60007 MANUAL (tri).qxd
Contents
1. they NOT safety glasses 10 SECURE WORK Use clamps or a vise to hold work when practical They are safer than using your hand and free both hands to operate tool 11 DON T OVERREACH Keep proper footing and balance at all times 12 MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for best and safest performance Follow instructions for lubricating and changing accessories 13 DISCONNECT TOOLS BEFORE SERVICING when changing accessories such as blades bits cutters etc 14 REDUCE THE RISK OF UNINTENTIONAL STARTINGMake sure switch is in OFF position before plugging in 15 USE RECOMMENDED ACCESSORIES Consult the owner s manual for recommended accessories The use of improper accessories may cause risk of injury 16 NEVER STAND ON TOOL Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted 17 CHECK DAMAGED PARTS Before further use of the tool a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function check for alignment of moving parts binding of moving parts breakage of parts mounting and any other conditions that may affect is operation A SAFETY GUIDELINES READ THIS OWNER S MANUAL COMPLETELY AND MAKE SURE YOU UNDERSTAND ALL OF ITS SAFETY GUIDELINES le Se fy NS 10 11 12 13 Keep your workspace clear and free of all debris Make sure the saw is in the OFF position b2. B GROUNDED OUTLET BOX permanent ground such as a properly grounded outlet Ta box 5P CO GROUNDING ADAPTER C WARNING FOR YOUR OWN SAFETY READ INSTRUCTION MANUAL BEFORE OPERATING SAW e Wear eye protection e Use splash hood for every operation for which it can be used e Disconnect saw before servicing when changing cutting wheels and cleaning e Use tool only with smooth edge cutting wheels free of openings and grooves e Replace damaged cutting wheel before operating e Do not fill water bath above water fill line USE PROPER EXTENSION CORD Make sure your extension cord is in good condition When using an extension cord be sure to use a cord heavy enough to carry the current your product will draw An undersized cord will cause a drop in line voltage resulting in loss power and overheating Table below shows the correct size to use depending on cord length and nameplate ampere rating If in doubt use the next heavier gauge The smaller the gauge number the heavier the cord MINIMUM GAUGE FOR CORD 18 AWG 16 AWG 16 AWG 14 AWG TOTAL LENGTH OF CORD IN FEET 25 50 100 150 STATE OF THE ART FEATURES HP motor 4 000 RPM ELECTRICAL MOTOR SPECIFICATIONS e Horsepower H P Saw duty rated e Automatic thermal overload protection protects saw e Volts 115V from power surges and motor overheating e Amps 5 8 e Specially designed mounting provides easy blade e RPM 4 000 change e Cycle 60 e Phase 1 Fiberglass impregna
3. LEA EL MANUAL DE OPERACI N COMPLETAMENTE Y ASEGURESE QUE ENTIENDE TODAS LAS PAUTAS DE SEGURIDAD 1 Mantenga su area de trabajo limpio y libre de escombros Verifique que la sierra este apagada antes de enchufarla No deje la sierra sola mientras este encendida Apague la sierra cuando no la este usando e wN Siempre utilize gafas protectoras mascara para polvo y proteccion para los oidos cuando este operando la sierra para cumplir conlas normas ANSI Z87 1 Mantengase alerta cuando este usando la sierra El no prestar la debida atencion puede ocasionar heridas graves Desconecte la unidad de la electricidad antes de instalar o cambiar cuchillas y antes de lipiarla o darle servicio Mantenga la sierra limpia y en buen estado para lograr el mayor y mas seguro rendimiento en cada trabajo Na tu Ensure that a continuous flow of water to both sides of blade during operation 9 Do not cut dry with blades designed for wet cut 10 No introduzca material a la fuerza Degje que la cuchilla corte a su propia velocidad 11 Mantenga el resguardo hacia abajo mientras use la sierra 12 Asegurese que utilize la cuchilla o rodaja apropiada para el trabajo que este haciendo No use la herramienta para efectuar trabajo para efectuar trabajo para el cual no fue disenada 13 Esta sierra esta equipada con un enchufe de tres puntas No altere el enchufe ni lo conecte en un receptor de dos puntas 15 ELECTRICAL REQUIREMENTS This too
4. Motor Specifications 5 Sp cifications lectrique Especificaciones para el Motor Unpacking Assembly amp Set Up wS amp Moteur sssssssssssesesssssssosssssssssenen 11 BIB CHICO seciusddeatees ee 17 Cutting Head Assembly Installations D ballage et Assemblage 11 Desempaque et Montaje 17 Blade amp Blade Guard Installation 6 Assemblage de la T te de Coupe 11 Instalacion Cutting Head 17 Water Pump Installation 6 Installation du Disque et Instalacion de la Cuchilla 18 Water Pump Safety Guidelines 6 Protection de Disque 12 Instalacion de la Bomba de Agua 18 Cutting Table Pete EEE eC EGINE 6 installation de la Pompe Eau 12 Pautas de Seguridad para Saw Operation 7 Directives de S curit pour la la Bomba de Agua sssceseeseesees 18 Saw Maintenance mener 7 Pompe Eau La Mesa de Cortar 18 Do s amp Dont s for Diamond Blades 7 Table de COUP mes Operaci n de la Sierra 19 Diagram of Wet Saw 8 Proc dures d Utilisation 7 Mantenimiento de la Sierra 19 Parts LIST aus 8 Entretien de laScie o Do s amp Dont s for Diamond Blades 19 Faire et Ne Pas Faire 13 Vista de la Sierra 20 Diagramme de la Scie 14 Lista de PATES ns 20 Liste de Pi ces 14 LIMITED WARRANTY This product is covered by a 30 day warranty from the date of purchase If the product is defective in workmanship
5. before attempting to cut any material Make sure your material is positioned properly on the saw table before beginning your cut Feed your material slowly into the blade DO NOT force material The blade will cut smoother and faster if these steps are followed ALWAYS practice SAFETY FIRST Wear eye safety goggles a dust mask and gloves when operating this saw Discard cracked bent chipped or damaged blades SAW MAINTENANCE WARNING DO NOT SERVICE CLEAN OR MAINTAIN THE SAW WITHOUT FIRST TURNING OFF THE MOTOR AND UNPLUGGING THE SAW FROM ITS POWER SOURCE FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY TO THE OPERATOR 1 NS A oP YN For longest life and best performance clean the saw after every use Wipe off all exterior surfaces and keep the cutting table clean and free to tile chips and debris Wipe off both the guide bars and the rollers on the cutting table Place light machine oil on the guide bar to facilitate smooth travel of the linear guide assembly The guide bars are specially treated to give you years of operation Always check the blade for cracks or signs of fatigue DOs amp DON Ts FOR DIAMOND BLADES DOs 1 Inspect blades daily for cracks or uneven wear Discard cracked chipped or bent blades 2 Always use manufacturer s recommendation for matching the right blade with the right material being cut 3 Inspect the arbor shaft for uneven wear before mounting the blade 4 Always use blades with the co
