QB-MINI2 Setup Manual Partner Tool UM
Contents
1. INTUDOR 0x000002C0 rz EON J MC2MON ROM MC2ROM MC2MON RAM MC2RAM Note Use the source names described in the program as the interrupt source names Also describe as the address a vector address corresponding to the interrupt source See the user s manual of the target device for vector addresses Users Manual U19158EJ1VOUM CHAPTER3 USER PROGRAM PREPARATION 3 2 Securing Serial Interface for Communication Create the user program paying attention to the following items O Serial interface registers Do not use the user program for setting the registers related to UART and CSI H S which are used for communication O Serial communication interrupt mask registers Generally do not use the user program for changing the interrupt mask registers of UART and CSI H S which are used for communication To use the IMR register to change the interrupt mask settings in a batch do not change the setting values of the target interrupt masks by a read modify write operation O Port related registers To use UART for communication do not perform register settings for ports such that the TxD and RxD pins become invalid For CSI H S do not perform register settings for ports such that the SI SO SCK and H S pins become invalid The H S pin is used as the port output for debugging Two examples are described below Example 1 Settings other than the following are prohibited when the V850ES KJ2 is the target device and UAR2. This chapter describes the procedure up to starting the MULTI debugger 1 Connection organizer start Click the target connection button in the MULTI launcher to open the connection organizer as shown below ni MULTI Eile Utilities Windows Processes Confie Help ewe E S Bed Information about the MULTI Launcher cher sk akg Connect to Target The MULTI Launcher toolbar provides the ability to easily launch all major IDE components and manage user defined workspaces that can be customized to your common working environments Click this button to open the connection organizer If you have not yet installed your product licenses you should use the License Manager Administration utility to install them first To create a workspace select entry Create Workspace from the File menu To hide this information at the next startup check the Don t show this message again box below Start with MULTI Launcher Don t show this message again 2 Creating a new method Select New from the Method menu in the connection organizer menu bar as shown below Select New from Method in the menu bar Um paar a tand Gebue Open Executable Type 778501 Simulator for V80 sim amp 85n Users Manual U19158EJ1VOUM CHAPTER 5 MULTI DEBUGGER START 3 Setting a new method Set the items in the new method dialog box and clic
3. but Renesas Electronics does not warrant that such information is error free Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein Renesas Electronics products are classified according to the following three quality grades Standard High Quality and Specific The recommended applications for each Renesas Electronics product depends on the product s quality grade as indicated below You must check the quality grade of each Renesas Electronics product before using it in a particular application You may not use any Renesas Electronics product for any application categorized as Specific without the prior written consent of Renesas Electronics Further you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as Specific or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics The quality grade of each Renesas Electronics product is Standard unless otherwise expressly specified in a Renesas Electronics data sheets or data books etc Standard Computers off
4. Debugging Internal ROM space Internal RAM space Internal RAM end address Internal ROM end address 10 to 16 bytes Note CSI or UART receive interrupt vector 0x70 security ID area 0x60 interrupt vector for debugging 0 0 reset vector 1 Monitor program area for debugging Note When there is a receive error interrupt or a receive status interrupt the corresponding vector must be secured 10 Users Manual U19158EJ1VOUM 1 CHAPTER USER PROGRAM PREPARATION Example 1 of securing memory space and setting the security ID e Program description Add the following as the assemble source DBGO Vector section DBGO ax 0x60 word Security ID fHHt Set ID code arbitrarily section TE CODE a 0x70 byte Oxff Oxff Oxff Oxff Oxff Oxff Oxff Oxff Oxff H Serial Receive Interrupt Vector section INTCBOR ax ae word ed ROM area secured for MINICUBE2 MONITOR section MC2MON ROM ax rept 0x200 word endr ed RAM area secured for MINICUBE2 MONITOR section MC2MON RAM global monitorramsym monitorramsym space 16 Note This description is applicable when CSIBO is used as the interface of MINICUBE2 and the target device Change the INTCBOR section according to the receive interrupt source of serial communication See Appendix A for interrupt source
