Downolad User Manual pdf
Contents
1. DHCP IP Address 921680096 ti stst s sS O Gateway 19216810100 OW O Subnet Mask 552552550 1 O Primary DNS 9216810240 O Secondary DNS f192 168 10 100 Save Config Copyright amp 2012 Arteco Motion Tech srl There are several fields in this page all of which can be changed by the user MAC Address HOST NAME Enable DHCP itis the hardware address of the module Do not change this value unless you are sure of what you are doing because the value shown is unique to your board and changing it cal lead to malfunctions Restoring the board either by the restore factory settings page or by the dip switch on the rear of the module will also restore original value this is a name of your choice that will be displayed in every page and also in the feedback window see the Ethernet I O module CGI Commands Interface manual for details It can be useful if you are operating on several modules at the same time to make sure of the module you are connected to this checkbox can be activatd to obtain dynamic IP parameters from a DHCP server if available on the network When this option is selected the other network parameters are shadowed as you can no longer set them unless you uncheck it IP Address if you do not have a DHCP server available on your network you can enter here an unused IP address of your local network Be aware not to 11 ETHERNET I O MODUL2. OFF output 5 OFF output 6 OFF output 7 p 12 ETHERNET I O MODULE USERS MANUAL This is a self explaining page here you can read the status of the input channels and set reset any output by clicking on the ON or OFF output labels Please note that if you have changed the default i o names with others of your choice they will be shown here instead of the default ones Input are automatically refreshed about every 500 mS Next option of the list is Restore factory settings arteco motion control technologies Hostname ARTECONET Arteco Ethernet digital I O module Module Reset I O setu i i This will cancel ALL of your settings and restore module factory defaults Network setu di Re enter your username and password 1 0 monitor Then click RESTORE to proceed Restore factory settings Change password username password Ddns service Firmware upgrade RESTORE Copyright 2012 Arteco Motion Tech srl As you can see you will be required here for safety to enter username and password again 13 ETHERNET I O MODULE USERS MANUAL Click restore when done and you will be redirected to the remaining of the procedure arteco Emir Se stil motion control technologies Hostname ARTECONET Arteco Ethernet digital I O module Module Reset 1 0 setup All module settings wil
3. of adequate rating should also be connected between cables and a protective earth if input or output cables are subjected to electro static high voltage discharges due to for example atmospheric events Please also be aware that if you connect mains to any relay contact you will have hazardous voltages inside the module Remember you are not allowed to open the module for any reason Any service must be performed by Arteco technicians only ETHERNET I O MODULE USERS MANUAL 3 INTEGRATED WEB SERVER The unit features an integrated Web Server that allows the user to fully operate the device It is possible to set network parameters O mnemonic names password protection dynamic dns operation It is also possible to read input channel status and set reset outputs I O can also be driven by CGI commands without using the web interface See the Ethernet I O module CGI Commands Interface manual for further reference Below you can see the main page of the module please note the hostname indicator in the red bar above the command list it can be useful to locate the module you are connected to should you have several modules to manage This information is repeated in every page dr teu tc motion control technologies Hostname ARTECONET Arteco Ethernet digital I O module Home I O setup Network setup I O monitor Restore factory settings Change password Ddns service Firmware upgrade
4. to 9 5 mm Gently push with a screwdriver the square peg of the connector lowering it for 2 mm insert the wire with 45 angle and release the peg Unit also features a standard RJ45 shielded connector for LAN connectivity 1 4 Power rating The unit must be powered from a SELV source rating 24 10 500 mA The negative pole of the power supply unit must be earthed 1 5 Installing The unit is designed for din rail mounting It must be installed in a closed cabinet without dust and within the moist limits above listed see 1 2 Environment The device is a building in equipment as per EN 60950 1 2 3 6 ETHERNET I O MODULE USERS MANUAL 2 CONNECTIONS 2 1 Connector names and functions Use PIC1 as reference for connections to the Ethernet I O module i E O Supply P1 Serial Port P2 P3 In0 int In2 In3 In4 Ins In6 In7 Wee Vee Gad Gad ERE arteco Input Status ETHERNET REMOTE 10 P6 Relay Digital Out P7 Relay Digital Out EthernetPS no0 c1 nol 2 no2 no3 ch no4 c5 nos c no C nme Expansion PS i o lt PIC 1 Starting from top left P1 power supply connect a SELV source rating 24V 10 0500 mA each connection has two contacts internally connected P2 serial port optional not implemented Do not connect P3 input conn input connections Each input draws about 8 mA 024 V inputs are provided with a green color status led P4 GND In return of the input conne