6. de l utilisateur e Guide de refend pour couper en 45 et 90 degr s e Couper les carreaux jusqu 16 pouces de diam tre et les carreaux de 10 pouces en diagonale e Portabilit et facilit d emploi e L ger nettoyage et entretien facile INSTRUCTIONS DE D BALLAGE ASSEMBLAGE ET MONTAGE ATTENTION AVANT DE BRANCHER LA SCIE UNE SOURCE D ALIMENTATION LECTRIQUE SUIVEZ LES INSTRUCTIONS D ASSEMBLAGE ET D INSTALLATION a _ Ouvrir le colis avec pr caution puis enlevez toutes les pi ces de la scie et tous les mat riaux d emballage V rifier que chaque article aille t coch sur la liste la page avant de jeter la caisse et les mat riaux d emballage Le contenu est la suivante e T te de Coupe e Guide de Refend 45 90 e Clef e Disque de 7 pouces e Bac a Eau en Plastique e Manuel d Utilisation e Protection de Disque Impr gn de Fibre de Verre Les pages suivantes explique tape par tape l utilisation des diff rentes composantes et le fonctionnement de la scie Avant toute mise en service il est n cessaire de lire ces instructions e Pompe Eau e Moteur ASSEMBLAGE DE LA TETE DE COUPE ATTENTION AVANT DE BRANCHER LA SCIE UNE SOURCE D ALIMENTATION LECTRIQUE SUIVEZ LES INSTRUCTIONS D ASSEMBLAGE ET D INSTALLATION 1 Enlever le support du moteur et le moteur de l emballage D visser les vises avec ailes Se Ss assez afin de permettre le support du moteur d entrer dans
7. eau afin que le niveau d eau soit au dessus de la buse de 7 consommation i Maintenir le cordon lectrique hors de l eau et branchez le dans une prise trois broches l arri re de la t te de coupe Utiliser l interrupteur d ON OFF du moteur afin de mettre la pompe en marche POMPE EAU SONT INDIQU ES EN BAS VEUILLEZ LES LIRES ILLUSTRATION 3 CET DIRECTIVES DE S CURIT POUR LA POMPE EAU 1 TABLE DE COUPE GRADU E EN POUCES ET EN CENTIMOTRES AFIN D EFFECTUER DES COUPES AUX DIMENSIONS PR CISES TAPES DE POSITIONNEMENT DU GUIDE DE REFEND 45 90 DEGR S le 4 La pompe est quip e avec une fiche mise la masse Assurer de brancher la fiche une prise lectrique correctement mise la masse afin de r duire le risque de choc lectrique Pendant l assemblage et l installation du syst me de pompe d eau assurer de supporter compl tement la pompe et la tuyauterie afin de r duire les dommages et les pannes de la pompe Ne jamais manipuler la pompe par le fil d alimentation avec les mains mouill es ou debout sur une surface mouill e Ne jamais utiliser la pompe pour pomper autre chose que de l eau ou d autres liquides compatibles Ne jamis l utiliser pour pomper de la gazoline du k ros ne ou d autres liquides combustibles ou corrosifs Si la pompe fait d faut toujours la d branchez de sa source de courant avant de la manipuler ou d essayer de la d boucher ou d effectuer quelconqu entret
8. est quip e d un c ble lectrique avec trois broches Ne jamais modifier le c ble 9 BESOINS LECTRIQUES BRANCHEMENT Pour prot ger l utilisateur contre toute possibilit et risque d lectrocution cet outil doit tre branch dans une prise reli e la terre e Dans le cas de mauvais fonctionnement ou de panne le raccordement la terre fournit un chemin de moindre r sistance au courant lectrique et r duit le risque de choc lectrique Cet outil est quip d une c ble lectrique avec fil et fiche de raccordement la terre Le branchement de la fiche doit tre ce correspondante correctement install et reli e la terre conform ment aux r gles et ordonnances locales e Si la fiche fournie n entre pas correctement dans votre prise faites en poser une autre par un lectricien qualifi e Une connexion incorrecte du fil de terre peut cr er un risque d lectrocution Le fil de terre est isol Il est de couleur verte avec ou sans rayures jaunes Si vous devez r parer ou remplacer le c ble ou la fiche de raccordement ne reliez pas le fil de terre une borne positive e Si vous ne comprenez pas parfaitement les directives de raccordement la terre ou si vous avez un doute de ce raccordement pour votre outil v rifiez aupr s d un lectricien ou d un employ de maintenance qualifi e Utiliser que les rallonges 3 fils avec fiche m le 3 broches avec terre et fiche femelle et 3 p
9. grounding plug The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances Do not modify the plug provided if it will not fit the outlet Have the proper outlet installed by a qualified electrician Improper connection of the equipment grounding conductor can result in a risk of electric shock The conductor with insulation that is green on the outside with or without yellow stripes is the equipment grounding conductor If repair or replacement of the electric cord or plug is necessary do not connect the equipment grounding conductor to live terminal Check with a qualified electrician or service personnel if the grounding instructions are not completely understood or if in doubt as to whether the tool is properly grounded Use only 3 wire extension cords that have 3 prong grounding plugs and 3 pole receptacles that accept the tool s plug Repair or replace damaged or worn cord immediately To avoid the possibility of the appliance plug or receptacle getting wet position tile saw to one side of a wall mounted receptacle to prevent water from dripping onto the receptacle or plug The user should arrange a drip loop in the cord connecting the saw to a receptacle The drip loop is that part of the cord below the level of the receptacle or the connector if an extension cord is used to prevent water from traveling along the cord and coming in contact with
10. les correspondant la fiche de votre outil e R parer ou remplacer les rallonges lectriques endommag es imm diatement e Pour viter de mouiller la fiche de l outil ou la prise de courant branchez la scie une prise murale situ e de c t Pour emp cher l eau de p n trer dans la prise ou la fiche laissez le c ble de branchement pendre en boucle entre la scie et la prise Cette boucle doit se situer sur une partie duc ble plus basse que la prise ou le raccord si vous utilisez une rallonge et emp cher l eau qui coule le long du c ble d atteindre la prise e Si la fiche ou la prise sont accidentellement mouill es ne d branchez pas le c ble D connecter d abord le fusible ou le disjoncteur du circuit d alimentation puis d branchez votre outil et v rifiez alors seulement s il y a de l eau dans la prise e Utiliser que les rallonges lectriques class es UL e L utilisation des rallonges lectriques de capacit s insuffisantes provoque une baisse de tension ou une perte de puissance entra nant une surchauffe du moteur Assurer que votre rallonge lectrique tol re le courant n cessaire l alimentation de votre appareil e Lorsque vous d branchez le c ble ne touchez jamais une prise de courant ou les fiches m les e Une connexion incorrecte du fil de terre peut cr er un risque d lectrocution plus particuli rement lorsque l outil est utilis aux endroits humides ou pr s de la tuyauterie Cet
