Owner`s Manual Invader 2420
Contents
1. TF in the fixtures bank for the convenience to check other channels there would be some output of the channels but the channel output will not be stored in the centre Press MANUAL REC button at this moment all LEDs on CUE OVERRIDE CENTRE FIXTURE GROUP PRESET CHASE BANK BLACKOUT blink at the same time Press CENTRE button Press the number button 1 20 to select the location to store the Centre all LEDs blink for 3 times to indicate that you have successfully edited a Centre position Press PROGRAM button for 3 seconds to exit Program mode the LED goes out indicating this operation NOTE If you press different buttons in step 3 and 9 the centre position you set in step 3 will cover the one in step 9 2 19 Programming an override 1 20 3 1 Enter Program mode 2 Press FIXTURE button Press the number button 1 20 to select the concerned fixtures to be programmed Use FADERS 1 24 and 4 Jog wheels to adjust the selected fixture to your desired effect 5 Press MANUAL REC Button at this moment all LEDs on CUE OVERRIDE CENTRE FIXTURE GROUP PRESET CHASE BANK BLACKOUT blink at the same time Press OVERRIDE button 1 20 7 Press the number button 1 20 to select the to be stored Override number all LEDs blink for 3 times to indicate that you have successfully preset an Override effect 8 Repeat steps 2 7 to program other Override effects 9 Press PROGRAM button for 3 seco2. BEAM ANGLE N CTC CTC N REFT EFFECT ROT N EFFECT N FRAM FRAME1 N E AG RAME1ANGLE PT IM PT_MACRO ZOOM ZOOM N SPED SPEED N CONT CONTROL N MACO MACRO N EA FUNCTION A N ER FUNCTION B N F C FUNCTION C N Er FUNCTION D NEES FUNCTION E N EE FUNCTION F KN FUNCTION G gt N EG FUNCTION H NET FUNCTION N EJ FUNCTION J FUNCTION K N EE FUNCTION L Note 1 All the character must be capitalization except commentary which after 2 The finished file should use a short name below 8 characters all use capital letters and suffix with CIF transitorily or the controller can t read up the profile information 3 Don t change the group which contain 4 Display information should be no more than 4 character and without blank Technical specification Power Input 100 240 VAC 50 60 Hz FUSCsccsidvancdasiedewadedwmsanaxvnes T A 250 V 5x20 mm DMX Output 3 pin XLR socket Stand Alone n se 5 pin XLR plug MIDI Signal socias 5 pin DIN standard interface Audio Input By built in microphone or line in Dimensions 065 483 x 263 x 100 mm WII EE 5 8 kg Our products are subject to a process of continual further development Therefore modifications to the techni cal features r
3. E 6 Repeat 3 5 to patch all the fixtures ENTER MAIN MENU 7 Back to the last menu please press ESC CLEAR button 1 5 Reverse channel setup 1 Enter Menu Mode 2 Turn Jog wheel 1 up to when the 05 Reverse channel setup is shown on the monitor press ENTER MAIN MENU Button to enter ENTER MAIN MENU EI 3 Press number Button 1 20 to chose the fixture which needs to reverse Turn Jog wheel 2 to change the position of the cursor and Jog wheel 4 used to reverse the channel 2 4 PAN FINE TILT FINE 3 4 Turn Jog wheel 3 to chose the channel Jog wheel 4 to reverse o TILT FINE 6 Press ENTER MAIN MENU Button to enter all the LEDs will blink for 3 times 7 Repeat 3 6 to reverse other channels 8 Back to the last menu please press ESC CLEAR button ESC CLEAR 1 Enter Menu Mode 2 Turn Jog wheel 1 up to when the 06 Fade mode setup is shown on the monitor press ENTER MAIN MENU button to enter 3 Turn Jog wheel 2 to select only pan tilt or all channel 4 Press ENTER MAIN MENU Button to enter all the LEDs will blink for 3 times then back to the last menu 1 7 Blackout mode select Enter Menu Mode Turn Jog wheel 1 up to when the 07 Blackout mode select is shown on the monitor press ENTER MAIN MENU button to enter Turn Jog wheel 2 to chose Stand by or Pan tilt centre or Blackout scene Press ENTER MAIN MENU Button to enter all the LEDs
4. 6 PROGRAM Enter Program mode Press the number button1 20 to select one or more fixtures Move FADERS1 24 to vary the channel outputs or use Jog wheel 1 2 to adjust PAN and PAN FINE or use Jog wheel 3 4 to adjust TILT TILT FINE Once the effect is adjusted press MANUAL REC button to store at this moment all LEDs on CUE OVERRIDE CENTRE FIXTURE GROUP PRESET CHASE BANK BLACKOUT blink at the same time Press BLACK OUT STAND ALONE button all LEDs blink for 3 times to indicate that you have successfully stored a Black Scene Press PROGRAM button for 3 seconds to exit Program mode the LED goes out indicating this operation 3 Function mode Press MANUAL REC MUSIC BANK COPY AUTO DEL Button to enter into manual mode or sound mode or auto mode 3 LRunning scene Scene can be open solely in the manual mode but in the sound or auto mode it should circulate with some BANK 1 Manual Mode Press BANK Button N Press MANUAL REC to into manual mode The LED of MANUAL REC will be on MANUAL A m Use Jog wheel 1 to select the bank you anticipate Press number Button to open the scene 2 Sound Mode 1 Press BANK Button Press MUSIC BANK COPY Button to into sound mode the LED of MUSIC BANK COPY will be on music A BANKCOPY Use Jog wheel 1 to select the bank you need then the scene in the bank will run with music When it is running the scene with Moveme
5. STROB enter setting menu Use jog wheel 2 to set the strobe speed of the simulate strobe light a PROGRAM Use jog wheel 3 or 4 to set the value of DIMMER 0 255 or SPEED 0 255 that out of the strobe light Press ENTER MAIN MENU button to store press PROGRAM button to exit ENTER MAIN MENU PROGRAM SR 3 Control Press STROBE button then the controller will control the DMX strobe light with the value of the DMX be set and the light strobe in the speed that be set to the simulate strobe light 6 MIDLfunction list MIDI Channel 1 15 note number function S y 5 MIDI Channel 0 LT mor channel Note number Command men NEC TEE ors ante TES DON Tee IES Ier Bank 5 Bank 8 MIDI 2 00 79 Turn on or turn off scenes from Bank 5 8 Pit 100 119 Turn on or off CUE 21 40 ma 120 127 Bank 9 Bank 12 MIDI 3 00 79 Turn on or turn off scenes from Bank 9 12 LML Channel Note number Command _ SSES ors oe Tm or arf 06 80 nor Le Re tanos SS Bank 21 Bank24 woe 00 79 Turn on or turn off scenes from Bank 21 24 Bank 29 Bank w s 00770 Tom on ortum of scene fom Bank 10732 Bamas Bankse moio 00 70 Tumon ortum of scenes fom Bank 395 7 Update the software with CF card Format the program of the controller then download the last software and copy to CF SUP2420 APP2420 SUP inset the CF card to the seat press FIXTURE and L OVERRIDE and number