5. Copyright 2012 Arteco Motion Tech ETHERNET I O MODULE USERS MANUAL Next option from top of the list is I O setup However leaving the main page for any other one requires the user to enter username and password Default username is admin and default password is arteco Enter them in the correct fields and click ok to proceed eee M M p dr Teco Te roeor motion control technologies Hostname ARTECONET PI thernet digital 1 0 module I O setup Il server 192 168 10 96 all indirizzo Protected richiede un nome utente e una password Network setup Avviso il server ha richiesto che il nome utente e la password siano inviati senza protezione ovvero mediante I O monitor autenticazione di base senza l uso di una connessione protetta Restore factory settings Mome utente gt Password Change password Memorizza password Ddns service Firmware upgrade Copyright 2012 Arteco Motion Tech ETHERNET I O MODULE USERS MANUAL The I O setup page now will show prg ar T Teco lt motion control technologies Input Output setup I O setup This page allows to join a user s choice label to each input output channel Network setup 1 OO i INPUTO this is a user choice field I O monitor i i INPUT1 input_1 s
6. E USERS MANUAL use the IP address of another device already on the network as an IP conflict will occur Gateway Subnet mask Primary DNS Secondary DNS enter here the correct values that apply to the network you are connected to If unsure please refer to your network administrator After entering the desired values in this page click Save Config to make them persistent If you changed the IP address you will loose connectivity to the board since the parameters are immediately changed You will need to redirect your browser to the new IP address you entered If you have lost connection to the board and can t recover from this you can have the module back alive to the factory settings operating on the rear dip switch See further in this manual for the recovery procedure Next option of the list is I O Monitor motion control technologies Hostname ARTECONET Arteco Ethernet digital I O module LN Input Output status I O setup This page allows to monitor inputs and set outputs Network setup 1 ee ee E A E E EE AA I A e n I O monitor i Inputs Restore factory PRA 3 P settings i this is a user choice field OFF i input_1 OFF Change password i linput_2 OFF Ddns service EE i input 4 OFF nput 5 OFF input_6 OFF input_7 Outputs output 0 ON output 1 ON output_2 OFF output 3 OFF output 4
7. ETHERNET I O MODULE USERS MANUAL pr pr fer nno dif Ce CoO etl T T motion control technologies ETHERNET I O MODULE Users Manual Rev 1 1 8 10 2012 ARTECO S r l Via Gentili 22 48018 FAENZA RA Tel 39 0546 645777 Fax 39 0546 645750 Email arteco arteco it Web www arteco cnc it ETHERNET I O MODULE USERS MANUAL Copyright O Arteco S p A 2012 Information contained herein is a property of Arteco Srl It is forbidden to copy and redistribute this manual either partially or entirely without written permission of Arteco srl All specs are subject to change without notice This manual is periodically revised and updated Even if any effort has been taken to make the information contained herein complete and reliable Arteco may not be considered responsible for any missing or wrong information that this manual might contain Any suggestions about this manual will be however taken into account for its future releases Hevisions 2 09 2012 preliminary 8 10 2012 preliminary safety instructions added page 7 output power rating revised page 6 dip switch settings corrected page 17 ETHERNET I O MODULE USERS MANUAL INDEX CHAPTER 1 General information 1 1 Carrying and handling Re ENVION S enses iasotoenz E eR TUNE TIR E E E EE UIN TRE 4 IS WO cR RITENUTO apice ei del 4 1 4 Power FEOQUIFCI
