Installation Beep & Park n°1
Contents
1. s and the template s centres are aligned Install the camera mounting on the windscreen gt Place the mounting on the smaller notch in the template s lower side gt Remove the template and ensure the camera mounting adheres to the windscreen properly smoothing the adhesive patch carefully Position the camera simply by screwing it onto the mounting Check that the camera module does not hinder the central rearview mirror s movement and does not obstruct the driver s line of sight e Disconnect the battery gt Switch off the engine first gt Wait for 2 minutes before you disconnect the battery to give the vehicle s computers sufficient time to power off completely e Connect the power cable RJ45 connector to the camera module Pass the module s power cable to the driver s side of the dashboard either hide the cable under the central rearview mirror gt or connect it unobtrusively to the rearview mirror s edge with the small self adhesive cable clips provided gt then feed the cable into the windscreen side pillar and the door pillar AN Take care not to obstruct any airbag e Connect the wiring cable s different wires gt White brown stripes brown to ACC gt White orange stripes orange to ground gt Blue to speed output gt Green to left turn indicator gt White blue stripes to right turn indicator gt White green stripes not used On certain vehicl2. What is it Camera module that supervises all 4 driving assistance functions e Lane departure alert e Keep in lane assistance e Video recording of a potential accident e Alert that vehicle in front has moved away How does it work e All four functions are housed in the camera module facing the road e The system starts automatically as soon as the vehicle starts and scans the road permanently e All of the guideo functions can be easily configured or switched off using the remote control 1 The Lane alert function uses an algorithm to detect when the vehicle crosses white road markings and immediately informs the driver with an audible alert or voice message A warning is given as soon as the vehicle crosses the line leaving the driver enough time to regain control of the vehicle 2 The Optilane function uses an algorithm to spot any vehicle drift in relation to the road markings and immediately informs the driver who can then correct the trajectory accordingly The driver is informed as soon as the vehicle drifts to the left or the right for more than 5 seconds The Lane Alert and Optilane functions are deactivated when the driver uses the indicators The system is compatible with white and yellow road markings 3 The Video box function films 20 second video sequences in the event of sudden acceleration or deceleration The system films the moments immediately before and after an impact The videos can then be t
3. a and function settings e No special tools required e Average estimated installation time 1 hour The following installation assistance is available e Detailed illustrated installation guide in this document e Technical support hotline A universal product e Can be installed in any type of passenger car 4WD vehicle or light van 12V e Compatible with other aftermarket products The most important element consists of sensing the vehicle s speed how simple this is depends on the vehicle concerned Vehicle s speed information cannot be sensed on certain models gt Very old vehicles over 15 years old with a mechanical cable driving the milometer no electrical soeed output Since the ABS function has been generally adopted speed information is now relayed electrically in all models Technical specifications Installation time 1 hour amp KOOO Tools required 1 Wire stripper pliers Kit components 2 Screwdriver set _ 1 Camera module 3 Insulating adhesive tape 2 Power cable 4 Wire cutting pliers 3 USB cable 5 Multimeter 4 Positioning template 6 Soldering iron 5 Cable ties 6 Cable clips 7 Remote control 8 CD ROM As the battery must be disconnected during installation some data may be lost radio station settings vehicle locking code etc 1 Preparing for installation e Before installing the system check that the vehicle is parked on level ground and the turn i
4. ant 2 Device and accessories 3 Product details 1 Before Installation 2 Important 3 Installation Guide 3 1 Before fixing Functions 3 2 Using Guiding Pad 1 Video Box 3 3 Positioning 2 Lane Alert 3 4 Fixing nnd BORN OE enn fms AMaNging Wires annn anaanno p oannaam 4 Optilane 3 6 Angle Adjustment 5 Driving Time Display 4 Checklist 6 Messages amp Display Remote Control Program Gui ie 1 Buttons A gt Power and default mode 1 Software Installation Appendix 3 Installation and 2 Driver Installation l vehicle type 3 Main software Features abea edie 4 Volume and sound settings 4 Icons i specifications S Video Box 5 How to download data 6 Lane Alert settings 6 Displaying image amp data 7 7 Function activation 8 Other guides Valeo Movie file creation and playback Recommandations in daily use A A A A Keep guideo dry when cleaning the vehicle interior Water can damage the electronic circuits and cause fire or electric shock Avoid contact with chemicals and detergents which can damage the surface of guideo and the internal circuits Guideo cannot function correctly with obstacles in its field of vision Make sure that the windshield glass in front of it is clean Similarly make sure that there are no objects near the device since their shadows may interfere with performance When not using the device avoid direct exposure to sunlight to avoid that the system g
5. es equipped with an onboard computer an error message may be generated when the system is connected to the turn indicators because the connection is interpreted as a defect In this case you must add an anti feedback diode to the connection so that the computer does not interpret it as a fault Reconnect the battery and switch on the engine again gt On multiplexed vehicles wait for 1 minute before switching on the engine to ensure that the vehicle s computers are reinitialised properly Check that the camera module switches on and off with the engine Check that the turn indicators are connected properly A left turn indicator and right turn indicator signal should be displayed on the camera s rear screen when the turn indicators are activated or when neither turn indicator is activated or when the left turn indicator is activated when the right turn indicator is activated Check that all of the remote control s functions work See the user manual on the CD ROM supplied Beep amp Watch j Vehicle speed On off l set up Left warning point Right warning point Lane alert on off Video Box sensitivity Video Box sensitivity EN ean eee E E Optilane on off See Default mode Decrease Lane alert sound CS Fm Image check y aa Vehicle type Installation guide Ca Select