6. Button to enter LCD will show 01 Save program file Press ENTER MAINMENU Button to enter Use Jog wheel 2 to select Yes no Press ENTER MAINMENU Button to enter Yes to save No to exit name and move the cursor you can input as munch as 8 characters e 5 Select Yes then LCD will hint to input file name Use Jog wheel 4 to select the file ENTER MAIN MENU A 6 Press ENTER MAIN MENU Button to store it will be finish after about 2 minutes 7 Press ESC CLEAR Button to back to the last menu 2 times to back to the main menu 1 13 Modify password 1 2 Enter Menu Mode Turn Jog wheel 1 up to when the 13 Modify Passwords shown on the monitor Press ENTER MAIN MENU button to enter Use Jog wheel 1 to select power on password or memory protect password Press ENTER MAIN MENU Button to enter Use number Button 1 10 to input 6 digit old password 10 equal to number 0 if the password is wrong it will hint to input continually It will hint to input new 6 digit password after get exact password You have to input the same password twice it will back to the last menu automatically after change the password successfully Use Jog wheel 2 to select Power on password or memory protect password Press ESC CLEAR Button to back to the last menu and again to the main menu 1 14 Enable password Enter Menu Mode Turn Jog wheel 1 up to when the 14 Enable password shown on t
7. Lock Unlock memory Need password to clear all memory Standard MIDI facility gt Lighting Library and software downloaded available gt DMX 00 machine control 481 Ch gt Both DMX 483 amp 484 and analog strobe control available Via LCD display people can adjust the speed of analog strobe 2 remote Easy Controller CA 8 Gooseneck USB LAMP NOTE Some basic knowledge of MIDI and DMX is required to fully utilize this unit General instructions Please read the user manual carefully as it includes important information regarding details of operation maintenance and technical data Keep this manual with the unit for future consult WARNINGS DO NOT make any inflammable liquids water or metal objects enter the unit Should any liquid be spilled on the unit DISCONNECT the power supply to the unit immediately STOP using the unit immediately In the event of serious operation problems and either contact your local dealer for a check or contact us directly DO NOT open the unit there are no user serviceable parts inside NEVER try to repair the unit yourself Repairs by unqualified people could cause damage or faulty operati on Contact your nearest dealer CAUTIONS This unit is NOT intended for home use After having removed the packaging check that the unit is NOT damaged in any way If in doubt DON T use it and contact an authorized dealer Packaging material plastic bags polystyrene foam nails et
8. Press the number button1 20 to select one or more fixtures to make the fixture group 4 Press MANUAL REC button at this moment all LEDs on CUE OVERRIDE CENTRE FIXTURE GROUP PRESET CHASE BANK BLACKOUT blink at the same time MANUAL Press FIXTURE GROUP button Press the number button 1 20 to select the number of the fixture group for store all LEDs blink for 3 times Repeat steps 2 6 to edit more fixture groups 8 Press PROGRAM button 3 seconds to exit Program mode the LED goes out indicating this operation PROGRAM 2 16 Fixture group editing Enter Program mode Press FIXTURE GROUP button FIXTURE N GROUP Press the number button 1 20 to select the fixture group number to be edited Press FIXTURE button FIXTURE EI 5 Press the number button 1 20 to select one or more fixtures to make the fixture group 6 Press MANUAL REC button at this moment all LEDs on CUE OVERRIDE CENTRE FIXTURE GROUP PRESET CHASE BANK BLACKOUT blink at the same time MANUAL al Press FIXTURE GROUP button FIXTURE N GROUP 1 20 8 Press the number button 1 20 to select the fixture group number you selected in step 2 all LEDs blink for 3 times 9 Press PROGRAM button for 3 seconds to exit Program mode the LED goes out indicating this operation PROGRAM NOTE If you press different buttons in step 3 and 7 the fixture group you selected in step 4 will cover the one in step 7
9. THREATENING situation exists niemals e Z Risk of fire Never leave the device unattended during operation Never cover the ventilation slots of the device while it is on Do not place the device in locations that are subject to direct sunlight If you do it may overheat and become irreparably damaged Never operate the amplifier in the vicinity of heat sources such as cookers heating elements or other heat producing installations Do not place open fire sources such as candles on the device Before a storm and or a thunderstorm with a risk of lightning please disconnect the device from the electri cal power source Risk of personal injury Keep children away from the power cord and the device Children frequently underestimate the dangers of electrical devices Provide a stable location for the device Do not operate the device if it has sustained a fall or is damaged Have the device checked or if necessary repaired by qualified technicians Maintenance and care Never submerse the device in water or any other liquid Don t let any liquid get into the housing This would damage the unit and cause a short circuit Before cleaning the device you must disconnect it from the mains Clean the surface of the device only with a slightly damp cloth Never use petrol solvents or any aggressive cleaners These could damage the sur face of the unit s housing Introduction Thank you for purchasing our Invader 2420 Enjo
10. button 1 20 to select the chase number Press the button TAP INSERT to insert a step following the present position Use the Jog wheel 1 to select the Bank number of the inserted scene El 7 Press the number button 1 20 to select the scene to be inserted 8 Use the Jog wheel 3 4 to adjust the CHASE FADE TIME and WAIT TIME If you do not make any adjustments the system will remember the last FADE TIME or WAIT TIME 9 Press the button MANUAL REC all LEDs blink for 3 times to indicate that you have successfully inserted a step into a chase 10 Repeat steps 5 9 you can insert 200 scenes to each chase MANUAL 2 m 11 Press the button CHASE to store the chase and exit the chase programming state 12 Press the button PROGRAM for 3 seconds to exit Program mode the LED goes out indicating this operation PROGRAM 2 11 Deleting steps from program 1 Enter Program mode 2 Press the button CHASE use jog wheel 1 to select the page number choose the programming chase Press the number button 1 20 to select the chase number to delete from Use Jog wheel 2 to select the scene location you want to delete Press AUTO DEL all LEDs blink for 3 times to indicate that you have successfully deleted the scene Repeat steps 4 5to delete more scenes from the chase Press the button CHASE to store the operation and exit from the present programming state 8 Press the button PROGRAM for 3 seconds
11. button 15 then Power on afresh until the information show on FIXTURE OVERRIDE the LCD display the controller will test if the CF card stick well and then update the new Ca software it will cost about 20 seconds please don t move the CF card or cut the power in order to avoid update frustrated and damage the CF card 15 Save the program first or updating the software may lead the memory program useless Please refer to Write CF card and Read CF card to operate NOTICE The format of the CF card should be FAT12 or FAT16 but not FAT32 and NTFS be sure there is no long name files under the root directory the amount of the name below 8 the character must be start with let ters and compose with letters or number or underline 8 Profile create notice PROFILE CIF as the profile cyclostyle The finished file should use a short name below 8 characters All use capital letters and suffix with CIF transito rily IL 2420 controller nonsupport long file name or the controller can t read up the profile information IM 1200S CIF is the profile of ACME IM 1200S Enactment special code so the controller should distil some channel characteristic to manage ARRT CODE D DIMMER DIMMER P PAN PAN PF PAN FINE PAN FINE in 16 channel mode T TILT TILT gt TF TILT FINE TILT FINE in 1 6 channel mode G ALL GOBO CORRELATION CHANNELS transfer all gobo correlation channel to preset gobo C ALL COLOUR COR