8. MCING x ITE i M LELE Fee AA E CHAPTER 2 Connections 2 1 Connections names and functions 5 eZ Ig m 7 CHAPTER 3 Integrated web server MSIgNerc e MEET um 8 HP OUUU SO U e Tm 10 NCI WOT GOUD eran E E dum NUT SIM VUE 11 12 ai tesreazs aet 13 FS SWOT CANO enne TTD TTE 15 Wi icuneP HEP 16 alie iaceo m 17 Module default 8 18 SAFETY INSTALLATION RULES iude IDEAE ee ADAM ER AERA OO Dn d M T ETHERNET I O MODULE USERS MANUAL 1 GENERAL INFORMATION 1 1 Handling Upon unpacking your Ethernet I O Module please be aware of any damaged container If so please refuse the delivery and contact your carrier Please use any precautionary measures against risk of damage due to electrostatic discharge 1 2 Environment Storage 10 to 55 C non condensing Operational 5 to 40 C non condensing Moisture 30 to 90 non condensing Altitude 2000 m max 1 3 I O Connections The unit is provided with spring loaded connectors for rapid insertion of AWG 20 to AWG16 wires 0 5 to 1 5 mm Cut off insulation from wire for about 8 5
9. ction of P3 connector Please note that these connections are NOT connected to the power GND of connector P1 since inputs are optically insulated ETHERNET I O MODULE USERS MANUAL Starting from bottom left P5 Ethernet standard shielded Ethernet connector Connect to a router hub or Ethernet switch Connector is provided with two status leds a yellow led for link and a green one that blinks on network activity P6 Relay Digital Out P7 Relay Digital Out P8 Serial expansion connect here the first four loads you want to control Each of the four outputs has two contacts named c x and no x which stand for common and normally open Output rating is 250V 1 5A resistive load Each output is provided with a green color led status indicator same as P6 for the second group of four loads proprietary expansion connector do not use DO NOT CONNECT ANY ETHERNET DEVICE HERE THIS IS NOT AN ETHERNET PORT ANY DEVICE CONNECTED TO THIS PORT CAN BE SERIOUSLY DAMAGED AND OR DAMAGE THE UNIT ETHERNET I O MODULE USERS MANUAL 2 2 WIRING SAFETY INSTALLATION RULES PLEASE READ CAREFULLY When connecting the unit care must be taken to absolutely observe the following 1 Wire size must be adequate for the purpose a 1mm minimum wire gauge must be used for power supply at connector P1 b 0 5 mm minimum wire gauge must be used for input connectors P3 and P4 c Depending upon application o
10. ettings i INPUT3 finput_3 Change password i INPUT4 input_4 INPUT7 input 7 OUTPUTO output 0 OUTPUTI output 1 OUTPUT2 output 2 OUTPUT3 output 3 OUTPUT4 output 4 OUTPUTS output 5 OUTPUT6 output 6 OUTPUT7 output 7 Save M M 1 Copyright 2012 Arteco Motion Tech srl As you can see this page allows a user to change the default names to user defined names for mnemonic purposes Simply enter the name in the field related to each channel and click save when you are done Names will be saved in the module flash memory and retrieved as needed Note do not use spaces when writing names use the underscore instead 10 ETHERNET I O MODULE USERS MANUAL Next option of the list is Network setup Teco o motion control technologies Hostname ARTECONET I O setup Network setup I O monitor Restore factory settings Change password Ddns service Firmware upgrade Arteco Ethernet digital 1 0 module Board Configuration This page allows the configuration of the board s network settings CAUTION Incorrect settings may cause the board to lose network connectivity Enter the new settings for the board below MAC Address 0004A355E21E i Host Name ARTECONET T Enable
11. l be set to factory defaults Network setu si Click NEXT to complete reset sequence IfO monitor Allow 15 sec for reboot Restore factory settings Module will restart at address 192 168 10 96 Change password Ddns service Firmware upgrade Copyright 2012 Arteco Motion Tech srl At this point you can still escape from Module Reset clicking on any of the options on the left If you however want to completely reset the module click NEXT tab and follow the instructions after 15 seconds close the browser window and reopen it at the address that was shown in the Module Reset page and the module will be back as shipped from factory Should this page be unavailable you have as earlier mentioned an hardware option to recover from scratch the module See further in this manual for the recovery procedure 14 ETHERNET I O MODULE USERS MANUAL Next option of the list is Password change px cr lt motion control technologies Hostname ARTECONET Arteco Ethernet digital I O module Password change I O setu 4 P Please enter new username and password in the fields below Network setup I O monitor username admin Restore factory password settings Change password Save Ddns service Firmware upgrade Copyright 2012 Arteco Motion Tech srl Use this page if you want to change the default username and or password It is strongly
