Eclipse X34 Quick Start Guide
Contents
1. Select an option e Automatically connect to the device When the application is started or when the named device appears on the network while the application is running on this computer the application will try to connect to the named device e Ask if want to connect to the device When the application is started or when the named device appears on the network while the application is running on this computer the application will display a message box allowing you to connect to the named device e Take no action When you start the application or when the named device appears on the network while the application is running on this computer you must connect manually to use the named device When you close the application on this computer or you perform manual disconnect the application disconnects from the device 4 Press OK in the Connection Properties dialog After you finish the connect procedure the Eclipse X34 to which you have connected is marked as Ready and you can use it for recording Note Analyzer Devices Location Status 172 16 126 193 Device T Eclipse X24 SN 1 2692 Eclipse X24SN12665 172 16 128 137 Locked by power qa Update Device Eclipse X24SN712654 172 16 128 235 Ready to connect ipdate License Dieeannect Note To disconnect from a device display this dialog select the device and click the Disconnect button Note Eclipse X34 will not appear in the Analyzer Device dialog if2. to System under Test using an Interposer or Probe For an SMA Probe Interposer do the following 1 Connect the SMA Cables between the two Devices under test so that the data paths travel through the appropriate connections on the SMA Probe 2 Connect power to the interposer using the provided 12 V power adapter For a multi lead probe or other types of probes and interposers please see the User Manual 10 2 o ne o 0 Configure Recording Options 1 From the Setup menu select Recording Options 2 Select the General tab and then choose Eclipse X34 as the Analyzer type 3 Inthe Link section specify the lane width of the MPHY link to be analyzed The rest of the settings in this section can be left at the factory defaults for most MPHY systems 4 For multi lane links the Analyzer needs to observe link training to record link traffic correctly 5 Click OK at the bottom of the Recording Options dialog box to apply the Analyzer recording settings specified Start Recording 1 Start a recording session by clicking the Record button in the toolbar Recording is tracked and reported on an activity meter in the status bar 2 After the recording buffer fills uploading starts automatically The MPHY traffic is saved to the hard drive as the file specified in the recording options and this file is opened in the application for you to view the traffic Note You can interrupt a sess
3. Probe Supports lane widths from x1 to x4 at data rates for GEAR1 2 3 on the X34 system SMA Interposer Supports lane widths from x1 to x4 at data rates for GEAR1 2 3 Warning Interposer has static sensitive components Handle only at static safe work stations 6 Installing the Software The software operates all of Teledyne LeCroy s PCI Express Protocol Analyzer and Exerciser products and should be installed on a Microsoft Windows based host machine You need to install the software on the host machine before attaching the X34 Analyzer to the system The software suite corresponds to the M PHY technology you chose at purchase time If you selected M PCle you will use the PCle Protocol Suite For SSIC this would be USB Protocol Suite and so on The minimum requirements for the host machine are e Microsoft Windows 8 Windows Server 2012 Windows 7 Windows Server 2008R2 Windows XP operating systems e 2 GB of RAM e Storage with at least 200MB of free space for the installation of the software and additional space for recorded data e Display with resolution of at least 1024x768 with at least 16 bit color depth e USB2 0 port and or 100 1000Mbps Ethernet network interface For optimal performance please refer to our recommended configuration in the product documentation In general the higher the performance of the host machine the better user experience you get Please refer to the Readme notes and User Manual for recommend
