Instruction Manual for Serial Interface Software
Contents
1. Transmitter Interface Program Operational Manual gt Version 3 0 4 Max Machinery Inc an ISO 9001 2008 certified company Overview The transmitter interface software allows you to adjust configuration settings of your Max solid state transmitters The following settings can be accessed and modified Pulse Output Scaling Analog Output Limits and Scaling Signal Filtering Options and Compensation settings To use the serial interface an interface kit can be purchased from the factory Max Part 294 100 050 This includes the installation CD and a special cable to connect the transmitter to the USB or serial port of a PC Software Installation Procedure This program is built off of Labview s runtime library It is designed only for Windows 2000 Windows XP Vista or Windows 7 Also a minimum of 128 MB of RAM at least 100 MB of available disk space and a screen resolution of at least 800 x 600 pixels is required While it is acceptable to have multiple versions of the runtime library and the Max Transmitter program installed on the same computer it is preferred that old versions be removed before installing the latest revision To remove the old versions Click on Start Settings then Control Panel Double Click Add or Remove Programs Find either Max294 or MaxXmtr and click on it Click on Remove and follow the on screen instructions To remove the National Instruments runtime components select Nationa2. This feature corrects for mechanical non linearity of the meter to produce an output signal that is precisely proportional to flow Typically the only reason to turn off linearization is to collect the calibration data with which to populate the linearization table on the factory data tab Note on analog transmitters this feature cannot be disabled Pulse Output With linearization enabled the meter s output can be set to a precise Output K Factor where each pulse represents a fixed volume This allows the user to take several meters and set them all to an exact scaling With Linearization off you are able to set a fixed number of pulses per revolution of the meter Note for quadrature output transmitters the Output K Factor shown is the output on one of the channels phase A OR phase B however the meter s total resolution is the total number of pulses output on both channels phase A PLUS phase B SE M 001 Version 3 0 4 VERSION FLOW UNITS CC s JLITERS LINEARIZATION FLOW REVERSAL DEADBAND 50 of 1 Rev SIGNAL DAMPENING 8 METER FLOW DIRECTION Ocwpos Occwpos GAl postive VERSION FLOW UNITS E CS JUTERS LINEARIZATION CJOFF ON FLOW REVERSAL DEADBAND 50 of 1 Rev SIGNAL DAMPENING 83 OUTPUT DATA OUTPUT DATA FACTORYDATA PULSE OUTPUT OUTPUT RESOLUTION 1000 Pulses Rev OUTPUT K FACTOR 93 4810 Pulses cc ANALOG OUTPUT OUTPUT MIN OUTPUT MAX 15 0
3. 00 MA 15 000 MA FLOW MIN 10 000 ec min FLOW MAX 100 00 cefmin FLOW CALCULATOR DUTPUT 0 000 mA FLOW 0 00 cee min FACTORYDATA PULSE OUTPUT OUTPUT RESOLUTION 1000 Pulses Rey OUTPUT K FACTOR 93 4810 Pulses cc ANALOG OUTPUT OUTPUT MIN OUTPUT MAX 15 000 ma 15 000 mA FLOW MIN 10 000 cc min 100 00 Ce min FLOW MAX FLOW CALCULATOR OUTPUT 11 667 ma Max Machinery Inc an ISO 9001 2008 certified company Flow Units This field shows the units used for the Transmitter Output Settings as well as the Linearization Data stored on the transmitter Analog Output This sets both the output limits and the output scaling Voltage transmitters can be set anywhere between 10V and 10V and current transmitters within the range of 20 mA to 20 mA Because the transmitter receives a 2 stage calibration at the factory it is possible to change the analog scaling at any time without loss of accuracy or need to re calibrate Note that the minimum and maximum output values are hard limits that the transmitter output will not exceed The Flow Minimum and Flow Maximum can be set to any desired measurement range both negative and positive the output span can even be set to a tight band such as 200 ccm minimum and 250 ccm maximum if you want very high resolution and have a specific flow range that you are measuring Flow Calculator This is simply a tool to allow the user to run sample values of either the flow r
4. acterizes the flow meter and sensors at a steady flow rate to provide optimal spacing of the output pulses Use when optimal output response is needed Factory Compensation is not available or the application is very low flow or high viscosity fluid Note You must have a steady flow during compensation SE M 001 Version 3 0 4 8 Max Machinery Inc an ISO 9001 2008 certified company Perform Factory The option is used only by the factory for initial compensation Requirements for Field Compensation Recommended Meter RPM 15 1000 Minimum Acceptable RPM 10 LOW FLOW error displayed if lower Maximum Acceptable RPM 1350 HIGH FLOW error displayed if higher Maximum Allowable Flow Ripple 3 or UNSTEADY FLOW error displayed Activating Selected Compensation After selecting the desired compensation option the Proceed with Option button must be pressed This initiates the compensation during which the Status Bar will turn yellow In Progress may take up to I minute Upon completion the Status Bar will turn grey and display the results of the compensation Linearization Data The displayed values are from the Raw Factory Calibration of a flow meter They are NOT the values shown on the Calibration Certificate provided with the flow meter Typically the linearization table is programmed into the transmitter meter assembly at the factory and will not need to be modified by the user except in the following cases a After per
