Extra Transmitter User Manual
Contents
1. There are 2 methods to teach the module brain the transmitter code 1 REMOTE TRANSMITTER CODE LEARNING WITHOUT ACCESSING THE MODULE Some DesignTech Remote Starters have a special feature that allows new transmitters to be taught without accessing the module under the dash 1 Turn ignition key ON then OFF Do not start the vehicle Flip control toggle switch OFF then ON Slowly push the brake pedal TWICE dash lights will turn on for 2 seconds Flip control toggle switch OFF then ON while dash lights are on for the 2 sec onds PUSH and HOLD the q button on the transmitter The dash lights will turn on then off to signal the code has been learned Teach other transmitters Repeat steps 5 and 6 Dash lights will turn on and off four times to signal the exit of the programming mode 2 TRANSMITTER CODE LEARNING AT THE MODULE The module is often be located under the driver s side of the dash mounted above the pedal controls The module is 9 long by 2 wide with two push buttons and one LED on the side 1 Turn the Control Switch ON 2 Push the RED button to the right of the red LED The red LED and the dash lights will come on for a second The remote starter powers the ignition and accessory wires 3 Hold down the A button on the transmitter until the red LED and the dash lights come on again for a second The module has now learned the transmitter code Re lease the transmitter button 4 To learn additio2. nal transmitters up to 3 more immediately within 5 seconds push and hold the gaa button on another transmitter until the red LED and the dash lights come on for a second again 5 Wait 10 seconds after the last transmitter was taught to the unit the LED ignition and accessories will flash 4 times signaling that the unit has exited code Learning Note Teaching the module a new transmitter code will erase all previous codes so all transmitters must be taught at the same time You have only 5 seconds between transmitters to begin teaching a new transmitter PARA PPN Note Teaching the module a new transmitter code will erase all previous codes so all transmitters must be taught at the same time HELP LINE For any assistance regarding this product you may call DesignTech on our toll free telephone number 800 337 4468 Additional transmitters can be purchased directly through your local dealer or DesignTech at the address below All prices include shipping and handling Retail Pricing Five button transmitters 24471 69 95 Replacement Lithium Battery CR2032 20059 7 95 This device complies with FCC Rules Part 15 Operation is subject to two conditions 1 This device may not cause harmful interference and 2 it must accept any interference received including that which may cause undesirable operation FCC ID ELGTRAN2 or ELGTX4 CANADA 1476 102 320 or 14761021029 v0 1 Extra Transmitter User Manual Thank you for p
3. s important to remember to shift the transmitter accordingly before pushing the START button s Button to teach the transmitter to the unit NOTE These transmitters will only work with DesignTech remote starters a DesignTech 7 INTERNATIONAL INC 7955 Cameron Brown Court Springfield Virginia 22153 USA Tel 1 800 337 4468 Fax 703 866 2001 www designtech intl com
4. urchasing an additional transmitter from DesignTech Interna tional Your transmitter has the following special features e These transmitters have a special SHIFT feature the Ga ae button which allows control of four separate vehicles with one single transmitter Anti Scan technology to prevent copying e Three color LED to confirm function and transmission verification e Uses one 3 volt lithium battery CR2032 easily obtained at Radio Shack Catalogue 23 162 or DesignTech Catalogue 20059 To control the First vehicle simply push the button on the transmitter to control the desired function lt for Start D for Lights a for Lock and for a unlock To control the Second vehicle when the a l k button is pushed and while the colored LED light on the transmitter Aea between RED and GREEN push the button on the transmitter to control the desired function To control the Third vehicle when the a button is pushed a second time and while the colored LED light on the transmitter blinks RED push the button on the transmitter to control the desired function To control the Forth vehicle when the eS button is pushed a third time and while the colored LED light on the transmitter blinks GREEN push the button on the transmitter to control the desired function After the LED stops flashing the transmitter goes back to controlling vehicle 1 When teaching the same transmitter to several different vehicles it i
Download Pdf Manuals
Related Search