Home

CommandCall CC1

1. and horn consist of 6 wires Grey wire of car engine blocking is permanently grounded 300 mA till the moment of activating car engine blocking function when this signal is disabled Car engine blocking relay must be connected with no power consumption when the car ignition is turned OFF The remaining wires must be isolated separately Wait approximately 30 seconds after power on CommandCall till GSM module will register to A N mobile network operator After successful registration of the unit to the GSM network it is ready to receive SMS commands and to send SMS reports to the user Actual operation state of the control unit and its GSM module are indicated by red and green LEDs the indication is described in table at the end of chapter 5 Supplementary functions 5 13 CommandCall CC1 20 11 Trouble shooting Actual status Possible reason Measures to be taken system does not check the fuses and all connections respond weak GSM signal check GSM antenna change vehicle position change CommandCall in car installation location command is executed no credit on SIM card check remaining credit on SIM card no SMS sent to user short circuit remove the short circuit on output s and wait approximately 10 minutes system will recover automatically lf the problem persist RESET the system lf the problem still persist contact authorised service centre system ignore incorrect SMS command system intentionally ignores SMS commands star
2. or Rejected within 10 seconds by the driver of the vehicle the heater will be switched ON and phone call terminated If the checkbox No 4 is activated system will send SMS No 4 to callers phone Remaining time and temperature is shown only if respective checkboxes No 31 and 32 are activated connectivity test by sending SMS No 21 in set time period indicating system operability amano eevee monitoring for 10 minutes after Alarm trigger signal received ee ee e L monitoring for 10 minutes after SOS function activation Command code Switch ON the heater by phone call ia Monitor enable when car engine blocking Activating the checkbox No 24 will automatically enable monitoring for 10 minutes after engine blocking activation 320 Setting UST temperature User Set Temperature System Receiving SMS command in form xxxx320ttt t xxxx is user 320 UST ttt t C OK fix compares actual in car temperature with UST value when password will set UST to ttt t value ttt t is temperature exceeded system will send respective SMS report to user value in range 40 0 to 125 0 degrees Celsius Setting time delay TS during which must actual temperature Receiving SMS command in form xxxx321sss xxxx is user 321 TS sss seconds OK exceed UST value to be recognized as limit level break password will set TS to sss value sss is time ha in range for exclusion of short term temperature change seal
3. push button e g if heater was switched ON by external clock then SMS command xxxx000 xxxx is user password or pressing ON OFF push button will have no effect It means when the heater is ON by external clock it is not possible to switch it OFF by SMS command or by ON OFF push button and vice versa CommandCall CC1 14 7 CommandCall USB Programming Adapter CommandCall control unit programming is possible with using USB Programming Adapter USB Programming Adapter is interface device for connecting CommandCall control unit with PC and to use CommandCall PC Setup In the case your computer does not recognize inserted USB Programming Adapter it is necessary to install USB to COM port converter utility USB to UART conversion Close all applications before inserting USB Programming Adapter into USB port of your PC LED built in USB Programming Adapter flashes only during active data transfer between CommandCall control unit and PC Setup programme CommandCall USB Programming Adapter is Accessory it is not included in CommandCall kit 8 USB to COM port converter In the case your computer does not recognize inserted USB Programming Adapter it is necessary to install USB to COM port converter utility USB to UART conversion USB to COM port converter utility installation procedure is described in Chapter 13 of this manual Check if your computer recognised inserted USB Programming Adapter a insert USB Programming Adapter to any free U
4. 21 Periodical connectivity test OK every 15 days The user has possibility to recognize that something wrong happened to CommandCall if he she does not receive SMS report in expected time It can be caused by system malfunction or just by missing credit for sending SMS reports For activating this feature checkbox No 21 must be set active and desired time interval for sending SMS report set by combination of 3 values number of days hours and minutes These values can be freely combined in allowed ranges for example SMS report sending can be repeated every 5 days and 14 hours and 23 minutes of course it is necessary to set up meaningful time period Note System RESET will clear the counter of elapsed time from last SMS report sent to the user CommandCall CC1 13 6 ON OFF push button functions with orange LED indication Switch the Short pressing of the push button max 1 second Status After push button release LED heater ON will be changed after button release system reacts on will lit ON indicating heater signal fall down edge status ON If checkbox No 5 is set active the system will send SMS report Eberspaecher ON by switch The heater will be ON depending on time preset by SMS command 281 in the range of 1 to 120 minutes Timer preset value 999 will cause heater switch ON for unlimited time Timer preset value is possible to change also by CommandCall PC Setup during system installation Switch the
5. 25 or 26 depending on situation explained in the chart temperature C _ Example A Example B as a 2i R na System will send SMS No 25 No SMS sent actual System will send SMS No 26 time Temp decreased bellow UST temperature did not Temperature increased over UST exceeded UST for longer time than TS CommandCall CC1 12 The values UST1 and UST2 are in the system handled as temperature interval System monitors actual temperature entering and leaving interval limits and the direction of temperature changes temperature increase or decrease If the limit value is exceeded and the temperature is stable behind the limit value for time period longer than parameter value TS1 system will send to the phone number No 1 SMS report No 27 28 29 or 30 depending on situation explained in the chart temperature A system sends SMS No 28 Temp increased into interval l TSI B no message sent stability Eai AALAN Jo period not reached TS TS1 a a C system sends SMS No 30 UST2 N O Temp left interval up T51 D system sends SMS No 27 Temp decreased into interval e E system sends SMS No 29 A B C D E Temp left interval down 5 11 Speaker volume Speaker volume may be set by dial on the speaker body 5 12 Short circuit If the short circuit occurs on the outputs of the CommandCall heater signal 300 mA or car engine blocking signal 300 mA system will send SMS re
6. E Folders Ez Cs A 7 My Computer 5 My compute f omedia a E System Properties rlash ou System Tasks q aae S Local D System Restore amp Fa j view system information General Computer N 3 My Network slovnik T evo ore programs ae Go Change a setting Se DATA E Device Manager tats all the hardware devices installed Device Manager e Device Manager to change the Places Tene Fie Action View Help 42 3 8a4 Se Keyboards Mice and other pointing devices ake sure that installed drivers are Bo Modems s Windows Update lets you set up 2 Monitors to Windows Update for drivers Windows Update Ports COM amp LPT a7 BT Port CONJA Pe ABA ioe E i k b i ht e a way for you to set up and store ov BT Port COM12 IC y rig urations aF BT Port COM13 b tt Y er pert cone THOS DUUON amaer a BT Port COM20 Hardware Profiles a BT Port COM21 ti BT Port COM40 a7 BT Port COME Disable seminar r L J Secure Digital host controllers Sound video and game controllers Uninstall Opens property sheet For the current selection Properties pe a o ooa i ne Gai Ad Aware SE Rhinoceros rozhlas banner CommandCall SAF p Professional start I OE WW my Computer Device Manager fy Adobe Photoshop By selecting one of free COM ports with lower number from the list the COM port number assignment will be changed accord
7. O to 999 seconds The checkbox No 25 UST exceeded temperature Activating the checkbox No 25 will enable sending SMS Temp decreased below UST 25 decreasing No 25 in the case actual temperature decreases under UST and stay bellow UST longer than specified time TS The checkbox No 26 UST exceeded temperature Activating the checkbox No 26 will enable sending SMS Temp increased over UST increasing No 26 in the case actual temperature increases over UST and stay over UST longer than specified time TS 322 Setting UST1 temperature upper temperature interval limit Receiving SMS command in form xxxx322ttt t xxxx is user 322 UST1 ttt t C OK 18 fix System compares actual in car temperature with UST1 password will set UST1 to ttt t value ttt t is temperature value when exceeded system will send respective SMS value in range 40 0 to 125 0 degrees Celsius 323 Setting UST2 temperature lower temperature interval limit Receiving SMS command in form xxxx323ttt t xxxx is user 323 UST2 ttt t C OK 18 fix System compares actual in car temperature with UST2 password will set UST2 to ttt t value ttt t is temperature value when exceeded system will send respective SMS value in range 40 0 to 125 0 degrees Celsius Note UST1 gt UST2 324 Setting time delay TS during which must actual temperature Receiving SMS command in form xxxx324sss xxxx is user 324 TS1 s
