USER MANUAL - Patriot Supply
Contents
1.2. C upper limit of the thermostat s display range The display will return to normal after the sensed temperature lowers within the 45 to 90 F 7 to 32 C display range This condition could occur from the system being turned off during an exceptionally warm period or upon installation when the thermostat has been stored for a long period of time in a warm vehicle or location prior to being installed SYMPTOM LO is shown in the thermostat display where the room temperature is normally displayed TROUBLESHOOTING cont POTENTIAL SOLUTION The temperature sensed by the thermostat is lower than the 45 F 7 C lower limit of the thermostat s display range The display will return to normal after the sensed temperature rises within the 45 to 90 F 7 to 32 C display range If the temperature in the controlled space seems to be normal wait for the thermostat to acclimate to the correct room temperature This condition could occur from the system being turned off during a cold weather period or upon installation when the thermostat has been stored for a long period of time in a cold vehicle or location prior to being installed The thermostat should be allowed to warm up prior to installation to allow proper heating control once installed Thermostat will not allow me to program a setpoint temperature higher than 90 F 32 C This is above the normal thermostat temperature setting range of 45 to 9
3. Cooling or Heating Transformer Y H W or 4 Wy Heating or Cooling GorF G Fan Control 4 After labeling and removing all wires from terminals unscrew the existing thermostat sub base from wall Be sure to secure wires to prevent them from slipping back into the hole in the wall NOTE This thermostat is designed for use with a 24 Volt AC low voltage single stage gas oil or electric heating or cooling systems This thermostat can also be used on 250mv to 750mv millivolt heating only systems Do not use this thermostat on applications with voltages above 30 Volts AC 2 2 Installing Your New Thermostat NOTE if you are installing this thermostat in a new installation be sure to locate the thermostat 4 to 5 feet above the floor in accordance with applicable building codes Make sure to install the thermostat in a location that provides good airflow characteristics and avoid areas behind doors near corners air vents direct sunlight or near any heat generating device Installation in any of these areas could impact thermostat performance Always turn off power to the air conditioning or heating system prior to installing your new thermostat Place system switch on front of thermostat to OFF position Place fan control switch on front of thermostat to AUTO position Remove front of thermostat body from sub base by pressing release latch on bottom of front body Place the thermostat sub base against wall in the desired thermostat lo
4. any defects that are due to Hot Side Transformer faulty material or workmanship for a period of two years after the original date of purchase by a professional service technician This Transformer 120 warranty and our liability does not apply to batteries nor does it include damage to merchandise or the thermostat resulting from accident Volt AC alteration neglect misuse improper installation or any other failure to follow Braeburn installation and operating instructions Braeburn Systems LLC agrees to repair or replace at its option any Braeburn thermostat under warranty provided it is returned postage prepaid to our warranty facility in a padded carton within the warranty period with proof of the original date of purchase and a brief description of the malfunction This limited warranty does not include the cost of removal or re installation This warranty gives you specific legal rights and you may also have other rights that vary from state to state or province to province Answers to any questions regarding our limited warranty may be obtained by writing our corporate offices Warranty Facility Braeburn Systems LLC Attn Warranty Department 2215 Cornell Avenue Montgomery IL 60538 Braeburn Braeburn Systems LLC 2215 Cornell Avenue Montgomery IL 60538 Technical Assistance www braeburnonline com Phone 866 268 5599 2009 Braeburn Systems LLC All Rights Reserved e U S Patent 7 438 469 Made in China e 1005NCS 100 004
