Compact C 2010 models Instruction Book
Contents
1. Pdf format are published regularly on our website www icoolsport com AUTOMATIC SYSTEM SHUTDOWN TIMER You can preset your iCool to shut down at any time up to five hours in the future This is very convenient for coaches and specialists who may want to leave the training area early but want Ag j to make sure that the system is not left running needlessly To set this time touch the SET Swit ee SHUT DOWN BUTTON and the clock digits on the bottom right of the screen will begin to flash SET as with setting the clock Use the same up down and left right arrows to set the number of hours and minutes you wish to elapse before the system automatically shuts down The system automatically begins the countdown and will stop when the time you set reaches zero The time remaining before shutdown is displayed on the main clock display screen As the same arrows are used to set all three time functions to avoid confusion a red dot appears next to be button of the function being set SHUT DOWH A very popular and useful feature of your iCool is the SESSION COUNTDOWN TIMER This allows you to accurately control the immersion times of athletes and to repeat those times as often as need ed This is an essential part of successful cryo recovery therapy and is just as important as maintaining accurate and consistent temperatures which of course your iCool does perfectly The session timer is set up from the main TIME SETTING SCREEN by touchin2. a full colour high resolution touchscreen that eliminates all switches and provides complete control over your iCool system in a user friendly and intuitive manner It also provides a substantial amount of additional information to assist you the latest software from its memory card and run a diagnostic self test routine This will take about 20 seconds During this time you will see this screen and then a black screen THE STATUS BAR WILL FLASH WHITE The STATUS BAR on top of the iCool changes colour or flashes to give a clear indication of each function While the software is loading the status bar will flash white while the screen shown above and then a black screen appears for about 15 seconds while the computers test the safety systems Then the status bar will stop flashing and show a steady white light to indicate that the systems check was successful and it is ready to use THE STATUS BAR LIGHT IN MOST CASES A PERSONAL LOGO WELCOME SCREEN WILL APPEAR AT THIS TIME Sri anka deal emg T C ricket INSTITUTE OF SPORT h Seto WELCOME RACE ENGNEERING PLEASE TOUCH THE SCREEN ANYWHERE TO PROCEED TOUCH THE SCREEN ANYWHERE TO CONTINUG ABOVE ARE EXAM PLES OF TYPICAL CUSTOMER LOGO WELCOME SCREENS Touch the logo screen anywhere to continue This will lead to the HOME screen The HOME screen offers several choices to Begin operation Set the system settings Set the time clock or Get assistance from the built in HEL
3. any time by touching the STOP PUMP BUTTON Alternatively you can stop everything by touching the ALL STOP BUTTON Alternatively you can simply switch off the main power If you use the ALL STOP BUTTON the fan may continue to run for a short time to cool the cabinet CURRENT POOL TEMERATURE EMPTYING THE POOL USING THE BUILT IN PUMP You can use the main circulating pump to empty the water from the pool by detaching the top hose from the top of the pool and directing it to a drain The pump can be turned on and off at any time using the pumps STOP START button DETAILED OPERATION THE TOUCH BUTTON FUNCTIONS SYSTEM SETTINGS When your iCool start up the first screen you will see offers you a SYSTEM SETTINGS button OPTIMUM SETTINGS ARE AUTOMATICALLY SELECTED so there usually no need to use this feature The three settings you can change are the fan speed range the temperature from degrees Centigrade to Fahrenheit and the sound level from the screen MAIN COOLING FAN SPEED This allows you to set the main cooling fan to either NORMAL or QUIET MODE Generally you should always leave it in the NORMAL mode which is fully automatic and allows the system to control the fan speed to give the very best efficiency and fastest cooling i e Eoo If you are in a very quiet environment you can select QUIET MODE but you must be aware that this will reduce the cooling ability of the system however it will be quieter overall as the fan wi
4. easy to use Make sure that the small clear plastic in line filter in the hose carrying water from the pool to the iCool is in place and is clean as this prevents contamination such as hair or fabric particles from clogging the heat exchange mecha nism The end of the hose that contains the filter is connected to the cooling system not the pool Also the white perforated inner filter membrane inside the clear filter housing must be installed in the correct direction or it will block the flow of water It is correctly installed when it is held in place by the screw fitting it should not float about inside the clear filter housing STEP 2 Fill the pool with clean fresh water not saltwater to the level marked on the pool liner Never use chlorine or bro mide solutions as these chemicals can attack the stainless steel heat exchange panels that remove heat from the water Because the water is very cold bacteria is not normally a problem for one or two days use If you intend to use the pool for longer periods without changing the water then you should use an inexpensive iCool compact ultraviolet sterilising unit or for permanent use a full iCool self powered filtration and sterilising unit Your iCool is fitted with both an automatic and a manual air romoval bleed valve see a full description on page 2 that will normally bring the water flow to full force in 1 to 2 minutes providing you meet the conditions set out below Normal water flow from your i