12. button to enter The list of the program profile files will show on the LCD turn jog wheel 1 to select the file name The amount of the files consider to the amount of the program or profile files which you saved under the directory of DIR2420 in the CF card Use Jog wheel 2 to select Yes no Press ENTER MAIN MENU Button to enter After read up the file the LCD will hint to complete Repeat 3 7 to read up other files Back to the last menu please press ESC CLEAR Button Press ESC CLEAR Button 2 times to back to the main menu or 3 times to exit the menu NOTE Please backup the programs before you load program file or the program file you load will replace all the program in the controller The controller should store finite bank files except the current bank files you can store 50 include create by the controller immediacy more at best So please store the files in the CF card or computer and read up the files which you have to use only 1 12 Write CF card You can store the finished program to the directory of DIR2420 which under the root directory of CF card Every time read the CF card please don t move it or the card or the files will be damaged The format of the CF card should be FAT else you have to convert it to FAT by PC and copy it to CF card 1 MAIN MENU Enter Menu Mode Turn Jog wheel 1 up to when the 12 Write cf card is shown on the monitor Press ENTER MAIN MENU
13. running the scene with Movements in sound activation mode it will process repeatedly as per the built in movement Loop time then enter next step Press CHASE Button use jog wheel 1 to select chase page Press AUTO DEL Button to enter auto mode the LED of AUTO DEL will be on 1 20 3 Press number Button 1 20 to select the program you anticipate You can choose much more than one CHASE and they will run on the train that you select them 4 Setting to CHASE RUN BY INSIDE TIME then it will run as the FADE TIME or FADE TIME of the step that you set when store the chase Setting to CHASE RUN BY OUTSIDE TIME then it will run as the FADE TIME or FADE TIME you set last time you can also adjust by turn the joy wheel 3 or 4 or use TAP INSERT Button to adjust the speed gt P RT 7 m NOTE When you press TAP INSERT to adjust the speed adjusting the running speed of the scene is based on the interval of pressing the Press TAP INSERT Button twice which no more than 10 minutes 3 3 Running a cue CUE can only run in manual mode 1 Press CUE Button use jog wheel 1 to select chase page g 3 1 20 2 Press number button 1 20 to select the CUE you anticipate You can choose much more than one CUE and they will run on the train that you select them NOTE If a CUE includes several chases with different run time we regard the run time of the chase with the longest run time as the CUE s longest run time and the chase wi
14. selected 3 1 10 can be used to select 10 groups of COLOUR PRESET 11 20 can be used to select another 10 groups of GOBO PRESET 4 1 20 can be used to select 20 CUE PAGE CHASE PAGE SCENE BANK OVERRIDE CENTRE FIX TURE Fixture number channel list Fixtures number buttons Fixture DMX channels 241 264 23 ESC CLEAR Button Back to last menu delete all the output when program 24 Enter main menu Button Confirm or enter next menu or enter main menu 25 LCD Display Show the current activity or programming state 26 Jog wheel Used to adjust the chase speed within the range of 0 1 second to 5 minutes Rear view soot d A Y 1 Power in AC100 240V 50 60Hz 2 Power Switch This switch turns On Off the power 3 STROBE Trigger non DMX strobe Signal 12V DC 4 AUDIO 0 1V 1Vp p 5 MIDI IN or MIDI THRU Receives MIDI data 6 DMX Out Two connectors sends DMX signals to DMX fixtures use 3 pin XLR plug cable to link the fixture together 7 STAND ALONE The connectors are used only in master slave mode using 5 pin XLR cable microphone jack of the first fixture you will find that the remote control on the first unit will control all the other units for Stand by Function and Mode Operation guide Operating steps instructions When power is turned on the controller starts self testing automatically the LCD Display indicating the self testing progress After it is finished the fixture pilot on the rear boar
15. to exit Program mode the LED goes out indicating this operation PROGRAM 2 12 Deleting a chase 1 Enter Program mode 2 Press the button CHASE use jog wheel 1 to select the page number choose the programming chase 3 Press the button AUTO DEL L 1 20 4 Press the number button 1 20 to select the chase to be deleted all LEDs blink for 3 imes to indicate that you have successfully delete the chase 5 Repeat the steps 2 4 to delete more chases 6 Press the button PROGRAM for 3 seconds to exit Program mode the LED goes out indicating this operation PROGRAM 2 13 Programming a preset 1 Enter Program mode 2 Press the button FIXTURE FIXTURE EI 3 Press the button 1 20 to select the concerned fixture of preset programming Move the FADERS1 24 to change COLOUR GOBO channel values The codes of the channel feature of ARRT CODE are C and G in the fixtures bank output for the convenience to check other channels but the channel output will not be stored in the preset 5 Press the button MANUAL REC at this moment all LEDs on buttons CUE OVERRIDE CENTRE FIXTURE GROUP PRESET CHASE BANK BLACKOUT blink at the same time Press the button PRESET PRESET Use Jog wheel 1 to select the preset group number 1 20 1 20 8 Press one of the number button 1 10 to store a COLOUR preset or press one of the number button 11 20 to store a GOBO preset all LEDs blink for 3 times to indicate that y
16. will blink for 3 times then back to the last menu Enter Menu Mode Use Jog wheel 1 up to when the 08 Midi channel select is shown on the monitor Press ENTER MAINMENU Button to enter Use Jog wheel 2 to chose the channel of MIDI 0 16 it s enlarge mode when the value of the MIDI channel is 0 so MIDI can receive the information of 1 16 O d channels A _ PAN FINE Press ENTER MAIN MENU Button to enter all the LEDs will blink for 3 times then back to the last menu 1 9 Chase run by inside outside time 1 2 3 H ENTER MAIN MENU V Enter Menu Mode Turn jog wheel 1 up to when the 09 Chase run by inside outside time is shown on the monitor Press ENTER MAINMENU Button to enter Use Jog wheel 2 to chose Chase run by inside time or Chase run by outside time Press ENTER MAIN MENU Button to enter all the LEDs will blink for 3 times then back to the last menu 1 10 Auto remote address This function is used only for the fixtures which can be addressed long distance ensure the unit match this requirements before operation or it will be of no effect 1 Za ENTER MAIN MENU ENTER MAIN MENU V Enter Menu Mode Turn Jog wheel 1 up to when the 10 Auto remote address is shown on the monitor Press ENTER MAIN MENU Button to enter Use Jog wheel 2 to select Yes enter or NO quit to the main menu Press ENTER MAIN MENU Button to set the address of the
