Instructions for use
Contents
1. NJUJS W US5 UN Cl PROBLEMS Basic problem solving with a CD player is similar to troubleshooting other electrical or electronic equipment Always check the most obvious possible causes first such as the following examples No power display Power plug is not inserted into socket correctly Plug in securely into unit s IEC socket No playback when disc is loaded NO DISC displayed Disc is loaded with label side down Incorrect disc type Dirty disc Moisture humidity or cold affecting laser lens Re load with label side up Please load a standard audio CD Clean disk and try again Leave unit on for an hour to allow moisture to evaporate No audio output or output too Incorrect or missing connections Check connections are secure low No Display Mistracking sound jumping Dropouts in sound Digital input not working Remote control range has reduced Power not on connected Display set to off Audio connector plug not fully pushed in Cable Fault Unsuitable Cable e g cable grounds not connected Player is receiving vibration or shock Disc is dirty Moisture humidity or cold affecting laser lens Digital input lead not properly connected Faulty digital input lead Faulty optical lead No connection to that input Incorrect input selected Wrong data type sent to DAC Batteries are flat Control is not pointed directly towards the front panel of the player Batteries are runni2. XLR Balanced output wiring CAUTION ot ve geess BS rot d MOUNT UNIT ON SOLID SURFACE DO NOT REMOVE SCREWS OR COVERS UNDER ANY CIRCUMSTANCES NO USER SERVICEABLE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED ENGINEER SEE OWNERS MANUAL FOR FURTHER INFORMATION THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1 SUBCHAPTER J PART 1040 AT DATE OF MANUFACTURE THIS PRODUCT COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION ASS 1 LASER PRODU RIGHT LEFT RIGHT LEFT OPTICAL COAXIAL OPTICAL OPTICAL COAXIAL COAXIAL 1 2 1 2 DIGITAL INPUTS XLR BAL OUTPUTS NU VISTA CD 192KHz UPSAMPLING RECLOCKING 32 BIT DAC CD PLAYER Ze MUSICAL FIDELITY DESIGNED IN ENGLAND DATE OF MANUFACTURE SERIAL NUMBER MAXIMUM POWER CONSUMPTION 30W ce A 50 60H2 THIS APPLIANCE MUST BE EARTHED IMPORTANT CAUTIO we ter eet NTEGRAT NU VISTA 800 D AMPLIFIER ann Kran NAL POLU Y u sur
3. appliance are coloured in accordance with the following code WARNING This appliance MUST be earthed As the colours of the wires of the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in the plug proceed as follows he wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or coloured green or green and yellow or by the earth symbol The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black e f connecting to a BS1363 plug a 13 amp fuse must be used WARNING ANY MODIFICATIONS TO THIS PRODUCT NOT EXPRESSLY APPROVED BY MUSICAL FIDELITY WHO IS THE PARTY RESPONSIBLE FOR STANDARDS COMPLIANCE COULD VOID THE USER S AUTHORITY TO OPERATE THIS EQUIPMENT Page 5 GENERAL ADVICE Installation Precautions amp User Information This new Nu Vista CD is designed and built to provide trouble free performance but as with all electronic devices it is necessary to observe a few precautions Heed all warnings shown on the back of the product Only connect the Nu Vista CD to a mains outlet having the same voltage as marked at the back of the unit Always ensure that when disconnecting and reconnecting your audio equipment the mains
4. supply is switched off Position the mains lead and signal interconnects where they are not likely to be walked on or trapped by items placed on them Do not use near water or place water filled containers on the Nu Vista CD for example a flower vase or potted plants If water does spill inside immediately pull out the mains plug from the wall socket and inform your dealer who should then check the unit before further use Entry of liquid into the Nu Vista CD is dangerous and may cause electric shock or fire hazard Do not place the unit near direct heat sources such as radiators direct sunlight or other equipment Do not remove any covers or try to gain access to the inside There are no internal adjustments or fuses you can replace