8. Short pressing of the push button max 1 second Status After push button release LED heater OFF will be changed after button release system reacts on will switch OFF indicating heater signal fall down edge status OFF If checkbox No 2 is set active the system will send SMS report Eberspaecher OFF by switch Pressing of the push button for at least 5 seconds max 20 After 5 seconds LED will flash seconds Status will be changed after button release for 5 seconds indicating to system reacts on signal fall down edge release the push button If checkbox No 15 is set active the system will send SMS report S O S to all stored phone numbers Accept phone Short pressing of the push button max 1 second during During ringing of incoming call ringing of incoming phone call will accept the call Status will LED flashes slowly after be changed after button release system reacts on signal accepting the call LED flashes fall down edge faster Function is active only when checkbox No 19 is set active After phone call termination LED will switch OFF Terminate Short pressing of the push button max 1 second during After phone call termination LED phone call active phone call will terminate the call Status will be will switch OFF changed after button release system reacts on signal fall down edge Reject Pressing of the push button for at least 2 seconds during After phone call rejecting LED phone
9. below UST 26 1 Temp exceeded UST up Temp increased over UST Temperature limit 5 USTCE fo TS seconds 27 0 Temp entered interval from top Temp decreased into interval 28 Temp entered interval from down Temp increased into interval 29 Temperature left interval down Temp left interval down ar Temperature left interval up Temp left interval up Temperature interval 25 usme fzo Heater timer preset 2 0 HTF minutes 31 Remaining heating time add to SMS report No 4 5 7 11 32 Actual in car temperature add to SMS report No 1 2 3 4 5 6 7 11 33 ad Heater OFF Eberspaecher OFF 34 Password Change Password change OK 35 Short circuit Password disable CE 36 Password disable usTarc 20 TStjseconds Request Apply initialize In this manual the whole content of CommandCall PC is displayed in a single screen during normal work with PC Setup you have to scroll the content in smaller window CommandCall CC1 17 Here are shown parts of PC Setup screens with description of their purpose and the way how to use them x CommandCall PC Setup i m Unit Information Password Setting Change Password Password disable Version 1 10 New i SIMPIN 0000 Confirm Default Unit information Version shows actual version of program stored in CommandCall control unit SIM PIN insert PIN code of the SIM card which is used in CommandCall 9 1 Password sett
10. call ringing of incoming phone call will reject the call Status will will stop flashing be changed after button release system reacts on signal fall down edge Function is active only when checkbox No 19 is set active system Pressing of the push button for at least 40 seconds will reset After 5 seconds LED will flash 5 RESET the system times please keep push button System RESET will restart CommandCall control unit will pressed restart GSM module resets outputs overload protection When the time 40 seconds is circuits and clears all internal counters reached LED will flash 4 times System RESET will not change checkboxes settings or release the push button now preset values UST TS timer preset After release of push button Status will be changed after button release system reacts LED will be ON for 2 seconds to on signal fall down edge indicate system RESET Emergency When Anti car jacking car engine blocking function is disarming activated switch ON the ignition ACC ON and press push button 5 times within 8 seconds Car engine blocking will be released Backup Pressing of the push button for at least 20 seconds when All LEDs will switch OFF battery cut the power is OFF will cut OFF CommandCall backup battery OFF Heater control by SMS commands and using ON OFF push button can be freely combined Control signals of heater external clock can not be override by SMS commands or by using ON OFF
11. mA GSM module parameters Siemens TC35i Working temperature range 20 C up to 55 C Storage temperature range 40 C up to 80 C Dimensions of control unit 96 x 75 x 27 mm wide x depth x height net weight 100 grams Dae CommandcCall unit is electronic device and thus can not be disposed as communal waste Used product dispose at dedicated recycling collection spot eS This unit contains plastics and other recyclable materials CE This product was tested and approved for use in accordance with relevant EC directives CommandCall CC1 30 This product conforms with the type approved by Ministry of Transport Post and Telecommunication of the Slovak Republic on September 28 2007 under Approval No E27 10R 02 1199 00 and EC type approval No e27 72 245 2006 96 1011 00 For this product following marks were alloted 10 R 02 1199 l 03 1011 Copyright 2007 MOLPIR s r o All rights reserved it is prohibited to copy reprint or to circulate any part of this Manual without prior written consent of the author Product parameters are subject to change without prior notice LITINA MOLPIR s r o Hrachov 30 821 05 Bratislava tel 421 243 191 218 fax 421 243 191 220 www molpir sk obochod molpir sk CommandCall CC1 31
12. numbers max 4 phone numbers After power cut is detected system sends SMS report to all Power cut 16 16 stored phone numbers max 4 phone numbers When systems gets signal from the car alarm and later ACC trigger ignition is switched ON ACC ON system will send SMS report No 17 to all stored phone numbers max 4 phone numbers for sending SMS reports Activating the checkbox No 18 will enable sending confirmation SMS after execution of those commands which do not have specific checkbox Activate built in phone Activating the checkbox No 19 will enable phone calls on 19 built in phone in CommandCall Incoming phone call is indicated by flashing LED of ON OFF push button and ringing tone in the speaker if connected E ACC ON ignition Command execution confirmation Functions Accept Reject and Terminate the phone call by ON OFF push button are activated If the checkbox 19 is not activated it is not possible to make phone call on CommandCall built in phone such phone call is not indicated except 10 minutes of monitoring enabled CommandCall CC1 8 Command Description Text of SMS report Check SMS box report Activating the checkbox No 20 will enable to switch the 20 heater ON by phone call to CommandCall Incoming phone call is indicated by flashing LED of ON OFF push button and ringing tone in the speaker if connected If incoming phone call is not Accepted
13. 88 Change of phone number 4 Receiving SMS command in form xxxx288MMM xxxx is 288 OK 18 fix user password will set the fourth phone number for sending SMS reports NNN is country code TT T is phone number Command xxxx288 will erase the fourth phone number 290 Checkboxes settings Receiving SMS command in form xxxx290NNNN N xxxx 290 OK 18 fix is user password will set all checkboxes as specified by respective N Each N can contain 0 for deactivating and 1 for activating of respective checkbox The number of respective checkbox is given by position in the sequence 2 and 1 activated respective checkbox The position in the sequence gives number of the respective checkbox 1 32 nvalid command Receiving SMS command with wrong user password Invalid command 13 13 command code or parameter value is rejected and SMS No 13 is sent to the user Alarm trigger When systems gets signal from the car alarm it will send Alarm trigger 14 14 SMS report No 14 to all stored phone numbers max 4 phone numbers for sending SMS reports 15 15 91 Request on actual setting of checkboxes Receiving SMS command in form xxxx291 xxxx is user 291 OK NNNN fix password will send SMS containing sequence of 32 characters 0 or 1 where each 0 means deactivated i SOS Pressing ON OFF push button for at least 5 seconds max S O S 20 seconds will send S O S report to all stored phone
14. Installations instructions During in car installation follow this Installation manual instructions as well as instructions given by car manufacturer concerning installation operation and usage of mobile phone or GSM module in the car CommandCall control unit install beneath dashboard of the vehicle as low as possible regarding extreme high temperatures in Summer Fix the control unit properly with connectors pointing down to avoid on wires condensed water to leak in the control unit Small rod GSM antenna included in the kit or external GSM antenna on glass stick on type with higher signal gain optional accessory must be connected to CommandCall control unit The external GSM antenna is mounted from interior on the windshield or rear car window Clean and dry the place where the antenna will be stick on first tear off protection film from the antenna and stick on the antenna firmly Install antenna cable to control unit and screw the connector to SMA connector on the control unit For the cars with metallized glass windows consider using GSM external roof type antenna GSM signal level always depends on local conditions and GSM network coverage Take care when installing SIM card in the control unit as the card holder is tiny mechanical part and can be damaged or broken when manipulated wrong way Controls installation ON OFF push button install in the working area of the driver in place where is no risk of unwanted operation for e
15. LITINA CommandCall CC1 GSM communication module User amp Installations Manual Order Number 206300322700 Controll SW 1 14 Contents t tems Suppled es acest ataaesiSs E 2 Ist GSM GommandGall swersdishrardceteseehaticdeendes arent A TE EERE 2 T2 ACCOSSONGS go q qj qj diiss slcsuncteadedudascecumensuuvie wie usnaiwatdoeuulcevnisesuuieucccsue 3 2 MGENEVal GGSCriIDUOM hehe tne cect e ten Cae AE 3 21 Me Way OrCcOMmuUnication aa R 3 22 IMEIOMMAUOLOMS COMMaANG A a eects 3 2 3 COntent or oSMS Tepon O O a alee cuit eau eencieel asia baas oid 4 2 4 Switching ON the heater by phone Call eae e ee eeeccceeccccaeeeeeceeseeceeeeeseeeeeeseeeeseeeeeseaeeeeseaeeesaees 4 2o Alanger teen c cD atnhGaind uaa E 4 3 C ntrolcommands O aaeei 5 A IBASIGCOMIMAMOSOVEIVICW etait eh hace Sl tt cl a eh thd Ste deeded nat the 11 5 SUDPIGMENIGRVIUNCIIONS eee ete ta a ceed tice Mate 11 SPANG itd auntdeeca teas eels actnars CES Anata ier eee ane anal nee eeneieaatie 11 52 Carengine DIOCKING O AATE eOr AE e wvebhaw EAR 11 5 3 Emergency release of blocking ni aaecccesceceececteseeceuceceueccueecsueeceseecsusessusesseseessusenees 11 5 4 Emergency ask for help SOS fUNCHON sivsesnkenniaen ia 11 Oro MONARO A 11 SOrOVSIEMNCSCl a oe eel otal dee ee dad en a eee 12 Ore BaCk UP DANeryCUE O cing eh es earls seek Sha a tecadie N tne ted Eara 12 DOrrOWCRCUL 2 4 EE 12 5 9 Accepting and terminating of inc