17. 2 17 Programming a centre 1 Enter Program mode 2 Press FIXTURE button Move FADERS1 24 and use Jog wheel 3 4 to change the centre position of PAN TILT where you desired The codes of the channel feature of ARRT CODE are P PF T TF in the fixtures bank for the convenience to check other channels there would be some output of the channels but the channel output will not be stored in the centre 5 Press MANUAL REC button at this moment all LEDs on CUE OVERRIDE CENTRE FIXTURE GROUP PRESET CHASE BANK BLACKOUT blink at the same time MANUAL Press CENTRE button Press the number button 1 20 to select the location to store the Centre all LEDs blink for 3 times to indicate that you have successfully stored a Centre position 8 Repeat steps 2 7to program more Centre positions 9 Press PROGRAM button for 3 seconds to exit Program mode the LED goes out indicating this operation PROGRAM 2 18 Centre editing 1 Enter Program mode 2 Press CENTRE button EI 3 Press the number button1 20 to select the edited Centre position number 4 Press FIXTURE button FIXTURE N 5 Press the number button 1 20 to select the concerned fixtures to be programmed FIXTURE D 10 PROGRAM Move FADERS 1 24 and use Jog wheel 3 4 to change the centre position of PAN TILT where you desired The codes of the channel feature of ARRT CODE are P PF T
18. E of present chase the Jog wheel 4 to adjust the WAIT TIME of the present chase If you do not make any adjustments the system will remember the last FADE TIME or WAIT TIME Press the button MANUAL REC all the LEDs will blink for three times briefly indicating the store succeed Repeat Step 4 6 each chase can have 200 scenes max Press the button PROGRAM for three seconds to exit Program mode the LED goes out indicating this selection 2 8 Program all the scenes in a bank 1 Press the button CHASE use jog wheel 1 to select the page number choose the Enter Program mode programming chase Press the number button 1 20 to select the Chase number LEDs on the BANK button will be all lit the LCD will show the number and parameter of the CHASE BANK SCENE STEP FADE WAIT Use the Jog wheel 1 to select the Bank number of the programmed Chase 5 Use the Jog wheel 3 4 to adjust the FADE TIME and WAIT TIME which are going to be added to the single Chase If you do not make any adjustments the system will remember the last FADE TIME or WAIT TIME 6 Press the button MUSIC BANKCOPY music A BANKCOPY 2 7 Press the button MANUAL REC all LEDs blink for 3 times all the programmed scenes in the Bank will join the Chase 8 Repeat Step 3 7 can join 200 scenes max to the chase MANUAL REC 9 Finally press the button CHASE to store the chase then exit the programming state 10 Press the but
19. ING SEEDS MOM ele elle ET 31 ANA NN 32 ZAS PrOGFAMUIMIAG A PES WEE 32 NN 33 215 PLOGlAMIMING WE ire GROUP DEET 35 elei lee le TEE 36 Ee et 8000 Ben A 37 SEET 38 E ee et agangen Be de 39 ZZ Klee elle EE 40 ee ET ae 5 44 44434 444 EE 42 222 Eeler 42 O 43 32A SOE e ee EE 44 O A AE O EEEE AE 44 a A 45 A EE 46 SRA a RE 48 IA OVER CO MO EE 48 FOG IMAGINE Operaatio EE 49 5 SODE gt OPIO EE 49 Ox MIDI TUMCTOM EE 50 7 Update The software WALA SP Cda dt dnd 51 By PROMME CREATE NO triada 52 Technical elle EE 55 EE e 7 55 Notes on safety For your own safety you should read through this chapter at first completely A AN Risk of electrical shocks Only connect the device to a properly wired and earthed mains power socket with mains voltage of 230 V 50 Hz Do not operate the device if the power cord or the mains plug are damaged Never submerse the device in water Wipe it with a slightly moistened cloth only Do not expose the device to rain and never use it in a damp or wet environment Make sure that the power cord never becomes wet or moist during use Under no circumstances may you open the device housing Should you do so your safety would not be assured and the warranty will become void There are no operational
20. Invader 2420 Owner s Manual DMX Controller Please carefully read this manual 55 FAIR Content Notes ON SIE EE 3 MAINTE rell BEE 3 FO DUCTION EE 4 CHIESA deet en EE 4 Generals TUCIONS ae 5 GSS dat 5 RL 5 VEL VIEW tere Dee Ae 5 Operation guide Operating Steps INSTRUCHONS anciana seas 8 A A A E EN RET E AN A E E A TAE 8 Tel CREATE a NewTIXture DOME sa a id oir TEE 9 k2 Modi a MXtUrE PON Es sieru ean eege een Eege EES 10 b3 Delete Ire UE 11 ak Patea XUE ioin ta oa E EEA 12 1S REVEISE CANNEL SED EE 12 MeO FACES Mode SECU EE 13 17 Blackout mode Selecta tddi 14 1 8 Midrcnannel Selena 14 1 9 Chase TUN Nee ee TEE 15 WIO AUTO remote ele 15 A 16 AZTECA ENEE dE ind an 17 MES 18 MS A 19 1 15 Erase A dps ucsnenteaateanattvaantt 19 16 AUdIO inp t range AUS WEE 20 1 17 Ghannel value display MOTE aciacomincrniocion sitiada semaine and sede ad acta nerd an dada taa 20 2 Programming Mode A 21 A 21 2 2 AS eege SEENEN ENEE A EE N EN 22 STEESEL 0 20000 23 2 4 ele 24 Zid DEIECE a SCENE senger Lengt leg eeler eet 25 220 BANK NN 25 ZF are ell ET 20 7 reelle iN Dell 27 227 PIOGKAIM ASTD NA 28 2 VOINSErE STEPS IMO Sl Maras rinitis 7 29 2 11 DElET
21. OLOUR 8 G GOB15 GOBO1 9 G RG GOBO 1 ROT 10 G ont GOBO 1 ROT LOW 11 G 6082 GOBO2 12 6 R 62 GOBO 2 ROT 19 G RG2L GOBO 2 ROT LOW 14 N EFFI EFFECT 15 N R_EF ROT EFFECT 16 N JS IRIS 17 N FCUS FOCUS 18 N ZOOMT ZOOM 19 P PANS PAN 20 PF EF PAN FINE 21 T TILTS TILT 22 TF CP TILT FINE 23 PT PTS SPEED P T 24 N SPED PEED DMXEND END ARRT CODE D DIMMER P PAN PF DAN FINE To TILT TF TILT FINE PT OTHER PAN TILE CORRELATION CHANNLES G ALLGOBO CORRELATION CHANNLES C ALL COLOUR CORRELATION CHANNLES N ETCAETERAS CHANNELS ARRT CODE MAX 2 CHARACTER DISPLAY INFORMATION MAX 4 CHARACTER DON T HAVE BLANK CHANNEL FUNCTION 0 zZ 0 S gt DIM DIMMER SHUT SHUTTER PAN PAN PF RF PAN FINE T Si TILT JS TILT FINE PT Plo P T SPEED G GB15 GOBO 1 6 RGB1 GOBO 1 ROT G GB2 GOBO 2 G RGB2 GOBO 2 ROT G GB35 GOBO 3 6 ROB3 GOBO 3 ROT C COL1 COLOUR 1 C COL2 COLOUR 2 C CYAN CYAN C YELLOW C MAGT MAGENTA C CYMM CMY MACRO N FROS FROST N PRSM PRISM N RPRS PRISM ROT N FCUS FOCUS N_ IRIS IRIS N BANG
22. RELATION CHANNELS transfer all colour correlation channel to preset gobo N ETCAETERAS CHANNELS else channels should be signed N The channel display message should be no more than 4 capital letters or underline or number and must be bracket with double quotation marks Don t replace by blank if shorter 4 charac ter You d better input in English mode ensure all the input characters are DBC but not SBC case O DIM right 2 DIM wrong for the blank dim Dim wrong for the lowercase DIM wrong for the SBC double quotation marks Don t change the group which contain Store the profile that you want to input to the controller under the root directory of CF card EXP If CF card is disk F then the file input route should be F DIR2402 IM 1200S The format of CF card should be FAT16 but not FAT32 IL 2420 PROFILE VER1 0 sin ADD ACME AND OTHER LIGHT LIBBER SELECT DEFAULT ACME ACME AND OTHER FACTORY MODEL MODEL MAX 16 CHARACTER NAME AMCE _ IM 1200SZ 24 LIGHT CHANNEL NUMBER MAX 24 CHANNEL 24 DMX see DMX CHANNELS LIST CHANNEL MAX 24 DON T REPEAT MAX 2 CHARACTER ARRT CODE MAX 2 CHARACTER DISPLAY INFORMATION MAX 4 CHARACTER DON T HAVE BLANK CHANNEL FUNCTION 1 N SHUT SHUTTER 2 D DIMf DIMMER 3 C 00 CYAN 4 C C_M MAGENTA 5 C GE ger YELLOW 6 C CTC CTC i C AER C
