Manual - AVOLITES
Contents
1. 250W USER MANUAL Please read over this manual before operation the light 1 Open the box and checking Pagel 2 Safety instructions Pagel 3 determinations 2 4 Description of the device Page3 5 Installion 4 6 Control Board Operation 7 DMX512 Channel Function Pages 8 Technical specifications 14 9 Beampath 15 10 ELECTRICAL DIAGRAM Page16 11 COMMEN FAULTY MAINTAIN 17 12 Maintenance and cleaning ee 19 1 Open the box and checking Congratulations on choosing our products Please carefully read2. gt Do not switch the fixture on and off in short intervals as this would reduce the lamp life gt During the initial start up some smoke or smell may arise This isa normal process and does not necessarily mean that the device is defective gt Do not touch the device s housing bare hands during its operation housing becomes hot gt For replacement use lamps and fuses of same type and rating only CAUTION EYE DAMAGES Avoid looking directly into the light source meant especially for epileptics 3 Operating determinations gt This device isa moving head spot for creating decorative effects and was designed for indoor use only gt If the device has been exposed to drastic temperature fluctuation e g After transport ation do not switch it onimmediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature gt Never run the device without lamp gt Do not shake the device Avoid brute force when installing or operating the device gt Never lift the fixture by holding it at the projector head as the mechanics may be damaged Always hold thefixture at the transport handles gt When choosing the installation spot please make sure that the device is not exposed to extreme heat moistureor dust There should not be any cables lying around You endanger your own and the safety of others gt The minimum distance between light output and the il
3. change the power supply settings see the chapter Appendix Connect the fixture to the mains with the enclosed power cable and plug The earth has to be connected The occupation of the connection cables is as follows Cable EU Cable US International Brown Black Live L Light blue White Neutral N Yellow Green Green Earth 5 5 DMX 512 connection connection between fixtures Only usea stereo shielded cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Occupation of the XLR connection DMX OUTPUT DMX input XLR mounting socket XLR mounting plug 1 Ground 2 Signal 2 Signal 3 Signal 3 Signal Caution At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 resistor between Signal and Signal into a 3 pin XLR plug and plug itin the DMX output of the last fixture The transform of the controller line of 3 pins and 5 pins plug and socket SPins canon socket Pin 1 GND SCREEN 3Pins canon plug Pin 2 Signal Pin 1 GND SCREEN Pin 3 Signal Pin 2 Signal Pin 4 Pin 3 Signal Pin 5 SPins canon plug Pin 1 GND SCREEN Pin 2 Signal Pin 3 Signal Pin 4 N C Pin 5 NIC 3Pins canon socket Pin 1 GND SCREEN Pin 2 Signal Pin 3 Signal 6 Control board Operation Control board Fu
4. this instruction manual in its entirety and keep it well for using reference This manual contained about the installation and the relative using information of this products Please according to this manual s relative speaking when using this equipment This equipment was made of new style high intensity plastic It fully shows the modem times light characteristic with beauty structure And it was made according to CE standard Fully up the international standard of DMX512 agreement Master or slave in phase control Can be use in large entertainment theater performing and playing hall etc This product uses MSR 250 2 electrical arc lamp When receiving this product please carefully bring and put and check that whether this equipment has been damaged or not during transportation And please also check the following thing was enclosed Signal line piece Safety string one pieces User Manual one set 2 Safety instructions Every person involved with installation and maintenance of this device have to be qualilfied follow the instructions of this manual CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START UP Be careful with your operations With a high voltage you can suffer a dangerous electric shock when touching the wires This device has le