16. O 10 Command Description Text of SMS report Check SMS box Command code 011 Switch ON the heater for 11 minutes Receiving SMS command in form xxxx011 xxxx is user Eberspaecher ON MMM min password will switch ON the heater and 11 minutes later ttt t C will switch it OFF When switching ON the heater SMS No 11 is sent Remaining time and temperature are shown only if respective checkboxes No 31 and 32 are activated Switch ON the heater for 12 to 119 minutes A icici Cent ulead ON MMM min ttt t C 120 Switch ON the heater for 120 minutes Receiving SMS command in form xxxx120 xxxx is user Eberspaecher ON MMM min password will switch ON the heater and 120 minutes later ttt t C will switch it OFF When switching ON the heater SMS No 11 is sent Remaining time and temperature are shown only if respective checkboxes No 31 and 32 are activated Setting heater timer preset HTP value Receiving SMS command in form xxxx281MMM xxxx is user password will set heater timer preset to specified value MMM is value in range 1 to 120 minutes For MMM 999 the heater will be switched ON unlimited Monitoring enable Receiving SMS command in form xxxx282MMM xxxx is user password will enable monitoring of the vehicle for 10 minutes from receiving the command After calling on built in phone in CommandCall within 10 minutes the call is automatically accepted without any indication in the vehicle no ringi
17. SB port on your PC run Device Manager on your PC and check available COM ports by executing sequence of highlighted commands in defined order first double click on left mouse button on My Computer icon to open pop up window My Computer then click with left mouse button on View system information in section System Tasks then click on Hardware etc T noa My Computer MM VIBOCome rts icles E re Fore ssi J a Ka Search ar Folders FEE t System Properties l System Restore j Automatic pdate Remote EEE A General j Computer Ns 2 Hardware Mylanced i Bl a t FEP T Add or remove programs My Network aint G Change a setting Places Device Manager sa oT he Device Manager lists all the hardware devices installed i on your computer Use the Device Manager to change the al el py properties of any device ea TaD l Device M Device Manager ES 4 k Fie Action view Help a aA gre that installed drivers are e gt dows Update lets you set up See Disk drives A dowe Update for drivers a Display adapters y l 3 DWDJCD ROM drives iq Human Interface Devices IDE ATASATAPT controllers ea IEEE 1394 Bus host controllers 38 Imaging devices gt Keyboards 1 Mice and other pointing devices l Modems i Monitors At E8 Network adapters T roe CnaT m a BT Port COM10 v for you to set up and store hs T re 7 re re re T T T dip
18. SMS command in form xxxx325dd xxxx is user 325 PTD dd days value password will set PTD to dd value dd is in range 0 to 99 fix 326 Setting number of hours for Periodical connectivity test Receiving SMS command in form xxxx326hh xxxx is user 326 PTH hh hours fix PTH value password will set PTH to hh value hh is in range 0 to 24 327 Setting number of minutes for Periodical connectivity test Receiving SMS command in form xxxx327mm xxxx is user 327 PTM mm minutes fix PTM value password will set PTM to mm value mm is in range 0 to 60 If temperature sensor is not present or is defective the system will send string instead of temperature value Temperature values set by commands 320 322 323 may contain only numbers decimal digits minus sign for negative values and decimal point as separator of decimal portion of the value gt Example of setting checkboxes by command 290 SMS command in format xxxx29010011111010101000000010100001011 will set checkboxes No 1 4 5 6 7 8 10 12 14 22 24 29 31 and 32 to status activated and checkboxes No 2 3 9 11 13 15 16 17 18 19 20 21 23 25 26 27 28 30 to status disabled xxxx is user password Note For setting checkboxes by using command 290 it is suggested to use command 291 first to get actual checkboxes settings and then to edit received SMS in users mobile phone to
19. activated monitoring period will be indicated by LED flashing LED in ON OFF push button and by ringing in the speaker if soeaker is connected to the system speaker is an Accessory not included in CommandCall kit In the case the speaker is installed in the system user can make standard phone call to vehicle 5 6 System Reset Pressing the ON OFF push button and keeping it pressed for at least 40 second will lit ON LED for 2 seconds and system will RESET LED will flash 5 times after push button is pressed for 5 seconds please ignore this flashing and keep push button pressed When 40 seconds time is reached LED will flash 4 times release the push button now System RESET will restart CommandCall control unit will restart GSM module reset outputs overload protection circuits and will clear internal counters Reset will clear also counter of elapsed time for periodical connectivity test e g if Periodical connectivity test is activated the time for sending relevant SMS report starts from scratch again RESET will not change checkboxes settings or parameters values UST TS timer preset 5 7 Back up battery cut off CommandCall has internal backup battery for limited time operation when power supply is cut OFF When the power supply is OFF press and keep ON OFF push button pressed for 20 seconds LED will flash twice when time 20 second is reached release the push button now The back up battery is cut OFF
20. al CommandCall CC1 1 1 Items supplied 1 1 GSM CommandCall CC1 consist of following parts CEJ CommandCall 1 Control unit 2 Heater wire harness 3 5 Connectors terminals 6 Accessories wire harness 7 ON OFF push button 8 GSM antenna 9 Microphone CommandcCall CC1 wa f TeJas jCommandCal Independent heater control mares through SMS commands Conmmanctiall Code Command e i 0 Switch OFF the heater j 1 Switch ON the heater for preset time 2 Actual status of the heater 3 Remaining heating time and actual temperature 0 Switch ON the heater for 10 minutes Utivatelska a in tala n prirutka User amp Installations Manual Betriebs und Einbauanweisung eee tn eee re i Switch ON the heater for 120 minutes F SMS format xaM NA oo is user password NNN is command code tamer 206300322700 K 10 Temperature sensor 11 User manual 12 Basic commands card Item Item description Qty Orderingcode __ CommandCall CC1 full set 1 206300322700 6 Accessories wire harness 1 206300801102 8 GSMantenna SS 9 CommandCall CC1 2 1 2 Accessories The CommandCall CC1 functionality may be extended added with following parts 4 5 Blocking relay 1 USB Programming Adapter 2 GSM window antenna 3 Speaker 6 Relay wire harness Item description CommandCall USB Programming Adapter Blocking relay 12V 30A 2 1393302 2 Blocking relay 24V 20A 5 1393302 1 6 Relay wi
21. al temperature 005 006 007 Command Request for actual in car temperature Panic Anti car jacking car engine blocking if ignition of the vehicle is OFF ACC OFF when blocking command is received the system will cut off fuel bump immediately and sounds horn intermittent for 30 seconds If ignition of the vehicle is ON ACC ON when blocking command is received the system will sound horn intermittent for 30 sec followed with 30 seconds pause This cycle can be repeated maximally 10 times System waits for switching ignition OFF When the ignition is switched OFF system will cut off fuel pump immediately and sounds horn intermittent for 30 sec Emergency release Switch ON the heater for 10 minutes CommandCall CC1 Description If the heater was switched ON by phone SMS command or phone call or by push button prior receipt of SMS command in form xxxx003 xxxx is user password the system will send SMS containing number of minutes remaining till switching heater OFF and actual in car temperature If the timer preset value 999 system will send SMS No 7 If the heater was switched ON by external clock the system will send SMS No 6 If the heater is OFF the system will send SMS No 33 In command 003 remaining heating time and temperature are shown regardless relevant checkboxes setting After receiving SMS command in form xxxx004 xxxx is user password system will send SMS containing value of measured temper
22. arning non authorised copying or commercial usage of this program or its part is prohibited All rights reserved CommandCall CC1 16 followed by opening of main window of the CommandCall PC Setup CommandCall PC Setup Unit Information Password Setting a l Change Password Version 4113 hear ay SIM PIN Confirm Phone numbers for sending SMS Phone 1 Phone 2 Phone 2 Phone 4 MSMS setting Eberspaecher OFF by SMS 1 M Heater OFF by SMS 2 Heater OFF by push button 3 7 Heater OFF by external clock 4 V Heater ON by phone 5 7 Heater ON by push button 6 7 Heater ON by external clock 7 7 Heater ON for unlimited time 8 Panic 9 Car engine blocking 10 1 Emergency release of blocking 11 1 Heater ON 12 1 Monitoring enable 13 Invalid command 14 7 Alarm trigger 15 7 9 08 16 Power cut 17 7 ACC trigger Eberspaecher OFF by button Eberspaeccher OFF by clock EFberspaecher ON by phone b Eberspaccher ON by Eberspaeccher ON by clock Eberspaecher unlimitted ON 18 1 Command confirmation 19 Phone activate 20 Heater start by phone call 21 Periodical connectivity test Periodic connectivity test OR Connectivity test every 15 PTD days 2 PTH hours o PTM minutes 99 Monitor Enable when Alarm 93 Monitor Enable when 5 0 5 24 Monitor Enable when blocking 25 1 Temp exceeded UST down Temp decreased