5. added after measuring the signal The time constants and equivalent cut off frequency for each type of meter are as follows The default setting for all models is 5 Pulse Output chart pesem f e p ee e e neces foe a er fre we ao foes ws ao ranner roo em feo gt fer e eb Analog Output chart fees fo ppe se Pe recono foe ar re we as fees as eso so0 ise eotrewer iio en ro feo for se fe le eh Analog Output chart continued Cut off Frequency Hz 0 125 0 062 0 031 0 015 Read and Write to Transmitter These two buttons allow for reading from or writing to the transmitter After entering new data into any of the fields a Data Changed prompt will be displayed If you wish to save any entries or selections you have made you must download those new settings into the transmitter by pressing the Write to Transmitter button To discard changes you can select Read from Transmitter to again upload what is in the transmitter memory SE M 001 Version 3 0 4 7 Max Machinery Inc an ISO 9001 2008 certified company Factory Data Screen VERSION OUTPUTDATA FACTORY DATA The Factory Data tab shows calibration settings that generally will only need to be set at the factory Most fields are LINEARIZATION DATA Taken max resolution password protected If needed contact RARBG SONNE BE IBE CHSERWER HALSHRRE the factory for details cc min Pulses ce 10 0000 92 6950 Compensation Opt
6. ate or the output value After entering one field the alternate field is then calculated based on the chosen analog scaling Meter Flow Direction This field is set by the factory based on the mechanical design of each meter CCW counter clockwise CW clockwise If the meter is installed backwards for any reason this field can be switched to correct any sign reversal If bidirectional measurement is not needed this may be set to All Positive Flow Reversal Dead Band On meters without a bidirectional output there is a risk that momentary reverse flow will be output as if it was a positive flow To prevent this the transmitter can be programmed with up to 100 of 1 meter revolution to act as a dead band For instance if you select 50 any flow reversal that does not cause the meter to turn more than 1 2 of a revolution in the reverse direction will be buffered and only net forward flow will be counted If the meter turns more than the dead band amount in the reverse direction the meter will then begin reporting reverse flow For unidirectional configurations the default setting is 50 SE M 001 Version 3 0 4 6 i Max Machinery Inc an ISO 9001 2008 certified company Output Signal Dampening This feature sets the time constant cut off frequency used to filter the raw flow signal Selecting zero will turn off the filtering completely The zero setting can be useful if sudden flow changes need to be measured or if filtering will be
7. forming a field calibration of the flow meter b During a field replacement of the transmitter where the customer wishes to enter the linearization data In this case you must request the Raw Factory Calibration Report be sent to you for the flow meter the flow meter serial number is required or note the values entered into the original transmitter s linearization data fields The factory can also load K factor data into a replacement transmitter before shipment Analog Calibration This data is collected on analog transmitters using high accuracy measurement equipment and provides precise calibration of the onboard circuitry Note Do not make changes in this area A loss of cal and result data will shut off the analog output signal Contact Us If you need further assistance e mail info maxmachinery com or call 707 433 2662
8. ions Bid BEE Compensation is a software feature es where the transmitter measures the 93 4810 rotational speed of the meter thru one 1000 00 complete revolution and then corrects 3000 00 NO STATUS AVAILABLE for this variation Because different 7000 00 92 9600 mechanical meters contain design iocoa g FO 92 7440 BR nie a a ANALOG CALIBRATION differences resulting in cyclic speed T 0 00000 2 00000 x variation this process is able to smooth BETH eT 050 1 out this cyclic error without adding any nl nommen are signal filtering Note that it is critical that wen EET i i m ie CAL LO RESULT LO a constant flow is passing thru the meter xc er rhe Sa when this compensation is done so that m 0 000 mA 0 020 mA x ee f 0 00000 0 00000 only mechanical variation is mapped by ee CAL MID RESULT MID 5 0 00000 0 00000 the transmitter ie ss 5 000 mA 4 987 mA 0 00000 0 00000 CAL HI RESULT HI Restore Factory 10 000 ma 10 002 Unibir _ BiDir This option restores the compensation table to the values that were originally learned at the factory Generally used Password to Unlock Factory Fields SOON OFFSET after a field compensation yields poor results i CYC O GAIN Disable This turns off the cyclic compensation and is only recommended for a field replacement transmitter when a steady flow is not available to perform a field compensation Perform Field This option char