11. of operation Always check the blade for cracks or signs of fatigue DOs amp DON Ts FOR DIAMOND BLADES DOs 1 Inspect blades daily for cracks or uneven wear Discard cracked chipped or bent blades 2 Always use manufacturer s recommendation for matching the right blade with the right material being cut 3 Inspect the arbor shaft for uneven wear before mounting the blade 4 Always use blades with the correct arbor size on a compatible arbor shaft 5 Ensure the blade is mounted with the rotation arrow in the proper direction and is securely tightened with the wrench 6 Always wear the proper safety equipment at all times when operating the saw Wear goggles and dust mask at all times when operating saw 7 Periodically check the blade for cracks or bond fatigue 8 Always have a continuous flow of water on both sides of the blade before cutting any material DON Ts 1 Do not operate the saw without all safety guards in position 2 Do not operate the saw with blades larger or smaller than 7 3 Do not cut dry with blades marked Use Wet 4 Do not exceed maximum RPMs recommended by the blade manufacturer 5 Do not force the material into the blade Let the blade cut at its own speed 6 Do not cut material not recommended by the blade manufacturer PA 19 VISTA DE LA SIERRA DESCRIPTION Water Tray Assembly Frame Assembly Roller Guide Bar 60007 45 90 Rip Guide SIERRA PARA AGUA DE 7 4570 Fip
12. the receptacle If the plug or receptacle does get wet don t unplug the cord Disconnect the fuse or circuit breaker that supplies power to the tool Then unplug and examine for presence of water in the receptacle Only UL listed extension cords should be used with this product e Improper use of extension cords may cause inefficient operation of your tool which can result in overheating Be sure your extension cord is rated to allow sufficient current flow to the motor For the proper gauge for your tool please see chart Do not let your fingers touch the terminals of plug when installing or removing the plug to or from the outlet If not properly grounded this power tool can incur the potential hazard of electrical shock particularly when used in damp locations or in proximity to plumbing If an electrical shock occurs there is the potential of a secondary hazard such as your hands contacting the grinder tool This tool is intended for use on a circuit that has an outlet METAL SCREW that looks like the one illustrated in Figure A The tool has a grounding plug that looks like the plug illustrated in Figure A A temporary adapter which looks like the adapter illustrated in Figure B and C may be used to connect this plug to a 2 pole receptacle as shown in Figure B if a properly grounded outlet can be installed by a qualified electrician The green colored rigid prongs extending from the adapter must be connected to a
13. 7 WET SAW OWNER S MANUAL A N D PARTS LIST SCIE a EAU de 7 pouces MANUEL D UTILISATION ET LISTE DE PIECES SIERRA PARA AGUA de 7 E OPERACION LISTA DE PARTES Model 60007 Modele 60007 Articulo 60007 CAUTION Read and follow all safety and Operating instructions before using this saw PRECAUTION Lire et suivre toutes les directives de s curit et d op ration avant d utiliser cette scie iAVISO Lea y siga todas las instrucciones de funcionamiento y seguridad antes de usar esta sierra Q EP CO INC ROBERTS CONSOLIDATED INDUSTRIES INC ROBERTS CO CANADA LTD 1081 Holland Drive 600 N Baldwin Park Blvd 2070 Steeles Ave Boca Raton FL USA 33487 City of Industry CA USA 91749 Bramalea ON CANADA L6T 1A7 561 994 5550 Fax 561 241 2830 626 369 7311 Fax 626 369 6191 905 791 4444 Fax 905 791 1998 www qep com TABLE OF CONTENTS TABLE DES MATI RES TABLA DE CONTENIDO Safety Instructions for Wet Saw 3 R gles de S curit pour la Scie 9 Pautas de Seguridad para Sierra 15 Safety Guidelines 3 Directives de S curit 9 Pautas de Seguridad 15 Electrical Requirements 4 Besoins lectriques scscsccseeeeees 10 Electrical Requirements 16 Warning e 5 Mise en Garde essesecsecseeeeses WY AN SR 17 State of the Art Features Pihemtrantessee 5 Caract ristiques 11 Caracteristicas de la Sierra 17 Electrical
14. ESPANOL ESPANOL in Figure A A temporary adapter which looks like the NV ra adapter illustrated in Figure B and C may be used to AT connect this plug to a 2 pole receptacle as shown in Figure B if a properly grounded outlet can be installed B GROUNDED OUTLET BOX by a qualified electrician The green colored rigid prongs ESPANOL extending from the adapter must be connected to a ee permanent ground such as a properly grounded outlet ai GROUNDING ADAPTER box ESPA OL f s AVISO FOR YOUR OWN SAFETY READ INSTRUCTION MANUAL BEFORE OPERATING SAW e Wear eye protection e Use splash hood for every operation for which it can be used e Disconnect saw before servicing when changing cutting wheels and cleaning e Use tool only with smooth edge cutting wheels free of openings and grooves e Replace damaged cutting wheel before operating e Do not fill water bath above water fill line USE PROPER EXTENSION CORD Make sure your extension cord is in good condition When using an extension cord be sure to use a cord heavy enough to carry the current your product will draw An undersized cord will cause a drop in line voltage resulting in loss power and overheating Table below shows the correct size to use depending on cord length and nameplate ampere rating If in doubt use the next heavier gauge The smaller the gauge number the heavier the cord MINIMUM GAGE FOR CORD 18 AWG 16 AWG 16 AWG 14 AWG TOTAL LENGTH OF C
15. Guide Adjustment LISTA DE PARTES Angle Bar Rollers Set Metal Bushing Set of 12 Angle Grinder Wing Screw Blade Guard 161 He Blade Lock Nut jt t Outer Flange Fm gt Blade x Inner Flange 181 p Go a a Water Flow L oe Y Cover for Automatic Overload oy 12 Switch z a i Le a Electrical Cord h 3 14 Electrical Cord Fixed Head Automatic Overload Switch a a z x Single Socket Bottom Plate Me Water Pump m k m tu 24 20 ji Blade Guard Adjustment Knob
16. ORD IN FEET 25 50 100 150 STATE OF THE ART FEATURES HP motor 4 000 RPM e Automatic thermal overload protection protects saw from power surges and motor overheating Specially designed mounting provides easy blade change Fiberglass impregnated plastic water tray withstands even the toughest punishment Easy to remove and install The adjustable rip guide allows both 90 and 45 cuts Rip cut up to 16 square tiles and diagonal cut up to 10 tiles Easily removable for cleaning and transportation Lightweight for easy setup and maintenance ESPECIFICACIONES ELECTRICAS DEL MOTOR e Caballos de fuerza H P e Voltios 115V e Amps 5 8 e RPM 4 000 e Ciclo 60 e Phase 1 e Conecte la sierra tan cerca como sea posible del enchufe EXTENSION CORDS When using an extension cord ensure all cords are no smaller than 12 gauge rated at a 20 AMP minimum and equipped with 3 prong plugs Use of anything smaller may result in overheating or burn out of the motor It is recommended to have an electrician check the voltage at the saw motor to ensure proper voltage to run the saw efficiently and safely DESEMPAQUE Y MONTAIE AVISO SIGA TODAS LAS INSTRUCCIONES PARA LA INSTALACION Y MONTAJE COMPLETAMENTE ANTES DE ENCHUFAR LA SIERRA O ENCENDER EL MOTOR Abra la caja cuidadosamente y remueva todos los componentes de la sierra y el material de empaque Asegurese de verificar todos los componentes con la vista de la sierra que se muestr
