Digiplex APR3-ADM2 : User Guide
Contents
1. InTouch 7 If the Hang Up feature is not used A and if no action is performed after two minutes the APR3 ADM2 will hang up automatically SYSTEM CHECKLIST Telephone Number Output Activates Output follows J Output Timer O Manual Deactivation Output Timer Length O sec or LJ min Call hang up and then call back within sec of rings before the APR3 ADM2 answers Area Assignment 01020304 5U60U7U08 Your user access code must also have A access to the areas partitions to which the APR3 ADN2 is assigned 8 Digiplex EVO User Manual APR3 ADM2 EXAMPLE Example 1 Using the APR3 ADM2 Nelson has a security system with an APR3 ADM hooked up at home His security system has two areas Both areas are presently armed and the APR3 ADM2 s output which is hooked up to his garage door opener is deactivated Nelson is on his way home and wishes to disarm both areas and open his garage door Nelson performs the following Nelson first dials the telephone number of the line to which the APR3 ADM2 is connected prompt Nelson with the following Please enter your code Nelson enters his user access code rd C When the APR3 ADM2 picks up it will InTouch 9 C The APR3 ADM2 then prompts Nelson with the following Area 1 armed Area 2 armed Output is deactivated To modify enter area number Nelson presses the 1 key on his telephone2. to disarm Area 1 The APR3 ADM2 then prompts Nelson with the following Area 1 disarmed Area 2 armed Output is deactivated To modify enter area number Nelson presses the 2 key on his telephone to disarm Area 2 The APR3 ADM2 then prompts Nelson with the following Area 1 disarmed Area 2 disarmed Output is deactivated To modify enter Area number 10 Digiplex EVO User Manual Kp Nelson then presses the key and f then the 0 key on his telephone to activate the output connected to the garage door C The APR3 ADM2 then prompts Nelson with the following Output is activated InTouch 11
3. DIGIPLEX EVO Voice Assisted Arm Disarm Module User Manual P A RA D O X SECURITY SYSTEMS Printed in Canada 06 2007 paradox com APR3ADM2 EU02 TABLE OF CONTENTS INTRODUCTION 221 pri henna eor ce etx 00g 4 ACCESS CODES ici RN d 4 HOW DO SE ET eie re pe deese ce eus eu pe oven 4 THINGS Y oU SHOULD KNOW 5 When Accessing your APR3 ADM2 5 When Arming or Disarming 6 When Activating or Deactivating an Output 6 When Using your APR3 ADM2 cesses 7 TELEPHONE PUSH BUTTON FEATURES 7 Clear Activate Deactivate APR3 ADM2 Output 2 0 Hang Up V 8 erra rtr sr rtr kin SYSTEM CHECKLIST eese 8 APR3 ADM2 EXAMPLE een 9 COMPATIBILITY EVO48 EVO96 EVO192 DGP NE96 DGP 848 INTRODUCTION Congratulations for choosing the Paradox Voice Assisted Arm Disarm Module The APR3 ADM turns any touch tone telephone into a keypad With the APR3 ADM2 you can now arm or disarm your Digiplex EVO security system as well as activate or deactivate your APR3 ADM2 s output all from your telephone Using detailed voice prompts to guide your way the APR3 ADM is as simple as picking up your telephone ACCESS CODES The APR3 ADM2 uses your security system user access code to grant you access to your security system The user access code you would enter into your system keypad is the same user access cod
4. e you will use to enter on your telephone How Do I USE IT STEP 1 Pick up your telephone and dial your telephone number the telephone number of the line that your APR3 ADN2 is connected to 4 Digiplex EVO User Manual STEP 2 STEP 3 STEP 4 The APR3 ADWM2 asks you to enter your user access code Enter your user access code If your security system is programmed to accept variable code lengths you must press the 7 key after entering your access code Keys 1 to 8 on your telephone represent areas 1 to 8 just like your keypad To arm or disarm your security system press the desired area s number on your telephone This will toggle the area s arming state from armed to disarmed and vice versa Refer to Example 1 on page 9 To activate or deactivate the APR3 ADM s programmable outputs PGMs press the 4 key and then the 0 key Refer to Example 1 on page 9 THINGS YOU SHOULD KNOW When Accessing your APR3 ADM2 Toaccess a system that is connected to an answering machine or service call the InTouch 5 APR3 ADM2 hang up wait 10 seconds and then call the APR3 ADM2 again When Arming or Disarming You will only be able to arm or disarm areas that your user code has access to If you were to arm an area with an open zone you security system will Force Arm the area This will only happen with user access codes that have the Force Arm feature enabled When Activating or Deactivat
5. ing an Output Your APR3 ADM2 s output can be used to turn on lights open or close a garage door and much more Ask your installer about this useful feature If the APR3 ADM2 s output is not operational you will not be able to activate or deactivate the output Your installer can program the output to either deactivate manually or follow a timer If programmed to be deactivated manually the output will remain activated until you deactivate it If programmed to follow a timer the output will deactivate after the timer has elapsed 6 Digiplex EVO User Manual When Using your APR3 ADM2 n some cases your telephone s tone may not be powerful enough to interrupt the APR3 ADM2 s voice prompt If this is the case simply wait for the APR3 ADM 2 s voice prompt to finish before entering your action e f your security system and APR3 ADM2 share the same telephone number you may be interrupted at times when using your APR3 ADM2 TELEPHONE PUSH BUTTON FEATURES Clear If you have made an error press the key on your telephone to clear the error and then re enter the information Activate Deactivate APR3 ADM2 Output 2 0 To activate or deactivate the APR3 ADM2 s output press the key and then the 0 key from your telephone Hang Up 9 When you wish to hang up press the key and then the 9 key to immediately hang up The APR3 ADM2 will confirm the hang up with Good bye
Download Pdf Manuals
Related Search