x AAA batteries Light with Video Camera oY 1 x Allen key 2 X Screws 2 x plastic masonry plugs 2G SD card and SD USB card reader GuardCam LED Motion Light with Video Camera Floodlight Cover High intensity LED Waterproof cover 3 mode selection Camera lens PIR lens Low battery indicator Installation and replacement of back up batteries The function of the back up batteries is to provide power to the PIR Sensor Audio and Date Time settings if a mains power outage occurs and preserve date time settings for a minimum of 48 hours prior to mains power being restored Unscrew the screw A and remove back cover Unscrew screw B and remove battery cover M Put the 3pcs AAA 1 5V batteries into the battery compartment and make sure the polarity is aligned correctly M Replace battery cover and back cover tightening screws carefully Note To guard against damage from battery leakage it is good practice to replace batteries on a yearly basis Jo maintain battery back up function please replace batteries after a total of 48 hours of mains power failure Low Battery Indicator A Red LED light will start to flash from behind the PIR lens when the battery is running out of
5. ease allow 1 minute warm up time after switching on Push the RESET button after switching on Remove plastic lens cover from camera after installation see Fig 5 Step 4 Adjusting the Settings Time control Turn the time control knob to side to increase the illumination time 7 minutes max turn the control knob to side to reduce the illumination time 30 seconds min Sensitivity control Adjust the detector range of Passive W Infrared Motion Fig 6 Sensitivi Sensor 2M 10M Selecting working mode Mode 1 Suggested setting when out of town Light camera speaker all day detection Daytime and nighttime light camera and speaker are all in operation Mode 2 Suggested for day to day use Light at night camera all day speaker in the daytime Daytime light is off camera is on speaker is on Nighttime light is on camera is on speaker is off Mode 3 Perfect for a place of business Light at night camera all day speaker at night Daytime light is off camera is on speaker is off Nighttime light is on camera is on speaker is on Audio mode for different sound selection Option 1 Warning you are being recorded by a security camera Option 2 Dog Barking Option 3 Self recorded message 1 max 10 sec Option 4 Self recorded message 2 max 10 sec Optoin 5 Off LED indicator for indicating the function status of the unit by different colour LED lights 1 Red SD card is not inse
6. n to choose V Video or P Photo If you have not pushed any buttons for 3 second OK will appear on the screen indicating it has automatically saved the current settings The LCD screen will Shut off automatically 10 seconds later On the P photo setting GuardCam LED will take a series of digital photographs at a rate of 3 photos every second when the motion sensor is triggered 2 YEAR Kj 1 START Setting 3 MONTH af 0O 4 DATE Setting h J Setting HOUR C paa MINUTE Setting TTT i Ee Setting VIDEO PHOTO Step 6 Viewing Video Viewing image by computer through USB card reader supplied see Fig 11 M Open SD card housing with allen key supplied Mm Press OFF REC button and remove SD card from the slot M Put the SD card into the USB card reader supplied then insert the card reader into PC via a USB port and open Windows Media Player to view the video Technical Specifications Features and specification PIR detection angle 160 Deg and detection range up to 10M Records 20 seconds image recording for image stream 10fps at 480 640 Pixels Built in SD card slot for SD memory card SD card slot for additional storage max memory size up to 2G SD card spec FAT Automatic exposure control white balance and sharpness Auto Date amp Time stamp Effective viewing angle 60 deg Effective viewing distance 8M Image f
7. ormat JPEG AVI File Powered by AC 100V to 240V subject to requirement 8pcs 1W Nichia super power white LED Auto light sensor Sensitivity control Floodlight time delay control General Information and Safety SPECIAL CARE INSTRUCTIONS The GuardCam LED Motion Light with Video Camera is designed to be weather resistant Never attempt to immerse the unit in water or any other liquid This will damage the unit and void the warranty This product is designed to illuminate video and make verbal announcements It will not prevent the commission of any act legal or illegal The manufacturer assumes no liability for any damage to property injury to person or death Use a soft lens cloth for cleaning lens Avoid touching lens with fingers Remove dirt or stains with a soft cloth dampened with water or neutral detergent Keep the GuardCam LED Motion Light with Video Camera in a dry and cool dust free environment or container when it is NOT used Do not open the GuardCam LED Motion Light with Video Camera for unauthorized service This could cause serious damage to the unit and will void the warranty This GuardCam LED Motion Light with Video Camera is a precision electronic device Do not attempt to service this camera yourself as opening or removing covers may expose you to the danger of electric shock or other risks To avoid risk of burns due to high temperature do not touch the floodlight when it is turned on Technical Support 01
