Digipass 270. User Manual 175.82 KB
Contents
1. BANKING INVESTMENTS ADVISORY DigiPass 270 User manual Your digipass DigiPass 270 Display Input buttons se To start or finish using the device press the ji button and holding it press the D ttON Unique device identifier 18 13555565 8 k doima Note After the PIN code is entered correctly the following message will be displayed prompting to enter the new PIN code NEW PIN Enter the new PIN code 2 You will need to re enter the new PIN code After the new PIN code is successfully re entered the following message will be displayed NEW PIN CONF Memorize the new PIN code to be further used General Information Digipass is a device used for customer identification and for signing documents when working with the bank remotely It is an electronic device that generates a unique test key combination of digits which is used instead of signature and seal for signing documents to be sent to the bank For calculating test keys main parameters of a document or a set of documents are used as well as the calculation time The advantage of digipass compared to other remote access tools is the high security and confidentiality level of your personal data ensured when working with the bank A digipass issued by ABLV Bank Luxembourg S A may be used for working with ABLV Bank Luxembourg S A only Digipass may only be used after changing initial PIN code2. which consists of 4 digits Turning the device on for the first time you will be prompted to enter the initial PIN code provided by the bank Security Issues Do not store your device PIN code together with the device itself If you have suspicions that your device might have been accessed by third parties change the PIN code To change the PIN code press the pa button and hold it until the following message is displayed NEW PIN f your digipass is lost immediately inform the bank about it calling the Client Line at 371 6777 5555 or contact your Private Banker Digipass warranty period is 4 5 years f you have suspicions about your device working Incorrectly display is blinking digits are not clear etc inform the bank of it Note When using Internetbank all parameters necessary for calculating a test key will be provided to you during sending the document to the bank including the cases where you need to send several orders for different amounts and to different beneficiaries at once When generating test key for signing documents sent to the bank by fax the first value sender s customer code should consist of seven digits e g 0012345 Signing documents using digipass For signing documents you need to use SIGNATURE program which generates an electronic signature a test key for confirming financial documents transfer orders applications etc Such signatur
3. number should be dropped out 2 in case the obtained value is not longer than 10 digits the whole value should be entered for calculating a test key 2 in case the obtained value is longer than 10 digits the last 10 digits on the right should be entered for calculating a test key Notel To unblock the device completely you should proceed as follovvs 1 Call Client Line at 371 6777 5555 and provide the device identifier and the CHALLENGE value described above to the operator 2 The operator will provide a RESPONSE code consisting of eight digits which you should enter in your d gipass device For example the beneficiary s account number is LV 12 AIZK 1234 5678 9012 3 gt il 17120 107 9012 5 221507290123 1217 Z 2202 the parameter will be 4567890123 If there is no beneficiary s account field in the document that is being signed the value 0 should be entered for calculating a test key After completing the above procedure you will obtain a test key for signing financial documents When using Internetbank all parameters required for calculating test key will be provided to you immediately when sending the document to the bank The same applies to sending several orders at once for transters of different amounts to be made to different beneficiaries Unblocking of Digipass If you enter incorrect PIN code the following message will be displayed PIN FAIL 1 where the
4. digit stands for the number of incorrect PIN code entries To enter the PIN code once again press the PM button and holding it press the pa button After five successive entries of incorrect PIN code the digipass device will be automatically blocked and the following message will be displayed LOCK PIN FAIL 5 When turning the device on later the message LOCK PIN 12345678 will be displayed the digits representing the CHALLENGE code In case the device was turned off when turning It on the CHALLENGE code will be displayed Press the pa button to switch to entering the RESPONSE code After you have correctly entered the RESPONSE code provided by the operator the prompt for entering new PIN code will be displayed NEW PIN Enter the new PIN code You will be prompted to re enter the new PIN code After the new PIN code is successfully re entered the following message will be displayed NEW PIN CONF
5. e may be used both for working in the Internetbank and for submitting documents to the bank by fax For generating an electronic signature the following signature parameters should be used the customer code of the customer which appears to be the signatory of the composed document the transfer amount and the beneficiary account To select the SIGNATURE program after the device is activated and the following message is displayed APPLY press button 3 You will be prompted for entering value of the first parameter customer code of the sender Enter your customer code one to seven digits To confirm it press and hold for 2 3 seconds the button until a prompt for entering next parameter is displayed Then enter the transter amount In the document being signed the amount may consist of 1 to 12 digits To calculate the code only integral part of the amount value should be used not using the decimal places kopecks cents centimes etc For example the amount is 25 000 00 gt the parameter will be 25 000 the amount is 15 50 gt the parameter will be 157 If there is no amount field in the document that is being signed the value 0 should be entered for calculating a test key The last parameter for calculating a test key is the beneficiary s account number t can be 1 to 10 digits long The parameter value should be obtained as follows 1 all symbols other than digits in the account
Download Pdf Manuals
Related Search