700 TVL IR Vandal Proof Analog Dome Camera User`s Manual
Contents
1. Heavy stress violent vibration or water splash are not allowed during transportation storage and installation 3 Installation Do not apply power to the camera before completing installation Please install the proper power cut off device during the installation connection Always follow the instruction guide the manufacturer recommended If this product is installed in the ceiling please make sure the installation position can sustain the min 50N 4 Qualified engineers needed All the examination and repair work should be done by the qualified service engineers We are not liable for any problems caused by unauthorized modifications or attempted repair 5 Environment This series camera should be installed in a cool dry place away from direct sunlight or strong light inflammable explosive substances and etc The working temperature ranges from 30 C to 60 C Please keep it away from the electromagnetic radiation object and environment Please keep the sound ventilation Do not allow the water and other liquid falling into the camera 6 Accessories Be sure to use all the accessories recommended by manufacturer Before installation please open the package and check all the components are included Contact your local retailer ASAP if something is broken in your package 7 Daily Maintenance Please shut down the device and then unplug the power cable before you begin daily maintenance work iii Use the dry s2. a Power input port Connect to the DC 12V power to input the power RS 485 port Connect to devices such as DVR keyboard to realize remote control via this port 10 BNC port is to output analog video signal ideo output port You can connect to the devices such as the DVR or the NVR 3 Installation The dome camera usually mainly uses the in ceiling installation Important Please make sure the installation surface can min support the 3X weight of the camera and the bracket A1 Inner Hexagonal Wrench E A2 Inner Hexagon Screws Figure 3 1 P Inner Hexagonal Wrench Figure 3 2 C1 Ceiling or Wall C2 Expansion Bolt C3 Self tapping i i i Screw C4 Inner Hexagonal Wrench Transparent C5 Inner Hexagonal Enclosure Wrench Figure 3 3 Please Turn the Lens to the Proper Position D1 Inner Hexagonal M Wrench D3 Trip Bolt 4 D2 Lens Silicon Rubber Gasket D4 X Y Z Rotation Module Important When you are turning the lens X Y Z axis please make sure you have not touch the lens which may result in the camera low performance Figure 3 4 Step 1 Use the inner hexagonal wrench provided to loose the three inner hexagon screws in the dome cover and then open the cover See Figure 3 1 Step 2 Use the inner hexagonal wrench provided to loose the three inner hexagon screws in the dome and then remove the device installation pedestal See Figure 3 2 Step 3 Take out the inst
3. camera to switch to the color Here we recommend the default value If the system switches back and forth when you are using please set the value in night day mode larger and the value in the day night mode smaller CAMERA ID CAMERA ID 0001 ABCDEFGHIJKLMNOPQRSTUV WXYZ0123456789 9 90 O_ Yi 3 2529 N x47 CHR1 CHR2 c4 CLR POS J RETURN CHR1 Library 1 CHR2 Library 2 41 Select the character you want to modify CLR Clear current character POS Select it to go to the camera mask position interface 9 The parameter includes English French German Russian Portuguese Spanish Chinese and Japanese The default setup is English Important After you completed the setup please click the SAVE ALL button to save current setup and then exit the menu It is to guarantee the camera setup after the power failure 12 Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Component Device Construction Material Packing Com O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T11363 2006 standard X Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ T11363 2006 standard During the environmental friendly use per
4. 700 TVL IR Vandal Proof Analog Dome Camera User s Manual Version 1 0 0 Table of Contents 1 General INITOAUCLION tetuer 1 1 1 TN FAU THAT EN NR EN 1 1 2 IP RF WT SN FF FU RHAN RH RR FFF NN YR 1 1 3 FUNCIONS tere 1 1 4 Y RH HN EF I FE WY EFA 2 2 FAN OR er eee 5 2 1 DIMENSIONS marissa a 5 2 2 ee 5 3 THE 7 Z BD E T RM OSEE E 11 4 1 Ni a AN LL 1a M lE 11 4 2 Ed 1 Appendix Toxic or Hazardous Materials or Elements sese 13 Welcome Thank you for purchasing our analog camera This user s manual is designed to be a reference tool for your system Please read the following safeguard and warnings carefully before you use this series product Please keep this user s manual well for future reference 11 Important Safeguards and Warnings 1 Electrical safety All installation and operation here should conform to your local electrical safety codes The power shall conform to the requirement in the SELV Safety Extra Low Voltage and the Limited power source is rated 12V DC 24V AC in the IEC60950 1 We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation 2 Transportation security
5. Menu List Please refer to the following sheet for menu information THE 1 MENU THE2 MENU TYPE DC VIDEO ee AO AUTO LENSO _ THE 1 THET MENU THE 2 THE27MENU CONTRAST SPEED SES WE LUMINANCE MODE SHUTTER AUTO IRIS MAN MANUAL BLOCK J AUTO IRIS DISPLAY ON OFF SET AUTO BRIGHTNESS 0 255 MEIN MONITOR ON SHUTTER LOW saa OFF AGC LUMINANCE MODE AUTO GAIN OFF BRIGHTNESS x0 25 x1 00 SHUTTER 1 50 1 10 000 EE AREA SEL mo Juserte Roan 10 255 000 288 Jo B GAIN 000 288 PRIVACY 4 RIGHT 000 468 COLOR TRANSPARENT 00 1 00 ON tan BURST OFF DELAY PAUSE DAY NIGHT 000 255 NIGHT DAY amp O 000 255 ON OFF Y C Y C Y LEVEL 000 015 C LEVEL 000 015 ANTI CR PUW 1 PUSH toc 1 DELAY CNT ATW FRAME ATWa x0 50 x2 00 ENVIRON INDOOR MENT OUTDOOR og o f BACKLIGH gig Lacu NN AREE BALANCE WHITE CAMERA LUMINANCE MIDDLE HIGH MIRROR MEN OFF A 0 256 ADJUST xs Sae CAMERA RESET 4 2 Menu Note D The different series products support various lens Please refer to the specifications for detailed information 11 The user2 setup is the same with the user1 Q6 In day night mode the smaller the value is and the hard for the camera to switch to the black and white mode In night day mode the larger the value is and the hard for the
