Manual - La Crosse Technology
Contents
1. 61 a Minimum Icon 2 Press the MIN MAX key once more to view the maximum indoor temperature and maximum outdoor temperature TIME i J5 INDOOR miete i OUTDOOR 2 s030 Maximum icon RESETTING THE MINIMUM AND MAXIMUM READINGS User may reset the minimum and maximum temperature data to the current value by the following steps t Press the MIN MAX key once to display the minimum data 2 Press and hold the MIN MAX key for about 3 seconds to reset all the minimum maximum data to the current values in a single action 3 Data of all outdoor and indoor sensor will be reset at the same time 64 TEMPERATURE TRANSMITTER The outdoor temperature is measured and transmitted to the Temperature Station every 16 seconds approximately The range of the Temperature Transmitter may be affected by the temperature At cold temperatures the transmitting distance may be decreased Please bear this in mind when placing the transmitter 65 915 MHz RECEPTION CHECK The Temperature Station should receive the outdoor temperature data within a few minutes after setup If the temperature data are not received about 2 minutes after setup the signal reception icon does not appear please check the following points 1 The distance of the Temperature Station or transmitter should be at least 1 5 to 2 meters away from any interfering sources such as computer monitors or TV set2. User shall remove all the batteries from the temperature station and transmitters and wait 60 seconds if setting has been done with one transmitter before 45 Insert the batteries to the first transmitter Within 2 minutes of powering up the first transmitter insert the batteries to the Temperature Station Once the batteries are in place all segments of the LCD will light up briefly Following the indoor temperature and the time as 0 00 will be displayed If they are not shown in LCD after 60 seconds remove the batteries and wait for at least 60 seconds before reinserting them The outdoor temperature from the first transmitter channel 1 should then be displayed on the Temperature station Also the signal reception icon will be displayed If this does not happen after 2 minutes the batteries will need to be removed from both units 46 and reset from step 1 Insert the batteries to the second transmitter as soon as the outdoor temperature readings from the first transmitter are displayed on the temperature station Note User shall insert the batteries into the second transmitter within 45 seconds of reception of the first transmitter 6 The outdoor temperature from the second transmitter and the channel 2 icon should then be displayed on the Temperature station If this does not happen after 2 minute the batteries will need to be removed from all the units and reset from step 1 47 7 Insert the batteries to the
3. 3 46 36 6 x 13 5 x 87 9 mm WARRANTY INFORMATION La Crosse Technology Ltd provides a 1 year limited warranty on this product against manufacturing defects in materials and workmanship 71 This limited warranty begins on the original date of purchase is valid only on products purchased and used in North America and only to the original purchaser of this product To receive warranty service the purchaser must contact La Crosse Technology Ltd for problem determination and service procedures Warranty service can only be performed by a La Crosse Technology Ltd authorized service center The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology Ltd or La Crosse Technology Ltd s authorized service center La Crosse Technology Ltd will repair or replace this product at our option and at no charge as stipulated herein with new or reconditioned parts or products if found to be defective during the limited warranty period specified above All 78 replaced parts and products become the property of La Crosse Technology Ltd and must be returned to La Crosse Technology Ltd Replacement parts and products assume the remaining original warranty or ninety 90 days whichever is longer La Crosse Technology Ltd will pay all expenses for labor and materials for all repairs covered by this warranty If necessary repairs are not covered by this warranty or if a product is examined which is no