yourself Refer all service work to an authorised Musical Fidelity agent Note Unauthorised opening of the equipment will invalidate any warranty claim Dust regularly with a soft cloth or soft brush but be careful when using cleaning or polishing agents they may harm the surface finish The electronics in modern hi fi equipment are complex and may therefore be adversely affected or damaged by lightning For protection of the audio system during electrical storms remove the mains plugs If after sales service is required to help the dealer identify the Nu Vista CD please quote the serial number located on the rear panel of the unit Page 6 NILIeEVISLA CO INSTALLATION Introduction Co
5. to XLR balanced inputs on amplifier e g Nu Vista 800 For the 3 pin XLR socket wiring used in our products please see diagram bottom of page 9 Note XLR socket hot and cold pins BOTH carry signal on this product and therefore must not be grounded at the amplifier end Musical Fidelity amplifiers accept and use both signals for maximum balanced benefit If using another manufacturer s amplifier please consult their manual support for further information ILLUMINATIONS When used in darker environments for example listening or home theatre rooms It is possible to switch off selected features to minimise distraction The illumination features excluding the power standby LEDs can be switched on or off by pressing the DISPLAY button on the front panel There is also a corresponding button on the remote control To cover all options all 8 permutations are available for use tabulated below DISPLAY BASE ILLUMINATION VALVE ILLUMINATION To select the desired step simply press the DISPLAY button on the front panel or remote until the required step is reached After step 8 the unit reverts back to step 1 Please note switching off the unit will store the current step When next switched on the remembered setting will be overridden temporarily until after the initial 12 second mute delay Once the delay is up the unit will revert to normal operation but with the display LED settings as previously stored Page 13 Page 14
6. CFR chapter 1 sub chapter J based on the Radiation Control for Health and Safety Act of 1968 and is classified as a Class 1 laser product There is no hazardous radiation during normal use because invisible radiation emitted inside this product is completely confined within the protective housing However you must observe the following important warnings CAUTION THIS CD PLAYER USES INVISIBLE LASER LIGHT WHEN THE PLAYER OPERATES LASER LIGHT IS RADIATED INTERNALLY DO NOT REMOVE THE PROTECTIVE HOUSINGS USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE CAUSING EYE INJURY IF THIS PRODUCT DEVELOPS A FAULT PLEASE CONTACT YOUR AUTHORISED MUSICAL FIDELITY SERVICE AGENT DO NOT ATTEMPT TO SERVICE IT YOUR SELF AND DO NOT CONTINUE TO USE THIS PRODUCT IN A FAULTY STATE INTERNAL LASER WARNING LABELS bebe MOUNT UNIT ON SOLID SURFACE DO NOT REMOVE SCREWS OR COVERS UNDER ANY CIRCUMSTANCES THIS PRODUCT COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS NO USER SERVICEABLE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED ENGINEER SUBJECT TO TWO CONDITIONS CLASS 1 SEE OWNERS MANUAL FOR FURTHER INFORMATION B 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND LASER PRODUCT ul O THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1 SUBCHAPTER J PA
7. Het label op de achterzijde van dit apparaat een afvalbak op wielen met een kruis doorgehaald geeft aan dat dit apparaat niet samen met gewoon huishoudafval mag worden weggegooid Om mogelijke schade aan onze leefomgeving te voorkomen dient dit apparaat gescheiden van gewoon huishoudelijk afval te worden afgevoerd zodat het op een milieuvriendelijke manier kan worden gerecycled Neem voor beschikbare inzamelplaatsen contact op met uw gemeentelijke reinigingsdienst of met uw elektronica leverancier HAVITTAMINEN Yliruksattua jateastiaa kuvaava tarra tuotteen takalevyssa kertoo etta tuotetta ei saa kasitella normaalina talousjatteena Ymp rist n suojelemiseksi on tuote pidett v erill n muusta j tteest ja se on kierratettava ekologisesti kest v