23. alue display mode 1 Enter Menu Mode Turn Jog wheel 1 up to when 17 Channel value display mode shown on the moni or press ENTER MAIN MENU Button to enter 3 Use Jog wheel 2 to select 0 255 0 0 100 DA Press ENTER MAIN MENU Button to store and back to the main menu back to the main menu without any change Press ESC CLEAR Button 2 Programming mode Press PROGRAM button for 3 seconds the LED above this button lights blinking indicating Program in active PROGRAM 2 1 Setting a scene 1 20 1 2 3 Enter Program mode Press the button 1 20 to select Fixture you can select several fixtures at a time by tapping of these buttons Slide Faders 1 24 or use the CENTRE or PRESET or SCENE have saved to change the output of each channel You can also use the jog wheel 1 amp 2 to control the PAN PAN FINE or use the jog wheel 3 4 to control TILT TILT FINE Once the scene is satisfactory press MANUAL REC button to program this scene into memory At this moment the LEDs on CUE OVERRIDE CENTRE FIXTURE GROUP PRESET CHASE BANK BLACKOUT button blink at the same time Press BANK use the Jog wheel 1 to select the BANK number to save the scene Press the number button 1 20 to select the Scene number going to be saved all LEDs and the Segment Display will blink three times briefly indicating this operation then the LCD will show the bank and the scene number of the programmed scene 7 Repeat st
24. c MUST NOT be left within children s reach as it can be dangerous This unit must only be operated by adults DO NOT allow children to tamper or play with it NEVER use the unit under the following conditions In places subject to excessive humidity In places subject to vibrations or bumps In places with a temperature of over 45 C 113 F or less than 2 C 35 6 F Protect the unit from excessive dryness or humidity ideal conditions are between 35 and 80 DO NOT dismantle or modify the unit Overview Front view 1246 8 911 131517 18 19 o OY SEE E E OY ca ON LANA a d ul 20 EN 3 5 7 1022 12 14 16 2324 26 25 10 11 12 13 14 15 16 17 18 19 20 21 22 6 gt ON gt Fog Machine Button STROBE Button Fixture Group Button Fixture Button Preset Button Movement Button Chase Button Cue Button Bank Button Override Button Centre Button Manual Rec Button Program Button Music Bank Copy Button Tap Insert Button Auto Del Button Blackout Stand Alone Button USB Light Faders CF card Stand alone Activates Fog Machine Trigger strobe Select set one or more fixtures group Select one or more fixtures Select set the colour amp gobo preset Select set the pan amp tilt movement Run Chase and save Scene to Chase Save several Chases together and make them run at the same time Press the Bank butt
25. cating this selection PROGRAM 2 6 Bank copying 1 Enter Program mode 2 Press BANK button Use the Jog wheel 1 to select the Bank number of the being copied scene Press the button MANUAL REC LEDs on CUE OVERRIDE CENTRE FIXTURE GROUP PRESET CHASE BANK BLACKOUT blink at the same time Then turn the Jog wheel 1 to select the bank number to copy to Press the button MUSIC BANK COPY all LEDs and the Segment Display will blink for three times briefly indicating this operation then the LCD will show the number of the being copied bank and the bank is being copied to and the scene number of the programmed scene music A BANKCOPY 7 Press the button PROGRAM for three seconds to exit Program mode the LED goes out indicating this selection PROGRAM 2 7 Program a chase Note The chase should be programmed after the scene is set Each chase can have 200 scenes max 1 Enter Program mode 2 Press the button CHASE LEDs on CHASE will be all lit Use jog wheel 1 to select the page number of the chase S 1 20 3 Press the number button 1 20 to select the chase number the LEDs on BANK button will be all lit the LCD will show the number and parameter of CHASE BANK SCENE STEP FADE WAIT 1 20 MANUAL PROGRAM al m M3 4 Use the Jog wheel 1 to transfer to other Banks then press the number button 1 20 o select the scene to store the Chase Use the Jog wheel 3 to adjust the FADE TIM
26. components whatsoever inside only really high voltage that can give you a deadly shock Do not place objects containing fluids e g flower vases or beer bottles on or near the device Notice regarding disconnection from mains power To completely disconnect the device from mains power you must pull the plug from the power socket For this reason the device should be placed in a position where unobstructed access to the power socket is as sured at all times so that in an emergency you will be able to immediately pull out the plug To eliminate the risk of fire you should completely disconnect the power plug from the power socket when the device is not going to be used for a long time for example during holidays Always grasp the power cord by the plug Do not pull on the cord itself and never touch the power cord with wet hands as this could result in a short circuit or an electrical shock Do not place the device speakers or anything else on the power cord and make sure that it does not become clamped Never tie knots in the power cord and do not bind it together with other cables Lay the power cord so that no one can step on or stumble over it Adamaged power cord can cause a fire or an electrical shock Check the power cord from time to time Should it become damaged contact our customer service department to have it replaced Always operate the device only on a correctly earthed socket never sever the power cord s earth wire Otherwise a LIFE
27. d is on which means that you can start to operate the controller L Setting menu Entering the menu 1 Enter Program mode 2 Press ENTER MAIN MENU Button to enter LCD screen main menu ENTER MAIN MENU A Exiting from the menu Press ESC CLEAR button to exit from the last menu until exit from the Menu totally The main Menu including the following 17 settings Create a new Fixture Profile Modify a Fixture Profile Delete a Fixture Profile Patch a Fixture Reverse channel setup Fade mode setup Blackout mode select En gt ON Midi channel select o Chase run by inside outside time Auto remote address Read CF card Write CF card Modify Password LL sch M sesch gt o H 0 Enable Password Erase all memory O audio input range adjust lt N Channel value display mode You can select the Menu by Jog wheels and press ENTER MAIN MENU to enter sub Menus for editing MAIN MENU V LlCreateaneu fixture profile 1 Enter Menu Mode 2 Turn jog wheel 1 up to when the 01 Create a new Fixture is shown on the monitor press ENTER MAIN MENU Button to enter Use Jog wheel 2 and 4 to change the name of the FIXTURE Turn Jog wheel 2 to change the position of the cursor and Jog wheel 4 should be used to change the trait of the channel or character The amount of the letters must be below 26 it can be include ten numbers one the leng
