Photonic Satellite
Contents
1. Speed and temperature increase MP Therapeutic options With your Satellite you can select and irradiate geometric forms in order to treat the body in correct dimension fitting to the body part Additionally you can determine the speed of the movement of the beams By means of this innovative options you may apply more therapeutic effect If you want a more point orientated therapy slow down the speed this will bring more heat to the body in case you want less heat simply reduce the speed The supplied energy remains the same Temperatur an einem Punkt Temperature at low speed More heat because the laser remains a longer time on a point Temperatur an einem Punkt Temperature bat high speed Less heat because the laser moves faster from point to point point Care and maintenance Cleaning and disinfection Unplug the power cord of the Satellite unit before beginning all cleaning and care Please ensure that you do not use sharp or caustic agents e g acetone when cleaning the plastic parts Avoid getting moisture in the housing A damp cloth is the best cleaning tool To disinfect the device use a soft cloth that has been dampened with a mild DGHM appro ved DGHM Deutsche Gesellschaft fur Hygiene und Mikrobiologie German Hygiene and Microbiology Association disinfecting agent Always use a damp cloth for cleaning and disinfection never flush water over the device Do not use a solvent2. If you work with an applicator sterilise the applicator after each use in order to avoid transmitting infection to the patient Calibration and safety check Your Satellite does not contain internal parts or components that need to be serviced by the user Thus there is no reason to open the device housing In order to comply with the regulation EN 60825 1 Safety in laser facilities your Physiola ser Olympic unit along with all probes and accessories should be sent to the manufacturer for checking and recalibration no longer than one year after you begin to use it Please be aware that the annual safety check is mandatory and is legislatively prescri bed by the Medical Devices Act in Germany MPBetreibV 6 Please contact your retailer Technical description Technical Data Weight 4kg Transport and storage Relative humidity 30 bis 75 Laser Diodes Ix red 638 nm max 150 mW Continuons gt 10m 3 mrad beam CW LED Diodes Safety margin NOHD The distance at which the radiation strength or the radiation is equal to the corresponding limit for the maximum permissible radiation of the cornea MPE Maximum Permissible Exposure 11 Guarantee and disposal Guarantee The manufacturer s guarantee is valid for 24 months The manufacturer is only responsible for the features warranted by the user manual if the device has been operated carefully according to the user manu
3. Photonic Satellite Compact scanning device Operation manual LASER Introduction Your Physiolaser with the Photonic Satellite Two in one Thank you for choosing the Physiolaser including the Photonic Satellite the latest generati on high quality laser device from Reimers amp Janssen GmbH The RJ laser design is founded on over 28 years of experience in the development and pro duction of laser devices for medical therapy Our profound knowledge about complemen tary therapy methods are built into this product gentle laser therapy for a broad scope of applications The Physiolaser involves a base device with a microprocessor which can control all laser probes available from Reimers amp Janssen GmbH Thus the Physiolaser is the basis of our trend setting concept universal versatility with ease of operation Whether you are using surface probes single probes or laser needles with the efficient Phy siolaser you will always have the newest therapy program at your disposal With the easy to use touchscreen and the built in basic therapy set you can immediate ly proceed with treatment Every programme can be adapted for your individual therapy needs Furthermore you can purchase special therapy sets and easily install them into your Physiolaser Thus the Physiolaser Photonic Satellite is suitable for a wide range of treatments in der matology rheumatology orthopaedics physiotherapy sports medicine Th
4. al Readjustment calibration and maintenance or repairs should only be performed by the retailer otherwise the guarantee expires Any alterations or interventions on the device by an unauthorized third party void the guarantee The manufacturer guarantees replacement parts for a period of ten years after the date of purchase Disposal Probes and control units may not be disposed of along with normal electronic waste be cause of the radiation hazard The devices should be sent to the manufacturer for decom missioning and disposal Manufacturer Distributor EN ISO 13485 V 1 2 25 05 2012 Distributor REIMERS amp JANSSEN GmbH Photomedicine Laser Therapy Fabrikstr 22 79183 Waldkirch Germany Tel 49 7681 4934149 Fax 49 7681 4934149 service rj laser com www rj laser com Quality Management ISO 13485 2003 AC 2003
5. ase speed up Reset individual settings With Reset you can get back to the origi nal settings With Reset circle all individual settings will be deleted Start the therapy After all forms are selected start the thera py with the button Start Prior to the start of the laser beam a two signal beep will indicate that the laser now will be in use y situ You can Stop the start e g in case if some one forgot to waer goggles 7 4 With the button Start the laser beam will be activated with presetted power and time The therapy mode Prior to the therapy please wear protection goggles After the beep the theraapy screen appears with the treatment programs and all the set parameters During the therapy a short beep willbe an nounced every fifteen seconds The timer will count down to zero and the administe red amount of energy increases A long beep will be announced once the therapy time is reached The current treat Upper yellow part of the therapy screen ment can be aborted at any time by pressing shows the active laser with all settings Stop Lower part remains blue because no probe was connected During the treatment googles must be worn by staff and patients Only goggles that are marked according to EN 207 may be used The effective wavelength range of the filter lenses must include the wavelength of the Photonic 500 and connected probes
6. e focussed laser beam of the Photonic Satellite can directed as a point line or circilary Such forms can be changed easily to any larger area to be treated with optimal dosage Photonic 500 Two in one Static and movable forms On the Physioalser screen Select Form you can choose between stable fixed and three movable forms The fixed forms offer a circle a vertical ho rizontal line and apoint The movabale forms offer a filled circle oscillation a square the line moves up and down on an rectangle Once you tip to the form you will reach the screen Adjust Photonic where you can change the basic form and speed of the movement Please note that the form Point will generate heat and this can lead to overheating the skin especially pigmented skin Reduce the power and treatment duration On the screen Select Form you will find the fixed stable forms in the upper line and the movable forms in the lower line Change expansion On the screen Adjust Satellite you can change the amplitude size of all forms ex cept the point Witht he arrow buttosn you can change the size of the form for horizontal orvertical dimension For example you may change the circle to an ellypse The pilot beam lt 5mVV control lamps on top of the housing will be active during the setting The screen Adjsut Photonic with active amplitude function The circle was stret ched verticall
7. y Change position Move the position to different areas without moving the housing with the aaow buttons Reset will jump back to normal Active Position allows to move the form to laft or right Movable forms Movable forms can be adjusted in the amplitude position and speed press button Speed Please use the plus minus buttons to im crease or decraease the speed of the laser beam With t and the speed of the laser beam movement can be changed Turning knobs Instead of the arrow buttons you can adjsut all features with the turning knobs this is probably much faster and easy to do Once you have selected Amplitude or Position the knob will change vertical and horizontal axis In case the Speed is active the knobs offer the same function as above Left turn slows down and right turn increa The left button will change the form in re ses the speed gard to the Y axis and the right knob the X axis Function of arrow buttons turning knobs El X Achse EJ Active refers to left refers to right Vertical button Horizontal button Function knob knob Upper Left PP Turn right Turn left vertical stretch horizontal upsetting Amplitude Lower Right Trun left Turn right vertical upsetting horizontal stretch Upper increase Left PP Turn left Turn left slow down Speed lower Right Turn righ Turn right decre
Download Pdf Manuals
Related Search