17. Plate Water Pump REGLES DE S CURI PRATIQUES POUR LA SCIE EAU LIRE ENTI REMENT CE MANUEL D UTILISATION ET ASSUREZ DE BIEN COMPRENDRE TOUTES LES DIRECTIVES DE SECURITE 1 2 10 14 12 13 14 15 16 17 18 LAISSER LES ACCESSOIRES DE PROTECTION EN PLAtien tat de marche ENLEVER LES CL S DE R GLAGPrenez l habitude de v rifier si elles sont bien enlev es avant de faire d marrer la scie GARDER VOTRE ESPACE DE TRAVAIL PROPRkes accidents sont souvent dus des endroits encombr s et au fouillis sur un tabli NE PAS TRAVAILLER DANS UN ENVIRONNEMENT RISQUES viter d utiliser un outillage lectrique dans les endroits humides ou mouilles et encore moins dans la pluie clairer bien votre espace de travail NE PAS LAISSER LES ENFANTS S APPROCHWieux vaut maintenir les visiteurs suffisamment l cart de votre zone de travail QUIPER VOTRE ATELIER DE PROTECTIONS POUR LES ENFANTSadenas interrupteurs principaux et pensez enlever les cl s de contacts des appareils T NE PAS FORCER L OUTIII fonctionnera mieux et il y aura moins de risques si vous l utilisez selon ses normes UTILISER QUE L OUTIL APPROPRI AU TRAVANE pas forcer avec l outil ou un accessoire a faire un travail pour lequel il n est pas con u PORTER DES V TEMENTS APPROPRI S viter de porter les v tements amples les cravates bagues bracelets ou bijoux qui risquent de s accro
18. WN and LOCKED position e The second switch is located on the motor mounting block enclosed in a protective housing This rocker switch has I and O markings Press the I to turn the switch ON This switch should be used as the primary ON OFF switch for saw operation Make sure that there is sufficient water in the water pan to cover the inlet on the water pump and that water is being supplied to the saw blade before attempting to cut any material Make sure your material is positioned properly on the saw table before beginning your cut Feed your material slowly into the blade DO NOT force material The blade will cut smoother and faster if these steps are followed ALWAYS practice SAFETY FIRST Wear eye safety goggles a dust mask and gloves when operating this saw Discard cracked bent chipped or damaged blades MANTIMIENTO DE LA SIERRA AVISO NO REPARE LIMPIE O DE MANTENIMIENTO A LA SIERRA SIN ANTES APAGAR EL MOTOR Y DESCONECTAR LA SIERRA EL NO HACER ESTO PUEDE RESULTAR EN HERIDAS GRAVES AL OPERADOR Dey we INS For longest life and best performance clean the saw after every use Wipe off all exterior surfaces and keep the cutting table clean and free to tile chips and debris Wipe off both the guide bars and the rollers on the cutting table Place light machine oil on the guide bar to facilitate smooth travel of the linear guide assembly The guide bars are specially treated to give you years
19. a en la pagina antes de e Cutting Head Assembly e Guia de 45 90 e Bomba de Agua e Motor e Llave e Cuchilla de 7 e Fiberglass Impregnated Water Tray e Manual de Operaci n e Resguardo de la Cuchilla Las siguientes paginas detallan la instalacion de los diferentes componentes paso por paso y el funcionamiento de la sierra Lealas cuidadosamente CUTTING HEAD ASSEMBLY INSTALLATION CAUTION FOLLOW ALL OF THE ASSEMBLY amp INSTALLATION INSTRUCTIONS COMPLETELY BEFORE CONNECTING THE SAW TO A POWER SOURCE OR TURNING THE MOTOR ON raw a LE amp SA 1 Remove the motor mount block and motor from the packaging loosen the wing pay screws enough to permit the motor mount to fit on the frame upright post IS 2 Set the motor mount block on the frame upright post then tighten the 2 wing screws to hold the motor block securely in place Diagrama 1 IE e gt lt NA R Fu DIAGRAMA 1 S323 17 INSTALACION DE LA CUCHILLA Y DEL RESGUARDO 2 3 SA Remove the blade guard and set it aside in the cutting head Raise the blade guard to the highest level and tighten the blade guard wing screw Then remove the blade shaft nut and outer flange Place the blade onto the shaft pushing it up against the inner flange Make sure the directional arrow is pointing in the direction of rotation Replace the outer flange and blade shaft nut With one hand hold the blade and tighten the blade shaft nut with your free h
20. ace or dust mask for commercial cutting operations Everyday eyeglasses only have impact resistant lenses they NOT safety glasses 10 SECURE WORK Use clamps or a vise to hold work when practical They are safer than using your hand and free both hands to operate tool 11 DON T OVERREACH Keep proper footing and balance at all times 12 MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for best and safest performance Follow instructions for lubricating and changing accessories 13 DISCONNECT TOOLS BEFORE SERVICING when changing accessories such as blades bits cutters etc 14 REDUCE THE RISK OF UNINTENTIONAL STARTINGMake sure switch is in OFF position before plugging in 15 USE RECOMMENDED ACCESSORIES Consult the owner s manual for recommended accessories The use of improper accessories may cause risk of injury 16 NEVER STAND ON TOOL Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted 17 CHECK DAMAGED PARTS Before further use of the tool a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function check for alignment of moving parts binding of moving parts breakage of parts mounting and any other conditions that may affect is operation A Ww O LON Mi PAUTAS DE SEGURIDAD PARA LA SIERRA PARA AGUA
21. and Make certain the nut is firmly tightened with wrench provided DO NOT OVERTIGHTEN Lower the blade guard into position and tighten the wing screw To remove the blade reverse the installation steps See Diagram 2 DIAGRAMA 2 INSTALACION DE LA BOMBA DE AGUA 1 Remove the water pump from its box and ensure that it is not cracked or damaged in any way See Diagram 3 Attach the end of the plastic tubing hanging down from the blade guard to the water pump nipple Place the water pump in the rear of the water tray on its side with the water pump nipple also on its side Next fill the water tray with the water so that its level is higher than the water intake nozzle Keep the power cord out of the water and plug it into the 3 prong receptacle on the back of the cutting head assembly The pump is activated by the ON OFF switch on the electric motor NOTE WATER PUMP SAFETY GUIDELINES amp MAINTENANCE INSTRUCTIONS ARE LISTED BELOW PLEASE READ CAREFULLY AND PAUTAS DE SEGURIDAD POUR LA BOMBA DE AGUA 1 LA MESA DE CORTAR LA MESA ESTA MARCADA EN PULGADAS PARA HACER CORTES DE DIMENSION FACILMENTE STEPS FOR POSITIONING 45 90 RIP GUIDE le 2 3 The pump is equipped with a grounding type attachment plug Be sure to connect the plug to a properly grounded grounding type receptacle to reduce the risk of electric shock When assembling amp installing the water pump system be sure to full