12. ly after save the module will do an attempt to check with the site for an update of the module IP address itself at the operator s site The same will be done each time the module detects a change in its IP address due to the use of a dynamic IP address The response will be shown in the above window here we read that the current configuration is not valid since the entered fields are blank when correct values are entered they will be readable in their fields with the exception of the password field that will show dots and we can read status messages like the last update was successful or ip has not changed since last update or even an error occurred if anything in the update procedure went wrong 16 ETHERNET I O MODULE USERS MANUAL Hardware recovery If you can t connect anymore to the module due to wrong network parameters you entered there is a way of resetting all network settings to the default values As you can see there is a 8 way dip switch on the back of the unit Default setting for the switches is all OFF If you want to reset network settings please set dip1 to ON then cycle the power to the unit OFF and then ON Module will start up with default network settings Then you can set back dip1 to OFF position to recover normal operation The IP address to which the module will reset depends on the settings of the dip switches 5 and 6 In the details we have DIP5 OFF and DIP6 OFF addre
13. recommended not to leave the default username and password After change the new username and password will be immediately operational 15 ETHERNET I O MODULE USERS MANUAL Next option of the list is Ddns service me Um meas m r arteco motion control technologies Hostname ARTECONET Arteco Ethernet digital I O module LX Dynamic DNS I O setup The current configuration is not valid Network setup Dynamic DNS allows to update the module s global IP address to various Dynamic DNS services This feature along with proper port forwarding in place at the router can enable global access to a device behind a NAT router or firewall I O monitor Restore factory settings Enter the settings in the fields below Change password Ddns service DDNS Service DynDNS www dyndns com UserName Firmware upgrade Password Host Set DDNS Configuration Copyright 2012 Arteco Motion Tech srl This page allows to enter the settings for a Dynamic dns service from various operators This allows the user to operate the module from the internet even if it is behind a router that uses dynamic IP This firmware release however only implements service from dyndns org User must first register at www dyndns org entering his her name password and the domain name among the available ones The domain name will become the module name The same parameters must be entered in this page and saved Immediate
14. ss is 192 168 10 96 DIP5 ON and DIP6 OFF address is 192 168 1 96 DIP5 OFF and DIP6 ON address is 169 254 0 2 17 ETHERNET I O MODULE USERS MANUAL DIP5 ON and DIP6 ON address is 10 0 0 2 The default factory setting is DIP5 OFF and DIP6 OFF gt 192 168 10 96 The choice for different IP address classes is to ease first module startup allowing the module to be visible in different local networks The other dip switches have these functions Dip switch 2 if ON at power on resets all of the I O names you eventually changed to their default values No other settings are affected by this Dip switch 3 if ON at power on the module s username and password will be reset to the default ones user is admin and password is arteco The other dip switches are unused or reserved please let them in OFF position DEFAULT MODULE SETTINGS IP ADDRESS 192 168 10 96 USERNAME admin PASSWORD arteco
15. ther requirements may apply Installer is required to follow all applicable rules that may apply in his her country 2 Output connector wiring P6 and P7 Please use 1 mm minimum wire gauge to connect loads to these connectors It is mandatory to protect the relay output contacts with an external quick acting fuse rated 250V 1 5A max Please note that for safety reasons if you use a contact say on connector P6 to switch mains supply you are not allowed to use the other contacts of the same connector to switch SELV circuits i e circuits that users can come in contact with It is also mandatory to have an external disconnecting device for each of the connections from mains to the relay output contacts conn P6 and P7 So for example if you switch a 220 V light bulb with P6 c0 no0 contacts you can t use c1 no1 c2 no2 and c3 no3 to switch say a 12 V supply to a low voltage device You can however use these remaining contacts to switch other mains connected devices or to drive additional mains powered external relays You can use the other four outputs connector in this case P7 to drive low voltage circuits If you connect long wires to relay contacts either at low voltages or mains please take care of wire inductance that may cause an arc through relays contact at opening thus shortening their life Consider using capacitors or arc snubber components in parallel with relays contacts TVS transient voltage suppressor
Download Pdf Manuals
Related Search