outside
Contents
1. 10 mm Important Read these instructions carefully before installing operating servicing or repairing this tool Keep these instructions in a safe accessible place Product Type 3 AIR POLISHING KIT lt Pneumatic Tool Company www astrotools com 1 YEAR LIMITED WARRANTY Astro Pneumatic Tool Co warrants our products to the original user against defective material or workmanship for a period of 1 year from the date of 1st use Astro reserves the right to determine whether the product failed because of defective material workmanship or other causes and to charge back for missing parts Astro Pneumatic Tool Co at its discretion will repair products covered under this warranty free of charge The original user is to return the product with the exceptions listed below with the distributor s name address adequate proof of date of purchase or a copy of warranty card and a short note explaining the problem Failures caused by accident alteration or misuse are not covered by this warranty elf one part of this product fails please do not return the entire product Astro will replace free of charge component parts of this product that fail within 1 year of first use by the original user Items included in this category include but are not limited to kits hand tool kits and any other product where there are multiple items or components that make up the unit Please contact the phone number below in order to obtain the rep2. Trigger 3043 10 Washer 3043 11 Ball Bearing 12 3043 12 Front End Plate 13 3043 13 Rotor 14 3043 14 Rotor Blade 4 7 26 3042 26 Pin 27 3042 27 Inlet Bushing 28 3043 28 Wrench Housing Sleeve 30 3042 30 Spring 1 2 3 4 A 5 7 P 0 11 oo or lt Aj Page 4
3. can be obtained at www oehha ca gov under Propositon 65 In order to reduce their exposure to such chemicals users should always work in well ventilated areas wear appropriate safety equipment and clothes that are specifically designed to filter out microscopic particles Page 2 Astro Pneumatic Product Type Tool Company 3 AIR POLISHING KIT 372 Old US Highway 52 South Mount Airy NC 27030 PARTS BREAKDOWN Ee ey ee FOR 3055 3 Air Polishing Kit Parts List 3 Wool Buffing Pad 1 3 Polishing Foam Pa Yellow 1 3 Polishing Foam Pad White 1 Blow Molded Case 1 SUGGESTED AIR LINE CONNECTION All pipe and fittings Air regulator set at should be 1 2 or larger recommended working air pressure Filter Lubricator COMPRESSOR With sufficient capacity to maintain recommended working pressure at each tool outlet AIR TOOL Receiver tank 40 gallons or more Page 3 Astro Pneumatic Product Type e Tool Company 3 AIR POLISHING KIT 372 Old US Highway 52 South Mount Airy NC 27030 Call 1 800 221 9705 for questions concerning performance of the product PARTS BREAKDOWN or other inquiries FOR 3043 3 Mini Polisher Parts List Description Lock Nut Cylinder Clamp Nut Rear End Plate Bearing Housing Ball Bearing Ball Bearing Pin Ball Bearing Seal Housing i gt bt Description ak Washer Valve Stem Spacer g Planet Carrier g Pin Planet Gear Valve Bushing Internal Gear
4. Foreseen Use of the Tool Do not use the tool outside of the design intent Never modify the tool for any other purpose or for its use Safety Precaution Caution To help prevent personal injury e Normal use of this product is likely to expose the user to dust and or microscopic particles containing chemicals known to the State of California to cause cancer birth defects or other reproductive harm Always wear appropriate safety equipment and clothing when using this product Study understand and follow all instructions provided with this product Always wear ANSI approved goggles when using this product Always select the correct accessories of the correct size and design for the job that you are attempting to perform Always work in a clean safe well lit organized and adequately equipped area Do not begin repairs without assurance that vehicle is in secure position and will not move during repair Product Information e Blow molded case for easy storage and transport e Kit Includes 1 3 Mini Polisher Direct Drive 2 500rpm 3043 1 3 Sanding Polishing Back up Pad 20302P 1 3 Wool Buffing Pad 20303 1 3 Polishing Foam Pad Yellow 20306 1 3 Polishing Foam Pad White 20306W SPECIFICATIONS Tool Weight Overal Length Avg Air Consumption Recommended Air Pressure Minimun Hose Size 1 45 lbs 0 66 kg 5 1 2 ins 140 mm 5 cfm 140 l min 90 psi 6 3 bar 3 8 in
5. be chosen according to the material being worked upon Please consult provider of such devices 8 Release the start and stop device in case of failure of energy supply 9 Only use the lubricant recommended by the manufacturer Product Type 3 AIR POLISHING KIT WARNING A 1 The tool shall not be used in potentially explosive atmospheres 2 Disconnect the air hose before changing or adjusting any inserted tools 3 Before using tool please confirm all couplings and plugs are fixed securely Air hose that is under pressure may lash out whe disconnected and could lead to serious injuries 4 Prevent loose clothes long hair or any other personal accessor ies from coming close to moving parts to reduce the risk of being caught trapped or drawn into the rotating spindle 5 Excessive high air pressure that exceeds the maximum pressure may cause injuries to user 6 Exposure to strong vibration for extended time may cause harm to operator 7 Make sure of the rotation direction before starting the tool to reduce hazardous situations due to unexpected rotation direction 8 Slip Trip Fall is a major reason of serious injury or death Beware of excess hose left on the walking or work surface 9 Wearing eye face protector could reduce the danger to person from high speed splinters being emitted from the tool or work surface 10 Wearing correct breathing protection will help avoid inhaling dust or handling debris from wo