22. cher dans les l ments mobiles Il est recommand de porter des chaussures semelles antid rapantes Si vous avez des cheveux longs couvrez les pour les prot ger PORTER TOUJOURS DES LUNETTES DE S CURITLorsque le travail est poussi reux portez un masque Les lunettes normales sans verres anti choc ne sont pas protectrices BLOQUER VOTRE SCIE Utiliser les but es de votre tabli ou les pinces de mani re bloquer la scie plus pratique qu utiliser une main pour la retenir et vos deux mains sont libres pour travailler NE PAS UTILISER LA SCIE BOUTS DES Wieux vaut un bon appui stable lorsque vous travaillez ENTRETENIR SOIGNEUSEMENT VOS OUTILSVeuillez ce qu ils soient bien aff t s et propres pour bien travailler en s curit Respecter les instructions de graissage et de remplacement des accessoires D BRANCHER OUTILS AVANT DE LES NETTOYER de changer d accessoires de disques ect R DUIRE LES RISQUES DE D MARRAGE ACCIDENTEWE rifier que l interrupteur soit bien sur la position d OFF avant de le brancher UTILISER QUE LES ACCESSOIRES RECOMMAND n utilisant des accessoires inappropri s vous risquez de blesser quelqu un NE JAMAIS GRIMPER SUR UN OUTIL Vous risquez de vous blesser gravement s il bascule ou si vous heurtez accidentellement un objet tranchant V RIFIER LES L MENTS ENDOMMAG S Avant d utiliser votre outil v rifiez avec pr caution si une protection ou une autre pi ce endommag e fonctionne bi
23. directs Cette garantie est nulle si le produit ou ses l ments sont modifi s alt r s ou chang s de quelconque mani re ou si le produit est utilis d une mani re ou avec une lame qui n est pas recommand e par Q E P La pompe eau est exclue de cette garantie et est sujette la garantie de son fabricant Cette garantie remplace toute autre garantie explicite ou implicite IMPORTANT Afin de valider la garantie la fiche de garantie doit tre remplie et re ue dans un d lai de trente jours compter de la date d achat GARANTIA LIMITADA Este producto esta cubi rto por una garantia de un 30 dias desde la fecha de compra Q E P CO INC reparara y o reemplazara el producto sin costo al consumidor si el producto esta defectuoso en material o mano de obra y se devuelve al distribuidor en su empaque original Esta garantia NO CUBRE desgaste normal ni danos ausados por accidentes mal uso abuso o negligencia La responsabilidad de Q E P CO INC bajo esta garantia esta limitada la reparacion y o reemplazo del producto Q E P CO INC no sera responsable por danos resultantes Esta garantia quedara nula si el producto o algunos de sus componentes se modifican alteran o se cambian de alguna manera o si el producto se usa de una manera o con una cuchilla que no este recomendada por Q E P CO INC La bomba de agua queda excluida de esta garantia y esta sujeta a la garantia del fabricante Esta garantia reemplaza cualesquier otras
24. e end of the plastic tubing hanging down from the blade guard to the water pump nipple Place the water pump in the rear of the water tray on its side with the water pump nipple also on its side Next fill the water tray with the water so that its level is higher than the water intake nozzle Keep the power cord out of the water and plug it into the 3 prong receptacle on the back of the cutting head assembly The pump is activated by the ON OFF switch on the electric motor NOTE WATER PUMP SAFETY GUIDELINES amp MAINTENANCE INSTRUCTIONS ARE LISTED BELOW PLEASE READ CAREFULLY AND WATER PUMP SAFETY GUIDELINES 1 CUTTING TABLE MARKED IN INCHES AND CENTIMETERS FOR ACCURATE CUT DIMENSIONS STEPS FOR POSITIONING 45 90 RIP GUIDE 1 2 3 The pump is equipped with a grounding type attachment plug Be sure to connect the plug to a properly grounded grounding type receptacle to reduce the risk of electric shock When assembling amp installing the water pump system be sure to fully support the pump and piping to reduce the chance of pump failure or damage Never handle the pump by the cord with wet hands or when standing on a wet surface Do not use the pump to pump anything other than water or other compatible liquids Never use to pump gasoline kerosene or other combustible or corrosive liquids Should pump fail always disconnect from power source before handling pump or attempting to unclog or se
25. efore plugging it in Do not leave the saw unattended while it is running Always return the power to the OFF position Always wear safety goggles dust mask and ear protection when operating the saw to comply with ANSI Z87 1 Always remain alert when the saw is in use Inattention on the part of the operator may lead to serious injury Disconnect the unit from its power source before installing or changing blades and before cleaning or servicing the saw Keep the saw clean and maintained to achieve the safest and highest performance for every job Ensure that a continuous flow of water to both sides of blade during operation Do not cut dry with blades designed for wet cut Do not force the material being cut Always let the blade cut at its own speed Keep the blade guard in the DOWN position while operating the saw specification Make sure you use the correct blade or profile wheel for the job you are doing This saw is equipped with a 3 prong electrical plug Do not alter the plug or use a 2 prong receptacle ELECTRICAL REQUIREMENTS CONNECTING TOOL TO POWER SOURCE OUTLET This tool must be connected to a grounded power source while in use to protect the operator from electrical shock In the event of a malfunction or breakdown grounding provides a path of least resistance for electrical current to reduce the risk of electrical shock This tool is equipped with an electric cord having equipment grounding conductor and a
26. en comme pr vu V rifier l alignement des pi ces mobiles leurs fixations T DIRECTIVES DE S CURIT LIRE ENTIEREMENT CE MANUEL D UTILISATION ET ASSUREZ DE BIEN COMPRENDRE TOUTES LES DIRECTIVES DE S CURIT 1 Garder votre espace de travail propre et libre de d chets 2 V rifier si l interrupteur est sur la position d OFF avant de brancher votre outil 3 Ne jamais laisser un outil en marche L teigner apr s chaque usage 4 Toujours porter des lunettes de s curit un masque et de la protection pour les oreilles lorsque vous travaillez avec la machine 5 Rester vigilant lorsque vous travaillez L inattention peut provoquer de s rieuses blessures 6 D brancher vos outils avant de les nettoyer de changer d accessoires ou de disques 7 Nettoyer et effectuer l entretien la scie pour obtenir les meilleures performances pour chaque travail 8 Assurer qu il y a amplement d eau dans le bac a eau sur tous les deux cot s de disque lorsque vous travaillez avec l appareil 9 Ne pas couper sec avec les disques con us pour les coupes eau 10 Ne pas forcer le mat riel couper Laisser le disque couper sa propre vitesse 11 Laisser les accessoires de protection en place lorsque vous travaillez 12 Ne pas utiliser un disque de diam tre plus petit ou plus grand que la scie V rifier que vous utilisez un disque ou un roue profil con u pour le travail 13 La scie
27. garantias expresas o implicitas IMPORTANTE La tarjeta de garantia debera rellenarse y ser recibida por Q E P 30 dias despues de la compra para validar esta garantia SAFETY INSTRUCTIONS FOR WET SAW READ THIS OWNERS MANUAL COMPLETELY AND MAKE SURE YOU UNDERSTAND ALL OF ITS SAFETY GUIDELINES ils KEEP GUARDS IN PLACE and in working order 2 REMOVE ADJUSTING KEYS amp WRENCHES Form a habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on KEEP WORK AREA CLEAN Cluttered areas and benches invite accidents 4 DON T USE IN A DANGEROUS ENVIRONMENT Don t use power tools in damp or wet locations or expose them to rain Keep work area well lighted 5 KEEP CHILDREN AWAY AIl visitors should be kept safe distance from work area 6 MAKE WORKSHOP KID PROOF with padlocks master switches or by removing starter keys 7 DON T FORCE TOOL It will do the job better and safer at the performance level for which it was designed 8 WEAR PROPER APPAREL Do not wear loose clothing gloves neckties rings bracelets or other jewelry which may get caught in moving parts Non slip foot wear is recommended Wear protective hair covering if you have long hair 9 ALWAYS USE SAFETY GLASSES Also use face or dust mask for commercial cutting operations Everyday eyeglasses only have impact resistant lenses
