Owner`s Manual - Spectrum Industries, Inc.
Contents
1. Warranty Table effective 1 1 2015 Adjustable Crank Electric Desk Legs e 1 Year Flat Panel Desk Gas Cylinders Chairs Adjustable Height Chair Parts including frames gas 7 Years cylinders wood and plastic parts control handles casters Adjustable Height Chair Upholstery 2 Years In Stock Upholstery 2 Years Graded In Fabrics and Customer Owned Material No Warranty Height Adjustable Columns and Lifts 1 Year General Use Casters Electrical including timers and LINAK actuators Keyboard Mouse Trays Flat Panel Monitor Arms e Flat Panel Monitor Arm General Parts e 5 Years e Flat Panel Monitor Arm Gas Cylinders e 2 Years Desks and Lecterns e Computer Desk Chassis e Cart Chassis 10 Years e Lectern Chassis 925 FIRST AVENUE CHIPPEWA FALLS WI 54729 800 235 1262 715 723 6750 WWW SPECTRUMFURNITURE COM 0118629 Page 13 of 132. 1 Carefully roll the table upright this will take 3 4 people Figure 5 SPEC LARUM INDUSTRIES ING 0118629 Page 6 of 13 6 Display Stand Optional Display Stand If you have the optional display stand proceed with the installation at this time Figure 6 Instructions included with stand Cord management options Cords and wiring from any worksurface devices can be routed cleanly throughout the unit using grommet holes and openings in the bottom of the technology compartment Technology compartment Side panel stop adjustment 4mm Hex wrench Required If necessary the offset panel stops can be adjusted to slightly shift the closed position of the panels and lock rods 1 Loosen the JC bolt slightly with a 4mm hex wrench Figure 7 2 Rotate the stop until the panel is positioned correctly Be sure the lock rods engage easily 3 Re tighten the JC bolt securely SPEC ERAM INDUSTRIES ING 0118629 Page 7 of 13 eLift operating instructions eLift equipped tables only Phillips screwdriver O D 5 O D X 1 Attach the control button bracket under the radiused portion of the worksurface with 2 8 x 5 8 PHSM screws and pre drilled pilot holes in the center of the worksurface 2 Push the control button onto the bracket 3 Use the included pine tree clips to secure the cord to the worksurface Control button Curved or
3. rectangular end worksurface Pine tree clip Up Down Control 8 x 5 8 PHSM button screws Pine tree clip Cord Note Additional sets of pre drilled mounting holes are available under the straight sections of the worksurface to mount the control button if preferred Operation Plug the 11 foot 15 amp power cord into a wall outlet Locate the Up and Down buttons on the control pad To raise or lower the worksurface press and hold the up or down arrow keys on the control pad until the worksurface reaches the desired height The worksurface maximum height is 42 minimum height is 29 Keep clear of pinch points during worksurface movement Keep clear of pinch points during worksurface movement Reset Procedure Note The lift actuators are rated at a maximum capacity of 180 Ib each Unplug then re plug the power cord into a wall outlet Make sure all lift mechanism wire connections are in place and secure Remove anything located under the worksurface Press and hold the Down button to lower the worksurface to the Always unplug the eLift before working under the worksurface ONES UVES TORSTEN QUAI eee TONAL Although this table utilizes an anti collision feature that briefly stops Release the Down button and reverses the motion of the table in the event of an obstruction Use caution when raising or lowering the worksurface Do not sit at under or on the wo
4. a DESKLINE system developed for desks and for indoor use in offices Do not use it in industrial kitchens or in other enviroments that have to be cleaned with aggressive detergents Do not bolt the legs to the floor so that free movement is prevented This could cause serious damage to the legs in fault situations Warranty There is a 36 months warranty on the DESKLINE products against manufacturing faults from the production date of the individual products see label LINAK A S warranty is only valid in so far as the equipment has been used and main tained correctly and has not been tampered with Furthermore the system must not be exposed to violent treatment In the event of this the warranty will be ineffective invalid For further details please see LINAK A S ordinary conditions of sale Maintenance Clean dust and dirt on the outside of the system at appropriate intervals and inspect them for damage and breaks Inspect the connections cables and plugs and check for correct functioning as well as fixing points Service of double insulated products Class Il A Class Il or double insulated electrical appliance is one which has been designed in such a way that it does not require a safety connection to electrical earth US ground The basic requirement is that no single failure can result in dangerous voltage becoming exposed so that it might cause an electric shock and that this is achieved without relying on an earthed