23. ature in degrees Celsius Working range of temperature sensor is 40 0 to 125 0 C In command 004 actual in car temperature is shown regardless checkbox No 32 setting After receiving SMS command in form xxxx005 xxxx is user password system will sound horn intermittent for 30 seconds and sends SMS No 8 to the user After receiving SMS command in form xxxx006 xxxx is user password system will start blocking procedure will cut fuel pump and will send SMS No 9 to the user If the checkbox No 24 is activated it is possible to make monitoring call within 10 minutes Monitoring call is automatically accepted without any sound or LED indication in the car Receiving SMS command in form xxxx007 xxxx is user password will release car engine blocking and sends SMS report No 10 Receiving SMS command in form xxxx010 xxxx is user password will switch ON the heater and 10 minutes later will switch it OFF When switching ON the heater SMS No 11 is sent Remaining time and temperature are shown only if respective checkboxes No 31 and 32 are activated Text of SMS report MMM min ttt t C Eberspaecher unlimited ON ttt t C berspaecher ON by clock ttt t C berspaecher OFF ttt t C ttt t C Panic OK Engine blocking OK Emergency release OK Eberspaecher ON MMM min ttt t C Check box SMS report fix N fix 00
24. automatically after sending repeated SMS report No 16 Power cut to all stored phone numbers After sending second SMS Power cut the system will switch OFF the backup battery and the whole system too 5 8 Power cut In any operation state of the system when the power is OFF for at least 5 seconds SMS report No 16 Power cut will be sent to all phone numbers stored in the memory of the CommandCall control unit maximal 4 phone numbers 3 minutes later the system will send SMS No 16 again After that system will cut OFF backup battery automatically 5 9 Accepting and terminating of incoming call While incoming call is ringing and checkbox No 19 is activated short press of ON OFF push button will accept incoming call Keeping ON OFF push button pressed for longer than 2 seconds incoming call will be rejected Pressing ON OFF push button during active phone call will terminate actual phone call 5 10 Exceeded temperature limits CommandCall enables to measure actual in car temperature and to compare it with 3 stored temperature limit values UST UST1 and UST2 UST is processed in the system as independent limit temperature value System monitors actual temperature reaching limit value UST and the direction of temperature changes If the limit value UST is exceeded and the temperature is stable behind the limit value for time period longer then parameter value TS system will send to the phone number No 1 SMS report No
25. e and location Just after using Apply function loaded data from the file are written into CommandCall control unit memory Exit quits the session of CommandCall PC Setup CommandCall PC Setup will read only firmware version from control unit after the start and will display it in upper left corner of the screen in section Unit information To display actual parameter j values press Request on bottom task bar of the CommandCall PC Setup screen To write actual parameters setting from the PC Setup screen into CommandCall control unit memory please press Apply on bottom task bar of the CommandCall PC Setup screen The communication of your PC with CommandCall control unit is automatically terminated after 5 minutes of idle period To restore normal activity of the unit exit PC Setup and start it again please In such case when system displays error message Communication failed during Request or Apply function it is recommended to store unsaved parameter settings into temporary file on your PC by using Save command then you can restart PC Setup and you can retrieve those parameters setting onto CommandCall PC Setup screen by using Load function to restore data from the temporary file and to continue your job Initialisation screen of PC Setup requests to enter COM port number even when CommandCall control unit is connected over the USB port of the computer CommandCall CC1 19 10
26. eecauntnedalenaskdenst cues 21 I VI dagran _ O Oa e seme OER 22 12 1 Wiring diagram CommandCall with independent heater one ee ec ceeeeeecccceseeeeeeeeeeeeeeeeaeeeeeeens 22 12 2 Wiring diagram CommandCall with independent heater and accessories _ eae eeeeaeeeeeeeaeee 23 1SoVV linStallationS ibid a Seale alain iia 24 13 1 USB t COM port COMVEFSION 6 edeeceaeb ore aeaea a an ata aeniei aa 24 13 2 CommandCall PC Setup Installation n essssessssnnssssnrnnsenrrensnrrrssnrnnssnrrnnsnnrrnsnrrenrnnrrnsnnrrennne 28 14 Technical specifications ance ceeseecaeeecesseceaceccueeeceucecsuuecsueeseeeessusessueesseetenees 30 The structure of this manual This manual describes single functions of GSM CommandCall the format of control SMS commands and reports sent to the user unit controls via installed in the vehicle and gives mounting instructions for unit installation in the vehicle and its connection with the independent heater Separate chapter Chapter 13 is describing SW tools installations necessary for parameter setting before unit installation in the car This information is not directly relevant for CommandCall functionality SW tools are just necessary tools in process of the unit installation in the vehicle Basic commands overview is helpful tool for the heater control in form of standard credit card which can be kept by the user all the time ready to use this sign shows important warnings and remarks in this manu
27. egulations In the case ignition is OFF ACC OFF when Blocking command is received the system will cut off relay of fuel pump immediately and will start the horn intermittent sound for 30 seconds In the case ignition is ON ACC ON when Blocking command is received the system will start the horn intermittent sound 30 seconds followed with 30 second pause This cycle can be repeated maximally 10 times and the system waits for switching OFF the ignition Immediately after switching OFF the ignition ACC OFF system will cut OFF fuel pump relay and will start the horn intermittent sound for 30 seconds 5 3 Emergency release When blocking function is activated switch the ignition ON and press ON OFF push button 5 times within 8 seconds The blocking function will be released 5 4 Emergency ask for help SOS function Any time the user will press and keep ON OFF push button pressed longer than 5 seconds maximally 20 seconds LED will flash for 5 seconds CommandCall will dial phone number No 4 stored in the memory and will ring 15 seconds After 15 seconds ringing system will terminate the phone call and will send SMS S O S to all stored phone numbers max 4 numbers In the case phone number No 4 in the memory is blank system will send S O S message to all stored phone numbers immediately If checkbox No 23 is activated system will enable monitoring call within 10 minutes from activating SOS function An
28. etup aa eae Installation Complete Recycle Bin ASUS Splendid fF R As JOR Technology j Desktop a My Documents ff P Shared Documents CommandCall PC Setup has been successfully installed Z F ig My Computer Click Close to exit Internet CyberLink DYD ERB My Network Places Explorer Suite Details CommandCall File Folder Date Modified 4 okt bra 2007 21 24 Please use Windows Update to check for any critical updates to the NET Framework vizualizacie p D 2 a Rhinoceros rozhlas banner 14 2 B CommandCall SAF creas to do paintball Oeers Adobe Photoshop Removable Disk Commandcall je GSM_GPSPC SE EN QJIE 3 C Pa 5 21 38 After installation is completed the program CommandCall PC Setup is ready to use Part of CommandCall PC Setup installation is the programme NET Framework 1 1 in the case it was not installed during Windows installation Programme NET Framework is part of legal installation of Windows operating system Programme CommandCall PC Setup can communicate with the user in one of 3 languages English German Slovak Selection of the language is available immediately after programme start in Select window CommandCall CC1 29 14 Technical specifications Model CommandCall CC1 DC power auto sensing 12V 24V DC power range 9V 35V Current draw GSM online 14 mA 25 mA Current draw sending SMS 60 mA Current draw voice and peak 120 mA 130
29. ew system information a LP T5 Add or remove programs Device Manager a P DATA My Network asm i Ch ttin ogy Places G AIAS e AEIR L The Device Manager lists all the hardware devices installed i on your computer Use the Device Manager to change the properties of any device wi Eoi i 2 Device Manager DE 4 Fie Action View Help 3 a Se Disk drives 32 Display adapters DYD CD ROM drives Human InterFace Devices 5 IDE ATAJATAPI controllers 4 IEEE 1394 Bus host controllers 38 Imaging devices Keyboards Mice and other pointing devices Modems iQ Monitors BB Network adapters re that installed drivers are Hows Update lets you set up A dows Update for drivers Windows Update for you to set up and store S Hardware Profiles ik ud 4 diplomovy seminar Ports COM amp LPT av BT Port COM10 Cancel a7 BT Port COM12 a7 BT Port COM13 a BT Port COM14 oy BT Port COM20 oy BT Port COM21 paintball FECIA G E Cc ba My Computer g Device Manager b if no one port among available COM ports is designed to USB Programming Adapter marked as UART Bridge Controller follow instructions given hereunder c remove USB Programming Adapter from the PC before removing USB Programming Adapter it is not necessary to perform activities usual for USB mem
30. he user after receipt of SMS command or user request switch ON or OFF the heater setting system parameter request on actual heater status and or in car temperature CommandCall answers to the user request by sending SMS report to the phone number from which original request command was sent to CommandCall Sending out of each respective SMS report is based on condition that relevant checkbox is activated during system installation by using CommandCall PC Setup The change of checkbox activation settings is possible any time by using SMS command 290 It is important to activate only those checkboxes which reports are necessary for proper user information and correct operation of the unit keep in mind that sending SMS reports is charged according to used prepaid or post paid program of respective GSM network operator 2 4 Switching ON the heater by phone call When checkboxes No 19 Phone activate and No 20 Heater start by phone call are both activated incoming phone call is indicated by flashing LED of ON OFF push button and by ringing tone in the speaker if connected and the phone call will be handled as follows a incoming phone call can be Accepted or Rejected within 10 seconds by pressing ON OFF push button b if incoming phone call is not Accepted or Rejected within 10 seconds by pressing ON OFF push button system evaluates such phone call as request to switch ON the heater the heate