ll tavalla Ota yhteytt laitteen myyj n tai Pirkanmaan Ymparistokeskukseen l himm n kierratyskeskuksen l yt miseksi MMM AFSKAFNING BBSS Logoet med en skraldespand med kryds over p bagsiden af apparatet indikerer at dette produkt ikke m kasseres som normal husholdningsaffald For at forebygge mulig skade p milj et bedes De separere dette produkt fra andet affald og sikre at det bliver genbrugt p en milj rigtig m de Kontakt venligst de lokale myndigheder eller din forhandler for oplysning om n rmeste tilg ngelige opsamlingssted for elektronikaffald j AIAAIKAZIA ANOPPIVH2 TO 2HMA ME TON AIATEFPAMMENO TPOXHAATO KAAO AMOPPIMATON ZTHN NIZO OWH TOY MHXANHMATO2 AHA
8. NCE THAT MAY CAUSE UNDESIRED OPERATION O CLASS 1 LASER PRODUCT T AUDI OUTPUT RIGHT LEFT OPTICAL COAXIAL OPTICAL OPTICAL COAXIAL COAXIAL 1 2 1 2 Dx NU VISTA CD Ce 192KHz UPSAMPLING RECLOCKING Li 32 BIT DAC CD PLAYER Ge MUSICAL FIDELITY Les j9 Qli amp l amp XLR BALANCED OUTPUTS DIGITAL OUTPUTS DIGITAL INPUTS Se THIS APPLIANCE MUST BE Li DATE OF MANUFACTURE SERIAL NUMBER EARTHED IMPORTANT CONSUMPTION 30W 10 11 9 TUBE BUFFER line output RCA sockets 10 XLR BALANCED left and right outputs 11 S PDIF DIGITAL optical Toslink and coaxial RCA outputs XLR Balanced input and output lead plug connections Male Female EIA Standard RS 297 A Page 8 12 13 12 S PDIF DIGITAL optical Toslink and coaxial RCA inputs 1 and 2 13 IEC MAINS INPUT Pin functions 1 Ground cable shield 2 Normal polarity hot or 3 Inverted polarity cold or IN ILIA IST Aa C REMOTE CONTROL The remote control allows operation of the CD player at a distance Equivalent buttons on the remote control have the same functions as those on the front panel of the unit Other functions are only available by remote control As the handset uses an invisible infra red light bea
9. ONEI OTI TO TIPOION AYTO AEN l IPETIEI NA AIAXEIPIZOEI AN ZYNHOIZMENO OIKIAKO ATIOBAHTO MPO ANO YTH ENAEXOMENH ENIBAPYN2H2 TOY lIEPIBAAAONTO EXOPIZTE TO MPOION AMO TA AAAA ATIOPPIMATA O2TE NA EZAZOAAI2ZOEI H ANAKYKAQZH TOY ME TON l IPETIONTA TPOTIO NAPAKAAOYME NA ETIIKOINONHZETE ME THN TOTTIKH YTIHPEZIA ANAKYKAQZH2 H ME TO KATAZTHMA AT OPA lA TIEPIZZOTEPE2 AEMTOMEPEIE2 Page 17
10. PDIF output Connect RCA digital receiver to RCA digital outputs Use good quality fully connected signal and ground coaxial digital cables for optimum RCA digital signal transfer Optical S PDIF output Connect optical digital receiver to optical output Use good quality optical cables for optimum signal transfer Page FACILITIES amp CONNECTIONS COAXIA OPTICAL CD 1 1 2 Ga SZ C N N OO 00000 0 D Sle PAUBE EJECT STOP PLAY PREV NEXT LI oo 5 gt J J KR O N gt 5 SOURCE selector buttons DISPLAY CD control buttons IR RECEIVER window 1 9 6 T 8 ON STANDBY Button CD DRAWER IR RECEIVER window 2 DISPLAY button CO N O A CAUTION MOUNT UNIT ON SOLID SURFACE DO NOT REMOVE SCREWS OR COVERS UNDER ANY CIRCUMSTANCES NO USER SERVICEABLE COMRONENTS INSIDE REFER SERVICING TO QUALIFIED ENGINEER SEE OWNERS MANUAL FOR FURTHER INFORMATION THIS PRODUCT COMPLIES WI DHHS RULES 21 CFR CHAPTER 1 SUBCHAPTER J PART 1040 AT DATE OF MANUFACTURE eee THIS PRODUCT COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERE
11. RCA Nu Vista buffer output wiring WIRING EXAMPLES CAUTION MOUNT UNIT ON SOLID SURFACE DO NOT REMOVE SCREWS OR COVERS UNDER ANY CIRCUMSTANCES NO USER SERVICFABLE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED ENGINEER SEE OWNERS MANUAL FOR FURTHER INFORMATION THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1 SUBCHAPTER J PART 1040 AT DATE OF MANUFACTURE THIS PRODUCT COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO TWO CONDITIONS CLASS 1 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION LASER PRO RIGHT LEFT o DIGITAL OUTPU OPTICAL COAXIAL OPTICAL OPTICAL COAXIAL COAXIAL 1 2 XLR BALANCED OUTPUTS DIGITAL INPUTS NU VISTA CD 192KHz UPSAMPLING RECLOCKING 32 BIT DAC CD PLAYER amp MUSICAL FIDELITY DESIGNED IN ENGLAND DATE OF MANUFACTURE SERIAL NUMBER MAXIMUM POWER CONSUMPTION 30W ce V 50 60H2 THIS APPLIANCE MUST BE EARTHED IMPORTANT rc Ae CAUTION NU VI Cw INTR INTEGRATE gp ws STA 800 D AMPLIFIER