5. Please check with an NEC Electronics sales representative for availability and additional information No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics NEC Electronics assumes no responsibility for any errors that may appear in this document NEC Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products No license express implied or otherwise is granted under any patents copyrights or other intellectual property rights of NEC Electronics or others e Descriptions of circuits software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples The incorporation of these circuits software and information in the design of a customer s equipment shall be done under the full responsibility of the customer NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits software and information e While NEC Electronics endeavors to enhance the quality reliability and safety of NEC Electronics products customers agree and acknowledge that the possibility of defects thereof cannot be eliminated e
6. WARNING RSU id code 0x70 0x79 has changed New id code is ffffffffffffIfffffff running D Micom tool Env MINICUBE2_ sample mini2 40 out Target Target run gt Target run gt Target run break by software break MULTI gt E T vo T 5 J STOPPED 22 Users Manual U19158EJ1VOUM APPENDIX A INTERRUPT SOURCE NAMES AND START OPTIONS Target Device MINICUBE2 Interrupt Vector p Option Connection Serial Specification Communication V850ES Fx3 CSIBO INTCBOR CSIBO receive complete interrupt UARTDO INTUDOS UARTDO status interrupt INTUDOR UARTDO receive complete interrupt INTUDOS UARTDO status interrupt INTCBOR CSIBO receive complete interrupt UARTDO INTUDOR UARTDO receive complete interrupt uartdO CSIBO INTCBOR CSIBO receive complete interrupt csibO V850ES FG3L V850ES Hx2 UARTAO INTUAOR UARTAO receive complete interrupt uartaO CSIBO INTCBOR CSIBO receive complete interrupt csibO UARTDO INTUDOR UARTDO receive complete interrupt uartdO CSIBO INTCBORE CSIBO receive error interrupt csibO INTCBOR CSIBO receive complete interrupt UARTAO INTUAORE UARTAO receive error interrupt INTUAOR UARTAO receive complete interrupt INTCBORE CSIBO receive error interrupt INTCBOR CSIBO receive complete interrupt UARTAO INTUAORE UARTAO receive error interrupt INTUAOR UARTAO receive complete interrupt INTCBORE CSIBO receive error interrupt INTCBOR CSIBO receive complete interr
7. certain use conditions Further Renesas Electronics products are not subject to radiation resistance design Please be sure to implement safety measures to guard them against the possibility of physical injury and injury or damage caused by fire in the event of the failure of a Renesas Electronics product such as safety design for hardware and software including but not limited to redundancy fire control and malfunction prevention appropriate treatment for aging degradation or any other appropriate measures Because the evaluation of microcomputer software alone is very difficult please evaluate the safety of the final products or system manufactured by you Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances including without limitation the EU RoHS Directive Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations This document may not be reproduced or duplicated in any form in whole or in part without prior written consent of Renesas Electronics Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Elect
8. granted hereby under any patents copyrights or other intellectual property rights of Renesas Electronics or others You should not alter modify copy or otherwise misappropriate any Renesas Electronics product whether in whole or in part Descriptions of circuits software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples You are fully responsible for the incorporation of these circuits software and information in the design of your equipment Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits software or information When exporting the products or technology described in this document you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military including but not limited to the development of weapons of mass destruction Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture use or sale is prohibited under any applicable domestic or foreign laws or regulations Renesas Electronics has used reasonable care in preparing the information included in this document