5. 50 TEMPERATURE SWITCHBFAULTY NO LIGHT FROM BULB BALLAST FAULTY 250W BALLAST 06 03 7 025 00 MAIN BOARD FAULTY MAIN PCB 26 2A 2107XY 00 SHOW BOARD FAULTY SHOW BOARD 26 2A 2107D1 00 TRANSFORMER 110V 06 00 B006 00 TRANSFORMER 230V 06 00 8002 00 aan oie REALY OF MAIN BOARD FAULTY REALY FAULTY 11 01 0002 00 MAIN BOARD OPTCOOUPLER FAUTLY _ 4N25 OPTOCOUPLER oo an2s o0 BULB LIGHTING AND WHOLE FAN ON HEAD OF LIGHT FAULTY 80x80x25 12VDC FAN 16 00 0008 04 LIGHT NORMAL BUT FANS CAN NOT WORK FAN ON BOTTOM OF LIGHT FAULTY 25 12VDCFAN 16 00 0008 04 SHOW BOARD FAULTY SHOW BOARD FAULTY 26 2A 2108D1 00 COMPLETE LIGHT RESEAT BUT NOT BECONTROLLED WHETHER THE SIGNAL CABLE GOOD METERS CABLE SETS 27 04 0010 00 MOTOR FOR PAN FAULTY 23HS0001 02MOTOR CAN NOT ADJEST PAN 420HTD GT 3M ORRPP3 STRAP OF PAN BREAK WEIGHT6mm MOTOR FORTILTFAULTY 23HS0001 02MOTOR 447HTD GT 3M ORRPP3 WEIGHT6mm MOTOR FOR COLOR WHEEL FAULTY 42BYGH026 2MOTOR 0073 00 TRANSFORMER FAULTY AL EFFECT WHEEL CAN NOT ROTATION CAN NOT DIMMER STROBE CAN NOT WORK AUTOMATISM 17 9 Maintenance and cleaning It is absolutely essential that the fixture is kept clean and that dust dirt and smoke fluid residues must not buildup on or within the fixture Otherwise the fixtures light output will be significantly reduced Regular cleaning willnot only ensure the maximum lig
6. ft our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes writtenin this manual Important gt The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device gt Please consider that damages caused by manual modifications to the device are not subject to warranty gt Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution gt Make sure that the available voltage is not higher than stated on the rear panel gt Always plug in the power plug least Make sure that the power switch is set to OFF position before you connect the device to the mains The power plug has to be accessable after installing the device gt Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the powercord from time to time NN NY gt by the plug Never pull out the plug by tugging the power cord gt This device falls under protection class I Therefore it is essential to connect the yellow green conductor to earth gt The electric connection repairs and servicing must be carried out by a qualified employee gt Do not connect this device to a dimmer pack
7. g anti clockwise 2 Remove the old fuse from the fuseholder 3 Install the new fuse in the fuseholder 4 Replace the fuseholder in the housing and fix it 19
8. ht output but will also allow the fixture to function reliably throughout its life A soft lint free cloth moistened with any good glass cleaning fluid is recommended under no circumstances should alcohol or solvents be used DANGER Disconnect from the mains before starting anymaintenance work The front objective lens will require weekly cleaning as smoke fluid tends to building up residues reducing thelight output very quickly The cooling fans should be cleaned monthly The gobos may be cleaned witha soft brush The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air jet The dichroic colour filters the gobo wheel and the internal lenses should be cleaned monthly To ensure a proper function of the gobo wheel we recommend lubrication in six month intervals The quantity of oil must not be excessive in order to avoid that oil runs out when the gobo wheel rotates There are serviceable parts inside the device except forthe lamp and the fuse Please refer to the instructions under Fitting Exchanging the lamp Maintenance and service operations are only to be carried out by authorized dealers Replacing the fuse If the lamp burns out the fine wire fuse of the device might fuse too Only replace the fuse fuse of same type and rating Before replacing the fuse unplug mains lead Procedure 1 Unscrew the fuseholder on the rear panel of the base witha fitting screwdriver from the housin
9. ive national norms during the installation The installation must only be carried out by an authorized dealer gt The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation gt The installation must always be secured with a secondary safety attachment e g appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails gt When rigging derigging or servicing the fixture staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden gt The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time gt The operator has to make sure that safety relating and machine technical installations are approved by an expert after every four year in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year gt The projector should be installed outside areas where persons may walk by be seated gt IMPORTANT OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE including but not limited to calculating working load limits in