5. to reset a thermostat to regain normal operation This will return all thermostat settings to their default values SYMPTOM Thermostat turns heating or cooling system on too often or not often enough gi TROUBLESHOOTING cont POTENTIAL SOLUTION Increase or decrease temperature differential setting as appropriate to provide the desired performance level See Setting the Temperature Differential section 4 2 of this manual Low battery indicator is shown in thermostat display Replace batteries immediately to maintain proper system operation See Low Battery Detection and Replacement section 5 4 of this manual OFF is shown in thermostat display and heating or cooling system will not start This indicates that the system is turned off at the thermostat Move the system selector switch to the ON position Thermostat display is blank It is possible that the batteries are drained and not providing power for the thermostat to control the system Replace batteries immediately to maintain proper system operation See Low Battery Detection and Replacement section 5 4 of this manual If you replace the batteries and the display does not appear call a professional service technician to verify thermostat and system performance HI is shown in the thermostat display where the room temperature is normally displayed Hi The temperature sensed by the thermostat is higher than the 90 F 32
6. 0 F 7 to 32 Thermostat will not allow me to program a setpoint temperature lower than 45 F 70 This is below the normal thermostat temperature setting range of 45 to 90 F 7 to 32 Fan continues to run all the time whether the system is on or off Check that the fan control switch is in the AUTO position This will allow the fan to run only when the heating or cooling system is turned on and running Check thermostat wiring to make sure that the fan control wiring is connected to the correct terminals on the wiring terminal block See nstallation and Wiring Diagram sections of this manual The room is too warm or too cold See Review Set Temperature section 5 1 of this manual to verify the current setpoint and make any modifications that are necessary 7 WIRING DIAGRAMS Braeburn Typical 2 Wire 24 Volt AC or 250mV 750mV Millivolt Heating Systems R WY G eee D Heat Control VE A R PI 24 Volt AC WARRANTY Hot Side Transformer Transformer HEAT 120 Volt AC RESET SYSTEM FAN ON OFF AUTO ON uo m Typical 3 Wire Single Transformer Heating System or Cooling System i R W Y G o Store this Cool booklet for Control future reference Fan Control 24 Volt AC TWO YEAR LIMITED WARRANTY Braeburn Systems LLC warrants each new Braeburn thermostat against
7. Braeburn Builder Series MODEL Non Programmable 1 00 5 NG Universal Heat Only or Cool Only Digital Thermostat Compatible with low voltage single stage gas oil or electric heating or cooling systems This thermostat can also be used on 250mv to 750mv millivolt heating only systems Do not use this thermostat on applications with voltages above 30 Volts AC CONTENTS El SPECIFICATIONS G ADDITIONAL OPERATION FEATURES A INSTALLATION TROUBLESHOOTING E TESTING YOUR NEW THERMOSTAT Fd WIRING DIAGRAMS El PROGRAMMING USER SETTINGS Important Safety Information WPAN AEE Always turn off power to the air conditioning or heating system prior to installing removing cleaning or servicing thermostat e Read this manual thoroughly prior to installing programming or operating this thermostat e This thermostat is designed for use with a 24 Volt AC low voltage single stage gas oil or electric heating or cooling systems This thermostat can also be used on 250mv to 750mv millivolt heating only systems e Do not use this thermostat on applications with voltages above 30 Volts AC This thermostat requires two 2 properly installed AA alkaline batteries to provide power for the thermostat to properly control the system operation e Wiring must conform to all building codes and ordinances as required by local and national code authorities having jurisdiction e Do not short or jumper across terminals on the gas valve or at the heating
8. C T E STI N G YO U R Short Cycle Protection Timer Reset NEW THERMOSTAT Output Relays off WARNING Read BEFORE Testing 4 2 Setting the Temperature Differential Do not short or jumper across terminals on the gas valve or at the heating or cooling system control board to test the The default settings for the temperature differential is compatible with most systems and applications The temperature differential is thermostat installation This could damage the thermostat and void the warranty normally set at time of installation and usually does not require any modification under normal operating conditions If you feel that your e Do not operate compressor if the outside temperature is below 50 F 10 C This could possibly damage the controlled system is turning on too often simply follow the instructions below cooling system and may cause personal injury i e This thermostat includes an automatic compressor protection feature to avoid potential damage to the cooling system from NOTE The temperature differential settings are the same for both the heating and cooling systems short cycling This thermostat automatically provides a 5 minute delay after turning off the cooling system output to protect the compressor The default setting is 0 5 F 0 25 C The room temperature must change 0 5 F 0 25 C from the setpoint temperature before the thermostat will initiate the system in heating or cooling 1 In normal
