WEBs-AX GPRS Modem
Contents
1. Modem Checkout After mounting the NPB GPRS H modem option and attaching the antenna power the controller on Following reboot of the controller the modem is configured by opening a platform connection to the controller To verify modem communications verify that status properties in the GPRS Modem Configuration platform view show returned values 62 0301 01 WEBS AX GPRS MODEM RELATED DOCUMENTATION For more information on mounting and wiring a WEBs AX controller refer to the following documents e WEB 201 600 Installation Instructions Form no 95 7722 e WEB 700 Installation Instructions future release e WEB 870 Installation Instructions future release For the NiagaraAX software configuration and operation of the installed GPRS modem option e NiagaraAX GPRS modem option Engineering Notes Automation and Control Solutions Honeywell International Inc 1985 Douglas Drive North Golden Valley MN 55422 customer honeywell com 35 Dynamic Drive U S Registered Trademark Toronto Ontario M1V 4Z9 OPTIONS AND PARTS The following options and replacement parts may be ordered for the NPB GPRS H or NPB GPRS W H modem Table 1 Parts for WEBs AX GPRS modem Option Part Description H GPRS CBL 6 56 ft 2m SMA type coax extension EXT cable and mounting bracket See Antenna Extension Option on page 3 H GPRS SIM W Replacement SIM card provisioned by Wyless NPB GPRS H Replacem2. pletely seated INSERT NPB GPRS H CARD INTO OPTION CARD SLOT CAREFULLY WITH PINS ALIGNED FULLY SEAT CARD 201 OR 600 CONTROLLER BATTERY CONNECTOR PLACE NPB GPRS H CUSTOM PLATE OVER END M29146 Fig 4 NPB GPRS H inserted end plate on top 6 Plug the battery cable into the battery connector on the controller see Fig 4 for location 7 Set the battery and bracket assembly back over the option card slots with the mounting holes aligned with the standoffs 8 Place the four screws through the battery bracket end plates and into the standoffs on the controller base board Hand tighten these screws HAND TIGHTEN THE FOUR SCREWS THROUGH BATTERY BRACKET END PLATES INTO STANDOFFS Fig 5 Re fasten screws through battery bracket 9 Replace the controller cover If accessory modules were unplugged plug them back into the controller as before and secure ATTACHING ANTENNA A GSM GPRS stub antenna with right angle SMA male coax connector is provided for use with WEB 201 WEB 600 WEB 700 controller To attach simply insert into the SMA coax jack on the modem and finger tighten the knurled nut Fig 3 SUB ANTENNA INSTALLED ON NPB GPRS MODEM OPTION CARD Fig 6 SMA stub antenna on WEB 201 600 Rotate in whatever position is needed for mounting clearance and or best reception If needed you can use the H GPRS CBL EXT Antenna Extension Option Antenna Extension Option To loc
3. Honeywell WEBs AX GPRS Modem This document covers the mounting of the NPB GPRS H NPB GPRS W H wireless modem option card in a WEB 201 WEB 600 WEB 700 or WEB 870 controller Description WEBs AX GPRS cellular modem option card is designed to mount in an option card slot of a WEB 201 WEB 600 WEB 700 or WEB 870 controller This modem uses GPRS General Packet Radio Service data technology and has 2 LED indicators for status and signal An antenna with an SMA coax connector is included in the package An optional coax extension cable is available for remote mounting NOTES The GPRS modem requires a SIM subscriber identity module card from an approved vendor At the time this document was created only a SIM card provisioned by Wyless Group is supported WEBs controllers require NiagaraAX build 3 4 or later to support operation of the GPRS modem Not covered in this document is the software setup and operation of the installed GPRS modem option Refer to the NiagaraAX GPRS modem option engineering notes document for this information For all other related mounting and wiring details refer to the appropriate mounting and wiring document See Related Documentation on page 4 Included in this Package Included in this package you should find the following items e An NPB GPRS H modem option card with pre attached endplate Ifan NPB GPRS W H a Wyless provisioned SIM card ready for Pre installati