31. hlas banner CommandCall SAF Professional ig Start tvs S My Computer Device Manager Note in used example you can see that on respective computer COM9 is designated to USB Programming Adapter For each single installation another COM port can be designated to USB Programming Adapter but if the installation is not changed CommandCall USB Programming Adapter will be designated to the same COM port even when inserted to another USB on the computer Designated COM port depends on computer configuration and it is possible to find designated COM port by checking one by one from the list or to find designated COM port directly by following procedure Designated COM port for USB to COM port converter you can recognize by the text CP210x USB to UART Bridge Controller in name of the respective port in the list of available COM ports followed by the number of COM port CommandCall CC1 26 In the case your PC will recognize CommandCall USB Programming Adapter even without Installation of program CP210x_VCP_Win2K_XP_S2K3 exe it is possible the text in name of relevant COM port will be different but it should be indicated that the port is allocated for USB to COM port converter In the case COM port designated for USB to UART converter has the number higher than COM9 for example COM15 it is suggested to change assignment of free COM ports by this procedure rao bint Mg ay Computer Mpy Smaa etch bes PrOteSS OUcumaE i e P wi P Search
32. i COM ports J High 14 14 Lote J High 16 16 COM19 COM20 in uscd COM21 in use COM22 Select lower Select higher Receive Buffer Transmit Buffer ee _ d E B ol Rhinoceros rozhlas banner CommandCall S to do paintball Pa My Computer g Device Manager 1e Adobe Photoshop CommandCall CC1 27 13 2 CommandCall PC Setup Installation Run Setup exe which is included on Installation CD ROM together with other SW tools of CommandCall GSM communication module Confirm the start of installation by pressing OK CommandCall PC Setup Setup P J Tostart CommandCall PC Setup Setup click OK To quit without installing dick Cancel OK Storno During the Installation follow instructions of installer program MYIDOCUTen AA i protestara MENO E My Computer ff d Internet Ex p lorer Rhinoceros Press the Next button on Welcome screen Installation folder input D W MyIDOCUM Ents E Br otesstObal BAGI Recycle Bin A d Internet Explorer CyberLink DYD ERB Suite Goog ent Mozilla Firefox l ddress rozhlas banner CommandCall I S P Search E Folders z File and Folder Tasks mj Rename this file Gy Move this file A Copy this file a Publish this file to the Web E mail this file XK Delete this file Other Places Desktop My Documents Shared Documents ig My Comp
33. ingly After appropriate port is selected you can finish COM ports assignment by accepting selections ig My Computer D we PTVADOCUNIE DUS mec BE aiy prinresstonaEL wy 7 wi A Search E Folders Ez CP x USB to UAR ridge Controller COM3 Propert R Address my Computer i we Port Settings Diver Details Ed ae aaam O Local Disk C System Tasks Bits per second 3600 7 EJ View system information beet ee My Network slouniie TH Add or remove programs _ Data bits 8 Xij Egi ee a Chan i gP vata E i ge a setting ui g gt S Parity None vi Stop bits 1 v cesi Fie Action View Help S ___ SS Flow control None S maS eA rag COME in use 38 Imaging devices COM in use _ Se Keyboards Q Restore Defaults Mice and other pointing devices x Bo Modems COM10 in use a COM11 in use COM12 in use 2 Monitors BB Network adapters 4 Other devices i Ethernet Controller Modem Device on High Definition Ports COM amp LPT aF BT Port COM10 aF BT Port COM11 a BT Port COM12 aF BT Port COM13 aF BT Port COM14 aF BT Port COM20 a BT Port COM21 a BT Port COM40 BT Port COM6 a BT Port COM a CP210x USB to UART Bridge Con compatible UART lect one of prnnec ems diplamayvy itable free i
34. ings This part is used for change of password and for enabling disabling usage of the user password Default returns user password value back to factory preset value 1234 Default does not change PIN code of the SIM card inserted into CommandCall control unit Change password opens input fields for new password and its reconfirmation Password disable allows user to send SMS commands without user password when this checkbox is activated system will execute received command without password validity check 9 2 Phone numbers for sending SMS Phone numbers for sending SMS Phone 1 4497907971170 Phone 2 Phone 3 Phone 4 This section enables to store phone numbers to be used for sending SMS reports Up to 4 phone numbers can be stored Phone numbers can contain country phone access code After Alarm is triggered CommandCall will dial the first phone number keeps ringing for 15 seconds to indicate violation of protected area and after that sends SMS No 14 Alarm trigger to all stored phone numbers and if checkbox No 22 is activated system enables automatically monitoring for 10 minutes When SOS function was activated CommandCall will dial the fourth phone number keeps ringing for 15 seconds to indicate emergency situation and after that sends SMS No 15 S O S to all stored phone numbers and if checkbox No 23 is activated system enables automatically monitoring for 10 minutes In the case phone number 4
35. installed and start of the installation Silicon Laboratories CP2710x VCP Drivers for Windows 7000 XP 7003 Ser x Choose Destination Location Select folder where setup will install files Install Silicon Laboratones CP210 WCF Orivers for Windows c SiLabs MCU InstallShield Silicon Laboratories CP210x VCP Drivers for Windows 2000 XP 2003 Ser Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation IF you want to review or change any of your installation settings click Back Click Cancel to exit the wizard InetalShield M ee f accept the location where the program will be installed and accept computer restart Silicon Laboratories Silicon Laboratories CP210x USB to UART Bridge 5 Installation Location Driver Version 4 40 C Program Files Silabs MCU CP210x Change Install Location Install Cancel Installshield Cancel CommandCall CC1 x VCP Drivers for Windows 2000 XP 2003 Ser Setup Status raj ety on street p yacon Laboratories LP41TUx USD to UART Bridge Drive all Ke mm a a Silicon Laboratories System Settings Change You must restart your computer before the new settings will take effect g j Do you want to restart your computer nowt Mo Qe ed Seg Cancel 25 g accept final Installation step of the CP210x_VCP_Win2K_XP_S2K3 exe
36. is blank system will send respective SMS immediately 9 3 SMS settings Every single SMS where it is reasonable to enable disable separately option of its sending has a checkbox for activating SMS sending when the checkbox is marked M in PC Setup Sent SMS reports can contain characters of English alphabet and numbers no local characters are supported and the maximum length of a message is 30 characters When the checkbox No 19 Phone activate is activated it is possible to make a phone call on built in phone in CommandCall control unit Incoming phone call is indicated by LED flashing LED of ON OFF push button and by ring sound in the speaker if connected If this checkbox is not activated it is possible to call on CommandCall only in the 10 minutes monitoring enabled period SMS reports confirming receipt and executing of the SMS command controlling the heater are sent to the phone number from which was the command sent SMS commands sent from free SMS gates of internet providers may be in some cases ignored SMS commands starting with text information are intentionally ignored because the format of SMS command is fixed and all SMS commands must start with number Each text field of SMS report in CommandCall PC Setup must contain at least one character otherwise PC Setup will give error message to the user SMS detail is null and the PC Setup settings as showed on the PC Setup screen can not be written to the
37. is user password the system will switch OFF the heater and will send respective SMS report Temperature is shown only if checkbox No 32 is activated If the heater was switched ON by external clock this command will have no effect 7 Switch OFF the heater by ON OFF push button If the heater was switched ON by SMS command or by push Eberspaecher OFF by button button the system will switch OFF the heater and will send ttt t C respective SMS report Temperature is shown only if checkbox No 32 is activated If the heater was switched ON by external clock this command will have no effect Switch OFF the heater by heater external clock If the heater was switched ON by external clock it can be Eberspaecher OFF by clock switched OFF only by external clock Temperature is shown ttt t C only if checkbox No 32 is activated 001 Switch ON the heater by SMS command for preset time in Receiving SMS command in form xxxx001 xxxx is user Eberspaecher ON by phone range 1 to 120 minutes password will switch ON the heater for o time and MMM min ttt t C For preset value 999 the heater will be switched ON for when preset time expires the heater will be switched OFF unlimited time Preset time can be set in PC Setup or by After starting the heater system will send SMS No 4 SMS command 281 Remaining time and temperature is shown only if respective checkboxes No 31 and 32 are activated Switch ON the heater by ON OFF p
38. ll PC Setup By typing wrong PIN code of SIM card in the CommandCall PC Setup programme the SIM card will be blocked system tries to register to GSM network repeatedly and will use all 3 allowed attempts to give correct PIN code of the SIM card It is possible to use SIM card with disabled function of validating PIN code In such case SIM PIN code stored in CommandCall control unit is ignored esa During CommandCall PC Setup installation new icon is created on the Desktop of your computer By Sr left mouse button double click on this icon you can start CommandCall PC Setup programme aE di CommandCall PC Setup is possible to start also from START menu of your computer through PROGRAMMS submenu CommandCall PC Setup is stored in MOLPIR folder Close all applications before using USB Programming Adapter then insert CommandCall Programming Adapter into any free USB port of your PC and then insert 10 PIN connector into CommandCall control unit When CommandCall PC Setup starts select assigned COM port from the list and then select on of three available languages English Slovak German and within 30 seconds press OK to enter the programme Identification of assigned COM port is described in Chapter 13 of this manual COM Port COMI Language ENGLISH nr PC setup Version 1 4 for Win 9x NT 2000 XP T Two way communication GSM module MOLP A ma TIR n Press esc key to cancel W