4. 7 leaving the head extended out by about 5mm g A 69 Hang the Temperature Station onto the screw Remember to ensure that it locks into place before releasing i POSITIONING THE REMOTE es nf TEMPERATURE SENSOR 288 The remote temperature sensor can be placed onto any flat surface or wall mounted using the 70 bracket which doubles as a stand or wall mount base To wall mount j I Yj 1 Secure the bracket onto a desired wall using the Yj i Y screws and plastic anchors J 7 71 2 Clip the remote temperature sensor onto the bracket Note The mounting surface can affect the transmission range If for instance the unit is attached to a piece of metal it may then either reduce or increase the transmitting range For this reason we recommend not to place the unit on any metal surfaces or in any position where a large 72 metal or highly polished surface is in the immediate vicinity garage doors double glazing etc Before securing in place please ensure that the Temperature Station can receive the 915MHz signal from the temperature transmitter at the positions that you wish to place them CARE AND MAINTENANCE v Extreme temperatures vibrations and shocks should be avoided as these may cause damage to the unit and give inaccurate forecasts and readings 73 When cleaning the display and casings use a soft damp cloth only Do not use solvents or scouring agents as they may mark the LCD a
5. Contents Language Page English 1 French 35 Spanish 71 38 WIRELESS 915 MHz TEMPERATURE STATION Instruction Manual INTRODUCTION Congratulations on purchasing this compact 915MHz Temperature Station which displays time indoor temperature and outdoor temperature readings With two easy to use keys this product is ideal for use in the home or office 39 This product offers MT so 1 INSTANT TRANSMISSION INSTANT TRANSMISSION is the state of the art new wireless transmission technology exclusively designed and developed by LA CROSSE TECHNOLOGY INSTANT TRANSMISSION offers you an immediate update every 16 seconds of all your outdoor data measured from the transmitters follow your climatic variations in real time FEATURES LCD Display Hanging Hole gel Battery compartment cover Removable stand The Temperature Station Quartz clock with 12 or 24 hour time display hour and minute manually set Indoor and outdoor temperature reading in Fahrenheit F or Celsius C Can receive up to three outdoor transmitters Wireless transmission at 915 MHz Signal reception intervals at 16 seconds Minimum and Maximum records of indoor and outdoor temperature Low battery indicator Wall mounting or table standing removable table stand included 42 The Outdoor Temperature Transmitter Remote transmission of out
6. URE Display of outdoor temperature 58 MANUAL SETTING 12 24 HOUR TIME DISPLAY SETTING AND TEMPERATURE UNIT C F SETTING User may choose to display the time in 12 hour or 24 hour mode Note When the time display is set as 12 hour mode the temperature unit will be set to F when the time mode is in 24 hour format the temperature unit will be set to C 59 1 In normal display mode press and hold the SET CH key for about 3 seconds The 12h or 24h digit will be flashing 2 Press the MIN MAX key to set the desired time display mode 3 Press shortly the SET CH key to advance to the MANUAL TIME SETTING MANUAL TIME SETTING User shall manually set the time of the Temperature Station by the following steps 1 The hour digit of the time display will be flashing 60 2 Press the MIN MAX key to adjust the hour press and hold to allow fast advance Press SET CH key to confirm and go to the minute setting 3 The minute digit will be flashing Press the MIN MAX key to adjust the minute press and hold to allow fast advance Press SET CH key once more to return to normal display VIEWING THE MINIMUM AND MAXIMUM READINGS User may consult the minimum and maximum recordings for indoor temperature and outdoor temperature by following these steps 1 Press the MIN MAX key once to view the minimum indoor temperature and minimum outdoor temperature
7. door temperature to Temperature Station by 915 MHz transmission Water resistant casing Wall mounting and table standing SETTING UP When one transmitter is used 1 First insert the batteries to the transmitter see How to install and replace batteries in the Temperature transmitter below 2 Within 2 minutes of powering up the transmitter insert the 43 batteries to the Temperature Station see How to install and replace batteries in the Temperature station below Once the batteries are in place all segments of the LCD will light up briefly Following the indoor temperature and the time as 0 00 will be displayed If they are not shown in LCD after 60 seconds remove the batteries and wait for at least 60 seconds before reinserting them Once the indoor data is displayed user may proceed to the next step After the batteries are inserted the Temperature Station will start receiving data signal from the transmitter The outdoor temperature should then be displayed on the Temperature 44 station If this does not happen after 2 minutes the batteries will need to be removed from both units and reset from step 1 4 In order to ensure sufficient 915 MHz transmission however there should be a distance of no more than 330 feet between the final position of the Temperature Station and the transmitter see notes on Positioning and 915 MHz Reception Using Multiple Sensors with One Temperature Station 1