5. in an environment that corresponds to their IP protection Misc The actuator system has a sound level below 55dB A in typical applications Updated manuals and declarations can always be found here www linak com deskline DL6 LINAK G WE IMPROVE YOUR LIFE item No DL6000A00650560 Prod Date 2006 05 09 Max Load 800N mae Rate 18 V 10 Amp Cych Mh Men 2 min n 18 min SONNEL Z iu in WCE 23456 0 MADE BY LINAK A S DENMARK A Only for EU markets e This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved e Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision A Only for Non EU markets e Persons who do not have the necessary experience or knowledge of the product products must not use the product products Besides persons with reduced physical sensory or mental abilities must not use the product products unless they are under surveillance or they have been thoroughly instructed in the use of the apparatus by a person who is responsible for the safety of these persons e Moreover children must be under surveillance to ensure that they do not play with the product e Itis the operator s responsi
6. not authorized by Spectrum or any other cause outside the control of Spectrum Spectrum will at its sole option either repair or replace the defective product This warranty is exclusive no other warranty written or oral is expressed or implied This warranty is given by Spectrum to Buyer and to no other per son or legal entity No Spectrum dealer distributor agent or employee is authorized to make any modification or addition to this warranty NOTWITHSTANDING ANYTHING TO THE CONTRARY SPECTRUM WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE FOR INDIRECT OR LIQUI DATED DAMAGES INCLUDING CONSEQUENTIAL INCIDENTAL AND SPECIAL DAMAGES IN NO EVENT SHALL SPECTRUWM S LIABILITY WHETHER UNDER CONTRACT OR WARRANTY IN TORT OR OTHERWISE EXCEED THE PURCHASE PRICE RECEIVED BY SPECTRUM FOR THE PRODUCT AT ISSUE AND RECALL ACTION EXPENSES SPECTRUM SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES WHETHER ARIS ING OUT OF BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE AND STRICT LIABILITY OR OTHER THEORIES OF LAW WITH RESPECT TO PRODUCTS SOLD OR SERVICES RENDERED BY SPECTRUM OR ANY UNDERTAKINGS ACTS OR OMISSIONS RELATING THERETO Our Customer Service Department is ready to provide immediate attention to any questions comments or concerns They are available to answer your calls Monday through Friday from 7 am to 5 pm CST In addition your product comments or concerns are welcome via e mail at soectrtum spectrumfurniture com
7. Power Module 99044 e Two power receptacles per module Two USB charge ports not data compatible Thumbscrew clamps Requires worksurface cutout ETL listed Available in Black or Silver Cutout required Power cord Power receptacles USB charging ports Dimensions Unit weight 5 25 W 13 3 cm x 2 D 5 1 cm 5 vertical positions in 2 increments Mounting holes and cutouts needed on flat end of worksurface mounts to surface thicknesses up to 1 5 9 274 cm with 90 flat plug with 45 rotation 12A 120 VAC spill resistant 2 1A 10 5W 6 W 15 2 cm x 2 5 D 6 35 cm x 3 18 H 8 1 cm 2 29 Ib 1 kg Pe lt lt Display von x Worksurface option with mounting holes required specify when ordering LISTED Intertek SPEC AALL INDUSTRIES INC 0118629 Page 9 of 13 Electric leg information A Warning Failure to comply with these instructions may result in accidents involving serious personal injury Failing to follow these instructions can result in the product being damaged or being destroyed A Safety Information General Safe use of the system is possible only when the operating instructions are read completely and the instructions contained are strictly observed Failure to comply with instructions marked with the NOTE symbol may result in serious damage to the system or one of its components e Itis important for every
8. SPEC Hitt IAN Owner s Manual INDUSTRIES INC InVision Access Nano Table Shown with optional display stand A Important A Before using this product e Read this manual e Comply with all safety and operating instructions e Ensure all parts and correct quantities are included Any parts damaged during shipment must be reported within 15 days of receipt To report information regard ing missing parts or damage to purchase parts or accessories or if you have any questions please contact us Thank you for purchasing Spectrum products Spectrum Industries Inc 925 First Avenue Chippewa Falls WI 54729 USA 800 235 1262 715 723 6750 www spectrumfurniture com 0118629 Page 1 of 13 Important Safety and Care Instructions Read this owner s manual before assembly or operation Do not allow children to move the table For indoor use only Do not install or store the table where it will be exposed to moisture Do not block the ventilation openings Do not allow anyone to sit stand or climb on the table Use a damp soft cloth or sponge with mild soap or detergent solution to clean dirty surfaces Do not use harsh solvents or abrasives This table is intended for institutional use It does not have any user serviceable parts or user maintenance requirements If servicing is necessary please contact Spectrum Industries for assistance Awami g Relocating audio and or video equipment to furniture not speci