9. names They are also listed in the user s manual of the target device Refer to the following page when there is a receive error interrupt or a receive status interrupt User s Manual U19158EJ1VOUM 11 CHAPTER3 USER PROGRAM PREPARATION e Linker directive description Insert the following into the linker directive The following example is applicable when the internal ROM size is 256 KB and the internal RAM end address is Ox3ffefff MEMORY iROM ORIGIN 0 00000000 LENGTH 256k 2k MC2ROM ORIGIN 254k LENGTH 2k iRAM ORIGIN OxOSFFCO000 LENGTH 12k 16 MC2RAM ORIGIN OxOSFFEFFO LENGTH 16 SECTIONS RESET 0x00000000 gt DBGO 0x00000060 gt IRON S_CODE 0x00000070 gt IRON INTCBOR 0x00000230 rz EON AITE MC2MON ROM MC2ROM MC2MON RAM MC2RAM Note Use the source name described in the program as the interrupt source name INTCBOR section Also describe as the address a vector address corresponding to the interrupt source See the user s manual of the target device for vector addresses Users Manual U19158EJ1VOUM CHAPTER3 USER PROGRAM PREPARATION 2 Example 2 of securing memory space and setting the security ID when there is a receive status interrupt during serial communication e Program description Add the following as the assemble source Vector section DBGO ax 0x60 word H Security ID fHHt
10. 9 81829 M nchen Tel 0 89 92 10 03 0 Stuttgart Office Industriestrasse 3 70565 Stuttgart Tel 0 711 99 01 0 0 United Kingdom Branch Cygnus House Sunrise Parkway Linford Wood Milton Keynes MK14 6NP U K Tel 01908 691 133 Succursale Francaise 9 rue Paul Dautier B P 52 78142 Velizy Villacoublay C dex France Tel 01 3067 5800 Sucursal en Espana Juan Esplandiu 15 28007 Madrid Spain Tel 091 504 2787 Tyskland Filial Taby Centrum Entrance S 7th floor 18322 Taby Sweden Tel 08 638 72 00 Filiale Italiana Via Fabio Filzi 25 A 20124 Milano Italy Tel 02 667541 Branch The Netherlands Steijgerweg 6 5616 HS Eindhoven The Netherlands Tel 040 265 40 10 Asia amp Oceania NEC Electronics China Co Ltd 7th Floor Quantum Plaza No 27 ZhiChunLu Haidian District Beijing 100083 P R China Tel 010 8235 1155 http www cn necel com Shanghai Branch Room 2509 2510 Bank of China Tower 200 Yincheng Road Central Pudong New Area Shanghai P R China P C 200120 Tel 021 5888 5400 http www cn necel com Shenzhen Branch Unit 01 39 F Excellence Times Square Building No 4068 Yi Tian Road Futian District Shenzhen P R China P C 518048 Tel 0755 8282 9800 http www cn necel com NEC Electronics Hong Kong Ltd Unit 1601 1613 16 F Tower 2 Grand Century Place 193 Prince Edward Road West Mongkok Kowloon Hong Kong Tel 2886 9318 http www hk necel com NEC Electronics
11. Japanese version http www necel com micro ods jpn Click Version up Service English version http www necel com micro ods eng Click Version up Service Users Manual U19158EJ1VOUM 9 CHAPTER 3 USER PROGRAM PREPARATION The following preparations must be performed for user programs so that MINICUBE2 can communicate with the target device and perform each debug function These preparations require the user programs and linker directive to be edited Refer to the following 3 1 Securing Memory Space and Setting Security ID to perform editing and building 3 1 Securing Memory Space and Setting Security ID The shaded areas in Figure 3 1 are areas to which user programs and data cannot be placed because a monitoring program for debugging will be built in The 10 byte areas shown in yellow are areas to which ID codes are embedded so that the contents of a memory cannot be read by a third party When using MULTI MINICUBE2 can be started when the security ID and embedded ID match as the argument of 850eserv start option id Be sure therefore to surely manage the embedded security ID code If the ID code is forgotten the flash memory must be erased and the debugger must be restarted with the ID code set as Oxffffffffffffffffffff 10 bytes To secure memory space and set the security ID describe the assemble source and linker directive source shown on the next page Figure 3 1 Memory Spaces Is Placed A Monitoring Program For
12. Set ID code arbitrarily section TE CODE a 0x70 byte Oxff Oxff Oxff Oxff Oxff Oxff Oxff fHHt Serial Receive amp Status Interrupt Vector section INTUDOS ax did word section INTUDOR ax 22598 word ROM area secured for MINICUBE2 MONITOR section MC2MON ROM ax rept 0x200 word endr H RAM area secured for MINICUBE2 MONITOR section MC2MON RAM global monitorramsym monitorramsym space 16 Note This description is applicable when UARTDO is used as the interface of MINICUBE2 and the target device Change the interrupt name according to the receive interrupt and receive status interrupt of serial communication See Appendix A for interrupt source names They are also listed in the user s manual of the target device User s Manual U19158EJ1VOUM 13 CHAPTER3 USER PROGRAM PREPARATION e Linker directive description Insert the following into the linker directive The following example is applicable when the internal ROM size is 256 KB and the internal RAM end address is Ox3ffefff MEMORY iROM ORIGIN 0 00000000 LENGTH 256k 2k MC2ROM ORIGIN 254k LENGTH 2k iRAM ORIGIN OxOSFFCO000 LENGTH 12k 16 MC2RAM _ ORIGIN OxOSFFEFFO LENGTH 16 SECTIONS RESET 0x00000000 gt IRON DBGO 0x00000060 gt IRON S_CODE 0x00000070 gt IRON INTUDOS 0x000002B0 rz EON J