28. he tool s plug Repair or replace damaged or worn cord immediately To avoid the possibility of the appliance plug or receptacle getting wet position tile saw to one side of a wall mounted receptacle to prevent water from dripping onto the receptacle or plug The user should arrange a drip loop in the cord connecting the saw to a receptacle The drip loop is that part of the cord below the level of the receptacle or the connector if an extension cord is used to prevent water from traveling along the cord and coming in contact with the receptacle If the plug or receptacle does get wet don t unplug the cord Disconnect the fuse or circuit breaker that supplies power to the tool Then unplug and examine for presence of water in the receptacle Only UL listed extension cords should be used with this product Improper use of extension cords may cause inefficient operation of your tool which can result in overheating Be sure your extension cord is rated to allow sufficient current flow to the motor For the proper gauge for your tool please see chart Do not let your fingers touch the terminals of plug when installing or removing the plug to or from the outlet If not properly grounded this power tool can incur the potential hazard of electrical shock particularly when used in damp locations or in proximity to plumbing If an electrical shock occurs there is the potential of a secondary hazard METAL SCREW A GROUNDING PIN
29. ien Ne jamais laisser la pompe fonctionner sec Elle est se refroidit automatiquement en pompant le liquide Un usage sec causera des dommages la pompe et peut endommager le moteur R gler le guide de refend en le positionnant au point d sir et serrer le verrou Bloquer fermement le guide de refend afin d viter tout mouvement Le guide de refend peut tre utilis pour les coupes droites 90 degr s de c t gauche comme de c te droite Noter des fentes droites et 45 degr s au bas du guide de refend Voir Illustration Une fois le guide est positionn pour la coupe d sir e placer le mat riel au ras contre le guide et la r gle gradu e Pour les coupes 45 degr s positionner le coin du mat riel couper dan la fente de la r gle gradu e c Tout est alors pr t pour la coupe Diagonale s12 PROC DURES D UTILISATION Ts ile 2 Avant toute mise en service il est n cessaire de lire ce manuel dans sa totalit na NOTER La scie comporte deux interrupteurs Les deux interrupteurs doivent tre la position d ON e Le premier interrupteur est sur le moteur Appuyez le la position de BAS et de VERROUILLER e Le deuxi me est situ sur le support du moteur et il est encastr L interrupteur a deux positions le I et le O Appuyer le I pour brancher l interrupteur Cet interrupteur est l interrupteur primaire pour le fonctionnement de votre scie Assurer qu il y a amplemen
30. l is intended for use on a circuit that has an outlet that looks like the one illustrated in Figure A The tool has a grounding plug that looks like the plug illustrated eR CONNECTING TOOL TO POWER SOURCE OUTLET This machine source must be grounded while in use to protect the operator form electrical shock In the event of a malfunction or breakdown grounding provides a path of least resistance for electrical current to reduce the risk of electrical shock This tool is equipped with an electric cord having equipment grounding conductor and a grounding plug The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances Do not modify the plug provided if it will not fit the outlet Have the proper outlet installed by a qualified electrician Improper connection of the equipment grounding conductor can result in a risk of electric shock The conductor with insulation that is green ont he outside with or without yellow stripes is the equipment grounding conductor If repair or replacement of the electric cord or plug is necessary do not connect the equipment grounding conductor to live terminal Check with a qualified electrician or service personnel if the grounding instructions are not completely understood or if in doubt as to whether the tool is properly grounded Use only 3 wire extension cords that have 3 prong grounding plugs and 3 pole receptacles that accept t
31. les poteaux verticaux A 2 Placer le support du moteur dans les poteaux verticaux et serrez les 2 vises avec ailes pour retenir le support du moteur fermement Voir Illustration 1 11 INSTALLATION DU DISQUE ET PROTECTION DE DISQUE 1 Enlever la protection de disque et la mettre de c t 2 Soulever la protection de disque la plus haute que possible et serrez les vises avec ailes Ensuite enlever I crou d arbre de disque et le flasque ext rieur 3 Placer le disque sur l arbre en le poussant contre le flasque int rieur V rifier que le disque soit install afin que la fl che directionnelle pointe vers le bas dans le sens de rotation F 4 Installer ensuite le flasque ext rieur l crou d arbre et serrez l crou Eviter de trop serrer 5 Descendre la protection de disque et serrez les vises avec ailes 6 Pour enlever le disque suivez les tapes l inverse Voir Illustration 2 F a ILLUSTRATION 2 CE Ca INSTALLATION DE LA POMPE A EAU 1 Enlever la pompe eau de son emballage et l examiner afin d assurer qu elle ne comporte ni fissures ni dommage Voir Illustration 3 gt 2 NOTER LES DIRECTIVES DE S CURIT ET L ENTRETIEN POUR LA Fixer les extr mit s du tuyau en plastique qui pendent de la protection de disque la t tine de la pompe eau Placer la pompe eau l arri re du bac eau sur son c t avec la t tine de la pompe eau aussi sur son c t Remplir le bac
32. longe de capacit insuffisante peut provoquer une surchauffe du moteur o m me br ler le moteur Nous recommandons la v rification de l alimentation d lectricit par un lectricien professionnel pour assurer la s curit de l op rateur Le plus petit le num ro de calibre le plus lourd le cordon lectrique ATTENTION POUR VITER D ENDOMMAGER LE MOTEUR N UTILISEZ QUE DES RALLONGES RECOMMAND ES NE JAMAIS UTILISER PLUS QU UNE RALLONGE LA FOIS CALIBRE MINIMUM POUR RALLONGE 18 AWG 16 AWG 16 AWG 14 AWG RALLONGE LONGUEUR IN PIEDS 25 50 100 150 CARACT RISTIQUES LECTRICIT SP CIFICATIONS DU MOTEUR e Moteur de 24CV 4000 TPM e Puissance en Chevaux 24CV rendement e Volts 115V e Interrupteur automatique pour prot ger le moteur de e Amp res 58 scie contre la surchauffe et la surtension lectrique e TPM 4 000 e Monture de disque con u pour faciliter le e Cycle 60 remplacement du disque e Phase 1 e Bac a eau en plastique impr gn de fibre de verre j ee ki scie 1 plus pr s possible CE la soues de Facile enlever et monter RALLONGES LECTRIQUES Assurer que la rallonge ne soit pas plus petite qu un calibre 12 et de 20 amp res minimums et quip e de trois broches Une rallonge de capacit insuffisante peut provoquer une perte de puissance et une surchauffe du moteur Nous recommandons la v rification de l alimentation lectrique par un lectricien professionnel afin d assurer la s curit