4. ate the included stub antenna remotely from controller order and install the H GPRS CBL EXT option Included is a 6 56 ft 2m SMA type coax extension cable and steel bracket for wall or panel mounting See Fig 7 for bracket details and dimensions WEBS AX GPRS MODEM y 1 1 4 32 4 1 1 8 30 1 MOUNTING HOLES 2 1 64 4 M29149 Fig 7 H GPRS CBL EXT bracket details Some installations may require a different external antenna NOTE Any external antenna must be compatible with the GSM 900 1800 frequency and the 50Q impedance of the SMA coax connector on the NPB GPRS H modem LEDS Two LEDs are located on the endplate of the NPB GPRS H option card On the option card label these appear as STATUS and SIGNAL see Fig 1 on page 1 These two LEDs are briefly described as follows e STATUS green Flashes various LED patterns based on the state of the modem This LED is directly under control of the modem itself rather than the NiagaraAX modem driver Upon initial power up the Status LED pattern is typically 600ms On 600ms Off and may change depending on various modem state changes e SIGNAL green Indicates the RSSI received signal strength indicator according to the number of short 350ms On flash patterns Analogous to number of bars on a cell phone For further details on the operation of both LEDs see the NiagaraAX GPRS modem option Engineering Notes document
5. ent GPRS modem option card without bundled SIM card APPROVALS FCC The Siemens TC63 cellular communications module used on the NPB GPRS H modem option card is FCC approved and has an FCC ID of QIPTC63 Honeywell Limited Honeywell Limit e Honeywell 4 Printed in U S A on recycled 2009 Honeywell International Inc amp paper containing at least 10 62 0301 01 M S 02 09 post consumer paper fibers
6. m the controller see the previous Warning 2 For a WEB 201 600 or 700 remove the cover To do this press in the four tabs on both ends of the unit and lift the cover off NOTE If accessory modules are plugged into the controller you may need to slide them away from the unit to get to the cover tabs 3 Remove the battery and bracket assembly by taking out the four screws holding it in place setting the screws aside for later Unplug the battery from the connector on the controller Fig 3 shows an exploded view of a WEB 201 600 62 0301 01 2 SCREWS 4 BATTERY ASSEMBLY INCLUDES CABLE AND BRACKET BLANKING END PLATE OPTION SLOT 1 AREA 201 OR 600 CONTROLLER Fig 3 Remove screws and battery assembly NOTE The tie wrap on the battery pack should have its lock knot on top as shown in Figure 3 If not cut and remove the tie then re install another tie wrap with its lock tab on top Tie lock at bottom interferes with option card 4 Remove the blanking end plate for the slot you are installing the option card into Retain the blanking end plate in case the option card must be removed at a later date 5 Carefully insert the pins of the NPB GPRS H into the socket of the appropriate option card slot The mounting holes on the option board should line up with the stand offs on the base board If they do not the connector is not properly aligned Press until the option card is com
7. on INSTALLATION INSTRUCTIONS Aright angle GSM GPRS quad band SMA coax mounted stub antenna This document WEBs AX GPRS Modem Installation Sheets LEDS 2 STATUS SIGNAL ANTENNA SUPPLIED CONNECTOR STUB SMA COAX ANTENNA M29144 Fig 1 NPB GPRS H Modem Option Material and Tools Required The following supplies and tools are required SIM card from approved wireless service provider 2 phillips screwdriver used to install the NPB GPRS H option card PRE INSTALLATION Prior to mounting the NPB GPRS H modem option card in the controller install the SIM card into the connector on the underside of the option card 62 0301 01 WEBS AX GPRS MODEM SEATED FULLY IN CONNECTOR M29145 CORNER OUT Fig 2 Inserting SIM into underside of NPB GPRS H To install orient the SIM with its foil connectors down writing side up and its angled corner out and slide fully into the connector See Fig 2 above MOUNTING A WARNING Power to the controller must be OFF when installing or removing option cards or damage will occur Be very careful to plug any option card into its connector properly pins aligned Mount the NPB GPRS H card in either of the available option card slots of a WEB 201 WEB 600 WEB 700 or WEB 870 controller If mounting on a WEB 870 controller the upper option slot Slot 2 is recommended Procedure 1 Mounting NPB GPRS H option card on a WEBs controller 1 Remove power fro
Download Pdf Manuals
Related Search