9. bility to ensure that there is free space for the application to move without risk for the operator or bystanders before operating the application Misuse Do not overload the actuators this can cause danger of personal injury and damage to the system e Do not use the actuator system for lifting persons Do not sit or stand on a table while operating risk of personal injury Do not use the system in environments other than the intended indoor use Repairs In order to avoid the risk of malfunction all DESKLINE repairs must only be carried out by authorised LINAK workshops or repairers as special tools must be used and special gaskets must be fitted Lifting units under warranty must also be returned to authorised LINAK workshops Warning If any of the DESKLINE products are opened there will be a risk of subsequent malfunction Warning The DESKLINE systems do not withstand cutting oil CBD4 LINAK G WE IMPROVE YOUR LIFE Sundby DESIGNED IN DENMARK Power Item CBD4H00040A 409 Date 130521 Ulin 120V 60 Hz Pin 600W U Out 12 24 V Op 10 Max 2 min 18 min S W P N 0077474 Ver 1 12 AE SOAGCEY DUME INSULATED WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS NOT TO BE OPENED BY UNAUTHORIZED PERSONNEL P O 110125 ASSEMBLED IN CHINA 01 i File E151104 SPEC AALL INDUSTRIES INC 0118629 Page 10 of 13 Misc on the DESKLINE DL5 DL6 system This system is
10. e plug the power cord into a wall outlet Make sure all lift mechanism wire connections are in place and secure Remove anything located under the worksurface Press and hold the Down button to lower the worksurface to the lowest work position until it stops moving Release the Down button Press and hold the Down button again and hold for 30 seconds The worksurface will then lower slowly to the RESET MODE position slightly rise and stop moving The worksurface must be completely lowered before resuming operation Note If the worksurface does not lower when doing this step release the Down button and retry step 6 Release the Down button The lift mechanism has now been reset and the worksurface can be adjusted normally SPEC LARUM INDUSTRIES ING 0118629 Page 12 of 13 WE WILL MAKE IT RIGHT FOR YOU Spectrum is committed to provide complete customer satisfaction Each of our products is manufactured from the best materials available and each product is stringently monitored throughout the production process through our P A C E program Product Assurance to meet Customer Expectations We expressly warrant that Spectrum products will be of good quality and workmanship and free from defect for the period set out in the warranty table below from the date of delivery This warranty shall not apply to defects or damage resulting from misuse abuse neglect improper care modification or repair
11. e standard CBD4 CBD5 CBD6 advanced control box software 0077432 version 1 66 and later A system with anti collision can limit material damages on a desk if a collision with a solid object should occur DL5 DL6 Enabling the anti collision To enable the anti collision function a little plug called a dongle must be mounted in one of the 2 control ports The function is only active when the dongle is mounted If you remove the dongle again you disable the function Method of operation When the DL DB s are running the CBD4 CBD5 CBD6 monitors the current consumption on each channel using a special algorithm If the current consumption on one channel is increased more than a predefined slope a collision is assumed and all channels are stopped immediately and all DL DB s will start to run in the opposite direction approx 50 mm This return drive is done automatically and continues with or without any control key pressed for max 2 5 sec The anti collision sensitivity is different in upward and downward direction Upwards the force is approx 20 kg Downwards the load will be approx 40 kg the load on the DL DB the desk what is on top of the desk The 40 kg are needed to activate the anti collision function Situations where the anti collision does not work There are situations where the anti collision will not be activated These situations are e If the collision happens during the initialisation phase e f the c
12. fically designed to support audio and or video equipment may result in death or serious injury due to the furnishing collapsing or over turning onto a child A Waming Death or serious injury may occur when children climb on audio and or video equipment furniture A remote control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over on to the child Electrical Safety Keep the power switch in the OFF position before plugging or unplugging from the wall outlet Ensure total device equipment load does not exceed 12 amps Do not plug the power cord into an extension cord Inspect the power cords for damage before each use Do not use power cords that are damaged Unplug power cord from electrical outlet by gripping the cord Do not unplug the power cord by pulling only on the cord Do not step on drive over drag or place objects on the power cord For added safety plug the cart into a grounded outlet controlled by a GFI Ground Fault Interrupter circuit breaker Damaged electrical components can create significant hazards to users and is not covered by the warranty Repairs should always be performed by a qualified electrician Electrical devices are not toys Children are often unaware of the hazards associated with electrical devices This table must always be used by adults or with adult supervision SPEC LARUM INDUSTRIES INC 0118629 Page 2