4. The Analyzer has the following features on the front 1 Power LED Lights when power is On 2 Status LED Displays the connection status of the link Red Error condition Try using the application to clear the error Please contact the factory if this does not work Green Configuring system Blue Unit ready connected 3 Trigger LED Lights when Eclipse X34 triggers on an event 4 Ref Clk In Reference Clock In Provides an optional alternative connection from an external reference clock source to the Eclipse X34 analyzer Upstream direction Note In standard configuration the Eclipse X34 analyzer uses the reference clock from a probe cable from the interposer 5 GEAR LEDs Indicates current gear the analyzer is using for the Upstream direction Green Detected Speed 6 Upstream 3 0 LEDs Indicates which Upstream Lanes are currently showing activity Green Activity detected with no error Orange Activity detected with error Blank No activity detected 7 Upstream 3 0 and Downstream 3 0 connector Connection to the probe for the capture of both upstream and downstream directions of the link 8 Downstream 3 0 LEDs Indicates which Downstream Lanes are currently showing activity 9 Gear LEDs Indicates current gear the analyzer is using for the Downstream direction 10 Ref Clk In Reference Clock In Provides an optional alternative connection from an external referen
5. ce clock source to the Eclipse X34 analyzer Downstream direction Note In standard configuration the Eclipse X34 analyzer uses the reference clock from a probe cable from the interposer 11 Trigger In and Out Provide external trigger capabilities You can configure Eclipse X34 to trigger external equipment using Trigger Out You can use Trigger In to trigger the Analyzer from another device Rear Panel Description Teledyne LeCroy M PHY GEAR 1 2 3 Protocol Analyzer Eclipse X Model 923922 00 om DC IN 12V 8A 1 2 3 4 5 6 The rear panel of the Analyzer has 1 x8 Expansion Used to connect two X34 systems using a special cable to record X8 traffic 2 Sync Data Use a special cable to allow multiple Teledyne LeCroy analyzers to send synchronization and control messages to one another This connection is also required for x8 Expansion 3 Ethernet Port 1 GIGE Connectivity allows connection to the analyzer through an Ethernet network teledynelecroy com x8 Expansion Sync Data PEO k 4 USB Type B Host Machine Connector To connect the Analyzer to the host machine using a USB connection 5 DC IN 12V 8A 6 Power Switch black 1 On and 0 Off Warning Do not open the enclosure No operator serviceable parts are inside 5 Interposers and Probes The Eclipse X34 supports a full range of Teledyne LeCroy MPHY Interposers and Probes including Multi lead
6. ed configurations and additional information User manuals for your Teledyne LeCroy MPHY products can be found in Start gt All Programs gt LeCroy gt XXX Protocol Suite gt XXX Protocol Suite Note XXX Protocol Suite is dependent on the software package suite the customer orders with the Eclipse X34 To install the software follow the steps below Insert the CD into the CD ROM drive of the host machine that will control the Analyzer The installation window opens and displays 1 links to the software installation user manuals application notes and data sheets 2 Select Install XXX Protocol Suite and follow the on screen instructions The software installs automatically on the host machine s hard disk During installation all necessary USB drivers will be installed 3 To start the application launch the software program from the Start menu Start gt All Programs gt LeCroy gt XXX Protocol Suite gt XXX Protocol Suite Software installation can also be downloaded from the Teledyne LeCroy website 7 Setting Up and Connecting the Eclipse X34 Analyzer You can connect the Analyzer to the host machine using USB or Ethernet Using an Ethernet Connection To set up the Analyzer using an Ethernet connection 1 2 3 4 Install software on the host machine Connect the Analyzer to a 100 volt to 240 volt 50 Hz to 60 Hz 120 W power outlet using the provided power cord Connect the Ethernet cable between the Etherne
7. ion by pressing the Stop button If Recording is finished and Upload has started but has not finished a message box appears You can e Continue uploading e Abort the upload and flush the data e Abort the upload and preserve all the previously saved data Teledyne LeCroy Customer Support Mail 3385 Scott Blvd Santa Clara CA 95054 3115 Online Download Web _ teledynelecroy com Support SoftwareDownload Periodically check the Teledyne LeCroy Protocol Solutions Group E mail psgsupport teledynelecroy com web site for software updates and other support related to this Tel 800 909 7112 USA and Canada product Software updates are available to users with a current Tel 408 653 1260 worldwide Maintenance Agreement Fax 408 727 6622 worldwide Trademarks and Servicemarks Changes Product specifications are subject to change without notice Pe re te eee Teledyne LeCroy reserves the right to revise the information in this LeCroy Microsoft and Windows are registered trademarks of Microsoft Inc All other trademarks are property of their respective document without notice or penalty companies 2014 Teledyne LeCroy Inc All rights reserved Part Number 925030 00 Rev B This document may be printed and reproduced without additional permission but all copies should contain this copyright notice