33. mbly e Fiberglass Impregnated Plastic Water Tray e 45 90 Rip Guide CUTTING HEAD ASSEMBLY INSTALLATION CAUTION FOLLOW ALL OF THE ASSEMBLY amp INSTALLATION INSTRUCTIONS COMPLETELY BEFORE CONNECTING THE SAW TO A POWER SOURCE OR TURNING THE MOTOR ON 1 Remove the motor mount block and motor from the packaging loosen the wing screws enough to permit the motor mount to fit on the frame upright post 2 Set the motor mount block on the frame upright post then tighten the 2 wing screws to hold the motor block securely in place Diagram 1 BLADE amp BLADE GUARD INSTALLATION 1 2 5 6 WATER PUMP INSTALLATION Ie Remove the blade guard and set it aside in the cutting head Raise the blade guard to the highest level and tighten the blade guard wing screw Then remove the blade shaft nut and outer flange Place the blade onto the shaft pushing it up against the inner flange Make sure the directional arrow is pointing in the direction of rotation Replace the outer flange and blade shaft nut With one hand hold the blade and tighten the blade shaft nut with your free hand Make certain the nut is firmly tightened with wrench provided DO NOT OVER TIGHTEN Lower the blade guard into position and tighten the wing screw To remove the blade reverse the installation steps See Diagram 2 Remove the water pump from its box and ensure that it is not cracked or damaged in any way See Diagram 3 Attach th
34. or material and upon returning the product to distributor dealer in its original packaging Q E P will repair and or replace it free of charge This warranty DOES NOT COVER normal wear nor any damage as a result of accidents misuse abuse or negligence Q E P s obligations under this warranty shall be limited to the repair and or replacement of the product Q E P shall not be liable for consequential damages This warranty is void if the product or any of its components are modified altered or in any way changed or if the product is used in a manner or with a blade that is not recommended by Q E P The water pump is excluded from this warranty and is subject to its manufacturer s warranty This warranty is in lieu of all other warranties expressed or implied IMPORTANT The warranty card must be filled out and received within 30 days of purchase to validate warranty GARANTIE LIMITEE Ce produit est couvert par une garantie de 30 jours a partir de la date d achat Si le produit est d fectueux dans sa fabrication ou ses mat riaux Q E P le r parera et ou le remplacera gratuitement si le produit est retourn dans son emballage d origine au distributeur repr sentant Cette garantie NE COUVRE PAS l usure normale ou tout dommage caus par des accidents un usage anormal abusif ou n gligent Les obligations de Q E P sous cette garantie seront limit es la r paration et ou au remplacement du produit Q E P ne sera pas responsable des dommages
35. outil est con u pour se brancher sur un circuit dot d une prise ressemblant celle repr sent e au dessin A Sa fiche avec terre ressemble aussi celle du dessin A Si aucune prise correctement reli e la terre n est A FICHE AVEC TERRE disponible vous pouvez utiliser temporairement un adapteur pour brancher la fiche dans une prise bipolaire comme illustr aus dessins B amp C Cet adapteur ne nu doit tre utilis qu en attendant l installation d une prise T correctement reli e la terre par un lectricien qualifi Les broches rigides de couleur verte qui d passe de l adapteur doivent tre connect es une prise de terre permanente comme celle d une prise murale avec terre Ta C ADAPTEUR AVEC TERRE VIS EN M TAL B PRISE MURALE AVEC TERRE Os MISE EN GARDE POUR VOTRE S CURIT LISEZ CE MANUEL D UTILISATION AVANT D UTILISER LA SCIE e Porter des lunettes de s curit e Utiliser votre protection anti claboussures en tout temps D brancher l outil avant de le nettoyer changer le disque ou de le r parer Remplacer les disques de d coupe diamant s endommag s Placer l outil sur une surface nivel e afin qu il fonctionne correctement Remplir la cuvette d eau jusqu au niveau indiqu UTILISER QUE DES RALLONGES LECTRIQUES DE CAPACIT RECOMMAND E et en bonne condition Assurer que les rallonges soient de calibre 18 minimum quip s avec 3 broches Une ral
36. que ae de 12 Flasque Ext rieure euleuse Disque Tube pour D bit d eau en forme de Y 16 1 Tube pour D bit d eau en forme de L 16 2 Couvercle pour Interrupteur Automatique Interrupteur l Epreuve de l Eau Cordon Electrique Cordon Electrique T te Fixe Interrupteur de Surchauffe Automatique Prise Simple Plaquette de Bas Pompe Eau Clef 25 14 PAUTAS DE SEGURIDAD PARA LA SIERRA LEA EL MANUAL DE OPERACION COMPLETAMENTE Y ASEGURESE QUE ENTIENDE TODAS LAS PAUTAS DE SEGURIDAD 1 KEEP GUARDS IN PLACH nd in working order 2 REMOVE ADJUSTING KEYS amp WRENCHES Form a habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on KEEP WORK AREA CLEAN Cluttered areas and benches invite accidents DON T USE IN A DANGEROUS ENVIRONMENT Don t use power tools in damp or wet locations or expose them to rain Keep work area well lighted KEEP CHILDREN AWAY AIl visitors should be kept safe distance from work area MAKE WORKSHOP KID PROOF with padlocks master switches or by removing starter keys DON T FORCE TOOL It will do the job better and safer at the performance level for which it was designed WEAR PROPER APPAREL Do not wear loose clothing gloves neckties rings bracelets or other jewelry which may get caught in moving parts Non slip foot wear is recommended Wear protective hair covering if you have long hair 9 ALWAYS USE SAFETY GLASSES Also use f
37. rbre ne soit pas abim avant d installer le disque Toujours utiliser les disques avec arbres compatibles et de m me dimension que la flasque Assurer que le disque soit install afin que la fl che directionnelle pointe vers le bas dans le sens de rotation et soit install de fa on solide et ferme Porter des protections de s curit Porter des lunettes protectrices et un masque en tout temps V rifier que le disque n aille pas de signes d endommagement ou des fissures Assurer un d bit d eau constant sur les deux c t s du disque avant de couper NE PAS FAIRE o VN Ne pas utiliser cette machine sans protection de disque Ne pas utiliser les disques plus grands ou plus petits que 7 pouces de diam tre Ne pas couper sec avec les disques con us pour les coupes l eau Ne pas exc der les TPMs recommand s par le fabricant du disque Ne pas forcer le mat riel couper Laisser le disque couper sa propre vitesse Ne pas couper autres mat riaux que ceux recommand s par le fabricant de disque 13 SCIE EAU DIAGRAMME DESCRIPTION no 60007 SCIE EAU Bac Eau mae LISTE DE PiECES Barre Guide Hable Ge Coupe oee DESCRIPTION No Guide deRetend 457790 5 Plaquette de Monture 10 Guide de Refend 45 90 Vises avec Ale 101 bouton d Austen Protection de Disque 11 ns Bouton d Ajustement pour aane TE ey Protection de Disque 11 1 Bus ing ar Metal Ecrou de Verrouillage de Dis