10. luminated surface must be more than 2 meters gt Make sure that the area below the installation place is blocked when rigging derigging or servicing the fixture Always fix the fixture with an appropriate safety rope Fix the safety rope at the correct holes only gt Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened gt The lamp must never be ignited if the objective lens or any housing cover is open as discharge lamps mayexplose and emit a high ultraviolet radiation which may cause burns gt The maximum ambient temperature ta 45 C must never be exceeded Otherwise the lamp is switched off andthe fixture is out of operation for 5 minutes 4 Description of the device 1 Moving head 2 Yoke 3 Carry handles 4 Base Rear panel _ 5 Power switch 6 DMX output 7 DMX input 8 Power cord 9 Fuse holder Front panel 10 Mode button 11 Enter button 12 Up button 13 Down button 14 Display 12 13 eee 5 Installion 5 1 Fitting the lamp To insert the lamp MSR 250 2 loosen the lamp cover at the rear of head see the drawings by remowing the 3 fastening screws which are marked X Y Z Carefully pull out the cover with the lamp socketassembly If changing the lamp remove the old lamp from the socket Insert the lamp to the socket Do not install a lamp with a higher wattage lamp like thi
11. nction MODE FUNCTION Pan Pan movement in positive or negative direction CONDITION YES negative direction Vertical movement in positive or negative direction YES negative direction Addr Address code set ESt Reset run Working mode YES reset OFF DMX512 mode Automatic SLAE Slave mode on __ Lamp on LANP Lamp switch OFF Lamp off VE Software version HEAE Lamp hot LA Er Lamp error CHANNEL 1 PAN CHANNEL 2 TILT Value CHANNELS Speed of PAN TILT movement BIND Slow ar Fast CHANNEL 6 Lamp on off amp reset Value Yo Effect 255 100 Slow o o Fast Effect 240 255 94 100 No function 230 239 9053 Lamp offafter 3 seconds 140 229 55 89 No function Lamp on after 128 139 50 54 3 seconds Reset 0 49 No function Beampath Min beam angle 8 Min beam angle 8 8 5 8 20 Distance m 7 77 Diameter m Foot candles 1 0 8 06 04 0 2 0 02 04 06 08 1 Diameter m 15 COMMEN FAULTY MAINTAIN FAULTY FAULTY ANALYSIS FAULTY PART PLUG CABLE 27 00 0010 04 POWER PLUG LOOSE POWER SWITCH F AULITY POWER SWITCH REACH THE LIFESPAN OR BED 07 QUALITY OF BULB TRIGGER FAULTY B ELECTRONIC TRIGGER 10 2
12. s generates temperatures the device is not de signed for Damages caused by non observance are not subject to warranty Please follow the lamp manufacturer notes Do not touch the glass bulb with bare hands during the installation Make sure that thelamp is installed tightly into the lampholder system Reclose the lamp cover and tighten the 3 screws Lamp assembly Lamp assembly Do not operate this fixture with opened housing cover 5 2 Lamp adjust The WASH 250 lampholder is aligned at the factory Due to differences between lamps fine adjustment may improve light performance Strike the lamp open the shutter and the iris set the dimmer intensity onto 100 and focus the light ona flatsurface wall Center a hot spot the brightest part of the image by using the 3 adjustment screws A B C Turnone screw after another a quarter turn clokwise counter clokwise Ifyou cannot detect the hot spot adjust the lamp until the lightis evenly distributed Fron DY turning so eur pi 5709 3 adjustment screws A B C 5 3 Adjusting beam angle The Fresnel lens system can be configured inthe rangebetween Adjusting screw 8 and 22 Toset the desired 7 beam angle and loose 2 adjusting screws onthe Fresnel lens unit Fresnel lens and adjust the required beam angle Tighten the adjusting screws again and fix back the front cover EY Ih 5 4 Rigging the fixture DANGER TO LIFE Please consider the respect
13. stallation material being used and periodic safety inspection of all installationmaterial and the projector If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property gt The projector has to be installed out of the reach of people gt If the projector shall be lowered from the ceiling or high joists professional trussing systems have to be used The projector must never be fixed swinging freely in the room gt Caution Projectors may cause severe injuries when crashing down If you have doubts concerning the safety of possible installation do NOT install the projector gt Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector s weight gt The projector can be placed directly on the stage floor or rigged in any orientation ona truss without altering its operation characteristics gt For overhead use always install safety rope that can hold at least 10 times the weight of the fixture You must only use safety ropes with screw on carabines Pull the safety rope through the two apertures on the bottom of the base and over the trussing system etc Insert the end in the carabine and tighten the fixation screw Secure chain 5 5 Connection to the mains Verify the power supply settings before applying power If you wish to
Download Pdf Manuals
Related Search