6. ets hot Regular driving on uneven surfaces may shift the position of guideo and this may cause poor operation Please check from time to time that guideo is correctly positioned and angled After installation Troubleshooting No sound comes out of the device gt Check if the power cable is correctly connected If the power is not connected no display comes on gt Check if all the functions are disabled gt Check if the sound level is minimized If the sound level is low in noisy environment the sound may not be heard The Video Box is not saving video images gt The Video Box records video images only if an acceleration greater than 0 4g occurs in any direction Please make sure that the sensibility of impact for video recording is appropriate with the situation and adjust it with the remote control No warning occurs in case of lane departure gt The Lane Alert and Optilane feature start to operate after 2 seconds of watching road lines So after passing crossroads or no mark region the warning will come out after 2 seconds gt f you cross lines again while the warning message is still being given the second warning message is deleted gt f the road is narrow the warning sound comes later for the driver s convenience gt Check the correct angle set up Warning occurs without lane departure gt Check the setting of warning timing If set to earlier modes
7. ion of the vehicle type gt gt This button is used to set the vehicle type Make sure that it is set VU VV Y correctly a faulty setting can undermine the performance of guideo gt The vehicles are classified according to the height of the camera module and the vehicle width Installation height gt Passenger Car 110 cm 125 cm gt SUV1 125 cm 145 cm gt SUV2 145 cm 160 cm gt Bus about 170 cm gt Truck about 195 cm Press the vehicle button on the remote control until the proper vehicle type is selected Adjustment of the camera angle Pe The angle adjustment mode helps you install guideo in its exact position Press the Angle button on the remote control Loosen the screw and carefully adjust the camera by successive movements until the LED display shows 00 00 or close value screw back the camera module Press the Angle button again to exit the installation mode S lection of the language The L button is used to change between 3 languages including English The other 2 languages can be selected on a PC by the guideo manager program When pressed once the current language setting is announced English is selected When double pressed the next language is selected and announced accordingly After installation Guideo user manual gt See the user manual on the CD ROM supplied with the product Introduction Installation Guide 1 Import
8. ndicators and soeedometer work properly e Locate the vehicle s ACC and ground These are generally located at the fuse block e Locate the left and right turn indicator outputs These are generally located at the fuse block lighting control stalk or turn indicator tell tale e Also locate the vehicle s speed information gt either at its radio gt or at the speed output used by the GPS gt or at the ABS under the hood e Use the multimeter to check that It is indeed speed information Connect the multimeter s connection to the vehicle s ground and its connection to the located speed output gt Drive a short distance to check the information the reading should fluctuate between 0 and 12V On certain multiplexed vehicles the speed information is coded and cannot be used in unmodified form on the Peugeot 807 for example In this case you can connect an electronic decoder interface to the multiplexed cable in order to convert the electronic data into electrical speed information that the multimeter can recognise Position and stick the template provided under the central rearview mirror There are two possible configurations Windscreen mounted central rearview mirror position the template sliding the larger notch under the mirror mounting gt Ceiling mounted central rearview mirror position the template on the central line at the top of the windscreen checking that the windscreen
9. ransfered to a PC via a USB connection to be viewed or sent The Video box system can also be switched on manually by the driver at any time 4 The Beep amp watch function uses a change in images to identify movement in front of the vehicle and informs the driver when the car in front has moved off The system comes on after the x vehicle has been at a standstill for 3 seconds i Product contents Camera module e A single multi function camera e Visual and vocal alerts e LED screen integrated on the back of the module e Integrated loud speaker e Detachable camera for protection against theft e Works in poor light lt 1 lux Remote control Modular functions e Language selection e Selection of audible or voice message alert e Adjustable volume e Battery powered Guideo Manager software e CD Rom included for installation on PC e PC Windows 2000 XP Vista compatible Accessories e Guiding pad for immediate installation of the camera e Wiring cables e USB cable Fitting instructions CD Rom e User guide e Guideo Manager software e Language downloading software Easy to install Ready to use product for quick and easy installation All wiring cables and cable clips supplied e Easily positioned camera module thanks to the template supplied e Quick and easily fitted camera module thanks to the self adhesive patch e Remote control for controlling all camer
10. the driver may feel that the warning is too fast or occurs without a line being crossed gt n case of bad weather roads under construction or roads where lines have been erased guideo may not recognize the road lines appropriately Beep amp Watch system doesn t come on gt Check how the LED display is set LED display shows 00 00 gt This function is enabled when the vehicle is stopped Make sure the vehicle is completely stopped After installation Troubleshooting continued Optilane Guide doesn t come on gt Check how the LED display is set LED display shows 00 00 gt f either line is not present or both lines are very dim this feature doesn t operate appropriately The device sometimes gets hot gt In hot summer or under direct sun light the device may get hot as a result of external heat gt The internal electronic circuit and speaker may generate some heat without a breakdown Warnings occurs while lane departure and turning signal activated gt Check the correct connection of the turning signal See 3 5 section Valeo may not be held responsible for the incorrect installation or misuse of the products
Download Pdf Manuals
Related Search