28. emain subject to change without further notice Disposal Never throw the device into the regular household waste at the end of its useful life This product is subject to the European Directive 2002 96 EC Dispose of the device through an approved disposal centre or at your community waste facility Observe the current existing regulations In case of doubt contact your disposal facility The packaging is certified via a dual system Take all packaging materials to an environmentally friendly dis posal facility in compliance with the local regulations Si CE A STAIR 2Oll e Musikhaus Thomann K Treppendorf 30 e 96138 Burgebrach e Germany www thomann de
29. eps 2 6 to program other scenes 8 Press PROGRAM button for 3 seconds to exit Program mode the LED goes out indicating this selection PROGRAM 2 2 Program a scene with movement 1 20 1 Enter Program mode 2 Press the button 1 20 to select Fixture you can select several fixtures at a time by tapping of these buttons Move Faders 1 24 or use the CENTRE PRESET SCENE have saved to change the output of each channel press MOVEMENT button 1 40 4 Press the button 1 10 to select one MOVEMENT in ten the selected FIXTURE will run the MOVEMENT If it is necessary to adjust MOVEMENT parameter use Jog wheel 2 to select the adjusting MOVEMENT parameter options position amp range amp fade time or wait time amp loop use Jog wheel 3 4 to adjust parameter values 6 Repeat Steps 2 5to select MOVEMENT for other FIXTURE 7 Press MANUAL REC to store into memory all the LEDs on CUE OVERRIDE CENTRE FIXTURE GROUP PRESET CHASE BANK BLACKOUT blink to indicate this operation 8 Press BANK use Jog wheel 1 to select the BANK number to store the scene 9 Press the number button 1 20 to select the Scene number going to be saved all LEDs and the Segment Display will blink for three times briefly indicating this operation then the LCD will show the bank and the scene number of the programmed scene Repeat steps 2 9 to program other SCENEs with MOVEMENT 11 If you don t intend to continue your programming p
30. fixture wait for 3 seconds so_ the fixture can receive the signal of the controller and move all the motors to their home position 5 After 3 seconds use jog wheel 2 to select the fixtures of the first group and jog wheel 4 to select the fixtures of the second group When you turn the jog wheel 2 or 4 the cursor will switch between the first and second group The fixtures of this two group will be selected in turn and the unit will act differently when it be selected corresponding fixture will show on the LCD display it means the fixture s amount of the channel is as same as the corresponding number button s 7 Repeat 5 6 to set the address of other fixtures EI 6 Press number Button 1 20 all the LEDs will blink for 3 times the address of the Back to the last menu please press ESC CLEAR Button which under the root directory of CF card then you can read them out by this function And you have to patch the profile in order to use it normally Every time read the CF card please don t move it or the card or the files will be damaged The format of the CF card should be FAT else you have to convert it to FAT by PC and copy it to CF card 1 Enter Menu Mode Turn Jog wheel 1 up to when the 11 Read cf card is shown on the monitor Press ENTER MAIN MENU button to enter Use Jog wheel 1 to read the program file 01 Load program file or profile file 02 Load a fixture profile Press ENTER MAIN MENU
31. he monitor Press ENTER MAINMENU button to enter Use Jog wheel 1 to select use power password or use memory protect password press ENTER MAIN MENU button to enter 1 10 4 The LCD hint to input password use number button 1 10 to input 6 digit password Use Jog wheel 2 to select Enable or Disable Press ENTER MAIN MENU Button to enter all the LEDs blink for 3 times indicate that you have set successfully 7 Press ESC CLEAR Button to back to the last menu ESC CLEAR 1 15 Erase all memory 1 Enter Menu Mode 2 Turn Jog wheel 1 up to when the 15 Erase all memory shown on the monitor Press ENTER MAIN MENU button to enter 3 The LCD hint to input 6 digit memory protect password Input the exact password and Press ENTER MAIN MENU Button to delete the memory information You have to input the password again when it s wrong 4 Use Jog wheel 2 to select Yes delete and back to the last menu or No back to the last menu 1 Enter Menu Mode 2 Turn Jog wheel 1 up to when 16 Audio input range adjust shown on the monitor Press ENTER MAIN MENU Button top enter Use jog wheel 2 to choose the sensitivity of the sound 0 100 The bigger the number the higher the sensibility Then you can test the sensibility SS A PAN FINE Press ENTER MAIN MENU Button to store and back to the main menu back to the main menu without any change Press ESC CLEAR Button ENTER MAIN MENU 1 17 Channel v
32. ndicated by the lit LED Use Jog wheel 1 to select the bank number to edit the scene Press the number button 1 20 to open the scene you are going to copy Press MANUAL REC to store LEDs on CUE OVERRIDE CENTRE FIXTURE GROUP PRESET CHASE BANK BLACKOUT blink at the same time Press BANK Then use the Jog wheel 1 to select the BANK number to copy the scene Press the number button1 20 then copy the Scene to the right position All LEDs and the Segment Display will blink for three times briefly indicating this operation then the LCD will show the bank and the scene number of the programmed scene If you don t intend to continue your programming press and hold down the PROGRAM button for three seconds to exit Program mode the LED goes out indicating this selection 2 5 Delete a scene 1 Enter Program mode 2 Use the Jog wheel 1 to select the Bank number of the being deleted scene EX 3 Press the number button 1 20 to select the scene you are going to delete Press the button AUTO DEL Press the button BANK 1 20 6 Then press the number button 1 20 the scene will be deleted all LEDs and the Segment Display will blink for three times briefly indicating this operation then the LCD will show the bank and the scene number of the deleted scene 7 If you don t intend to continue your programming press and hold down the PROGRAM button for three seconds to exit Program mode the LED goes out indi
33. nds to exit Program mode the LED goes out indicating this operation PROGRAM 2 20 Override editing 1 Enter Program mode 2 Press OVERRIDE button 3 Press number Button 1 20 to select the Override number to be edited Press FIXTURE button Press the number button 1 20 to select the concerned fixtures to be edited with Override Use FADERS1 24 and 4 Jog wheels to adjust the selected fixture to your desired effect Press MANUAL REC button at this moment all LEDs on CUE OVERRIDE CENTRE FIXTURE GROUP PRESET CHASE BANK BLACKOUT blink at the same time Press OVERRIDE button Press the number button 1 20 to select the Override number you chose in step 2 all LEDs blink for 3 times to indicate that you have successfully edited an Override effect Press PROGRAM button for 3 seconds to exit Program mode the LED goes out indicating this operation Note If you press different buttons in step 3 and 9 the Override you set in step 3 will cover the one in step 9 e2 el Program a cue Enter Program mode Press CUE button use jog wheel 1 to select the page number Press the number button 1 20 to select the to be stored CUE number at this moment all LEDs on CHASE are lit and all LEDs on the number button which have saved CHASE will blink Turn jog wheel 1 should change the page number Press the number button 1 20 to select the Chase number which is to be stored to CUE the LEDs on the chosen