5. power switch to shut off instantly After a successful test reset the main switch to ON to begin normal operation If pressing the test button fails to instantly shut off the power switch DO NOT USE THE SYSTEM until you contact iCool for advice Failures of this system are very rare a Updates in Pdf format are published regularly on our website www icoolsport com ADVICE ABOUT OBTAINING THE CORRECT FLOW OF WATER Water flow through your iCool is produced by a high quality long life circulating type pump that for safety is completely isolated electrically from the water Circulating type pumps can lift and move water reliably for many thousands of hours however they do not pro vide suction and are therefore not self priming Self priming type pumps are generally not as reliable over long periods and so are not suitable for this type of system This means that the pump in your iCool can not begin to operate unless it is fed with a head of water above the pump and any air tapped in the system is removed The water in the pool must be above the water inlet con nector on your iCool cooling system before you start to pump Furthermore there must be no air trapped in the supply hose and no part of the hose from the pool to the cooling system can be above the level of the water as this traps air which can prevent water from flowing Water pumps can not operate for long periods without water as the water provides the lubrication To
6. water temperature setting Whichever method you choose it eventually takes you to the main run screen If you make no setting the system will automatically insert 15 C around 59 F In this case you would navigate directly to the main run screen in order to access and start the pump and cooling system If you want to use your previous setting from the CLAW last session you can touch the USE PREVIOUS ddi SETTING button and the last setting you used will scrap marara S be automatically inserted into the system Previous settings may have been lost if you have removed to mains power MAKE HEW SETTINGS www iCoolSport com te 14 uo 27 If you want to make a new setting which is the most common choice users make you touch the MAKE NEW SETTINGS BUTTON and this will take you to the screen illustrated above where you can use the up and down arrows to select the temperature you require After you make your setting touch of the start button to go to the main screen where you can start both the pump and the cooling system and where all relevant temperature information is clearly displayed CURRENT POOL TEMERATURE WATER TEMPERATURE FULL SCREEN TEMPERATURE LIMITATIONS Because of the dangers of hypothermia in the case of an unattended athlete using the pool your system will not allow you to set temperatures below 5 C 40 F If the model you are using is the Q contrast model which also provides he
7. with the colourful touchscreens As with any sophisticated piece of equipment when people start pressing buttons at random anything can happen Your iCool has many safety features to prevent a person tampering with the system from causing a disaster but most of these safety features involve Automatically shutting down the system which of course is undesirable We have covered this by installing a secret locking routine It is a good idea to keep this secret to as few people as possible To lock the screen so that no further inputs can be made touch and hold the iCool icon on the main run screen for more than 10 seconds you can only lock from this main screen A picture of a lock will appear While ever this lock is visible it is not possible to make any inputs or to change screens To unlock the system and returned to normal repeat the procedure Touch and hold the iCool icon for more than 10 seconds The lock will disappear and all functions will return to normal Page 13 lt iCool USER MANUAL FOR iCOOL RECOVERY SYSTEM Updates in Pdf format are published regular on our website www icoolsport com EMERGENCY OVERRIDE PROVISIONS CERTAIN SAFETY FEATURES IN YOUR ICOOL CAN BE OVERRIDDEN IN THE EVENT OF A PARTIAL FAILURE ICool systems are very reliable and have attained an excellent reputation around the world for this In addition we have done all that we can in the designs to build in ways to work around any partial failure s