38. rrect arbor size on a compatible arbor shaft 5 Ensure the blade is mounted with the rotation arrow in the proper direction and is securely tightened with the wrench 6 Always wear the proper safety equipment at all times when operating the saw Wear goggles and dust mask at all times when operating saw 7 Periodically check the blade for cracks or bond fatigue 8 Always have a continuous flow of water on both sides of the blade before cutting any material DON Ts 1 Do not operate the saw without all safety guards in position 2 Do not operate the saw with blades larger or smaller than 7 3 Do not cut dry with blades marked Use Wet 4 Do not exceed maximum RPMs recommended by the blade manufacturer 5 Do not force the material into the blade Let the blade cut at its own speed 6 Do not cut material not recommended by the blade manufacturer PA 7 DIAGRAM OF WET SAW 24 181 P m 60007 7 WET SAW PARTS LIST 2 ay 12 F ia 14 15 DESCRIPTION Water Tray Assembly Frame Assembly Roller Guide Bar 45 90 Rip Guide 45 90 Rip Guide Adjustment Knob Angle Bar Rollers Set Metal Bushing Set of 12 Angle Grinder Wing Screw Blade Guard Blade Guard Adjustment Knob Blade Lock Nut Outer Flange Blade Inner Flange Water Flow L Cover for Automatic Overload Switch Electrical Cord Electrical Cord Fixed Head Automatic Overload Switch Single Socket Bottom
39. rvice the pump in any way Never let the pump operate dry It is self cooled by pumping liquid Dry use will cause pump damage and may cause the motor to fail Set the rip guide by positioning it on the desired dimension and tighten the threaded knob on the rip guide Make sure rip guide is firmly tightened to avoid slippage The rip guide can be used for 90 rip cuts and 45 rip cuts from both the left and right side Notice the straight and 45 angled slits on the bottom of the rip guide in the diagram After the rip guide is positioned for the desired cut place material flush against the rip guide and the measurement rail For 45 rip cuts place the corner of material in the open slot of the measurement rail Diagonal cut BGs SAW OPERATION Make sure you have read this manual completely before operating your saw NOTE The saw motor has two ON OFF switches Both switches must be ON for your saw to operate e One switch is located on the motor housing Push this switch to the DOWN and LOCKED position e The second switch is located on the motor mounting block enclosed in a protective housing This rocker switch has I and O markings Press the I to turn the switch ON This switch should be used as the primary ON OFF switch for saw operation Make sure that there is sufficient water in the water pan to cover the inlet on the water pump and that water is being supplied to the saw blade
40. t d eau dans le bac eau et v rifier que l entr e d eau soit submerg e Assurer que le mat riel couper soit positionn correctement sur la table de coupe avant de couper Pousser le mat riel lentement vers le disque Ne pas forcer le mat riel couper Toujours suivre les r gles de s curit Porter des lunettes protectrices un masque et des gants lorsque vous utilisez votre scie Ne jamais utiliser un disque endommag ENTRETIEN DE LA SCIE MISE EN GARDE AVANT D EFFECTUER L ENTRETIEN OU LE NETTOYAGE ARR TEZ LE MOTEUR ET D R Or ET ee INS oe Sn a BRANCHEZ LE CORDON ECTRIQUE DE LA PRISE DE COURANT D FAUT DE CE FAIRE POURRAIT SULTER AUX BL SSURES S RIEUSES L UTILISATEUR Pour la long vit et un meilleur rendement nettoyez la scie apr s chaque usage Essuyer toutes les surfaces ext rieures et gardez la table propre et libre de d chets Essuyer les deux barres guide et les rouleaux sur la table de coupe Les barres sont trait es sp cialement pour vous offrir de longue service Utiliser l huile l g re pour lubrifier les barres guides Toujours v rifier si le disque comporte ni fissures ni d t riorations FAIRE ET NE PAS FAIRE FAIRE V rifier le disque quotidiennement pour des fissures ou l usure anormale Jeter les disques tordus ou ceux qui a des tissures ou br chures Utiliser un disque appropri au type de travail accomplir V rifier que l a
41. ted plastic water tray withstands even the toughest punishment Easy to remove and install e Connect saw as close as possible to power source The adjustable rip guide allows both 90 and 45 cuts Rip cut up to 16 square tiles and diagonal cut up to 10 tiles Easily removable for cleaning and transportation Lightweight for easy setup and maintenance EXTENSION CORDS When using an extension cord ensure all cords are no smaller than 12 gauge rated at a 20 AMP minimum and equipped with 3 prong plugs Use of anything smaller may result in overheating or burn out of the motor It is recommended to have an electrician check the voltage at the saw motor to ensure proper voltage to run the saw efficiently and safely UNPACKING ASSEMBLY amp SETUP CAUTION FOLLOW ALL OF THE ASSEMBLY amp INSTALLATION INSTRUCTIONS COMPLETELY BEFORE CONNECTING THE SAW TO A POWER SOURCE OR TURNING THE MOTOR ON Carefully open the container and remove all saw components and packing materials Ensure that you have checked each item with the exploded view on Page before discarding the container or packing materials The contents of the container are as follows e Cutting Head Assembly e Close Wrench e 7 Saw Blade e Owner s Manual e Blade Guard Accessory The following pages illustrate step by step the installation of various components and operation of the saw Read instructions completely before operating this saw e Water Pump e Saw Frame Asse
42. y support the pump and piping to reduce the chance of pump failure or damage Never handle the pump by the cord with wet hands or when standing on a wet surface Do not use the pump to pump anything other than water or other compatible liquids Never use to pump gasoline kerosene or other combustible or corrosive liquids Should pump fail always disconnect from power source before handling pump or attempting to unclog or service the pump in any way Never let the pump operate dry It is self cooled by pumping liquid Dry use will cause pump damage and may cause the motor to fail Set the rip guide by positioning it on the desired dimension and tighten the threaded knob on the rip guide Make sure rip guide is firmly tightened to avoid slippage The rip guide can be used for 90 rip cuts and 45 rip cuts from both the left and right side Notice the straight and 45 angled slits on the bottom of the rip guide in the diagram After the rip guide is positioned for the desired cut place material flush against the rip guide and the measurement rail For 45 rip cuts place the corner of material in the Diagonal cut open slot of the measurement rail 18 OPERACION DE LA SIERRA Make sure you have read this manual completely before operating your saw NOTE The saw motor has two ON OFF switches Both switches must be ON for your saw to operate e One switch is located on the motor housing Push this switch to the DO
Download Pdf Manuals
Related Search