13. TO is used 7 6 5 4 3 2 1 0 Ex x fx x fx x fo PFC3 x Arbitrary 7 6 5 4 3 2 1 0 ewan D D X Arbitrary Example 2 Settings other than the following are prohibited when the V850ES HG2 is the target device and CSIBO is used 7 6 5 4 3 2 1 0 X Arbitrary 7 6 5 4 3 2 1 0 PCT 7 X Arbitrary 7 6 5 4 3 2 1 0 7 X Arbitrary 7 6 5 4 3 2 1 0 Lede Tee fe I PX bronibied X Arbitrary Note The monitoring program changes the port value corresponding to the H S pin according to the debugger status When port register settings are to be manipulated in 8 bit units there will be no problem if read modify writing is performed in the user program but an unintended operation may result if an interrupt for debugging occurs before writing User s Manual U19158EJ1VOUM 15 CHAPTER 4 SYSTEM START Start the system by using the following procedure 1 MINICUBE2 switch setting Set the mode selection switch to M2 V850 microcontroller connection setting Set the power supply selection switch referring to the following table Caution Do not toggle the MINICUBE2 switch when a USB cable is connected Remove the USB cable when toggling the switch Table 4 1 Power Supply Selection Switch Setting Setting Description Supplies 3 V from MINICUBE2 to the target system Supplies 5 V from MINICUBE 2 to the target system Uses the target s
14. Taiwan Ltd 7F No 363 Fu Shing North Road Taipei Taiwan R O C Tel 02 8175 9600 http www tw necel com NEC Electronics Singapore Pte Ltd 238A Thomson Road 12 08 Novena Square Singapore 307684 Tel 6253 8311 http www sg necel com NEC Electronics Korea Ltd 11F Samik Lavied or Bldg 720 2 Yeoksam Dong Kangnam Ku Seoul 135 080 Korea Tel 02 558 3737 http www kr necel com G0706
15. To our customers Old Company Name in Catalogs and Other Documents On April 1 2010 NEC Electronics Corporation merged with Renesas Technology Corporation and Renesas Electronics Corporation took over all the business of both companies Therefore although the old company name remains in this document it is a valid Renesas Electronics document We appreciate your understanding Renesas Electronics website http www renesas com April 1 2010 Renesas Electronics Corporation Issued by Renesas Electronics Corporation http www renesas com Send any inquiries to http www renesas com inquiry 2 NE S AS 10 11 12 Notice All information included in this document is current as of the date this document is issued Such information however is subject to change without any prior notice Before purchasing or using any Renesas Electronics products listed herein please confirm the latest product information with a Renesas Electronics sales office Also please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website Renesas Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document No license express implied or otherwise is
16. anual have general knowledge in the fields of electrical engineering logic circuits and microcontrollers This manual describes the basic setup procedures To understand the basic specifications and usages of MINICUBE2 Read this manual according to the CHAPTER 1 GENERAL To know the manipulations command functions and other software related settings of MINICUBE2 See the user s manual of the debugger to be used Note Footnote for item marked with Note in the text Caution Information requiring particular attention Remark Supplementary information Numeric representation Binary xxxx or xxxxB Decimal Xxxx Hexadecimal xxxxH Prefix indicating power of 2 address space memory capacity kilo 2 1 024 M mega 2 1 024 User s Manual U19158EJ1VOUM 5 Terminology The meanings of the terms used in this manual are described in the table below MINICUBE2 Generic name of QB MINI2 Target device This is the device to be emulated Target system This is the system to be debugged user created system Refers to all hardware and software provided by the user MULTI Integrated development environment MULTI manufactured by Green Hills Software Related Documents Please use the following documents in conjunction with this manual The related documents listed below may include preliminary versions However preliminary versions are not marked as such Documents Related to Development Tool
17. ebugger It is included with integrated development environment MULTI and should be installed together with MULTI Use the latest version of 850eserv due to the relation with the Exec library described in 3 below 3 Exec library This is the dynamic link library called by 850eserv to control MINICUBE2 Due to the relation with 850eserv described in 2 above download the latest version of the Exec library from the following Web sites and copy the complete set of extracted files to the same folder as MULTI exe Japanese Web site http www necel com micro ghs jpn exec execindex html English Web site http www necel com micro ghs eng exec index html 4 USB driver for MINICUBE2 This USB driver is required to connect the host machine and MINICUBE2 Download it from the same Web site as the Exec library described in 3 above and extract it A plug and play dialog will be displayed when MINICUBE2 and the host machine are connected after the USB driver file has been extracted Specify as the destination for storing the USB driver the folder that was extracted before MQB2ALL 5 Device file This file holds device specific information and is used by 850eserv Download it from the following Web sites and extract it The device file name after extracting 800 file extension and the path information of the extracted folder are used for specifying options when starting the MULTI debugger For details see CHAPTER 5 MULTI DEBUGGER START