13. metal casing This is usually achieved at least in part by having two layers of insulating material surrounding live parts or by using reinforced insulation There is no earthing grounding means provided on the product and no earthing ground ing means is to be added to the product double insulated or In Europe a double insulated appliance must be labelled Class II bear the double insulation symbol a square inside another square Servicing a double insulated product requires extreme care and knowledge of the system and is to be done only by qualified service personnel Replacement parts for a double in sulated product must be identical to the parts they replace f The cleaners and disinfectants must not be highly alkaline or We acidic pH value 6 8 Description of the DESKLINE DL5 DL6 system Each DESKLINE DL5 DL6 lifting units is equipped with a motor and parallel memory drive is ensured by means of software in the CBD4 CBD5 CBD6 that also takes account of oblique load on the desk Soft start and stop are also part of this software which ensures a soft start and stop when adjusting the desk Application of the DESKLINE DL5 DL6 system Irrespective of the load the duty cycle 10 6 min hour or max 2 min at continuous use stated in the data sheets must NOT be exceeded as this will result in a superheating of the motor the brake and the spindle nut Exceeding the duty cycle will result in a dramatic reduc
14. of 13 1 0116814 1 0116818 Table core with set and go legs Table core with eLift legs shipping position shown shipping position shown Hardware 1 0109398 2 037542 Control button 8 x 5 8 bracket PHSM 1 0109397 2 0107023 Control button Snap in pine tree clip 2 037779 5 16 18 Glide 1 Worksurface Hardware ss si 8 021551 2 0101382 DP 2 026064 1 025069 a 1 4 20 x 5 8 PHMS Glide wrench lt lt 4 037779 5 16 18 Glide 1 4 20 x 2 3 4 14 x 7 8 PHSM 7 PHMS SPECTRE INDUSTRIES ING 0118629 Page 3 of 13 Assembly Setup 1 Unpack amp detach from pallet 1 2 3 Phillips screwdriver Remove outer sleeve Figure 1A r Unscrew the 4 Phillips head wood screws securing the table core to the pallet Figure 1B Without using a utility knife open the rest of the boxes Cordless drill with long magnetic best Phillips driver Tools Required Table core set and go legs shown 2 i a Glide wrench 2 Install glides 1 With the table core still upside down install the glides onto the legs included 4 on Set and go legs 6 on eLift legs Figure 2 Glide SPEC AALL INDUSTRIES ING 0118629 Page 4 of 13 3 Adjust leg height Set and go legs only Note If you have a table with eLift legs proceed to step 4 Tools Required Tables with adjustable height set and go legs can be adjusted to ha
15. ollision happens within the first 1000 msec or after the control button has been released e If the collision happens between the floor and the table and the load on the desk the weight of the legs are lower than 40 kg e Ifthe collision happens over too long time e g if the collision is with a soft object SPEC TRUM INDUSTRIES INC 0118629 Page 11 of 13 eLift Leg Troubleshooting Guide Be sure unit is plugged into a live circuit Loose electrical connections Make sure all electrical connections are securely plugged into the control box 1 Raise the worksurface by pressing the Up button 2 Remove any items sitting below the worksurface 3 Reset the lift mechanism see below for procedure Object encountered under worksurface Reset Procedure This table has a load sensing anti collision feature in the controller that actively locks out the lift mechanism when unbalanced loads are encountered i e weight from a person sitting on one side of the table The following reset procedure should be performed if the lift mechanism becomes locked out and the table does not extend or retract A WARNING Q eLift legs will not operate The anti collision feature does not function in RESET MODE Do not sit at under or on the worksurface while resetting the lift mechanism Be sure the table movement does not interfere with objects or people Do not place any items under the worksurface Misaligned actuators Unplug then r