12. RT 1040 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED O B AT DATE OF MANUFACTURE INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION a AUDIO OUTPUT LN C RIGHT LEFT Ed A NU VISTA CD 9 Le B O 192KHz UPSAMPLING RECLOCKING a 32 BIT DAC CD PLAYER B LEFT OPTI AL COAXIAL OPTICAL OPTICAL COAXIAL COAXIAL by s 1 2 1 2 MUSICAL FIDELITY B DESIGNED IN ENGLAND A 50 60Hz OH B 1HIS APPLIANCE E l MUST BE S DATE OF MANUFACTURE SERIAL NUMBER EARTHED ee Een C XLR BALANCED OUTPUTS DIGITAL OUTPUTS DIGITAL INPUTS HO NL X AA CONSUMPTION 30 w THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1 SUBCHAPTER J PART 1040 AT DATE OF MANUFACTURE THIS PRODUCT COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO TWO CONDITIONS CLASS 1 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND LASER PRODUCT 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION Page 4 NW VISTA CEO SAFETY INFORMATION IMPORTANT U K only This unit is supplied in the U K with mains lead fitted with a moulded 13 amp plug If for any reason it is necessary to remove the plug please remove the fuse holder and dispose of the plug safely out of reach of children It must not be plugged into a mains outlet The wires in the mains lead supplied with this
13. TAWAY VIEWS Showing Cylindrical Electrodes and Tripod Like Supports CATHODE HEATER PLATE GRID METAL SHELL CERAMIC BASE WAFER INDEXING LUGS Typical Single Ended Nuvistor Triode UK English valve mentioned hereafter refers to the electron valve kind also known as electron tube in other parts of the world Page 2 CONTENTS NJUJS W US5 UN Cl Section Page Safety Information General advice Installation Facilities and connections Remote control handset Operation Digital Inputs Outputs and Illumination Wiring Examples Problems Specifications Manual history Item disposal information L aser information Mains plug UK only modification warning Installation precautions Introduction cleaning installation power connections audio connections Illustrations main unit front amp rear panels Operation and illustration Starting CD Eject Loading CD Pause Play CD Text Next Prev ious Stop Use as a DAC Coaxial 1 Input Coaxial 2 Input Optical 1 Input Optical 2 Input Notes Nuvista Buffer outputs Balanced outputs Illumination options RCA Nuvista buffer outputs XLR balanced outputs Basic fault finding Product specifications 10 11 12 13 14 15 16 17 Page 3 SAFETY INFORMATION CLASS I LASER PRODUCT The Nu Vista CD is a CD player which has been designed and manufactured according to FDA regulations title 21
14. WW S W USS U Z Instructions for use Thank you for purchasing the Musical Fidelity Nu Vista CD player The Nu Vista CD player uses our tried and tested ultra low distortion upsampling Digital to Analogue Converter circuitry which has impressively flat response and virtually immeasurable noise and distortion To further enhance functionality the DAC can be used with the inbuilt CD player or with external digital sources such as TV sound set top boxes and similar The Nu Vista CD features a valve buffer output circuit similar to that used in our original Nu Vista products It has since been refined to fulfil our latest practices and expectations This completes the CD player giving a perfect sound from a great looking full size unit The Nu Vista CD will aesthetically match with present and future Nu Vista series products Such a combination will yield one of the best high fidelity systems available at any price Used properly and carefully it should give many years of outstanding musical reproduction Dust regularly with a soft duster or soft brush but be careful when using cleaning or polishing agents they may harm the surface finish If there are any questions about the audio system please consult the dealer who is there to help and advise CU