18. he folder generated when the device file was extracted see CHAPTER 2 5 Device file Specify the folder in which the device file is stored Specify the security ID Required option Option enabling referencing of programmable I O area memories and changing memories It is set when using the memory window to reference programmable I O areas Does not clear the BBS area to zero when downloading default Specify this option when clearing the BBS area to zero when downloading 5 MINICUBE2 connection check As required When the Connect button in the connection editor dialog box is clicked 850eserve and MINICUBE2 communicate and if a normal connection between them is confirmed Connected will be displayed in the status column of the connection organizer as shown below See the V850E ICE Server Reference Manual document included in the MULTI environment set when an error has occurred E Connection Organizer File Method Target Opened Connection Files User Methods User Methods EE Connected Targets Name C Green V600 V407 SS0eserv minicube2 noint edi Wed Nov 14 Status Connected E Connected is displayed in the status column when connection is completed 20 Users Manual U19158EJ1VOUM CHAPTER 5 MULTI DEBUGGER START The following error message will be displayed when the p parameter is not set normally In such a ca
19. ice equipment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots High Quality Transportation equipment automobiles trains ships etc traffic control systems anti disaster systems anti crime systems safety equipment and medical equipment not specifically designed for life support Specific Aircraft aerospace equipment submersible repeaters nuclear reactor control systems medical equipment or systems for life support e g artificial life support devices or systems surgical implantations or healthcare intervention e g excision etc and any other applications or purposes that pose a direct threat to human life You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics especially with respect to the maximum rating operating supply voltage range movement power voltage range heat radiation characteristics installation and other product characteristics Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges Although Renesas Electronics endeavors to improve the quality and reliability of its products semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under
20. k the Create button as shown below Name ESERVMC2 0 0 0 0 Name amita name NEC V850 V850E ICE 850eserv Type Select as shown at left Click the Create button 4 Connection editor editing Enter options in the Other Options field in the connection editor dialog box See Table 5 1 for option contents The entry in the figure below is as follows the tail of the entry is hidden in the figure minicube2 noint p csibO df df3707 800 id ffffffffffffffffffff D Xdevice fileX v850e Click the Connect button after the options have been entered Enter the options See the Table 5 1 for options Click the Connect button after having entered the options Users Manual U19158EJ1VOUM 19 CHAPTER 5 MULTI DEBUGGER START Table 5 1 Option Description Content minicube2 Option to be set when MINICUBE2 is the target Necessity of Description Required option noint Sets to non interactive mode when a pio a register or an sfr command is issued When non interactive mode is set a wait for input is not performed when the option is referenced Recommended option Specifies the name of the serial communication that connects MINICUBE2 Specify it by referring to APPENDIX A INTERRUPT SOURCE NAMES AND START OPTIONS Specify the device file name 800 file extension according to the target device See the device file user s manual pdf expanded in t
21. nified GUI Programs can be developed efficiently when MULTI is used together with on chip debug emulator MINICUBE2 with a programming function A combined environment of MULTI and MINICUBE2 can be easily built by setting up a system according to this manual Figure 1 1 Environment By Combining MINICUBE2 And MULTI Building a debugging environment for the a target system by combining MINICUBE2 and MULTI MULTI Microcontroller B 16 pin target Target system cable MINICUBE2 USB cable PC An overview of the setup flow is shown below The setup is described in the following chapter Figure 1 2 setup flow Software tool installation Required software tools are installed Memory space required for debugging is User program preparation secured and security ID settings are described to a program MINICUBE2 the host machine and the System start target system are connected and power is activated The 850eserv startup option is set and the MULTI debugger start MULTI debugger is started 8 Users Manual U19158EJ1VOUM CHAPTER 2 SOFTWARE TOOL INSTALLATION Install the following software tools 1 MULTI debugger This is the integrated development environment MULTI debugger manufactured by Green Hills Software Execute setup exe to install the debugger For details see the document related to MULTI 2 850eserv This is the debug server used to connect MINICUBE2 and the MULTI d