8. ATER FLOW CAN ALSO STOP IF THE HEAT EXCHANGER TANK IS FROZEN SOLID If you set the temperature below about 7 C or 45 F it is occasionally possible in certain climatic condi tions for the heat exchange tank to freeze solid which will block most but not all of the flow of water A small amount of water may still be flowing through the automatic air bleed system which bypasses the heat exchanger but the safety system monitors the heat exchanger tank flow only and if no water is flowing through the tank the system will stop In order to cool the pool water to these extremely low temperatures the system must cool to at least 5 re below the set temperature and this takes it very close to the temperature that water freezes solid Following international safety standards your iCool will not accept water ee settings below 6 C or 42 F as this would put athletes using the system unattended at risk of hypothermia However the iCool is easily powerful enough to freeze the water inside the system itself and if this happens the safety screen above will appear and the system will stop Please be aware that the tank can only freeze if your setting is below 7 to 8 C and this can only hap pen in certain conditions If your set temperature is above this then it is much more likely that the system has stopped because of a lack of water flow caused by either a hose or filter obstruction or an air leak in the hoses or trapped air in the system If there is a
9. Cool will fill a standard water bucket in about 1 minute i q i Te e E E og poy ULL E eS The water level in the pool must be above the water inlet and outlet connections on the iCool The iCool must be on the same level surface as the pool It must not be above the pool WATER FLOW WARNING If water does not flow correctly after 3 minutes either during the initial set up or at any time during normal operation an alarm will sound THE SYSTEM WILL STOP TO PROTECT THE PUMP and a red warning screen will appear with instructions You must find the reason for the lack of water flow or the system will stop every 3 minutes for safety until the water flow is correct IF THE WATER FLOW WARNING APPEARS Please check to see that the hoses are not bent or blocked under heavy objects and that the lower hose is not higher than the water in the pool at any point as this will trap air The red screen that will appear gives you 2 options see the illustration on the next page Normally you would touch the RESTART PUMP button and then bleed the system again by referring to the in structions above and the advice about water flow on page 2 In most cases this will fix the problem an return the system to normal operation If all the trapped air is not removed by the automatic system or the manual bleed valve you can also remove the top hose fit ting from the cooling system for a few seconds while the pump is running u
10. ER TANK soldered soldered soldered s s Ye STAINLESS HANDLES Ye AREA LIGHTING Yes 10 Watts Yes 10 Watts Yes 20 Watts TOUCH SCREEN PUMP S STEEL SHIELDED minute pre set minute pre set minute pre set DIMENSIONS H W D in mm 545x475x290 545x475x290 545x475x290 DIMENSIONS H W D Inches 21 5x18 7x11 4 21 5x18 7x11 4 21 5x18 7x11 4 Please note iCool Systems are sold all around the world and these specifications may be different for units delivered in your country due to local conditions or regulations We are constantly improving our products and therefore certain specifications may change due to ongoing research and development We welcome your feedback and suggestions and we offer support for general enquiries and information for specific countries on our website at www iCoolSport com Thank you for choosing iCool the world s most popular ice bath therapy and recovery systems
11. G SCREEN The POOL TEMPERATURE window shows the actual water temperature returning from the pool This will vary slightly to the actual temperature in the pool because for safety reasons the electronic sensor is in the cool ing unit not in the pool It accurately reads the actual temperature of the water that is returning to the pool The actual pool temperature will be slightly different depending on your particular setup The temperature is always accurately maintained but if you want to display the actual pool temperature within 1 degree you can simply set an offset amount to compensate for the difference when selecting your reuired temperature The HEAT PUMP TEMPERATURE window shows the temperature inside the cabinet If this exceeds 70 C or 158 F the system will shut down an alarm will sound and a warning screen will appear This could happen in extremely hot conditions or if the unit is covered by an object such as a towel or anything that prevents proper airflow The OUTSIDE TEMPERATURE WINDOW shows the current room or outside temperature It is not desirable to operate this system in temperatures above 42 C or 108 F If the reading exceeds this you need to move the sys tem to a cooler area or improve the air flow The PRESET TEMPERATURE WINDOW always shows your selected temperature This is the temperature the water will be automatically cooled or heated to and maintained at CHANGING THE TEMPERATURE SETTING You can change your preset