8. ou are not sure please contact your retailer Note It is recommend to mount GuardCam LED 2M above the ground for optimum performance do not mount the fixture below 1 2M See Fig 3 for details of performance range Detection range 10M x 160 see Fig 2 Step 3 Mounting your GuardCam LED 1 1 Place plastic masonry plugs into desired surface aligning holes as Shown below Using an electric screwdriver fasten mounting plate directly to surface using screws E 2 Feed the cable through the back mounting box and bush the cable entry to avoid abrasion to the cable 3 Wire the unit as follows Ensure all wires are connected securely and Toth g AC power cor that no loose strands are exposed ic 3 SY ScrewA INCOMING SUPPLY TO FITTING EARTH Green amp Yellow ces iP ma EARTH Green amp Yellow NEUTRAL Blue or Black NEUTRAL Blue or Black i L Q LIVE Brown or Red LIVE Brown or Red 4 Make sure the polarity is correct Double check the connections after wiring Errors may damage the motion sensor or cause a fire hazard 5 Attach the unit to the mounting plate You will first need to angle the unit back so that the catch at the top of the mounting plate fits into slot on the back of the unit Next lower the unit until holes at ee eee the bottom of the mounting plate lt 7 ScrewA and unit are flush Then screw r screw A into this hole tightening carefully r RS Pl
9. p twice to erase the message 2 If record 2 messages push the button one time to listen to the first message push again to listen to the second message To erase the message you just listened press the button for 3 seconds after twice beep the message is erased 3 Erase all messages press the button for 3 seconds after twice beep messages are erased Please note that if you just listen to all messages 10 seconds pause is necessary otherwise what you erase is the one you just play 4 If message 1 is erased message 2 will automatically become message 1 For one more message record it will then be set to message 2 MICROPHONE Step 5 Set the Date and Time and Video Mode This will allow the security video taken by GuardCam LED to display the correct date and time it was taken 1 Push TIME DATE SET button see fig 10 for 3 seconds The LCD screen will then flash 3 times indicating you have entered Time Date setting mode 2 YEAR setting Y and 08 are displayed on the screen push the button to set year from 08 99 push the button again and hold for 3 seconds to scroll through numbers quickly If you have not pressed the button for 3 seconds it will automatically save the year and go on to allow you to set the month 3 Repeat the same setting procedure for MONTH DATE HOUR MINUTE 4 VIDEO PHOTO setting when entering this mode these two icons and V appear on the screen push the butto
10. rted into the SD slot or the system is malfunctioning 2 Green The unit is recording or USB is inserted and connecting with the computer 3 LED off stand by SD card is inserted into the slot when off record button is pressed Please note when off record button is pressed remove SD card within 30 seconds now the LED will turn red after SD card is removed from the slot 3 Position Switch RESET Hf o anime ai i OFF REC Mo Ow D le 90 Fig 7 M Reset button restore functions to default settings 1 Press RESET button once each time you turn on unit 2 Please press this button in case of system malfunction M Off Rec Please press Off Rec button to remove SD card Please remove card within 30 seconds of pressing the Off Rec button to avoid loss of data M Set Rec record your own message see fig 9 1 Press this button for 3 seconds start recording your message after beep Push the button again to stop recording and you will hear beep twice or it will stop itself after 10 seconds 2 If you have recorded one message repeat above step for message 2 it will be arranged right after the first recorded message The message will automatically update to the latest one if you don t erase the old message M Play Erase listen and erase the message see fig 9 1 If record 1 message only push the button one time to listen to the message just recorded press for 3 seconds hearing bee
Download Pdf Manuals
Related Search