22. ntirely To minimize risks of damage to property or injury including death to persons arising from defects in NEC Electronics products customers must incorporate sufficient safety measures in their design such as redundancy fire containment and anti failure features NEC Electronics products are classified into the following three quality grades Standard Special and Specific The Specific quality grade applies only to NEC Electronics products developed based on a customer designated quality assurance program for a specific application The recommended applications of an NEC Electronics product depend on its quality grade as indicated below Customers must check the quality grade of each NEC Electronics product before using it in a particular application Standard Computers office equipment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots Special Transportation equipment automobiles trains ships etc traffic control systems anti disaster Systems anti crime systems safety equipment and medical equipment not specifically designed for life support Specific Aircraft aerospace equipment submersible repeaters nuclear reactor control systems life support systems and medical equipment for life support etc The quality grade of NEC Electronics products is Standard unless otherwi
23. ronics products or if you have any other inquiries Note 1 Renesas Electronics as used in this document means Renesas Electronics Corporation and also includes its majority owned subsidiaries Note 2 Renesas Electronics product s means any product developed or manufactured by or for Renesas Electronics 434 NE SAS User s Manual QB MINI2 Setup Manual Partner Tool Target Devices V850 Microcontrollers Document No U19158EJ1VOUMOO 1st edition Date Published March 2008 NS NEC Electronics Corporation 2008 Printed in Japan MEMO 2 Users Manual U19158EJ1VOUM MINICUBE is a registered trademark of NEC Electronics Corporation in Japan and Germany and Germany or a trademark in the United States of America Windows is either a registered trademarks or a trademark of Microsoft Corporation in the United States and or other countries Green Hills Software and MULTI are a trademark of Green Hills Software Inc in the United States All other trademarks or registered trademarks are the property of their respective owners Users Manual U19158EJ1VOUM 3 The information in this document is current as of March 2008 The information is subject to change without notice For actual design in refer to the latest publications of NEC Electronics data sheets or data books etc for the most up to date specifications of NEC Electronics products Not all products and or types are available in every country
24. s User s Manuals Document Name Document Number QB MINI2 On Chip Debug Emulator with Programming Function User s Manual U18371E QB MINI2 Operating Precautions ZUD CD 07 1212 E QB Programmer Programming GUI Operation User s Manual U18527E MINICUBE2 Diagnostic Tool User s Manual U18588E MINICUBE OCD Checker User s Manual U18591E Caution The related documents listed above are subject to change without notice Be sure to use the latest version of each document for designing etc 6 Users Manual U19158EJ1VOUM CONTENTS CHAPTER T GENERAL EE EAE aa a a 8 CHAPTER 2 SOFTWARE TOOL INSTALLAT ION saso 9 CHAPTER USER PROGRAM a 10 3 1 Securing Memory Space and Setting Security ID e 10 3 2 Securing Serial Interface for Communication ea 15 CHAPTER 4 SYSTEM START urera Tera ER c ERE Ene TE aea 16 CHAPTER 5 MULTI DEBUGGER START ecce esee ea 18 APPENDIX A INTERRUPT SOURCE NAMES AND START 23 APPENDIX B MINICUBE2 SELF DIAGNOSIS AND FIRMWARE UPDATE 24 Users Manual U19158EJ1VOUM 7 CHAPTER 1 GENERAL MULTI manufactured by Green Hills Software provides a high performance and user friendly integrated development environment based on a u