12. P menus THE HOME SCREEN a lt iCool ALL MODEL C COMPACT MODELS FROM AUGUST 2009 Updates in Pdf format are published regularly on our website www icoolsport com The home screen provides many options which are covered elsewhere in this manual however to quickly start the system you need only select either the USE PREVIOUS SETTINGS button or the MAKE NEW SETTINGS but ton The system remembers your last pool temperature settings but if you have not used it before or if power has been removed since your last session it will default to either 10 C or 15 C 59 F These are the most common temperatures used ys it for recovery sessions The temperatures can be displayed in Cen y lt 4 g0 Re tigrade or Fahrenheit This is explained later in this Manual a oo ards For your first quick start you should touch the MAKE NEW Belton ins Tan SETTINGS button This will take you to the screen that allows you j gt i to set the pool water temperature that you require Simply touch the up and down arrow buttons and the desired pool water tem perature will appear on the bottom left hand of the screen in the 3 0 blue window marked SELECTED TEMPERATURE The right hand side of the screen shows the outside air temperature AA aJ ee ello Pogisa A Hiili 1 WATER TEMPERATURE SETTING SCREEN Once the pool water temperature you want your iCool to cool to is showing touch the START button This
13. Page 1 USER MANUAL FOR ICOOL RECOVERY SYSTEM A MARFII A MAALRARPAM MARnrI C FDAN AIICILIICT SAAD aN l l A ein l C CAO DAC f Ci l Q E R J A l iC j Q ZOO AN Vin J a amp gt J wa me Vial pp bu Au JIVI AA L5E f LU hy ALL MJU CGL O UVUNIPAU NIVVELO FAVUNI AUY U3 GUUS Updates in Pdf format are published regularly on our website www icoolsport com THERE ARE THREE VERSIONS OF THE ICOOL COMPACTS OMPACT Cool is our most popular and economic system It provides rapid cooling fully automatic control and excellent mobility OMPACT Dual Temp provides all the power and function of the Cool plus both cooling and heating automatically for advanced contrast therapy sessions OMPACT Twin is the most powerful mobile ice bath cooling system available It has all the features of the Cool plus extra cooling power and stronger water flow for cooling 2 pools at once if required or for cooling spa baths and larger iCool Demountable multi person pools ue THE OPERATION OF ALL 3 MODELS IS THE SAME EXCEPT WHERE NOTED se IN THIS MANUAL MODEL COOLING POWER HEATING POWER VOLTAGES AVAILABLE COMPACT Cool 3000 Watts 220 240 OR 110 COMPACT Twin s100wats 22o2400R 110 IMPORTANT SAFETY ADVICE POWER SUPPLY VOLTAGE iCools can only be used with the voltage marked on the machine they are not multi voltage The voltage is marked next to the main power socket O ENS
14. URE SAFE OPERATION THE POWER OUTLET YOU USE MUST HAVE A PROPER EARTH CONNECTION BUILT IN SAFETY SYSTEMS Your iCool system has many safety features to protect against such things as a loss of water flow overheating of the system or any chance of the user receiving an electrical shock If any such potentially dangerous things should occur in most cases your iCool will shut itself down and a red warning screen will appear to assist you o identify and correct the problem In the case of overheating the main fan will continue to run for some time until the temperature is safely back to normal For the safety of users any leakage of even a small amount of electrical current will cause the system to Instantly remove all electrical power In the unlikely event that your system shuts itself down for any of these reasons you must identify and correct he problem that has caused the safety systems to operate before allowing anyone to use the system PLEASE TEST THE EARTH LEAKAGE SAFETY DEVICE REGULARLY he main power switch is also part of the electrical safety circuit that can prevents the possibility of electric shock It is essential to test this safety system each time you use the iCool to make certain it is operating correctly This is very easy to do and takes only a few seconds urn on the main switch and then press the orange test button just above the switch If the safety system is working normally pressing the test button will cause the main
15. ating for contrast therapy you cannot set the temperature t above 45 C 112 F because of the risk of scalding These temperature limits have been set after TIMER wide consultation with the sporting industry around the world There are no demonstrated benefits ae in a water temperature lower than 5 C or above 45 C and therefore the risk of doing so is not justified TIMING FUNCTIONS Your iCool offers a number of very useful timing functions including a real time clock a countdown timer to time recovery and training sessions and a timer to shut down the system automatically at a predetermined time after use To set up and use hii these functions touch the TIMER FUNCTION button ao onthe home screen You can reach this screen by f using the BACK 1 button or the HOME button In order to use these functions you first need to set the time of TIME SETTING SCREEN day on the built in clock To set the clock touch the SET MAIN CLOCK button on the timing functions screen and the time setting display on the bottom right of the screen will begin flashing You must set it while one of the numbers is flashing by using the up down and left right keys Once you stop using these keys for more than a few seconds the display will stop flashing and the time showing is set into the system and the clock begins operating The iCool clock operates in the universal 24 hour time style ALL MODEL C COMPACT MODELS FROM AUGUST 2009 Updates in