9. cation Guide thermostat wires through center hole in sub base Continue to hold sub base against wall Mark placement of mounting holes as appropriate and drill using a 3 16 drill bit Gently tap supplied plastic anchors into the holes in the wall Place the thermostat sub base against the wall in the desired location making sure the mounting holes are aligned as appropriate and the thermostat wires are properly inserting through opening in middle of sub base SEONOOP ON gt 2 TESTING YOUR INSTALLATION cont NEW THERMOSTAT cont 10 Fasten the sub base to wall using supplied screws NOTE Test your thermostat prior to programming any user settings Pressing the RESET button will erase any user entries 11 Connect wires to quick wiring terminal block as appropriate using the new terminal designations Refer to Wiring Diagram section previously programmed This will erase all user settings and return them to their default values of this manual if required for assistance 12 Make sure all of the wire connections are secure and are not touching any other terminal to prevent electrical shorts and potential damage to the thermostat 1 Place the system switch in the ON position 13 Turn the front thermostat body over exposing the rear view of the circuit board 2 For heat only thermostats press the A button on the keypad until the setpoint temperature setting is a minimum of 3 degrees higher 14 Locate the internal HEAT COOL switch on the circui
10. iately to maintain AD D ITI 0 N AL system operation and program settings OPERATION FEATURES 5 1 Review Set Temperature 5 4 1 Replacing the Batteries 1 Press and hold A or V button The current setpoint temperature will be displayed in the place of the current room temperature and the indicator SET will be displayed 2 The display will return to normal operating mode when the A or V buttons are released The SET indicator will turn off indicating that the current temperature shown in the display is the room temperature Continuing to hold the A or V button for 3 seconds or longer will allow the user to change the current setpoint temperature 1 Open the battery compartment door 2 Gently remove the two AA alkaline batteries located in the battery compartment 3 Install two new AA alkaline batteries into battery compartment Make sure to match the positive ends of the batteries with the positive terminals located in the battery compartment 4 Close battery compartment and verify that the low battery indicator does not appear in the display 5 5 Resetting Thermostat 5 2 Changing Set Temperature The Reset feature allows the user to completely reset the thermostat to register new manual switch settings and return to 1 Press and hold A or V button at the same time for 3 seconds The entire display factory set software settings To erase all entered settings gently press RESET button using a paper clip or a small pencil t
11. ip will flash once and the SET indicator will be flashing Release the A or V button and press the A or V button again as desired to adjust the set temperature 2 The display will return to normal operating mode after 5 seconds 3 The SET indicator will turn off in the display indicating that the current temperature shown in the display is the room temperature 6 TROUBLESHOOTING SYMPTOM POTENTIAL SOLUTION Thermostat does not Check to see if OFF is shown in display This indicates that the s turn on heating or system is turned off at the thermostat Move the system selector 5 3 Compressor Protection Feature cooling system switch to the ON position Compressor protection features may be in effect due to compressor short cycle conditions See Compressor Protection Feature section 5 3 for a full explanation of this feature This thermostat includes an automatic compressor protection feature to avoid potential damage to the cooling system from short cycling This thermostat automatically provides a 5 minute delay after turning off the cooling system output to protect the compressor Heating or cooling system may be malfunctioning Call a professional service technician immediately to verify system operation NOTE The installer can reset the thermostat and bypass the compressor protection feature by pressing the RESET button This will erase all user program settings and should only be used during installation for testing purposes or
12. operating mode press and hold both the Aand V buttons at the same time for 4 seconds LCD display will show SET D1 x where x equals the F C differential SET D1 setting This is the current temperature differential setting 2 Press the A or V buttons to set the temperature differential to your desired setting of 5 1 or 2 F 25 displayed as 2 5 or 1 C wn PROGRAMMING ADDITIONAL I USER SETTINGS cont OPERATION FEATURES cont NOTE once you have finished setting the temperature differential you can wait 5 seconds and the thermostat will 5 4 Low Battery Detection and Replacement automatically return to the normal operating mode This thermostat requires two 2 properly installed AA alkaline batteries to provide power for the thermostat to properly NOTE 10 erase all user program settings gently press RESET button using a paperclip or a small pencil tip control the system operation The system must have 24 Volt AC power present for proper system operation and control This will return all thermostat settings to their default values This thermostat is equipped with a low battery detection feature that constantly monitors the batteries during normal operating mode to determine whether they have sufficient power to provide proper operation When this feature determines that the battery status is low a low battery indicator will appear in the display It is recommended that the batteries be replaced immed