34. nts in sound activation mode it will process repeatedly as per the built in movement Loop time then enter next step 3 Auto Mode Press BANK Button Press AUTO DEL Button to enter auto mode the LED of AUTO DEL will on 3 Use Jog wheel 1 to select the bank you anticipate 4 Use Jog wheel 3 or 4 to adjust current FADE TIME or WAIT TIME or use TAP INSERT Button to adjust the speed of the scene TAP INSER T NOTE When you press TAP INSERT to adjust the speed adjusting the running speed of the scene is based on the interval of pressing the Press TAP INSERT Button twice which no more than 10 minutes 3 2 Run a program Please finish the program and scene before running the program 1 Auto Mode 1 Press CHASE Button use jog wheel 1 to select chase page CHASE 2 Press MANUAL REC to enter manual mode the LED of MANUAL REC will be on MANUAL A m 1 20 3 Press number Button 1 20 to select the program you anticipate e 2 Sound Mode music amp BANKCOPY AY 3 Auto Mode 1 CHASE Use Jog wheel 2 to run the last or next step Press CHASE Button use jog wheel 1 to select chase page Press MUSIC BANK COPY Button to enter sound mode the LED of MUSIC BANK COPY will be on Press number Button 1 20 to select the program you anticipate you can choose much more than one CHASE and they will run with the music on the train that you select them When it is
35. number buttons will be lit 5 Press MANUAL REC button all LEDs blink for 3 times to indicate that you have successfully stored a CUE 6 Repeat steps 4 6 to store more CUEs 7 Press PROGRAM button for 3 seconds to exit Program mode the LED goes out indicating this operation 1 Enter Program mode 2 Press CUE button use jog wheel 1 to select the page number 3 Press the number button 1 20 to select the to be edited CUE number at this moment all LEDs on CHASE are lit and all LEDs on the number button which have saved CHASE will blink Turn jog wheel 1 should change the page number En MANUAL PROGRAM 2 m Press the number button to edit the Chase in CUE Press MANUAL REC button all LEDs blink for 3 times to indicate that you have successfully edited a CUE Press PROGRAM button for 3 seconds to exit Program mode the LED goes out indicating this operation 2 23 Delete a cue CUE PROGRAM En Enter Program mode Press and hold AUTO DEL button Press CUE use jog wheel 1 to select the page number Then press the number button 1 20 all LEDs blink for 3 times to indicate that you have successfully deleted a CUE Press PROGRAM button for 3 seconds to exit Program mode the LED goes out indicating this operation 3 24 Store a blackout scene Blackout Scene is a special scene of Blackout mode set in By Black Scene 1 20 1 2 BLACK OUT STAND ALONE
36. ons to load or stored your scenes There are a maximum of 1200 programmable scenes Override the fixture fixtures when the show is running Select set the pan amp tilt centre Used to control manual operation or to record programs Activates Program mode Activates Music mode or to copy a bank of scenes Used to create a standard beat or insert a scene to chase Activates Auto mode or to delete scenes or chases Select Blackout Stand Alone two modes Connect to USB Light These faders are used to control the intensity CF card port can be used to upgrade software copy data and introduce to light bank Extra easy controllers Incorporated for Master Slave immediate pre programmed light shows Multi function number buttons 1 20 Function buttons The descriptions of the Function buttons Fixture Select 20 units of Fixtures Pls refer to the following table for Fixture addresses Fixture Group Set or select 20 Fixture Groups only 1 10 Select or operate 10 Movements 4 Preset 20 groups of fixtures can be set or selected by Jog wheel PAN 10 colour Preset 1 10 and 10 GOBO Preset 11 20 each group Set select or operate 60 Cues Set select or operate 60 Chases Set and select 20 Overrides Bank 60 banks each bank with 20scenes can be set and selected by Jog wheel 1 centre Set select and operate 20 Centers 10 Number 1 20 button 1 1 10 10 stand for 0 Number for setting and input ting password 2 1 10 10 MOVEMENT can be
37. ou have successfully store a Preset 9 Repeat Steps 2 8 to program more presets 10 Press the button PROGRAM for 3 seconds to exit Program mode the LED goes out indicating this operation 1 Enter Program mode 2 Press PRESET Button to select programming Preset state PRESET En FIXTURE EY PRESET Roll the Jog wheel 1 to select Preset groups 1 20 Press the number button 1 20 to open the to be edited preset Press FIXTURE button Press the number button 1 20 to select the concerned fixtures to program Preset Move FADER 1 24 to change COLOUR GOBO channel values The codes of the channel feature of ARRT CODE are C and G in the fixtures bank output for the convenience to check other channels but the channel output will not be stored in the preset Press MANUAL REC button at this moment all LEDs on CUE OVERRIDE CENTRE FIXTURE GROUP PRESET CHASE BANK BLACKOUT blink at the same time Press PRESET Button 1 20 10 Press number button 1 20 to select the opened Preset all LEDs blink for 3 times to indicate that you have successfully edited the Preset 11 Press PROGRAM button for 3 seconds to exit Program mode the LED goes out indicating this operation PROGRAM NOTE If you press different buttons in step 4 and 10 the preset in step 4 will cover the one in step 10 2 15 Programming a fixture group Enter Program mode Press FIXTURE button EX 3
38. ress and hold down the PROGRAM button for three seconds to exit Program mode the LED goes out indicating this selection PROGRAM 2 3 Program a scene 1 Enter Program mode 2 Press the button BANK to turn on its fader control which is indicated by the lit LED use Jog wheel 1 to select the bank number to edit the scene Press the number button 1 20 to open the scene you are going to edit Move Faders 1 24 or use the CENTRE PRESET SCENE have saved to change the output of each channel you can also use the Jog wheel 1 2 to adjust PAN PAN FINE or use Jog wheel 3 4to adjust TILT TILT FINE or press MOVEMENT to add MOVEMENT function Press MANUAL REC to store LEDs on CUE OVERRIDE CENTRE FIXTURE GROUP PRESET CHASE BANK BLACKOUT blink at the same time Press the button BANK Press the number button 1 20 to store the edited scene which will cover the former scenes all LEDs and the Segment Display will blink for three times briefly indicating this operation then the LCD will show the bank and the scene number of the programmed scene PROGRAM 8 Press the button PROGRAM for three second to exit Program mode the LED goes out indicating this selection Hint If you select different scenes at step 3 and 6 the editing scene would cover the scene at step 6 2 4 Copy a scene MANUAL ni PROGRAM Enter Program mode Press the button BANK to turn on its fader control which is i