16. completes the setup and takes you to the main run screen which is the screen that you will use most of the time during normal operation STEP 5 Touch the START PUMP button This will start the pump operating and water should begin circulating NOTE When you touch START buttons they change to STOP buttons and can then be used to STOP that function if required IT IS ESSENTIAL THAT THE WATER IS FLOWING CORRECTLY BEFORE YOU TOUCH THE SYSTEM START BUTTON The water flow is pre set to an optimum flow of about 20 litres or around 5 gallons per minute This allows time for the heat exchang7__ er to operate at maximum cooling efficiency a Srn Pool water is completely changed approximately every 15 minutes MAIN OPERATION SCREEN Do not touch the system button until you are sure that water is flowing smoothly If water does not flow smoothly within a couple of minutes please check that the hose from the bottom of the pool is flat on the floor and no part of it is higher than the top of the water Check that the water in the pool is higher than the inlet connectors on the iCool If this does not correct the problem the system will sound an alarm and a red warning screen will appear with information about how to correct the water flow problem STEP 6 Now that you have pre set your desired temperature and started the circulating pump the touch screen should look like the picture below of course the temperatures may be different Notice that the pu
17. d cause a total system failure that can not be covered by your warranty These chemicals eat away most met als and are are also damaging to athletes For total control of bacterie use an innexpensive iCool Ultra Violet Steraliser unit This is the totally safe way to deal with bacteria and keep your pool safe without using expen sive and potentially damaging chemicals Avoid prolonged use of salt water to ensure long life of your system QUICK START GUIDE The following is a quick start guide to get your iCool up and running quickly however it is strongly advised that you read the rest of the manual as it contains a lot of information that you really need to know to get the most out of your system STEP 1 Before you turn on your iCool system you must set up and fill the pool iCool portable inflatable pools and semi permanent demountable pools come with their own instructions and are easy to set up Just be sure that they are in the position you require before you fill them with water as the weight of the water will make it impossible to move them once they are filled Page 3 USER MANUAL FOR iCOOL RECOVERY SYSTEM ALL MODEL C COMPACT MODELS FROM AUGUST 2009 Updates in Pdf format are published regularly on our website www icoolsport com Before you fill the pool you must connect the 2 hoses provided The connections are clearly marked on both the pool and the iCool system ICool hoses have convenient snap fittings that are very quick and
18. eryone reports ee ee after regular use of ice bath recovery systems Of course this feature has no effect if you re particular Cool model does not have a sound system built in ME Po fami eS aml om on a POTIN PIH pE FE E m E E E m E y yor i ee ae aj i To activate the sound system touch the button which is available on several screens This takes you to a simple sound control screen that turns the amplifiers and speakers on and off Plug in any music player to the mini phono jack provided The volume is controlled by your music player not by iCool stereo system so be sure the volume is turned down when you first plug in your player Your iCool has an extensive built in electronic help e system Detailed and well illustrated helpful infor i mation on every important subject to do with the operation of your iCool is available from almost wi any screen simply by touching the help button Touching any help button will take you to the screen illustrated on the right The screen has eight menu buttons covering all of the important topics you are ever likely to need assistance with When you touch the menu button covering the topic you need assistance with the screen will change to a series of pages covering that subject Sample screens are illustrated below and opposite ALL MODEL C COMPACT MODELS FROM AUGUST 2009 Updates in Pdf format are published regularly on our website www icoolsport com You can f