15. ancels playback and stops disk Current track remains displayed and its time and name if CD TEXT is present on disc Pressing STOP again at this point resets the unit to initial state where disk information is displayed and the track is reset back to 1 for playback from beginning of disc Pressing the corresponding button on the remote handset has the same effect see page 9 Page 11 DIGITAL INPUTS Use as DAC To take advantage of our high quality digital to analogue conversion techniques this unit has been designed to enhance listening experience from other S PDIF digital audio sources such as TV or TV receiver boxes digital tuners media servers or any other device with S PDIF digital audio output Separately selectable inputs are available which allow up to two coaxial and two optical digital sources to be used Simply connect desired digital equipment to the inputs on this unit using suitable cable Any input can be used for most devices however bearing in mind the limits of the optical receivers it may be suggested that the OPTICAL inputs are used for lower bitrates such as tuner or TV stereo audio and the COAX inputs are reserved for higher bitrate units greater than 96 kHz if used COAXIAL 1 input To use the COAXIAL input 1 press the COAXIAL 1 button on the front panel Alternatively use the COAXIAL 1 button on the remote control The display will flash no lock in absence of digital input signal If a signal is presen
16. ers For the first 15 mins or so the Nu Vista valves are still warming up and the valve illumination will be yellow in colour After approx 20 mins the valves will have reached full thermal equilibrium and are at their optimal performance which is indicated by the illumination turning green CD To use CD press the CD button on the front panel Pressing the corresponding button on the remote handset has the same effect see page 9 EJECT The Eject button on the front panel controls loading tray to allow disc to be placed in unit Press Eject to open tray Pressing the corresponding button on the remote handset has the same effect see page 9 The eject button will work at any time regardless of current operation or input selection Loading CD Place chosen compact disc on tray label side up From this point two options are available Press Play Unit will close drawer and start playing disc from beginning of track 1 straight away Press Eject or gently push drawer Unit will close drawer read CD and wait for further instructions PAUSE PLAY Used to play currently displayed track from STOP Pressing once starts payback Pressing again will pause playback indefinitely until it is pressed again It is possible to select different tracks when PAUSEd see below Pressing play when on any external digital input reverts the unit to CD mode and plays displayed track Pressing the corresponding button on the re
17. his will invalidate the guarantee Page 15 Output Output impedance Output digital OdB level DAC DAC circuit Total correlated jitter Linearity Frequency response Channel separation Signal to noise ratio Total harmonic distortion Connections Line level outputs Digital outputs Digital inputs Power requirement Mains voltages Power Consumption Weight Unit only unboxed in shipping carton Maximum Dimensions Wide Height on standard flat feet on pointed feet Deep front to back including terminals Standard accessories IEC type mains lead Remote control Batteries Felt pads Spike Foot Spike Foot Cups Remote Feet Musical Fidelity reserves the right to make improvements which may result in specification or feature changes without notice E amp OE Page 16 SPECIFICATIONS 50 ohms balanced or single ended XLR output 4 4V R M S balanced nominal RCA output 2 2V R M S single ended nominal balanced and single ended outputs 32 bit Delta Sigma bit stream dual differential 8x over sampling lt 135 picoseconds peak to peak 0 1dB down to 96dB 10Hz to 20 kHz 0 2dB max gt 105dB 20 Hz to 20 kHz gt 117dB a wtd 0 00396 10Hz to 20 kHz 1 pair line level RCA connectors left and right outputs 1 pair line level XLR connectors left and right outputs 1 RCA coaxial S PDIF up to 24 bit 192 kHz 1 optical S PDIF up to 24 bit 96 kHz 2 RCA coaxial S PDIF up to 24 bit 192 kHz 2 op