9. l Instruments Software Click on Remove and at the pop up window select Ni Visa Runtime and Remove SE M 001 Version 3 0 4 2 i Max Machinery Inc an ISO 9001 2008 certified company Now you can complete the following steps to install the latest version of this program 1 Disable any automatic virus detection programs and exit all applications before running this installer 2 Insert the MaxXmtr Serial Interface Program installation CD and follow the instructions on the screen 3 If your PC has the Auto Run feature disabled the SETUP EXE program can be started from either Windows Explorer or by the following sequence a Click on Start then click on Run b Select Browse Find the installation CD and double click Setup exe 4 After the installation is complete re enable any virus detection programs you may have disabled 5 Torun the Serial Interface Program press Start All Programs then find MaxXmtr MaxXmtr and click 6 If any problems occur reboot and follow the removal instructions above Then reboot and attempt the install again If the problem persists please contact Max Machinery Starting the Interface Program 1 Remove the lid of the transmitter to reveal 1 8 serial port See the transmitter s user manual for assistance 2 Next insert the 1 8 serial plug into the connector on the transmitter circuit board 3 Connect the serial cable to the serial port on the PC If your computer does not have any fo
10. ogram active and press lt Alt gt lt PrintScreen gt on the keyboard This will copy the current window to the clipboard which may then be pasted in to Microsoft Word or other document programs Program Compatibility The program is designed to work with all current and previous versions of the Max Model 269 and 290 Series transmitters After reading the data out of the transmitter the appropriate fields will be active and the other fields will be grayed out or hidden Additionally certain fields can only be changed by entering a factory password In limited cases mainly when doing a field replacement of a new transmitter on an old meter the factory fields may need to be accessed by the customer In these cases contact the factory or your local sales representative for details Interface Simulator Mode A simulation mode may be accessed by starting the program without any connection to a physical transmitter When prompted to select a serial port choose any unused port and when prompted by Transmitter Not Detected select Cancel Then select OK to run in simulator mode This allows you to tryout the functionality of both pulse and analog transmitters without needing to physically connect to a transmitter SE M 001 Version 3 0 4 4 Max Max Machinery Inc an ISO 9001 2008 certified company Output Data Screen The Output Data tab provides access to the most commonly adjusted parameters for the transmitter Linearization On Off
11. rm of serial port then the USB to serial adapter can be used To use the USB port you must first install the proper driver on your computer Please refer to the Readme file on the CD before using the USB adapter 4 Ensure the transmitter is powered up and launch the MaxXmtr Interface Program by either selecting MaxXmtr from the start menu or by double clicking on the MaxXmtr executable located in the installation directory A dialog box will prompt the user to select the serial port Choose the port to which you have connected the serial interface cable and press Continue If the transmitter is not detected an error message will be displayed Verify that the transmitter is connected to the serial cable and powered up then press Retry A red or green LED should be lit on the transmitter circuit board if it has power If the wrong serial port was selected by mistake the MaxXmtr program will need to be closed and restarted with the correct serial port indicated If the connection is not successful contact your Max Sales Representative for assistance Once serial communication is established the program will automatically read the transmitter data and display the software version on the Information screen SE M 001 Version 3 0 4 3 Max Machinery Inc an ISO 9001 2008 certified company Screenshots To print screen shots of the program use your computer s built in Print Screen function Simply have the MaxXmtr pr
Download Pdf Manuals
Related Search