19. g the SET COUNTDOWN button The numbers on the setting screen in the bottom right hand corner will begin to flash and you can use the left right and up down arrows to change the time in minutes and seconds Once you have set the time you want your athletes to remain in the bath touching the DISPLAY COUNTDOWN FULL SCREEN button will take you to the screen illustrated below This screen allows you to see the countdown from a distance and also to control it in various convenient ways The current pool temperature and the outside temperature will also be displayed The count down can be set for once only or it can repeat automatically as many times as you like This is particularly convenient if you have a number of athletes using the same pool at the same time The system beeps for each of the last five seconds the end of each countdown to warn the athletes to get ready to get either in or out of the pool and pauses for several seconds to allow the changeover before the count down begins again if it is set in the repeat mode Resets time to the preset value in the single shot mode ready to start again by press ing the START button When this button is pressed the countdown will repeat until the repeat function is cancelled by pressing once again A red dot indicates that it is active TIME REMAINING You can pause the count down at any time and start again from the same position with this button or touch reset to star
20. lip forward or backwards from page to page using the buttons on the right hand side of the help screens or you can return to be main help menu page at any time The built in illustrated help system is a revolutionary new idea and we are constantly updating it as new information and new feedback comes in from all over the world from iCool clients and from our recovery research programs in several countries Some help pages may not be installed on your iCool when it is delivered so that your local dealer can in stall them to suit your country and sport Aternatively iCool can provide a free update memory card with the latest help menus to suit your needs lt iCool INFLATABLE POOLS Page 2 P 4 iCool sabres ONEA f i i e i Sawa the attached capt ania ageh alt waiva lo probasi tha vajra objects ai cece pouliond fo our semi etry ting Hi Blasi Keel paoia have a line whieh indhenten the snerast seater lene it in vary important not to ovar ful as the to iaid the T f aa Sa aans Reet edad am q iCool INFLATABLE POOLS Page 1 i Hii TRAN ag pet ma genet een TE i Tops DEW no nemi in ji You may need a free local upgrade memory card to access all help files for your region YOUR iCOOL HAS AN ELECTRONIC LOCK As you can see iCool Systems have attractive user interfaces this makes them easy and very intuitive to use but the downside is that untrained people some times like to play
21. ll not run higher than 60 of maximum unless there is a risk of overheating in which case the safety system will turn the fan back to high no matter what the setting The NORMAL setting is used to give absolute maximum cooling power where higher fan noise is not a problem On a normal day this gives about 25 more cooling than in the QUIET MODE If cooling seems lower than normal check to see if this feature was previously set to Quiet Mode FIE REU TA EERE EITE RA TE LP ee A ELEC HFE TIEL EP AN EN CEILE Er ET ee TEMPERATURE DISPLAY SCALE This can be set to either Centigrade or Fahrenheit and this changes all of the displays throughout the entire system When you first start the iCool it will normally start in Centigrade as this is the world standard Due to complex decimal calculations between C and F there may be minor difference in the true F displays This has no effect on actual cooling accuracy The SOUND LEVEL adjusts the sounds made by touching the screen and by the alarms Normally it should be left on high to assist with settings and to make sure alarms are heard A red dot indicates which setting is selected in each of the available settings Page 9 USER MANUAL FOR iCOOL RECOVERY SYSTEM ALL MODEL C COMPACT MODELS FROM AUGUST 2009 Updates in Pdf format are published regularly on our website www icoolsport com iCoo TEMPERATURE SETTINGS When your iCool starts up you are offered 3 different ways to choose a
22. mp button has changed from START to STOP You can use this same button to start and stop the pump at any time Now touch the START SYSTEM button and the cooling cycle will begin The water will be cooled to your preset temperature and the system will cycle to maintain it at that temperature automatically The SYSTEM can only be started once within any 3 minute period to avoid overloading the compressor If you don t hear it start do not touch the START SYSTEM again it will start automatically after the 3 minutes safety period elapses If your iCool is the CONTRAST MODEL then depending on the temperature you set it will either heat or cool the water automatically to reach your preset temperature and then maintain it at that temperature More detailed information about the operation of the CONTRAST version can be found later in this manual FOR THE SAFETY OF USERS YOU CAN NOT SET TEMPERATURES BELOW 5 C OR ABOVE 45 C 40 F 112 F IN AN EMERGENCY YOU CAN STOP ALL FUNCTIONS IMMEDIATELY BY TOUCHING THE ALL STOP BUTTON however if the cabinet is hot the fan may continue to run until the cabinet has cooled Page USER MANUAL FOR iCOOL RECOVERY SYSTEM ALL MODEL C COMPACT MODELS FROM AUGUST 2009 Updates in Pdf format are published regularly on our website www icoolsport com t cy BACK 1 LIGHTS J SOUND START START F Y amp us STOP START PUMP SYSTEM ad MAIN OPERATION SCREEN DETAILS OF THE MAIN OPERATIN