39. lomov seminar ay BT Port COM12 F BT Port COM13 ay BT Port COM14 1 x F BT Port COM20 F BT Port COMZ1 w _ Peas to do paintball i Start s G we 1 Y P My Computer A Device Manager EN A R a m B 21 14 b if no one port among available COM ports is designed to USB Programming Adapter marked as UART Bridge Controller follow instructions given in Chapter 13 CommandCall CC1 15 9 CommandCall PC Setup Before using CommandCall PC Setup it is necessary to install CommandCall PC Setup programme on your PC Installation procedure of CommandCall PC Setup programme is described in details in the Chapter 13 Before CommandCall control unit programming start the control unit must be switched OFF from the power and backup battery must by cut OFF too see 5 7 When backup battery is switched OFF red LED will switch OFF too During the communication of CommandCall with PC Setup programme is CommandCall powered from USB port of your PC It is recommended to take OFF SIM card from the CommandCall control unit before starting its programming by CommandCall PC Setup Before installing new SIM card into CommandCall control unit set up SIM card PIN to 0000 the same as default of SIM PIN set during HW production In such case new CommandCall unit can be installed to the vehicle even without using PC Setup If you plan to use another SIM PIN code you must write this new PIN code into CommandCall by CommandCa
40. memory of CommandCall control unit CommandCall CC1 18 9 4 Variables range allowed input values Periodical connectivity test can accept following values PTD 0 to 99 days PTH 0 to 24 hours PTM O to 60 minutes only positive numbers are accepted UST limit temperature value 40 0 to 125 0 C as a decimal part separator is used TS Temperature Stabile 0 to 999 seconds positive numbers only UST1 and UST2 the same values range as UST in addition UST1 gt UST2 TS1 the same values range as for TS HTP 1 to 120 minutes only whole positive numbers 999 switch ON for unlimited period time 9 5 Set values processing Request Apply Initialize Save Load Exit Request reads out the memory of the CommandCall control unit and displays the values on the screen Apply writes PC setup screen actual values into CommandCall control unit memory Initialize loads factory default values to PC Setup screen and to CommandCall control unit memory Save writes PC Setup screen actual values into file stored in your PC system will request user to specify file name and location By this means it is possible to have stored several standard configurations of parameters and SMS texts or archives of specific installations customer settings stored during unit installation Load reads parameters setting from file stored in your PC onto CommandCall PC Setup screen system will request user to specify file nam
41. ng tone or LED flashing and user can listen to the sounds in the vehicle User password change Receiving SMS command in form xxxx284MMM xxxx is user password will change the user password from xxxx to NNNN Command in form xxxx284 xxxx is user password ook ooh gt lt 281 MMM min OK Monitoring enabled Password change OK Password disable OK will disable using of user password Command in form 284NNNN will restore using of user password and will set its new value NNNN Change of phone number 1 Receiving SMS command in form xxxx285MMM xxxx is 285 OK user password will set the first phone number for sending SMS reports NNN is country code T T is phone number Command xxxx285 will erase the first phone number Change of phone number 2 Receiving SMS command in form xxxx286MMM xxxx is 286 OK user password will set the second phone number for sending SMS reports NNN is country code TT T is phone number Command xxxx286 will erase the second phone number Change of phone number 3 Receiving SMS command in form xxxx287MMM xxxx is 287 OK user password will set the third phone number for sending SMS reports NNN is country code TT T is phone number Command xxxx287 will erase the third phone number Password change OK fix fix t N CommandCall CC1 7 Command Description Text of SMS report Check SMS box report Command code 2
42. nto Close all applications before using USB Programming Adapter then insert CommandCall CommandCall control unit In case your PC does not recognize automatically CommandCall USB Programming Adapter after its inserting into USB port of your PC follow instructions described for USB port to COM port converter Program CP210x_VCP_Win2K_XP_S2K93 exe is supplied on Installation CD ROM together with other SW tools of GSM communication module CommandCall During installation follow instructions given by installer program When the installation of USB to COM port converter is finished CommandCall USB Programming Adapter is ready for use Check if your PC recognized USB Programming Adapter by using following procedure a insert USB Programming Adapter to any free USB port on your PC run Device Manager on your PC and check available COM ports by executing sequence of highlighted commands in defined order first double click on left mouse button on My Computer icon to open pop up window My Computer then click with left mouse button on View system information in section System Tasks then click on Hardware etc GA My Computer renden wi Ka Search i Folders EK J Address p My Computer System Properties Cad ud na aoan a 2 System Tasks ANE Local System Restore Automatic Uodate Remote j Canal Computer Na Hardware dvanced IZ Vi
43. oming phone Call eee eeceeceecccceeceeeeeeeeeeeeeeeeeeeeeesaeeeeeaaeeeeeaes 12 5 10 Exceeded temperature limits ha ecccenccecenseeeceesecceuneecsuucecceuseeeseuseeseseessuseeesseeessaes 12 Sli Speaker VOIM ate neice tte ecient a 13 Bale MOM CCUM ta a l A 13 5 13 CommandCall status LED InNdicatioNS _eeeeeeeeccccceecccecceeeeeeeeeeeeeeecaaeeeeeesueeeeeseeaeeeeesaeeeeeeeas 13 5 14 Periodical connectivity test __hadeccccaceecaneeeccaueecccuececceuceccauseeceeeeessueeeesuaseeseaeeessans 13 6 ON OFF DUS DUIIONTUMCTIONS devedienenidonetaisanchiccieuenieie ecedeneb ne decenesteaGeead 14 7 CommandCall USB Programming Adapter ceeeccccccccssecceceueeeceeeaeeeceeeaeeeeeeeaeeeeeseaeeeeeseaeeeeeseaees 15 8 WSBIOGOM On GOnVEersion j Aan N dees 15 9g CommandGalPG Setup le iit te cpa tinct eects Sha aracs nants ube leanee anand eueiiunsausetentuees 16 OTe PassWord Seting ieee cctel cece a rate mma EE ea 18 9 2 Phone numbers for sending SMS reports _a see ceeeccccseeeccceeeeeceececceusececeucecseneeesseeeeseneeesseeenss 18 93s SMSen S jj e e a ue keuiesenosianen 18 OA VANeaDIGSTaNGe 4 bik suheh uletc huteeteceaceiuet eile aut teteialee eleteen abut ete ceaten 19 O5 SCrVaIGES DIOCESSING hiker cach oe ec Atl al eel ate Madea cea al 19 10 Installations instructions hss tute sine hres ddudiedcua tewtkeuascieacnedinneetancaluncedtessscuceds 20 TUeIFOUBIGSMOOUNG ei rill eae crete hci uhde ati eucen a
44. ormed accordingly 2 1 The way of communication The user communicates with in the car installed unit via sending and receiving SMS or by making phone call The format of sent commands is described in the table Control commands Chapter 3 Format of the commands is fixed the format text of SMS reports which CommandCall sends to the user may be set during the unit installation All parameters except PIN code of SIM card may be changed set during standard operation by specific SMS command 2 2 The format of SMS command The format of SMS commands has fixed syntax password command code command parameter while password consist of 4 digits command code consist of one to three digits command parameter is specific for each command and can contain phone number time information requested temperature value CommandCall CC1 3 For commands code with leading zero s may be used in short version e g with leading zero s omitted For example the command 003 can be used in short version as 3 In between the password command code and command parameter no separator is used comma space User password is factory set to the value 1234 By setting checkbox Password disable in CommandCall PC Setup it is possible to disable using user password in the system and then all SMS commands starts directly with the command code in such case the password is not used at all User password i
45. ory devices removal CommandCall CC1 24 d run CP210x_VCP_Win2K_XP_S2K3 exe program from included Installation CD and accept licence agreement Silicon Laboratories CP2710x VCP Drivers for Windows 7000 XP 27003 Ser Welcome to the InstallShield Wizard for Silicon Laboratories CP210x CP Drivers for Windows 2000 4P 2003 Server Vista The InstallShield Wizard wall install Silicon Laboratories CP210 YCF Drivers for Windows 2000 4P 2003 Server vista an Your computer To continue click Next Silicon Laboratories CP210x VCP Drivers for Windows 7000 P 7003 Ser X License Agreement Please read the following license agreement carefully END USER LICENSE AGREEMENT IMPORTANT READ CAREFULLY BEFORE AGREEING TO TERMS THIS PRODUCT CONTAINS CERTAIN COMPUTER PROGRAMS AND OTHER THIRD PARTY PROPRIETARY MATERIAL LICENSED PRODUCT THE USE OF WHICH IS SUBJECT TO THIS END USER LICENSE AGREEMENT INDICATING YOUR AGREEMENT CONSTITUTES YOUR AND IF APPLICABLE YOUR COMPANY S ASSENT TO AND ACCEPTANCE OF THIS END USER LICENSE AGREEMENT THE LICENSE OR AGREEMENT IF YOU DO NOT AGREE WITH ALL OF THE TERMS YOU MUST NOT USE THIS PRODUCT WRITTEN APPROVAL IS NOT A PREREQUISITE TO THE VALIDITY OR e Sree amne mT ee Se eee eee ar rr a ee ee ea accept the terms of the license agreement do not accept the termes of the license agreement Installshield e accept the location where Windows drivers will be
