User`s manual
Contents
1. lever can be easily pushed to the CLOSE position this to enable the wheel to be easily installed and removed means the clamping strength is insufficient Return the quick release lever to the position perpendicular to the bicycle frame and again turn the adjusting nut clockwise to increase the clamping trength Push the quick release lever back to the CLOSE position Adjusting nut Quick Release function When the quick release lever is brought to the closed position the lever nut moves inward The force of this clamps the wheel to the frame and holds the wheel securely in place CLOSE position Adjusting nut Lever nut os Open position Quick release lever The clamping strength is adjusted by turning the adjusting nut When the nut is turned in a clockwise direction the clamping strength increases and when the nut is turned in a counter clockwise direction the clamping strength decreases Stronger g Adjusting nut N A AS Weaker s E J t Suitable dimensions of the rear end Be sure to use only rear end widths with suitable dimensions cannot use fork thicknesses less than 5 mm 1 Move the quick release lever to the OPEN position and set the wheel so it firmly touches the interior of the rear end See sketch below Dura Ace 600 Ultegra not less than 6 mm 2 Open and close the quick release lever with your right hand while gradually tightening the adjusting nut with your lef2. UM 3TKOA 000 00 User s manual e If the clamping strength is adjusted too strong and the quick release lever cannot be pushed to the CLOSE position turn the adjusting nut in a counter clockwise direction to reduce the clamping strength When doing Rea r Fre h Li b this do not fully release the adjuster nut Turn it 1 8 of a revolution and then try to push the lever to CLOSE to set the maximum clamping for Cross Country strength with which you can push the quick release lever to the CLOSE position User s manuals in other languages are available at http si shimano com INTRODUCTION i sige Turn 1 8 revolution 2 at a time e Contact the place of purchase or a bicycle dealer for information on e Products are not guaranteed against natural wear and deterioration from installation and adjustment of the products which are not found in the normal use and aging user s manual A dealer s manual for professional and experienced bicycle e For maximum performance we highly recommend Shimano lubricants and mechanics is available on our website http si shimano com maintenance products Do not disassemble or alter this product For safety be sure to read this user s manual thoroughly before use and follow them for correct use ct ions before riding the bicycle Before riding the bicycle check the following items If any problems are found with the following items contact the place of purchase or a bicycl
3. e dealer important Safety Information e Are the wheels fixed Guidelines that require replacement contact the place of purchase or a Do the wheels rotate smoothly bicycle dealer e Are there any abnormal noises A WARNING e Check that the wheels are fastened securely before riding the bicycle If Names of parts the wheels are loose in any way they may come off the bicycle and serious injury may result o If the quick release lever is on the same side as the rotor there is the danger that it may interfere Quick release j with the rotor Make sure that even ifthe quick E ay release lever is tightened with your palm with all your strength the quick release lever does not interfere with the rotor If the lever interferes Rotor with the rotor stop using the wheel and consult a dealer or an agency e After reading the user s manual carefully keep it in a safe place for later reference e Never fasten a wheel to a frame by rotating the quick release lever as shown in the diagram on the right Simply rotating the lever in a circular motion will not fasten the wheel to the frame Detachment of the wheel as a result of improper hub installation can result in serious bodily injury Note e Do not apply any lubricant to the inside of the hub otherwise the grease What is a Quick Release will come out It is a mechanism that uses a single quick release lever operation on the hub e If the quick release
4. t hand in the clockwise direction Continue tightening th nut until you feel resistance with your hand at the point when the lever is parallel to the hub as indicated by the dotted position in the diagram on the right Quick release lever 3 Grip the rear end with your fingers and use the palm of your hand to close the quick release lever with as much strength as possible When closed the quick release lever must be in the CLOSE position shown below in the diagram on the right The side of the lever with the inscription CLOSE must be facing away from the bicycle and the lever should be parallel to the rear end as shown below in the diagram on the left Positioning of the quick release lever For safety the quick release lever should be along the bicycle frame when in the CLOSE position Removing the wheel Move the quick release lever from the CLOSE position to the OPEN position Loosen the adjusting nut and then remove the wheel SHIMANO SHIMANO AMERICAN CORPORATION One Holland Irvine California 92618 U S A Phone 1 949 951 5003 SHIMANO EUROPE B V Industrieweg 24 8071 CT Nunspeet The Netherlands Phone 31 341 272222 SHIMANO INC 3 77 Cimatsu cho Sakai ku Sakai shi Osaka 590 8577 Japan Please note specifications are subject to change for improvement without notice English Jan 2012 by Shimano Inc HTR SZK
Download Pdf Manuals
Related Search