16. one who is to connect install or use the systems to have the necessary information and access to the Owners Manual Follow the instructions for mounting risk of injury if these instructions are not followed e The appliance is not intended for use by young children or infirm persons without supervision lf there is visible damage on the product it must not be installed e Note that during construction of applications in which the actuator is to be fitted there must be no possibility of personal injury for example the squeezing of fingers or arms T i Assure free space for movement of application in both directions to avoid blockade Before installation re installation or troubleshooting Stop the DL5 DL6 e Pull out the mains plug e Relieve the DL5 DL6 of any loads which may be released during the work Before start up e Make sure that the system has been installed as instructed in this User Manual e Make sure that the voltage of the control box is correct before the system is connected to the mains System connection The individual parts must be connected before the control box is connected to the mains See the User Manual for LINAK actuators if necessary During operation Ifthe control box makes unusual noise or smells switch off the mains voltage immediately e Take care that the cables are not damaged Unplug the mains cable on mobile equipment before it is moved e The products must only be used
17. rksurface when operating the lift mechanism and be sure table movement does not interfere with objects or people Press and hold the Down button again and hold for 30 seconds The worksurface will then lower slowly to the RESET MODE position slightly rise and stop moving The worksurface must be completely lowered before resuming operation Note If the worksurface does not lower when doing this step release the Down button and retry step 6 A CAUTION A Release the Down button The lift mechanism has now been reset and the worksurface can be adjusted normally USE CAUTION WHEN RAISING OR LOWERING TABLE SPEC LUM INDUSTRIES ING 0118629 Page 8 of 13 Element Display Stand 37130 e Bolts directly to worksurface e Integrated cable management routes and hides wires e Adjustable VESA compatible mount e Requires worksurface mounting holes and cutout Monitor size range Weight capacity Vertical adjustment worksurface to center Tilting Shipping weight 7 501 19 05 cm Accessories Available separately after initial configured purchased 32 55 81 3 cm 139 7 cm diagonal 100 Ib 45 4 kg e 23 5 H 59 7 cm e 21 5 H 54 6 cm 19 5 H 49 5 cm e 17 5 H 44 5 cm e 15 5 H 39 4 cm 15 range 35 Ib 15 9 kg i 1 234 0 312 3 14 cm 0 8 c 4 x a 2 O 7 86 cm 3 532 4 75 8 97 cm 12 06 cm Cove
18. tion of the life of the system The DESKLINE DL5 DL6 system range contains the following products e 1 control box CBD4 CBD5 CBD6 e 1 single DL5 DL6 or 2 3 or 4 parallel e 1 exchangeable mains cable e 1 2 3 or 4 motor cables e 1DP1U DPF1M if memory function is required DP1C WDPL DPT DPF1C if memory function and display is required or 1 DPA DPB DP1K DP1V DPF1K if only up down is required Electrical connection of the DL5 DL6 system The DESKLINE DL5 DL6 system is to be connected as shown on figure 4 Each DL5 DL6 is to be connected to the sockets on the control box by means of the motor cables which have an 6 pin plug in each end Finally the mains cable is to be mounted and power switched on ng Please note that the control box must only be connected to the voltage stated on the label CBD4 CBD5 CBD6 with earth The CBD4 CBD5 CBD6 earth cable to be mounted on the desk construction typically the top frame in a way that ensures good electrical contact The function of the earth cable is to earth the desk and ground static electricity The earth connection does not protect other electrical products A CBD4 CBD5 with mains cut off non ZERO models If the power cable is damaged it has to be replaced by an authorized LINAK service centre to avoid any danger DL5 DL6 cable hook for cable relief Ha cable Ze RAR DP WDPL DL5 DL6 N Anti Collision The function anti collision is an option for th
19. ve a worksurface height between 29 42 in 1 or 2 increments Figure 3A The factory set height is 29 H Adjustment to the leg height should be done while the table is still upside down on the pallet To adjust leg height 1 Remove both side panels to provide access Figure 3B Locate and remove the 4 1 4 20 x 5 8 PHM screws that secure the Set and go leg While these screws are removed have a helper support the detached leg 3 Locate the height indicator window and slide the leg to the desired height setting 4 Replace the 4 1 4 20 x 5 8 PHM screws and tighten securely 5 Repeat on the second leg using the same height setting 1 4 20 x 5 8 PHMS 4 required _ pr _ a a mT _ _ Set and go leg Phillips screwdriver or Cordless drill with long magnetic best Phillips driver Height indicator window SPECTRUM INDUSTRIES INC 0118629 Page 5 of 13 4 Install worksurface 1 Place the worksurface face down laminate side down onto a flat non abrasive surface Figure 4 2 Using 3 4 people carefully set the table core onto the worksurface and align the mounting holes this will take 2 4 people 3 Attach the worksurface using 8 1 4 20 x 2 3 4 PHM screws Phillips screwdriver Required Table core 1 4 20 x 2 3 4 PHMS 8 required 5 Flip Table upright
Download Pdf Manuals
Related Search