23. n still use your iCool for that important event Realistically even the best electronic systems occasionally have problems especially in portable systems that have a relatively hard life Fortunately we have very few such problems but as an added benefit we have built into all iCool s a com plete manual override system that allows your iCool to operate effectively even if all of the main electronics fail for whatever reason We do not publish this over ride information in the manual because it is a little different from model to model but in the rare event that you ever have a failure of the electronics which prevents you from operat ing your iCool just call or e mail the local iCool representative in your country or our international number or go to our web site www iCoolsport com where you will find a listing of representatives around the world or you can request areply directly from our headquarters You will be contacted promptly and we will explain how to work around your problem until we can arrange repairs This is an important service that we hope you never need but it s good to know it is there In addition to this service you will be pleased to know that your iCool is of a modern modular design which means that most components can be easily replaced in the field and often by the owner SPECIFICATIONS COOLING POWER 3200 Watts 3200 Watts 5000 Watts HEATING POWER _ 2400Wats 14 Amps 26Amps EXCHANG
24. ntill the air escapses This is not normally necessary but can help in diffcult situations lt iCool The Water Flow Warning Screen also 7 provides an option to over ride the flow protection system in the rare situation WARNING 7 te of a false alarm WATER IS NOT FLOWING or EXCHANGER TANK IS FROZEN Updates in Pdf format are published regularly on our website www icoolsport com NEVER USE THIS OPTION UNLESS YOU THE WATER PLOW SAFETY SENSORS INDICATE THAT WO WATER ES FLOWING IN THE HEAT AD SVSTEMIS STOPPING BECAUSE OFA O A ae aA FALSE WATER FLOW ALARM OTHERWISE THE PUMP CANNOT RECEIVE WATER FROM THE POOL ALSO MAKE SURE THAT NO Once you use this function to disarm Stare a ean ase air ee n nen the flow safety monitor nothing will FROZEN SOLID THIS ES POSSIBLE IF THE ICOOL IS SET TO AN EXTREMELY LOW TEMPERATURE BELOW 8 C 45 F IN THES CASE WO FURTHER COOLING IS POSSIBLE UNTIL THE ICE IS CLEARED stop the system even if water is not TURN OF THE UNIT AND LEAVE IT FOR AT LEAST 20 MINUTES TO LET THE ICE MELT THIS OILY OCCURS RARELY AT VERY LOW TEMPERATURES RESET TO A HIOHEA TEMPERATURE TO AVOID ELEM flowing and this can seriously damage SG the pump as it will have no lubrication WWW ICOOLSPORT COM or cooling from the water This over ride function is only to be used for short periods where it is essential to keep your system operating until the reason for the false alarm can be determined and corrected W
25. o that you are not prevented from using your system for an important event There are some circumstances in which it would be acceptable to temporarily override certain safety systems that may become too sensitive and cause trouble until they can be properly readjusted This allows systems to continue to operate in circumstances where otherwise it might not be possible Of course we do not allow the overriding of electrical safety cir cuits this is not acceptable under any circumstances For example depending on the way your system has been set up it sometimes occurs that the water flow monitoring system may be too sensitive and will stop the pump because it appears that water is not flow ing properly We allow this to be over ridden if it becomes troublesome Instructions on how to do this will appear on the screen automatically if this happens It must be remembered of course that if you disarm this system the pump is no longer protected from running dry and therefore without lubrication so it is essential that you manually monitor the water flow Our staff can assist you by phone or e mail to overcome most problems on the spot EVEN IF THE ENTIRE TOUCHSCREEN USER INTERFACE FAILS WE CAN USUALLY STILL GET YOU GOING In our efforts to remain the world s number one supplier of mobile ice bath systems we have continued to improve reliability but we have also engineered ways to ensure that no matter what happens in the field in most cases you ca