39. th of the Fixture name should be below 16 and it must be begin with letter Press ENTER MAIN MENU button to change the trait of the channel ENTER MAIN MENU Y Use Jog wheel 2 and 4 to change the trait Turn Jog wheel 2 to change the position of the cursor and Jog wheel 4 to change the trait of the channel or characters Press ENTER MAIN MENU to enter ENTER MAIN MENU Y Use jog wheel 2 to select profile ACME LIBRARY or OTHER LIBRARY you want to store the fixture profile Press ENTER MAIN MENU button all LEDs blink for 3 times to indicate that you have successfully edited a FIXTURE PROFILE Repeat steps 3 4 to build 50 FIXTURE PROFILE mas MAIN MENU 4 10 Back to the last menu please press ESC CLEAR button 1 2 Modify a fixture profile ENTER MAIN MENU 4 MAIN MENU 4 1 Turn jog wheel 1 up to when the 02 Modif a Fixture is shown on the monitor press Enter Menu Mode ENTER MAIN MENU Button to enter Use Jog wheel 3 to chose the bank of other manufacturers and Jog wheel 4 to chose the ACME s Press ENTER MAIN MENU button to enter Use Jog wheel 2 and 4 to change the name of the FIXTURE Turn Jog wheel 2 to change the position of the cursor and Jog wheel 4 should change the trait of the channel The amount of the letters must be below 26 it can be include ten numbers one the length of the Fixture name should be below 16 and it m
40. th short run time will repeat automatically 3 4 Over control Using over control to change the effect specially you can operate some units solely when the CUE or CHASE or BANK running There are two ways to operate FIXTURE OVERRIDE 1 20 A When CUE or CHASE or BANK running press OVERRIDE button Then press FIXTURE button and use number button 1 20 to choose light so you can push the handspike to change the effect 8 When CUE or CHASE or BANK running press OVERRIDE button then use 1 20 button to open the effect that be programmed 1 20 OVERRIDE e 4 Fog machine operation Set up another 481CH DMX signal to control the fog machine keep out the 482CH Fog Machine operation 1 Connection connect the fog machine with the DMX information 2 Setting Keep the power on hold the FOG MACHINE button the press PROGRAM button to enter the output menu Use 2 or 3 or 4 to setup duration set 1 100S or interval set 0 200S or volume out 0 255 Press ENTER MAIN MENU button to store Press PROGRAM button to exit 3 Control The fog machine work as it s set in normal Press FOG MACHINE button to output maximal fog set 481CH output to be 255 5 Strobe light operation Set up 483 484CH address in the DMX signal to control the strobe light channel Operation 1 Connection connect the strobe light with the DMX information 2 Setting keep the power on hold the STROBE button press PROGRAM button to
41. ton PROGRAM for three seconds to exit Program mode the LED goes out indicating this selection PROGRAM 2 9 Program a step 1 Enter Program mode 2 Press the button CHASE use jog wheel 1 to select the page number of the chase to select the program 1 20 3 Press the number button 1 20 to select the Chase number LEDs on the BANK button will be all lit the LCD will show the number and parameter of the CHASE BANK SCENE STEP FADE WAIT Use Jog wheel 2 to view the steps the strobe display 002 indicate programmable step number Use jog wheel 1 to select the bank number of the scene press number button 1 20 to open Use the Jog wheel 3 4 to adjust the FADE TIME and WAIT TIME which are going to be added to the single Chase If you do not make any adjustments the system will remember the last FADE TIME or WAIT TIME 7 Press the button MANUAL REC all LEDs blink for 3 times to indicate that you have successfully programmed a step 8 Repeat steps 2 3 to select other steps Press the button CHASE to store and exit the programming state 10 Press the button PROGRAM for 3 seconds to exit Program mode the LED goes out indicating this operation PROGRAM 2 10 Insert steps into a chase 1 Enter Program mode 2 Press the button CHASE use jog wheel 1 to select the page number choose the programming chase Use the Jog wheel 2 to select the position of inserted steps EN 3 Press the
42. ust be begin with letters Press ENTER MAIN MENU Button to change the trait of the channel Use Jog wheel 2 and 4 to change the name of the FIXTURE Turn Jog wheel 2 to change the position of the cursor and Jog wheel 4 should change the trait of the channel 8 9 Repeat 3 7 to change other FIXTURE PROFILE Back to the last menu please press ESC CLEAR button 1 3 Delete a fixture profile ENTER MAIN MENU V ENTER MAIN MENU V 1 2 Enter Menu Mode Turn jog wheel 1 up to when the 3 DELETE A FIXTURE is shown on the monitor Then press ENTER MAIN MENU button to enter Use Jog wheel 3 to delete the profile of other manufacturers and Jog wheel 4 to delete the ACME s Press ENTER MAIN MENU Button to enter and LCD will show NO Turn Jog wheel 1 to chose Yes Press ENTER MAIN MENU Button all LEDs shaking for 3 times means success Repeat 3 6 to delete other FIXTURE PROFILE Back to the last menu please press ESC CLEAR button 1 4 Patch a fixture 1 Enter Menu Mode 2 Turn Jog wheel 1 up to when the 04 Patch a Fixture is shown on the monitor Press ENTER MAIN MENU Button to enter ENTER MAIN MEN El 3 Press number Button 1 20 to chose the fixture which needs to patch 4 Turn Jog wheel 3 to chose the profile of other manufacturers and Jog wheel 4 to chose ACME s 5 Press ENTER MAIN MENU Button to enter all the LEDs strobe for 3 times
43. y your new equipment and make sure to read this manual carefully before operation Features gt 2x DMX Outputs 484 DMX Channels in total including 481Ch for DMX fog 482Ch for future use 483 484Ch for DMX strobe Fixture Library for built in ACME lighting fixtures Other brand fixtures can be set manually but Max with 50 fixtures gt Built in 10 MOVEMENTS Can adjust PAN TILT Position PAN TILT Range Fade time or Wait time LOOP 60 Programmable Chases each chase can have 200 scenes max 1200 Programmable Scenes 60 banks x 20 scenes 400 Programmable Presets 20 presets each preset has 10 colours and 10 gobos gt Control 20 DMX light fixtures and each fixture up to 24 Channels gt Operate 20 Fixture groups simultaneously gt 24 faders for controlling 24 DMX channels 60 x CUEs Combined many chases together and operate the chases at the same tine 20 x override Can assign one or more than one of the fixtures to perform special function like follow spot during the operation 20 overrides can be set in the controller 20 x Centre Can set each fixture s central position of the movement you can set up to 20 centre positions gt Remote DMX Addressing only for ACME lights Blackout mode 1 Standby 2 PAN TILT Centre Position 3 Blackout Scene Can use jog wheel to adjust the audio sensitivity LCD display will indicate the value Can set Password to boot the controller gt
Download Pdf Manuals
Related Search