8. equences 84
9. es will need to be replaced the low battery icon will appear on the LCD To install and replace the batteries please follow the steps below 1 Lift up the battery compartment cover 2 Insert batteries observing the correct polarity see marking 3 Replace compartment cover 50 HOW TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE TRANSMITTER The Temperature transmitter uses 1 x IEC CR2032 3 0V battery When battery needs to be replaced the low battery icon will appear on the LCD of the Temperature Station or replace battery every 12 months To install and replace the batteries please follow the steps below 1 Remove the battery compartment cover at the back of the transmitter 2 Insert the battery observing the correct 0e polarity see marking i f 51 o0 3 Replace the battery cover on the unit Note In the event of changing batteries in any of the units all units need to be reset by following the setup procedures This is because a random security code is assigned by the transmitter at start up and this code must be received and stored by the Temperature Station in the first few minutes of power supplying BATTERY CHANGE It is recommended to replace the batteries in all units every 12 months to ensure optimum accuracy of these units 52 Please participate in the preservation of the environment Return used batteries to an authorized depot 53 FUNCTION KEYS Temperature Station T
10. he Temperature Station has two easy to use function keys __ MIN MAX key SEEN key Setting Channel Press and hold for about 3 seconds to enter the Manual setting mode Press shortly to toggle between different channel readings MIN MAX key Min Max temperature Use to toggle between the minimum and maximum recorded readings of indoor amp outdoor temperature Press and hold to reset minimum and maximum record when min or max record is shown 55 LCD SCREEN AND SETTINGS TIME 2351 INDOOR g F Outdoor Channel No ID Indoor Temperature in C OUTDOOR 2 o gz a Outdoor Outdoor Reception M Temperature in C Sona eor a Receiver Low Transmitter Low battery indicator battery indicator When the signal from the transmitter is successfully received by the Temperature Station this icon will be switched on If not successful the icon will not be shown on the LCD User can therefore easily see whether the last reception was successful ON icon or not OFF icon On the other hand the short blinking of the icon shows that a reception is being done at that time For a better display clarity the LCD screen is split into 3 sections showing the information of time indoor temperature and outdoor data 57 Section 1 TIME Display of time manually set Section 2 INDOOR TEMPERATURE Display of indoor temperature Section 3 OUTDOOR TEMPERAT
11. nd casings Do not submerge the units in water Furthermore fix all parts in place where the units are adequately protected against moisture and rain Immediately remove all low powered batteries to avoid leakage and damage Replace only with new batteries of the recommended type Do not make any repair attempts to the unit Return them to their original point of purchase for repair by a qualified engineer 74 Opening and tampering with the unit may invalidate their guarantee v Do not expose the units to extreme and sudden temperature changes this may lead to rapid changes in forecasts and readings and thereby reduce their accuracy SPECIFICATIONS Temperature measuring range Indoor k 14 1 F to 139 8 F with 0 2 F resolution 9 9 to 59 9 C with 0 1 C resolution OF L displayed if outside this range 75 Ou Ind Ou door 39 9 C to 59 9 C with 0 1 C resolution 9 9 to 59 9 C with 0 1 C resolution OF L displayed if outside this range loor Temperature checking interval every 15 seconds door data checking interval every 16 seconds Power Supply Temperature Station 2 x AAA IEC LR3 1 5V Ou Bal door Temperature Transmitter 5 1 x IEC CR2032 3 0V tery life cycle approximately 12 months Alkaline batteries recommended 76 Dimensions L x W x H Temperature Station 3 2 29 x 69 x 4 66 58 2 x 17 6 x 118 4 mm Outdoor Temperature Transmitter 1 44 x 53 x
12. on related circumstances LA CROSSE TECHNOLOGY LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL CONSEQUENTIAL PUNITIVE OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION THIS PRODUCT IS NOT A TOY KEEP OUT OF CHILDREN S REACH 81 This warranty gives you specific legal rights You may also have other rights specific to your State Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you For warranty work technical support or information contact La Crosse Technology Ltd 2809 Losey Blvd S La Crosse WI 54601 Phone 608 782 1610 Fax 608 796 1020 82 e mail support lacrossetechnology com warranty work sales lacrossetechnology com information on other products web www lacrossetechnology com 83 Questions Instructions Please visit www lacrossetechnology com 9121 All rights reserved This handbook must not be reproduced in any form even in excerpts or duplicated or processed using electronic mechanical or chemical procedures without written permission of the publisher This handbook may contain mistakes and printing errors The information in this handbook is regularly checked and corrections made in the next issue We accept no liability for technical mistakes or printing errors or their cons