26. possibilty that the heat exchanger tank is frozen then you must allow the system to warm up for about 30 minutes to thaw the ice Leave the power switched on so that the fan can operate if Hare to thaw out the tank Set a new temperature no lower than 8 or 9 C before restarting so that the tank does not freeze again STEP 3 Connect the power cable provided with your iCool to a standard power outlet capable of providing at least 12 amps in countries with a 220 V supply and 24 amps in countries with a 110 V supply Although the system requires much less power than this in normal operation all heat pump compressor motors need considerably more power for a minute or so each time they starts up FOR SAFETY THE POWER OUTLET YOU USE MUST BE EARTHED CORRECTLY The main power switch is also part of the electrical safety circuit that prevents the possibility of electric shock It is a good idea to test this system each time you use the iCool by turning on the main switch and then pressing the test button above the switch If the safety system is working normally pressing the test button will cause the main power switch to shut down instantly After this test reset the main switch to ON to begin normal operation Page 5 USER MANUAL FOR iCOOL RECOVERY SYSTEM ALL MODEL C COMPACT MODELS FROM AUGUST 2009 Updates in Pdf format are published regularly on our website www icoolsport com STEP 4 YOUR SYSTEM SOFWARE WILL BEGIN LOADING Your iCool has
27. prevent damage your iCool system will shut down the pump if water is not flowing properly for more than three min utes If this happens a warning screen will normally appear to explain to you how to correct the problem To assist in removing trapped air quickly our iCool is fitted with an automatic air bleed system plus a manual air bleed valve on the rear of the unit at the bottom Once you have connected the hoses as described in this manual and started the pump if water does not flow at normal force after 2 minutes open the air bleed valve and allow water to escape TTT This valve is directly connected to the pump body and any trappeed air will be removed It could take up to 2 minutes although normally a few seconds is enough Once water is flowing back to the pool normally close the air bleed valve Normal flow will fill a standard bucket in about 1 minute If you are using the system in an area where you can not let water run on the floor please attach the small 12 mm diameter hose provided and run the bleed water into a bucket IT WILL NOT ALWAYS BE NECESSARY TO BLEED THE SYSTEM AND IF YOU NEED TO DO SOIT WILL ONLY BE NECESSARY ONCE FOR EACH SET UP Once primed of air the system will remain primed until it is emptied or moved and water will normally flow instantly each time you start the pump NEVER USE CORROSIVE CHEMICALS These chemicals can cause major damage even to the high grade stainless steel heat exchanger in your iCool an
28. t from the top This button starts the countdown 7a BITATE TEMPERA TORE Page 11 USER MANUAL FOR ICOOL RECOVERY SYSTEM Updates in Pdf format are published regularly on our website www icoolsport com All iCool models have convenient area lighting which is very helpful if the area around your pool g ka ic arrangement is not well lit The lights can be Pa n f am activated from a simple lighting control screen x The lighting control screen can be accessed from noe several screens by touching the button EXTERNAL LIGHTS This Takes you to a simple screen that has both ON and OFF light icon buttons When you touch the on button the area lights illuminate and a red dot beside the icon indicates that the lights are set on Simply reverse the procedure to turn the lights off If the lights are activated they do not turn off when you touch the all stop button or when the system initiates a safety shutdown This allows an extra measure of safety by continuing to light the area even if a fault has been detected Some iCool models have a very high quality stereo e Eo e 4 ic sound system built in to allow athletes to plug in MARL STEREO SYSTER D ts their iPods or MP3 players or any other entertain ment devices and listen to powerful quality sound while they use the iCool recovery system This has m been a very popular feature and contributes to the r a ra general feeling of well being that ev
29. temperature at any time by touching the CHANGE SETTING BUTTON this will take you to the change settings screen From here you proceed as described previously If you have the CONTRAST model for safety reasons you cannot change directly from heating to cooling or cooling to heating To do this you must switch off the entire system at the main switch and start again This is required to reset the computer FAN SPEEDS During normal operation the main fan will automatically change speeds as required to maintain the highest efficiency The fan will be at full soeed when temperatures are high or the water is warm Al MODEI C O MPACT MODEI G EROM ALIGLIST 2009 Updates in Pdf format are published rec KiCool YOU CAN DISPLAY THE POOL TEMPERATURE AT FULL SCREEN SIZE If you touch the number in the pool temperature window on the Main Operation Screen for a few seconds the screen will change to a full screen display of that temperature This is useful if you wish to monitor the system from a distance The pre set temperature and the outside temperature continued to display in smaller windows for your reference To return to the main operating screen touch the BACK 1 button TO STOP THE SYSTEM AT THE END OF YOUR RECOVERY SESSION 10 There are several ways to stop the system and close it down ite You can stop the cooling system by touching the STOP SYSTEM button in this case the pump will continue to run however you can stop to pump at
Download Pdf Manuals
Related Search