25. se confirm whether the option descriptions of the connection editor are correct MULTI v4 0 7 05 sep 26 Users Manual U19158EJ1VOUM 21 CHAPTER 5 MULTI DEBUGGER START 6 MULTI debugger start and clock settings Start the MULTI debugger from the MULTI launcher Execute the dclock command from the command pane as follows In the example the main clock is set to 5 MHz and the sub clock is set to 32 768 kHz Change the settings as required Specify an oscillation clock a clock before PLL multiplication as the main clock MULTI gt dclock 5000 32768 swoff The base window of the debugger immediately after steps 1 to 6 have been executed and the program has been downloaded is shown below See the following documents for the debug operations hereinafter e MULTI debugger command MULTI User s Guide Debugger 850eserv target command V850E ICE Server Reference Manual FR Env MINICUBE2 sample mini2_40 out ES Dati E Se Es ORA ENKAN B dd br d ES E DQQHAHNBAAD 23 int b 24 short c 25 char d 26 27 28 29 E Main Module 30 EA 31 void main void 32 33 34 cub ETO 35 36 37 38 39 40 9 Main Routine 41 10 while i 42 11 43 i2wb i i 1 44 13 e val i val 45 14 46 15 e Timer Initiarize init timer GO Jo 50 E b 47 16 b 2 X ofa MULTI target dclock 5000 32768 swoff E h Downloading program to emulator Please Wait
26. se expressly specified in NEC Electronics data sheets or data books etc If customers wish to use NEC Electronics products in applications not intended by NEC Electronics they must contact an NEC Electronics sales representative in advance to determine NEC Electronics willingness to support a given application Note 1 NEC Electronics as used in this statement means NEC Electronics Corporation and also includes its majority owned subsidiaries 2 NEC Electronics products means any product developed or manufactured by or for NEC Electronics as defined above M8E 02 11 1 Users Manual U19158EJ1VOUM Readers Purpose Organization How to Read This Manual Conventions INTRODUCTION This manual is intended for engineers who use QB MINI2 alias MINICUBE2 as well as MULTI manufactured by Green Hills Software hereinafter referred to as MULTI for debugging Engineers who read this manual are presumed to have a good knowledge of the functions of the device and how to use it as well as debuggers The purpose of this manual is to help users understand the basic ways of using MINICUBE2 and MULTI when introducing them This manual is divided into the following sections e General e Software tool installation e User program preparation e System start e Multi debugger start e Interrupt source names and start options e MINICUBE2 self diagnosis and firmware update It is assumed that the readers of this m
27. upt UARTAO INTUAORE UARTAO receive error interrupt INTUAOR UARTAO receive complete interrupt V850ES Hx3 V850E IA4 V850ES IE2 V850ES Ix3 V850ES Jx2 V850ES Jx3 V850ES Kx1 V850ES Kx2 V850E MA3 User s Manual U19158EJ1VOUM 23 APPENDIX B 2 SELF DIAGNOSIS AND FIRMWARE 24 UPDATE When MINICUBEZ2 is not operating correctly the MINICUBE utilities can be used to perform a self diagnosis The MINICUBE utilities are also used when updating the internal firmware of MINICUBE2 The MINICUBE utilities can be downloaded from the following Web sites See the included documents for how to use them Japanese Web site http www necel com micro ghs jpn exec execindex html English Web site http www necel com micro ghs eng exec index html Users Manual U19158EJ1VOUM MEMO User s Manual U19158EJ1VOUM 25 For further information please contact NEC Electronics Corporation 1753 Shimonumabe Nakahara ku Kawasaki Kanagawa 211 8668 Japan Tel 044 435 5111 http www necel com America NEC Electronics America Inc 2880 Scott Blvd Santa Clara CA 95050 2554 U S A Tel 408 588 6000 800 366 9782 http www am necel com Europe NEC Electronics Europe GmbH Arcadiastrasse 10 40472 D sseldorf Germany Tel 0211 65030 http www eu necel com Hanover Office Podbielskistrasse 166 B 30177 Hannover Tel 0 511 33 40 2 0 Munich Office Werner Eckert Strasse
28. ystem power supply MINICUBE2 detects the target system power supply Also MINICUBE2 uses that power supply for the communication interface Note The maximum rated current is 100 mA Do not use a target system exceeding this value Also power is always supplied when MINICUBE2 and the host machine are connected 2 Target system connection Connect MINICUBE2 and the target system as shown in the Figure 4 1 At this time the power of the target system must be turned off Figure 4 1 Connection of MINICUBE2 and Target System g ZTO 16 pin target cable MINICUBE2 g 7 Target system 16 Users Manual U19158EJ1VOUM CHAPTER4 SYSTEM START 3 USB connection Connect MINICUBE2 and the target system as shown in the Figure 4 2 At this time the power of the target system must be turned off When the power supply selection switch is set to T the mode LED blinks in white after connection When the power supply selection switch is set to 3 or 5 the mode LED glows steadily in white after connection Figure 4 2 Connection of MINICUBE2 and Host Machine ET Se pn ezee _ MINICUBE2 USB cable Host machine 4 Target system power activation Activate the power of the target system When the power supply selection switch is set to 3 or 5 this step is not required mode LED glows steadily in white after power activation Users Manual U19158EJ1VOUM 17 18 CHAPTER 5 MULTI DEBUGGER START
Download Pdf Manuals
Related Search