13. or cooling system control board to test the thermostat installation This could damage the thermostat and void the warranty e Do not operate compressor if the outside temperature is below 50 F 10 C This could possibly damage the controlled cooling system and may cause personal injury This thermostat should only be used as described in this manual Any other use is not recommended and will void the warranty Zz SPECIFICATIONS e Electrical Rating 24 Volt AC 18 30 Volt AC 1 amp maximum load per terminal 2 amp total maximum load all terminals e Control Range 45 90 F 7 32 C e Accuracy 1 F 5 C e DC Power 3 0 Volt DC 2 AA Alkaline batteries included e Compatibility with low voltage single stage gas oil or electric heating or cooling systems This thermostat can also be used on 250mv to 750mv millivolt heating only systems e Terminations R W Y G INSTALLATION 2 1 Replacing Existing Thermostat 1 Always turn off power to the air conditioning or heating system prior to removing existing thermostat 2 Remove the cover of your old thermostat and locate the wire terminals Do not remove wires from terminals yet 3 Using small pieces of masking tape label wires prior to removal from terminals Use the chart below to determine the new terminal designations for your new thermostat Old Terminal from New Terminal for Existing Thermostat New Thermostat Terminal Description V Re M 4 Rh or R R
14. t board This switch configures for heating HEAT systems or cooling than the current room temperature The heating system should start within several seconds The fan may not turn on immediately due COOL systems to the heating system built in fan delay 15 Using your fingers gently flip the switch towards the HEAT or COOL selection that indicates the system the thermostat will control 3 Place the system switch in the OFF position The heating system should stop within several seconds 16 For heat only applications locate the internal fan option switch HG Gas HE Elec on the circuit board This switch controls the 4 For cool only thermostats press the V button on the keypad until the setpoint temperature is a minimum of 3 degrees lower than the heating system fan delay Select gas for gas or oil fired systems This will allow the furnace to run for a few seconds before current room temperature ae has 7 initiating the fan Select electric for systems with electric furnace elements that require the fan to come on immediately 5 The cooling system should start within several seconds Place the system switch in the OFF position The cooling system should stop 17 Using your finger gently flip the switch towards the HG Gas or HE Elec selection that indicates the low voltage heating system within a few seconds o the thermostat will control 6 Place the fan switch in the ON position The system blower should start 18 Locate the internal F C s
15. witch on the circuit board 7 Place the fan switch in the AUTO position The system blower should stop 19 Using your finger gently flip the switch toward the preferred temperature F C scale 20 Attach front body of thermostat to sub base of thermostat being careful to align the terminal pins on the front body with the terminal block on the sub base 21 Open battery compartment door 22 Install two new AA alkaline batteries into battery compartment Be sure to locate the positive ends of the batteries and PROGRAMMING match them with the positive terminals located in the battery compartment U S E R sS ETTI N G Ss NOTE i you installed the batteries prior to accomplishing steps 14 through 19 then you will need to reset the thermostat to register your thermostat switch configurations 4 1 Default Thermostat Settings prior to programming any user settings Gently press the RESET button on the front of the Function Status After Reset thermostat using a paperclip or a small pencil tip Operation Mode Normal Operating Mode 33 Coenbiieveeienatl Room Temperature 70 F 21 0 C to be renewed within 5 seconds 24 Restore system power so you can test installation Setpoint Temperature According to system switch 62 F 17 0 C for Heat or Off 85 F 29 0 C for Cool Temperature Scale F or C dependent on switch setting Low Battery Warning Off to be renewed within 5 seconds Temperature Differential 0 5 F 0 25
Download Pdf Manuals
Related Search