6. d to remove the dust on a daily basis 4 STORAGE Avoid storing the tool in a location subject to high humidity If the tool is left unused the residual moisture inside the tool can cause rust Before storing and after operation oil the tool at the air inlet with spindle oil and run it for a short period 5 DISPOSAL Follow national legislation of waste disposal Never drop into fire 6 ORDERING SERVICE PART For further operational and handling information or for replacement of parts and components contact the sales agent from where you purchased the tool or the service division of our company When ordering parts and components give each part number name and quantities Cautions for Use 1 This tool is intended for polishing and sanding with all types of movement e g rotary orbital and reciprocating using coated abrasive product and bonnets of various soft materials and endless belts Any other use is forbidden 2 Only use the polishing and sanding pads as recommended by the pad manufacturer 3 It is forbidden to use the grinding wheels and cut off wheels on this tool 4 Ensure the max operating speed of the pad is higher than the rated speed of the poser tool 5 Centrally adhere sanding disc to support pad 6 Always wear ANSI approved ear protection and safety glasses when using this tool Gloves and protective clothing are recommended 7 Personal protection and dust collection devices shall
7. lacement components covered under warranty Astro Pneumatic Tool Co or its authorized service representatives must perform all warranty repairs Any repair to the product by unauthorized service representatives voids this warranty The rights under this warranty are limited to the original user and may not be transferred to subsequent owners This warranty is in lieu of all other warranties expressed or implied including warranties of merchantability and fitness for a particular purpose Some states do not allow the exclusion of limitations of incidental or consequential damages so the above limitations may not apply to you All claims must be sent to Astro Pneumatic Tool Company 372 Old US Highway 52 South Mt Airy NC 27030 A PLEASE CALL 1 800 221 9705 A FOR REPAIR AND RETURN INSTRUCTIONS Unpacking When unpacking check the parts diagram and part number listing on pages 3 4 to make sure all parts are included If any parts are missing or damaged please call your distributor 3 AIR POLISHING KIT Page 1 MAINTENANCE INSTRUCTION 1 LUBRICATION Before connection the hose apply 4 to 5 drops of 60 spindle oil at the air inlet After 3 to 4 hours of operation oiling may be necessary again 2 TIGHTNESS OF PARTS Regularly check whether all connection parts are fastened securely Follow this procedure daily before beginning work 3 CLEANING Dust may accumulate around spindle inside shield It is recommende
8. rk process that can be harmful to your health 11 High sound level can cause permanent hearing loss Use hearing protection while operating tool 12 Due to the material being processed there may be a risk of explosion or fire Be aware of work surface dangers prior to beginning work 13 There is a risk of being cut due to high speed rotation Do not touch high speed rotating disc 14 This power tool is not insulated If contact is made with an electric current injury may occur 15 Dust created by sanding sawing grinding drilling and other related activities may expose the user to dust and or microscopic particles that may contain chemicals known to the State of California to cause cancer birth defects or other reproductive harm A WARNING A Users of this tool should review the chemical composition of the work surface and any products used in conjunction with this tool for any such chemicals prior to engaging in any activity that creates dust and or microscopic particles Users should obtain the Material Safety Data Sheets for all identified chemicals either from the manufacturer or their employer and proceed to study understand and follow all instructions and warnings for exposure to such chemicals Some examples of these chemicals are lead from lead based paints crystalline silica from bricks cement and other masonry products and arsenic and chromium from chemically treated lumber A listing of the chemicals
Download Pdf Manuals
Related Search
outside outside lands outside outside lands lineup outside agents outside lands 2025 outsiders cast outsiders movie outside tv outside magazine outside lands tickets outside in spanish outsiders book outside temperature outside lights outside life outsiders broadway outside lands 2025 lineup outside staind outside lands music festival outside enhypen outside 2024 outside watch outside calvin harris outside sports outside ir35