18. m the front edge must be pointed directly towards the receiver window at the front of the player without visual obstruction between them If the range of the remote control greatly decreases replace the batteries with new ones Do not mix old and new batteries two are required size AAA LRO3 or SUM 4 Please dispose of used batteries in accordance with local regulations MUSICAL FIDELITY NU VISTA CD PAUSE PLAY Pause playback of track PAUSE PLAY NEXT Next track also fast forward through track PREV Previous track also beginning of track and rewind through track STOP Stops playback CD selects CD player function COAXIAL 1 COAXIAL1 selects COAXIAL 1 input 9 COAXIAL 2 COAXIAL 2 selects COAXIAL 2 input C OPTICAL OPTICAL 1 selects OPTICAL 1 input OPTICAL 2 OPTICAL 2 selects OPTICAL 2 input DISPLAY DISPLAY dims or switches off display C and other illumination effects Page 9 OPERATION Starting Once all connections are made switch on the unit using the POWER button on the front of the unit The display will light up and base LEDs under front panel and valve LEDs will show RED This means the outputs are muted and will remain in this state for about 12 seconds so no sound will be heard from the unit Once the delay is up the base LEDs go green indicating unit is ready for use and any source material selected and playing will be heard through the speak
19. mote handset has the same effect see page 9 CD TEXT This unit recognises CD text where present on the CD Album names and song titles where available are displayed in the lower portion of the screen Some discs do not contain this feature so no information will appear when using such discs Page 10 NU VISTA CD OPERATION NEXT Next button behaves in various ways From STOP to step track forward through the CD one track per press to select desired track Once the unit is on the last track further presses will have no effect on selected track number During PLAY back press once to skip to next track Hold down to fast forward through currently playing track Press PAUSE PLAY to cancel the fast forward and resume playing function Pressing the corresponding button on the remote handset has the same effect see page 9 PREV ious PREV button behaves in various ways From STOP single press es to step track backward through the CD one track per press to select desired track Once unit is back at track one further presses have no effect on selected track number During PLAY back press once to return to beginning of current track Further presses will go back by complete tracks Hold down to fast rewind through currently playing track Press PAUSE PLAY to cancel the rewind and resume playing function Pressing the corresponding button on the remote handset has the same effect see page 9 STOP C
20. ng out Check mains lead is connected and blue LED is lit by pushing PWR STBY button Press DISPLAY button to reactivate display Insert plug securely Check cable is connected at both ends N B some esoteric cables have internal wiring intentionally disconnected modified For best results on all inputs analogue AND digital please use good quality screened coax signal and screen directly connected both ends Move player away from loudspeakers etc Clean disc surface Leave unit on for an hour to allow moisture to evaporate Check input lead is fully secured Change lead Please use a good quality straight through signal and ground phono to phono lead Optical lead breakage This can occur if the optical lead is bent into a radius too small Avoid tight corners in routing optical leads Check connection and cable Select correct input Check source digital output is set for 16 bit stereo PCM or similar This particularly applies to some TVs most DVD players and other home theatre type devices that may give a MULTICHANNEL digital output Refer to the source equipment manual for further information Change batteries for a new set Ensure there is no obstruction between the remote control and player front Change batteries for a new set If none of these actions affect a cure please contact the dealer or an authorised Musical Fidelity service agent Remember never open the case of the Nu Vista CD as t