6. R EX ATR Adaptive Tone curve Reproduction function allows the camera to digitally calculate the video color again and then adjust the brightness to enhance the video quality This function can effectively enhance the color and black zone of the video when there is sharp light contrast in the environments General Camera ATR Camera IR function This series product can use the IR light to allow you to see the object or realize the monitor in the low illumination environment General Camera IR Camera 1 4 Specifications Please refer to the following sheet for specification 700 TVL IR Vandal Proof Dome Camera CA DBW480BP N A CA DBW481BP N A Video Processor 1 3 SONY EXview HAD CCD II Video Format PAL NTSC PAL 976 H 582 V NTSC Effective Pixel x494 V 976 H Color 0 005Lux F1 4 COLux IR light on Electronic Shutter PAL Auto 1 50s 1 100 000s Manual 1 50s 1 120s 1 250s 1 500 1 1000s 1 2000s 1 4000s 1 10 000s NTSC Auto 1 60s 1 100 000s Manual 1 60s 1 100s 1 250s 1 500 1 1000s 1 2000s 1 4000s 1 10 000s Lens Type 014 port 2 8 12mm zoom auto aperture lens andq14 port 4 9mm zoom auto aperture lens Day Night Switch Video Output 1Vp p Composite Output 75 Ohm BNC Above 65 dB AGC OFF OSD Menu Control Support LENS Auto Manual SHUTTER AGC Auto Manual BACKLIGHT Off BLC HLC High light compensation ma O WHITE ATW ANTI CR manual push lock push user 1 user 2 U
7. S DAY NIGHT Auto black and white color MODE PICTURE Mirror brightness contrast sharpness hue gain ADJUST Off luminance contrast MOTION Detect sensitivity block display area selection PRIVACY Area selection color transparent mosaic m T m Level Y level C level Character position English Japanese and etc Communication Port 5c 4a5 Protection Level Working Temperature 30 C 460 C IER A series product support AC24V 10 DC12V 10 Power DIOD Weight 980g A 1000g 2 Framework 2 1 Dimensions Please refer to the following figure for the dimension information The unit is mm See Figure 2 1 118 5 Figure 2 1 2 2 Structure Please refer to the following figure for detailed information See Figure 2 2 6 OK 6 Left Right Down 6 2 Figure 2 2 Please refer to the following sheet for detailed information Component Function Name Device lens 2 IR Light It is to send out the IR compensation light to enhance the night vision Component Function Dome internal Enclosure 4 X Y Z axis X Y Z axis module to realize 360 monitor module 5 Dome camera enclosure Dome camera pedestal These five buttons are for OSD menu operation 5 direction Please use the up down button to select the item and use buttons the left right button to select the option The button in the middle is to confirm current operation
8. allation location map from the accessories bag and then paste it on the ceiling or the wall to identify the installation area Draw out the cable exit and four plastic expansion bolt holes in the installation position according to the device pedestal Dig the four plastic expansion bolt holes and cable exit Insert the four plastic expansion bolts into the screw holes oee Figure 3 3 Step 4 Adjust the device installation pedestal to the proper position and then draw the cable through the cable exit you just dug in the ceiling wall Line up the four screw holes in the device pedestal to the four plastic expansion bolt holes in the installation position Put the four self tapping screws in the four plastic expansion bolts firmly See Figure 3 4 Step 5 Adjust the device position and then line up the three inner hexagon screws of the device to the three holes in the installation ceiling wall Put the three inner hexagon screws to the screw holes of the device pedestal and then use the inner hexagonal wrench to secure firmly Step 6 Loose the trip bolt and then turn the X Y Z rotation module to adjust the camera lens to the proper monitor angle Step 7 Use the inner hexagonal wrench to secure three hex screws at the top cover to complete the installation Now you have completed dome camera installation and cable connection You can use the terminal devices such as the DVR NVS and etc to view the monitor video 10 4 Menu 4 1 Main
9. iod EFUP period the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these substances or elements will not result in any severe environmental pollution any bodily injury or damage to any assets The consumer is not authorized to process such kind of substances or elements please return to the corresponding local authorities to process according to your local government statutes Note e This manual is for reference only Slight difference may be found in the user interface e All the designs and software here are subject to change without prior written notice e f there is any uncertainty or controversy please refer to the final explanation of us e Please visit our website or contact your local service engineer for more information 13
10. oft cloth to clean the device If there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean the device Please put the dustproof cap to protect the CCD CMOS component when you do not use the camera 1V 1 General Introduction 1 1 Overview This series analog camera adopts the high sensitivity CCD and advanced circuit design It is featuring the high quality video the lowest distortion low noise and etc This series product is suitable to be used in surveillance system and video process system 1 2 Features e High performance SONY CCD high resolution 7OOTVL vivid and impressive video e Support auto white balance ANTI CR anti color roll manual control push lock and etc Restore high definition and vivid video e Support privacy mask function Set zone color transparent mosaic and etc Support motion detect function Set zone sensitivity block display and etc Support backlight compensation high light compensation close and etc according to the actual environments Support ATR digital WDR function Support auto electronic gain control self adaptive brightness Support OSD on screen display suitable for user self defined setup Support various languages such as English Support IR function Support RS 485 communication protocol 1 3 Functions High Definition TE 6 5 56 We RES g 10 ATR and AT
Download Pdf Manuals
Related Search