46. port No 35 Short circuit to the first phone number stored After short circuit disappears the system will recover automatically and restores standard operation automatically In the case the system will not start normal operation within 10 minutes RESET the system please follow instruction 5 6 5 13 CommandCall status LED indications CommandCall control unit is equipped with 2 LED indicating current operation status of the unit Meaning of indication status is described in following table Red LED Green LED Status of control unit flashes 2 seconds interval standard operation everything OK flashes 1 seconds interval GSM module tries to register to the GSM network Power voltage too low for normal operation After Power cut the red LED is still ON and CommandCall sends to stored phone numbers SMS report No 16 Power cut 3 minutes later the system will send the same SMS report again and will cut OFF built in backup battery and will switch OFF red indication LED in this moment CommandCall CC1 is switched OFF It is possible to cut OFF backup battery manually follow instructions 5 7 before the second SMS report is sent 5 14 Periodical connectivity test Functionality Periodical connectivity test enables to set up automated process of sending SMS report to the user the first phone number stored in preset time intervals which shows operability of CommandCall for example system will send SMS report No
47. program r x InstallShield Wizard Complete The InstallShield Wizard has successtully installed Silicon Laboratories CP210 YCF Drivers for Windows 2000P 2003 Serverf ista Click Finish ta exit the wizard Back Finish Cancel h run Device Manager on your PC to check results of USB to COM port converter installations and check designated COM port number te nine iy Computer Sela NVIDOCUMEn CS MACS ccc E PTOESSIOUSUmEEL gt wi P Search Key Folders E i on PY My Computer nd 2 System Tasks Q System Restore ybacsake ipreerhia Remote i view system information General Compute 3 Advanced My Network slovnik t SUU O oe programs System Properties Device Manager tats all the hardware devices installed E BX e Device Manager to change the LECH Ee File Action View Help i Device Manager x evice Manager es a R 4 IDE ATA ATAPI controllers Gap IEEE 1394 Bus host controllers ake sure that installed drivers are Imaging devices s Windows Update lets you set up gt Keyboards to Windows Update for drivers Mice and other pointing devices gt be em id Monitors BB Network adapters pe Other device e a way for you to set up and store Ports COM amp LPT urations F BT Port COLA F BT Port com BT Port COM13 a7 BT Port COM14 BT Port COM20 aF BT Port COM21 aF BT Port COM40 CONG Ad Aware SE Rhinoceros roz
48. r will be switched ON and phone call terminated If checkbox No 4 is activated SMS report No 4 Heater ON by phone is sent to calling phone 2 5 Alarm trigger After car alarm defence area was triggered the system starts after 3 seconds delay the car horn interrupted sound and CommandCall will dial the first preset phone number After 15 seconds ringing system will terminate the phone call and will send SMS No 14 Alarm trigger to all stored phone numbers max 4 numbers User can press Call terminate button on his mobile phone to hang up the phone and to receive short message immediately When vehicle ignition is switched ON ACC ON while the alarm is triggered the system will send SMS report No 17 ACC trigger to all stored phone numbers If the first phone number stored in CommandCall is blank the system will use next phone number Checkbox and SMS report listed in following table of control commands are links to relevant checkboxes and text of SMS report related to specific command or system function Checkboxes and SMS report texts are accessible through CommandCall PC Setup CommandCall CC1 4 3 Control commands Command Description Text of SMS report Check SMS box report Command code Switch OFF the heater by SMS command If the heater was switched ON by SMS command or by push Eberspaecher OFF by SMS button prior receipt of SMS command in form xxxx000 xxxx ttt t C
49. re harness 0 0999017 1 2 General description GSM communication module CommandCall is used for transfer of control commands and reports between the user and the vehicle via SMS of GSM network Unit transfers information gained from built in vehicle alarm enables control and monitoring of the status of independent heater in vehicle via SMS commands and reports measuring actual in car temperature monitoring of in car activities via phone call with the vehicle for example when car alarm is triggered and to switch ON the heater by phone call Integrated part of the CommandCall is built in GSM module phone supporting SIM 3V cards of any GSM mobile operator at 900 amp 1800 MHz In the system may be used any post paid or prepaid SIM card In the case of using prepaid SIM card it is important to watch SIM card validity expiration and keeping necessary credit available on the card to be sure the system is ready to send SMS report to the user when needed Some mobile operators offer the feature of automatic maintenance of minimal credit GSM communication module CommandCall CC1 can be used in any type of vehicle due to its voltage auto sensing feature auto sensing 12 24V CommandCall is not an ALARM it is GSM communication module used for transfer of commands and reports for independent heater control in the vehicle CommandCall can be connected to built in car alarm and then alarm signals can be taken in consideration and the user can be inf
50. s possible to change any time by using SMS command 284 or in PC Setup Execution and confirmation of individual command can be delayed depending on actual traffic in used GSM network 2 3 Content of SMS report The content of SMS reports text of SMS reports sent to the user is factory preset but it is possible to change it during system installation by using CommandCall PC Setup Reports texts can be in local language SMS reports can contain the characters of English alphabet does not contain local characters Format of reports sent by the system to the user which contain beside the text also parameter value is not possible to modify by the user fix type report SMS reports sent by CommandCall to the user can be separated into 2 categories e reports sent by the system to the user based on specific event CommandCall sends the report to the user after processing specific event pressing switching the heater ON or OFF by external clock the signal received from the built in alarm periodical test timeout Up to 4 phone numbers can be stored in CommandCall memory used for automated sending SMS reports The first phone number for sending SMS reports is used for sending standard reports emergency reports are sent always to all stored phone numbers as emergency reports are considered alarm trigger report ignition ON after alarm trigger Power cut and S O S e answer to user request CommandCall sends report to t
51. ss seconds OK 18 fix exceed UST1 or UST2 value to be recognized as limit level password will set TS1 to sss value sss is time value in break for exclusion of short term temperature change seal range 0 to 999 seconds CommandCall CC1 9 Command Description Text of SMS report Check SMS box report The checkbox No 27 Entering the interval from top Activating the checkbox No 27 will enable sending SMS Temp decreased into interval 2 7 No 27 in the case actual temperature decreases under UST1 and stay bellow UST1 longer than specified time TS1 The checkbox No 28 Entering the interval from bottom Activating the checkbox No 28 will enable sending SMS Temp increased into interval No 28 in the case actual temperature increases over UST2 and stay over UST2 longer than specified time TS1 Command The checkbox No 29 Leaving the interval down Activating the checkbox No 29 will enable sending SMS Temp left interval down 29 No 29 in the case actual temperature decreases under UST2 and stay bellow UST2 longer than specified time TS1 The checkbox No 30 Leaving the interval up Activating the checkbox No 30 will enable sending SMS Temp left interval up 30 No 30 in the case actual temperature increases over UST1 and stay over UST1 longer than specified time TS1 8 8 O O Q D E NO NO O O 00 325 Setting number of days for Periodical connectivity test PTD Receiving
52. the format suitable to be sent as command 290 CommandCall CC1 10 4 Basic commands overview As a help for the user to control independent heater by SMS commands this card shows an overview of mostly used commands for the heater control in form of credit card which can be permanently present in user s wallet Z DIESA CommandCall ZEIT CommandCall Independent heater control 7 Selected functions controlled ma a through SMS commands mea ial through SMS commands Code Command Code Command Switch OFF the heater 5 Panic Switch ON the heater for preset time 6 Car engine blocking Actual status of the heater 7 Emergency release of car engine blocking Remaining heating time and actual temperature 281 Timer preset value change 1 120 minutes 0 Switch ON the heater for 10 minutes 282 Monitoring enable for 10 minutes Switch ON the heater for 120 minutes SMS format xxxxNNWN xxxx is user password NNN is command code SMS format xxxxNNN xxxx is user password NNN is command code front side reverse side 5 Supplementary functions 5 1 Panic The user can start the horn of the vehicle intermittent sound 30 seconds by using SMS command 005 5 2 Anti car jacking car engine blocking This is extending functionality of CommandCall enabling blocking of vehicle fuel pump and thus disabling its further movement The activity leading to fuel pump disabling depends on actual status of ignition ACC method which conforms with EC r