21. ngratulations on the purchase of the new Nu Vista CD player Great attention has been paid to internal layout isolating each circuit section to prevent possible interaction The unit features a finely tuned and tweaked Nu Vista valve buffer for smooth sound coupled with low noise and virtually no distortion This unit will give top quality performance when used as Atop quality CD player delivering the best performance possible from CD Atop quality DAC digital to analogue converter for other sources with digital outputs such as DAB radio Media player TV etc delivering the best audio performance using these sources The resultant performance achieved by this unit is among the best in the world It has excellent signal to noise ratio low distortion wide bandwidth and dynamic range with extraordinary resolution and fine detail Cleaning Before cleaning the unit switch off power at the mains switch and remove the mains plug from the wall socket Clean the cabinet and remote control unit using a moist cloth Using solvents white spirit or thinners is not advised as they could damage the surface finish Installation Position the Nu Vista CD on a stable horizontal surface where there is no risk of it being Knocked or subjected to vibration such as from loudspeakers Important note During normal operation the unit dissipates an appreciable quantity of power at all times and it is important that it is well ventilated The
22. o CD Lock indication Some devices may halt disable their digital output signal when nothing is playing This may result in NO LOCK being displayed even with proper connection present This is a quite normal response Playing something on the source device should bring up the Locked indicator and playback should resume normally This behaviour is dependent on implementation of external devices and therefore beyond our control Multichannel TVs DVD Blu ray players and related set top boxes sometimes output digital multichannel audio information Such information is not recognised by this unit To ensure correct operation of this unit check that the digital outputs on such equipment is set to give PCM 44 1 kHz 16 bit stereo or similar Consult equipment manufacturer s instructions support for further information on how to do this PCM is the standard which the unit supports Other sample rate stereo PCM equipment is supported too with 88 2 96 176 4 and 192 kHz sample rates on its COAX and up to 96 kHz on its optical inputs all inputs up to and including 24 bits Page 12 IN LU aA SYA C OUTPUTS AND ILLUMINATION Nu Vista Buffer outputs To use the Nu Vista buffer outputs simply connect RCA leads to AUDIO OUTPUT RCA sockets Connect other ends of RCA leads to RCA line inputs on amplifier BALANCED outputs To use the BALANCED outputs simply connect balanced XLR leads to XLR sockets Connect other ends of balanced leads
23. ques quip s de composants lectroniques rum DISPOSAL La etiqueta cruzada hacia fuera del compartimiento que aparece envel panel trasero del producto indica que el producto no se debe reciclarse como basura normal de la casa Para prevenir danos posible al ambiente separe por favor el producto de otra basura para asegurarse de que puede ser reciclada de una manera ambientalmente segura Entre en contacto por favor a su oficina gubernamental local o a su minorista paradas instalaciones disponibles de la colecci n RIFIUTI E E L etichetta del cassonetto barrato riportato sul retro dell apparecchio indica che il prodotto non deve essere smaltito tramite la procedura normale di smaltimento dei rifiuti domestici Per evitare eventuali danni all ambiente separare questo prodotto da altri rifiuti domestici in modo che possa venire riciclato in base alle procedure di rispetto ambientale Per maggiori dettagli sulle aree di raccolta disponibili contattate l ufficioxgovenativo locale od il rivenditore del prodotto FACHGERECHTE ENTSORGUNG Das auf der Ger ter ckseite angebrachte Label deutet daraufhin dass das Produkt nicht mit konventionellem Hauskehricht entsorgt werden darf Um Sch den und Verschmutzungen an Umwelt und Mensch zu vermeiden muss das Produkt fachgerecht entsorgt und von anderem Abfall getrennt werden Wenden Sie sich bei Fragen hierzu an Ihren Fachh ndler oder an eine ffentliche Informationsstelle DER AFVAL EN