8. it is connected on a different Subnet on your local network You can connect to it on the Subnet by specifying its IP address in the Add Device dialog Using a USB Connection 5 Eclipse X34 will be recognized by the host machine as a USB To set up the Analyzer using a USB connection device 1 inetalicataare on e G nae Follow the Microsoft Windows on screen Plug and Play 2 Connect the Analyzer to the 12 volt DC Adaptor provided in instructions for the automatic installation of the Analyzer as a the box USB device on your analyzing host machine The required 3 Connect the USB port to a USB port on the host machine USB drivers are included on the Installation CD and were using a USB cable installed on your system when you installed the software 4 Turnon the power switch on the back of the Analyzer Click Finish when you see the message that says Windows Note At power on the Analyzer initializes and performs a has finished installing the software that your new hardware self diagnostic If failure occurs call Teledyne LeCroy requires and the file has been installed in your host machine Customer Support for EN 6 Start the software so you can start working with Eclipse X34 8 Making Your First Recording Connect Eclipse X34 to the system under test using an interposer or probe and then configure the Recording Options You can then test the Analyzer by creating a short snapshot recording Connect Eclipse X34
9. t port on the Analyzer and a Ethernet port in the local network Turn on the power switch on the front of the analyzer Note 1 No driver installation is needed for Eclipse X34 to operate over a network Note 2 Eclipse X34 is configured at the factory to use dynamic IP setting and will get all required network parameters from the DHCP server on your network If the DHCP server is not available or to connect Eclipse X34 directly to the host machine you can reconfigure the network settings of Eclipse X34 using the menus in the LCD display on the front of the analyzer see the LCD Menus part of section 4 of this document Connecting to Eclipse X34 in the software Start the software and perform the following procedure to connect to a Eclipse X34 analyzer over the network 1 Select the Setup gt All connected devices menu in the application to display the Analyzer Devices dialog About Analyzer Devices Status Ready to connect Location 172 16 134 1 Device Eclipse x34 SN 12692 Update Device Update License The Eclipse devices in the list are marked m e Locked Some other client on the network is already connected to that device e Ready to connect Available for connection 2 Select your Eclipse X34 device in the list and press the Connect button to execute the connection procedure After the connection is established the application displays the Connection Properties dialog 3
10. wa TELEDYNE LECROY Everywhereyoulook F Eclipse X34 MIPI M PHY Protocol Analyzer Quick Start 1 Introduction Use this document for quick installation and setup If you experience problems or need more information see the User Manual on the Installation CD or at the Teledyne LeCroy web site 2 Components The analyzer package includes the following components e Eclipse X34 analyzer system e DC Power Adapter 12 volts and AC power cable e USB cable e Teledyne LeCroy Equipment Carrying Pouch e Software program CD ROM Lclipse XIA Y GEAR 1 2 3 3 M PH Please see the Eclipse X34 User Manual on the installation CD for component specifications and further details There is a version of this manual on the CD that corresponds to the M PHY technology you chose M PCle SSIC etc Each purchased M PHY technology M PCle SSIC etc Eclipse X34 Protocol Analyzer ships with a CD ROM that corresponds to that technology 3 Unpacking the Analyzer Inspect the received shipping container for any damage Unpack the container and account for each of the system components listed on the accompanying packing list Visually inspect each component for absence of damage In the event of damage notify the shipper and Teledyne LeCroy Retain all shipping materials for shipper s inspection 4 Front Panel Description LSI PSC XNFF M PHY GEAR 1 2 3 ER 123 45 6 7 8 9 10 11
Download Pdf Manuals
Related Search