53. ting with text received SMS format SMS sent by the operator advertisement or service SMS messages sent from free or paid GSM gates and answers only to the phone number from which respective SMS was sent system does not send checkbox No 21 is not activate checkbox No 21 SMS of periodical test activated system sends string temperature sensor is not check connection and functionality of temperature sensor instead of connected or is damaged temperature value CommandCall CC1 21 12 Wiring diagram 12 1 Wiring diagram of CommandCall CC1 with independent heater Wires side view GSM LED green a na fh Power LED red microphone s fs 1 CH1 yellow 2 1 S K 2 505 blue 2 HORN 3 GND brown eey 3 HORN 4 LED red yellow 4 ARM 5 12 24 red 1 5 ARM 6 GND brown 3 6 ACC 7 GND brown EnEn 7 5V i lt SY 8 TEMP white ai is 8 GND USB Programing M A a E a a i a A TT 9 TX Adapter 10 RX i a GSM antenna connector power supply 12 24V channel output 300mA GND chasis 0 5 yellow 0 5 brown ON OFF push button with orange LED E m H H Temperature sensor External clock CommandCall CC1 22 12 2 Wiring diagram CommandCall CC1 with independent heater and accessories Wires side view 6 7 8 L9 10 GSM LED green Power LED red microphone fs S F speaker _ gay option a 5j 1 CH1
54. tion 21 5 2007 14 46 mj Rename this file tm S E f gp100_my9 enc 73KB ENC File 20 9 2007 6 45 aerate i Setup 4981 KB Windows Installer P 24 9 2007 8 40 A Copy this file Publish this file to the i CommandCall PC Setup Web G E mail this file Confirm Installation ii X Delete this file Recycle Bin Other Places The installer is ready to install CommandCall PC Setup on your computer Desktop Click Next to start the installation My Documents Shared Documents a 4 My Computer f a My Network Places ASUS IC Q 6 Goo g Net4Switch Internet CyberLink DYD ERB Explorer Suite Details 7 z Setup Atheros Client Mozilla Firefox Windows Installer Package Utility Date Modified 24 septembra 2007 8 40 Size 4 66 MB Spybot vizualizacie Searc C E E al Rhinoceros rozhlas banner 14 2 B CommandCall SAF creas to do paintball E Y Adobe Photoshop Removable Disk f Commandcall jie GSM_GPS PC SE EN R amp ma 5 1 36 MyIDOCUMEn to mEAC sy stC LT cs ErotesslOUclmb OL v Es Name Size Date Modified File and Folder Tasks E boot loader Setup 3554KB Windows Installer P 24 5 2007 14 40 a Ft CP210x_ CP_Win2K_XP_52K3 3124KB Application 21 5 2007 14 46 G Make a new folder i l gp100_myv9 enc 73KB ENC File 20 9 2007 6 45 ad U Publish this Folder to the j5 setup 4981 KB Windows Installer P 24 9 2007 8 40 My Network asm an Web Places Kad Share this folder ig CommandCall PC S
55. ush button for preset Pressing ON OFF push button will switch ON the heater for Eberspaecher ON by button time in range 1 to 120 minutes preset time and when preset time expires the heater will be MMM min ttt t C unlimited time Remaining time and temperature is shown only if respective For preset value 999 the heater will be switched ON for switched OFF After starting the heater SMS No 5 is sent checkboxes No 31 and 32 are activated Switch ON the heater by external clock Heater will be switched ON by external clock and will stay Eberspaecher ON by clock ON depending on external clock setting ttt t C After starting the heater system will send SMS No 6 Temperature is shown only if checkbox No 32 is activated request for heater status Possible states are After receiving SMS command in form xxxx002 xxxx is Heater OFF user password system will respond to the user by sending Eberspaecher OFF ttt t C 33 Heater ON by SMS or by phone call respective SMS report depending on current state of the Eberspaecher ON by phone 4 heater MMM min ttt t C Heater ON by ON OFF push button Remaining time and temperature is shown only if respective Eberspaecher ON by button 5 checkboxes No 31 and 32 are activated MMM min ttt t C Heater ON by external clock berspaecher ON by clock 6 ttt t C CommandCall CC1 5 Command code 003 Remaining heating time and actu
56. uter a My Network Places Details Setup Windows Installer Package Date Modified 24 septembra 2007 8 40 Size 4 86 MB Adobe Photoshop CommandCall Name CommandCall IO C Documents and Settings Administrator Desktop CommandCall Date Modified 24 5 2007 14 40 21 5 2007 14 46 20 9 2007 6 45 24 9 2007 8 40 Size Type 3554 KB 3 124 KB 73 KB 4 981 KB j5 boot loader Setup 2 CP210x_ CP_Win2K_XP_S2K3 E gp100_myv9 enc j5 Setup i CommandCall PC Setup Windows Installer P Application ENC File Windows Installer P Welcome to the CommandCall PC Setup Setup Wizard The installer will guide you through the steps required to install CommandCall PC Setup on your computer WARNING This computer program is protected by copyright law and international treaties Unauthorized duplication or distribution of this program or any portion of it may result in severe civil or criminal penalties and will be prosecuted to the maximum extent possible under the law to do Removable Disk fm CommandCall ji GSM_GPS PC SE EN A 3 E Bo iii paintball pi Search E Folders E O C Documents and Settings Administrator Desktop CommandCall File and Folder Tasks fw Rename this file E Move this file Copy this file a Publish this file to the Web tm E mail this File XK Delete this file Other Places Desktop E My Documents Shared Documents ig My Comp
57. uter a My Network Places Details Setup Windows Installer Package Date Modified 24 septembra 2007 8 40 Size 4 86 MB vizualizacie ae rozhlas banner CommandCall CC1 I Adobe Photoshop Name Date Modified 24 5 2007 14 40 21 5 2007 14 46 20 9 2007 6 45 24 9 2007 8 40 Size 3 554 KB 3124 KB 73 KB 4 981 KB Type Windows Installer P Application ENC File Windows Installer P j5 boot loader Setup 2 CP210x_ CP_Win2K_XP_S2K3 E gpi00_myv9 enc i Setup 1 CommandCall PC Setup Select Installation Folder The installer will install CommandCall PC Setup to the following folder To install in this folder click Next To install to a different folder enter it below or click Browse Folder C Program Files CommandCall CommandCall PC Setup Install CommandCall PC Setup for yourself or for anyone who uses this computer Everyone Just me CommandCall Removable Disk CommandCall fe GSM_GPS PC SE JB LIB 21 33 of CommandCall PC Setup installer program to proceed to paintball B Ep After accepting or specifying location where the program will be installed press Next again to proceed MYIDOCUTMEn ARN i EFOceSslOtcl meno Name Size Type Date Modified File and Folder Tasks Bl boot loader Setup 3554KB Windows Installer P 24 5 2007 14 40 ra as f2 CP210x_ CP_Win2K_XP_S2K3 3124KB Applica
58. xample by the drivers or passenger knee Drill 10 mm hole for installation maximal wall thickness is 2 5 mm Insert the cable through the hole lead it to the control unit and connect contact PINs in respective connector according to wiring diagram Temperature sensor T1 install in proper place in the level of drivers face for example onto front chassis column Lead temperature sensor cable lead to the control unit and connect contact PINs in respective connector according to wiring diagram Temperature sensor is used for in car temperature measurement Microphone install on proper place for example onto front chassis column Lead microphone cable to the control unit and connect its jack connector in respective plug Microphone is used for monitoring the car sounds and when optional speaker is installed two way voice communication is possible Speaker optional accessories install on proper place Lead the speaker cable to the control unit and connect its connector to respective plug When the speaker is used two way voice communication is possible Wire harness for connecting independent heater has 3 wires permanent power supply and heater control signal terminated with contacts Wires with terminals insert in included 6 PIN connector body according to wiring diagram Use wires marked and the remaining wires must be isolated separately Accessories wire harness of car alarm car engine blocking relay disconnecting relay of fuel pump
59. y incoming phone call to CommandCall will be automatically accepted and built in microphone is switched ON The user can monitor the sounds in the vehicle During the monitoring call the LED in ON OFF push button is disabled no indications of ringing or active phone call and the passengers can not use ON OFF push button to reject or terminate monitoring phone call 5 5 Monitoring For security reasons it is possible in specific cases to make monitoring call and to listen to the sounds in the vehicle Monitoring call is accepted automatically without any LED or sound indication of incoming phone call Monitoring call is enabled in following cases alarm trigger occurs and checkbox No 22 is activated SOS function activated by passengers in the vehicle and checkbox No 23 is activated Blocking function activated and checkbox No 24 is activated After activation of some of these functions system allows user to make phone call to the built in phone in CommandCall within 10 minutes period Phone call is accepted automatically and the user can monitor the sounds in the vehicle for unlimited period After 10 minutes passes the possibility for monitoring phone call is deactivated the user can anytime enable monitoring call for 10 minutes by command 282 After 10 minutes the possibility for monitoring phone call is deactivated CommandCall CC1 11 Incoming phone call to built in phone in CommandCall except enabled
60. yelow 1 SK grey i 2 505 blue 2 HORN green brown 3 GND brown erei 3 HORN green red J a 4 LED red yellow 9 4 ARM black brown CommandCall 5 12 24 red 5 ARM black red j 6 GND brown 6 ACC red white 7 GND brown J temp sensor 7 V O SJ 8 TEMP white P 8 GND USB Programing annn Annno fo 9 TX Adapter T i 10 RX power supply 12 24V channel output 300mA GND chasis yellow brown 0 5 yellow 0 5 brown ON OFF push button with orange LED OU External clock Temperature sensor CommandCall CC1 GSM antenna connector red white black red signal ignition ACC Alarm signal black brown Alarm signal green red Horn output green brown Horn output 30 85 8 amp 6 87 grey 300 mA output to blocking relay 12 24V ACC blocked circuit 23 13 SW Installations 13 1 USB to COM port conversion Connection of your PC with CommandCall control unit for modification and setting parameters and sent SMS contents texts is realised via USB port connection It is serial communication and it is necessary your PC will recognize inserted CommandCall USB Programming Adapter as serial port This is executed by operation system functions Win9x NT 2000 XP or by using specific driver program CP210x_VCP_Win2K_XP_S2K3 exe Programming Adapter into any free USB port of your PC and then insert 10 PIN connector i

CommandCall CC1

Contents

Download Pdf Manuals

Related Search

Related Contents