24. t the display will show a steady locked message Pressing the corresponding button on the remote handset has the same effect see page 9 COAXIAL 2 input To use the COAXIAL input 2 press the COAXIAL 2 button on the front panel Alternatively use the COAXIAL 2 button on the remote control The display will flash no lock in absence of digital input signal If a signal is present the display will show a steady locked message Pressing the corresponding button on the remote handset has the same effect see page 9 OPTICAL 1 input To use the OPTICAL input 1 press the OPTICAL 1 button on the front panel Alternatively use the OPTICAL 1 button on the remote control The display will flash no lock in absence of digital input signal If a signal is present the display will show a steady locked message Pressing the corresponding button on the remote handset has the same effect see page 9 OPTICAL 2 input To use the OPTICAL input 2 press the OPTICAL 2 button on the front panel Alternatively use the OPTICAL 2 button on the remote control The display will flash no lock in absence of digital input signal If a signal is present the display will show a steady locked message Pressing the corresponding button on the remote handset has the same effect see page 9 Notes Pressing play while on any digital input will automatically switch back to internal CD player Eject can be operated without switching back t
25. tical S PDIF up to 24 bit 96 kHz 90 250VAC 50 60Hz universal 20 Watts maximum blue PWR LED lit Less than 0 5W in standby orange STBY LED lit 18 62 kg 41 Ibs 26 12 kg 57 Ibs 483 mm 190 mm 212 mm 395 mm 19 74 84 1594 Pan d n E AN 10 Amp type Nu Vista Integrated remote LRO3 or AAA manganese alkaline type 2 off 4 off 4 off 4 off 4 off NILIeEVISLA CO MANUAL HISTORY DISPOSAL INFORMATION RELEASE DATE CHANGES Nu Vista CD 6 July 2015 Issue 1 mR DISPOSAL Kal The crossed out wheeled bin label that appears on the back panel of the product indicates that the product must not be disposed of as normal household waste To prevent possible harm to the environment please separate the product from other waste to ensure that it can be recycled in an environmentally safe manner Please contact local government office or retailer for available collection facilities i d DISPOSITION La poubelle sur roulettes barr es X qui apparait en logo sur le panneau arri re du produit indique que celui ci ne doit pas tre trait comme un d chet domestique commun Afin de prot ger l environnement ce produit lectronique devra tre g r s par ment et donc recycl selon les nouvelles normes Europ ennes Rohs concernant les d chets d appareils lectroniques Pri re de contacter les services concern s gouvernementaux ou votre point de vente pour l limination et l enl vement de d chets lectroni
26. top and bottom are perforated to allow the smooth flow of heat through the unit However the unit must not be enclosed in a cabinet or placed where the ventilation holes are impeded as this could result in excessive heat build up The Nu Vista CD must be protected from humidity if the unit is moved from a cold place to a warm room leave the unit for an hour or so to allow sufficient time for the moisture to evaporate Power Connections The Nu Vista CD is supplied with a standard IEC mains cable which plugs into the IEC socket at the back of the unit See page 8 When plugged in and mains supply is present the orange STBY LED will light Audio Connections XLR audio outputs Use good quality XLR balanced audio cables fully connected signals and ground for optimum signal transfer This gives the best performance from the CD player when used in conjunction with an amplifier with fully balanced input such as the Musical Fidelity Nu Vista 800 Integrated RCA Nu Vista buffer outputs Use good quality RCA phono audio cables fully connected signal and ground for optimum signal transfer Digital Connections RCA S PDIF inputs Connect RCA digital sources to RCA digital inputs Use good quality fully connected signal and ground coaxial digital cables for optimum RCA digital signal transfer Optical S PDIF inputs Connect optical digital source to optical input Use good quality Toslink cables for optimum signal transfer RCA S
Download Pdf Manuals
Related Search