13. s 2 Avoid positioning the Temperature Station onto or in the immediate proximity of metal window frames 66 3 Using other electrical products such as headphones or speakers operating on the same signal frequency 915MHz may prevent correct signal transmission and reception 4 Neighbors using electrical devices operating on the 915MHz signal frequency can also cause interference Note When the 915MHz signal is received correctly do not re open the battery cover of either the transmitter or the Temperature Station as the batteries may spring free from the contacts and force a false reset If this happens accidentally all units must be reset see Setting up above otherwise transmission problems may occur 67 The transmission range is about 330 ft 100 m from the transmitter to the Temperature Station in open space However this depends on the surrounding environment and interference levels If no reception is possible despite the observation of these factors all system units have to be reset see Setting up above f i235 POSITIONING THE TEMPERATURE STATION The Temperature Station comes attached with foldout table stand which provides the option of table standing the unit in addition 68 to wall mounting Before wall mounting please check that the outdoor temperature values can be received from the desired locations To wall mount 1 Fix a screw not supplied into the desired wall G A 7
14. t in need or repair you will be charged for the repairs or examination The owner must pay any shipping charges incurred in getting your La Crosse Technology Ltd product to a La Crosse Technology Ltd authorized service center La Crosse Technology Ltd will pay ground return shipping charges to the owner of the product to a USA address only 79 Your La Crosse Technology Ltd warranty covers all defects in material and workmanship with the following specified exceptions 1 damage caused by accident unreasonable use or neglect including the lack of reasonable and necessary maintenance 2 damage occurring during shipment claims must be presented to the carrier 3 damage to or deterioration of any accessory or decorative surface 4 damage resulting from failure to follow instructions contained in your owner s manual 5 damage resulting from the performance of repairs or alterations by someone other than an authorized La Crosse Technology Ltd authorized service center 6 units used for other than home use 7 applications and uses that this product was not intended or 8 the products inability to receive a signal due to any source of interference This warranty covers only actual defects within the product itself and does not cover 80 the cost of installation or removal from a fixed installation normal set up or adjustments claims based on misrepresentation by the seller or performance variations resulting from installati
15. third transmitter as soon as the channel 2 icon and outdoor data are displayed on the temperature station Then within 2 minutes the channel 3 outdoor data from the third transmitter will be displayed and the channel icon will shift back to 1 once the third transmitter is successfully received If this is not happen user shall restart the setting up from step 1 Note User shall insert the batteries into the third transmitter within 45 seconds of reception of the second transmitter 8 In order to ensure sufficient 915 MHz transmission however this should under good conditions be a distance no more than 100 48 meters between the final position of the Temperature Station and the transmitter see notes on Positioning and 915 MHz Reception IMPORTANT Transmission problems will arise if the setting for additional sensors is not followed as described above Should transmission problems occur it is necessary to remove the batteries from all units and start again the set up from step 1 If the signal reception is not successful on the first frequency 915MHz for 14 seconds the frequency is changed to 920MHz and the learning is tried another 14 seconds If still not successful 49 the reception is tried for 14 seconds on 910Mhz This will also be done for re synchronization HOW TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE STATION The Temperature Station uses 2 x AAA Alkaline batteries When batteri
Download Pdf Manuals
Related Search